Commit graph

752,023 commits

Author SHA1 Message Date
Chris Zhong
866d4087f3 phy: rockchip-typec: support DP phy switch
There are 2 Type-c PHYs in RK3399, but only one DP controller. Hence
only one PHY can connect to DP controller at one time, the other should
be disconnected. The GRF_SOC_CON26 register has a switch bit to do it,
set this bit means enable PHY 1, clear this bit means enable PHY 0.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:35 +05:30
Chris Zhong
5eac5e9c0f phy: rockchip-typec: force to USB2 if DP at 4 lanes mode
The usb3tousb2_en BIT will be clear to 0 in probe(), it make USB
controller work at USB3 mode, and if the USB phy is turned on with DP
only mode(4 lanes DP), the rockchip_usb3_phy_power_on() will return
directly, so usb3_host_disable and usb3_host_port these 2 BIT will keep
a same value as coreboot. In coreboot, these 3 BITs are set as USB2
mode, but now one of the bits is changed to USB3, it make USB controller
work at a unknown status.

These 3 BITs should be changed to USB2, if the Type-C works at 4 lanes
mode, and then switch it back to USB3 mode, when USB disconnect.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:34 +05:30
William wu
f293f7409f phy: rockchip-typec: enable usb3 host during usb3 phy power on
We have forced usb3 to work in usb2 only mode in firmware by setting
usb3tousb2_en (bit3 of GRF_USB3PHY0/1_CON0) to 1, and setting
host_u3_port_disable (bit0 of GRF_USB3OTG0/1_CON1) to 1 and host_u3_port
(bit15~12 of GRF_USB3OTG0/1_CON1) to 0. So we need to re-enable usb3
host.

Note that the RK3399 TRM suggests that we should keep the whole usb3
controller in reset for the duration of the Type-C PHY initialization.
However, it's hard to assert the reset in the current framework of
reset. And according to the TRM, it doesn't require that we should
clear the usb3tousb2 bit before pipe ready. So let's enable the usb3
host after pipe ready to avoid the Type-C PHY initialization failure.

Signed-off-by: William wu <wulf@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:33 +05:30
Enric Balletbo i Serra
6912d4f40b dt-bindings: phy-rockchip-typec: deprecate some register properties.
As now the following register properties are in the driver, document as
deprecated these properties and recommend to not use them on new bindings.

The deprecated properties are:

- rockchip,typec-conn-dir : the register of type-c connector direction
- rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2
                           enable control.
- rockchip,external-psm : the register of type-c phy external psm clock
                          selection.
- rockchip,pipe-status : the register of type-c phy pipe status.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:32 +05:30
Enric Balletbo i Serra
0fbc47d9e4 phy: rockchip-typec: deprecate some DT properties for various register fields.
Adding properties for various register fields in the DT doesn't scale and
this information should be in the driver instead.

Before this patch these registers (description below) were specified in
the DT, every register node contained 3 sections: offset, enable bit,
write mask bit.

 - rockchip,typec-conn-dir : the register of type-c connector direction,
   for type-c phy0, it must be <0xe580 0 16>;
   for type-c phy1, it must be <0xe58c 0 16>;
 - rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2
   enable control.
   for type-c phy0, it must be <0xe580 3 19>;
   for type-c phy1, it must be <0xe58c 3 19>;
 - rockchip,external-psm : the register of type-c phy external psm clock
   selection.
   for type-c phy0, it must be <0xe588 14 30>;
   for type-c phy1, it must be <0xe594 14 30>;
 - rockchip,pipe-status : the register of type-c phy pipe status.
   for type-c phy0, it must be <0xe5c0 0 0>;
   for type-c phy1, it must be <0xe5c0 16 16>;

After this patch these register definitions are in the driver. So can be
removed from the DT. Note that there are 2 type-c phys for RK3399 with
different offsets, the driver checks the phy base address of the running
instance and applies the right offsets.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:31 +05:30
Tony Lindgren
5d1ebbda03 phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4
Let's add support for the GPIO controlled USB PHY on the MDM6600 modem.
It is used on some Motorola Mapphone series of phones and tablets such
as Droid 4.

The MDM6600 is hardwired to the first OHCI port in the Droid 4 case, and
is controlled by several GPIOs. The USB PHY is integrated into the MDM6600
device it seems. We know this as we get L3 errors from omap-usb-host if
trying to use the PHY before MDM6600 is configured.

The GPIOs controlling MDM6600 are used to power device on and off, to
configure the USB start-up mode (normal mode versus USB flashing), and
they also tell the state of the MDM6600 device.

The two start-up mode GPIOs are dual-purposed and used for out of band
(OOB) wake-up for USB and TS 27.010 serial mux. But we need to configure
the USB start-up mode first to get MDM6600 booted in the right mode to
be usable in the first place.

Note that the Motorola Mapphone Linux kernel tree has a "radio-ctrl"
driver for modems. But it really does not control the radio at all, it
just controls the modem power and start-up mode for USB. So I came to
the conclusion that we're better off having this done in the USB PHY
driver. For adding support for USB flashing mode, we can later on add
a kernel module option for flash_mode=1 or something similar.

Also note that currently there is no PM runtime support for the OHCI
on omap variant SoCs. So for low(er) power idle states, currenty both
ohci-platform and phy-mapphone-mdm6600 must be unloaded or unbound.

For reference here is what I measured for total power consumption on
an idle Droid 4 with and without USB related MDM6600 modules:

idle lcd off	phy-mapphone-mdm6600	ohci-platform
153mW		284mW			344mW

So it seems that MDM6600 is currently not yet idling even with it's
radio turned off, but that's something that is beyond the control of
this USB PHY driver. This patch does get us to the point where modem
data and GPS are usable with libqmi and ModemManager for example.
Voice calls need more audio driver work.

Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:30 +05:30
Pengcheng Li
ba8b0ee81f phy: add inno-usb2-phy driver for hi3798cv200 SoC
It adds inno-usb2-phy driver for hi3798cv200 SoC USB 2.0 support.  One
inno-usb2-phy device can support up to two PHY ports.  While there is
device level reference clock and power reset to be controlled, each PHY
port has its own utmi reset that needs to assert/de-assert as needed.

Hi3798cv200 needs to access PHY port0 register via particular peripheral
syscon controller register to control PHY, like turning on PHY clock.

Signed-off-by: Pengcheng Li <lpc.li@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:29 +05:30
Pengcheng Li
d581ba62f3 dt-bindings: add bindings doc for HiSilicon INNO USB2 PHY
It adds device tree bindings document for HiSilicon INNO USB2 PHY.

Signed-off-by: Pengcheng Li <lpc.li@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:28 +05:30
Yoshihiro Shimoda
0147b57e73 dt-bindings: rcar-gen3-phy-usb3: Add bindings for r8a77965
This patch adds bindings for r8a77965 (R-Car M3-N).

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:27 +05:30
Yoshihiro Shimoda
44e42df6b9 phy: rcar-gen3-usb2: Add support for r8a77965
This patch adds support for r8a77965 (R-Car M3-N). This SoC has
dedicated pins.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:26 +05:30
Yoshihiro Shimoda
b1ba68f33c dt-bindings: rcar-gen3-phy-usb2: Add bindings for r8a77965
This patch adds support for r8a77965 (R-Car M3-N).

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:25 +05:30
Amelie Delaunay
94c358da3a phy: stm32: add support for STM32 USB PHY Controller (USBPHYC)
This patch adds phy transceiver driver for STM32 USB PHY Controller
(USBPHYC) that provides dual port High-Speed phy for OTG (single port)
and EHCI/OHCI host controller (two ports).
One port of the phy is shared between the two USB controllers through
a UTMI+ switch.

[fengguang.wu@intel.com: Make stm32_usbphyc_get_pll_params() to be static]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:53:00 +05:30
Chris Zhong
0a00ac97d2 drm/rockchip: cdn-dp: remove the DP phy switch
There are 2 Type-c PHYs in RK3399, but only one DP controller. Hence
only one PHY can connect to DP controller at one time, the other should
be disconnected. The GRF_SOC_CON26 register has a switch bit to do it,
set this bit means enable PHY 1, clear this bit means enable PHY 0.

If the board has 2 Type-C ports, the DP driver get the phy id from
devm_of_phy_get_by_index, and then control this switch according to
this id. But some others board only has one Type-C port, it may be PHY 0
or PHY 1. The dts node id can not tell us the correct PHY id. Hence move
this switch to PHY driver, the PHY driver can distinguish between PHY 0
and PHY 1, and then write the correct register bit.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[The phy-changes are in the phy-tree now and the cdn-dp wasn't
 enabled at all so far, so this change can go through drm-misc
 alone without causing issues when testing drm-misc]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180216120956.19034-6-enric.balletbo@collabora.com
2018-03-16 11:51:11 +01:00
Luca Coelho
86a2b2043a iwlwifi: add shared clock PHY config flag for some devices
Some devices use a shared clock which is very sensitive to variations
and cause trouble in some situations.  We need to set a bit in the phy
configuration to indicate that to the FW.  To make this generic, add a
extra_phy_config_flags element to the device configuration and OR it
into the phy_cfg before sending it to the firmware.  And also create a
set of configurations for devices that use shared clocks and need this
extra bit to be set.

Fixes: c62446d2b0 ("iwlwifi: add new 9460 series PCI IDs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-16 12:34:54 +02:00
Johannes Berg
75fd4fec3e iwlwifi: mvm: fix error checking for multi/broadcast sta
The earlier patch called the station add functions but didn't
assign their return value to the ret variable, so that the
checks for it were meaningless. Fix that.

Found by smatch:

.../mac80211.c:2560 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
.../mac80211.c:2563 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'

Fixes: 3a89411cd31c ("iwlwifi: mvm: fix assert 0x2B00 on older FWs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-16 12:34:53 +02:00
Beni Lev
e829b17caf iwlwifi: mvm: Correctly set IGTK for AP
Currently when an IGTK is set for an AP, it is set as a regular key.
Since the cipher is set to CMAC, the STA_KEY_FLG_EXT flag is added to
the host command, which causes assert 0x253D on NICs that do not support
this.

Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-16 12:34:52 +02:00
Emmanuel Grumbach
334167decf iwlwifi: mvm: set the correct tid when we flush the MCAST sta
The tid being used for the queue (cab_queue) for the MCAST
station has been changed recently to be 0 (for BE).
The flush path still flushed only the special tid (15)
which means that the firmware wasn't flushing the right
queue and we could get a firmware crash upon remove
station if we had an MCAST packet on the ring.

The current code that flushes queues for a station only
differentiates between internal stations (stations that
aren't instantiated in mac80211, like the MCAST station)
and the non-internal ones.
Internal stations can be either: BCAST (beacons), MCAST
(for cab_queue), GENERAL_PURPOSE (p2p dev, and sniffer
injection). The internal stations can use different tids.

To make the code simpler, just flush all the tids always
and add the special internal tid (15) for internal
stations. The firmware will know how to handle this even
if we hadn't any queue mapped that that tid.

Fixes: e340c1a6ef4b ("iwlwifi: mvm: Correctly set the tid for mcast queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-16 12:34:52 +02:00
Arnd Bergmann
79375ea3ec mm: remove obsolete alloc_remap()
Tile was the only remaining architecture to implement alloc_remap(),
and since that is being removed, there is no point in keeping this
function.

Removing all callers simplifies the mem_map handling.

Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 10:56:13 +01:00
Arnd Bergmann
1a8429132e mm: remove blackfin MPU support
The CONFIG_MPU option was only defined on blackfin, and that architecture
is now being removed, so the respective code can be simplified.

A lot of other microcontrollers have an MPU, but I suspect that if we
want to bring that support back, we'd do it differently anyway.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 10:56:10 +01:00
Arnd Bergmann
e05a959f4b procfs: remove CONFIG_HARDWALL dependency
Hardwall is a tile specific feature, and with the removal of the
tile architecture, this has become dead code, so let's remove it.

Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 10:56:08 +01:00
Jesper Nilsson
c690eddc2f CRIS: Drop support for the CRIS port
The port was added back in 2000 so it's no longer even a good source
of inspiration for newer ports (if it ever was)

The last SoC (ARTPEC-3) with a CRIS main CPU was launched in 2008.

Coupled with time and working developer board hardware being
in low supply, it's time to drop the port from Linux.

So long and thanks for all the fish!

Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 10:56:05 +01:00
Arnd Bergmann
bb9d812643 arch: remove tile port
The Tile architecture port was added by Chris Metcalf in 2010, and
maintained until early 2018 when he orphaned it due to his departure
from Mellanox, and nobody else stepped up to maintain it. The product
line is still around in the form of the BlueField SoC, but no longer
uses the Tile architecture.

There are also still products for sale with Tile-GX SoCs, notably the
Mikrotik CCR router family. The products all use old (linux-3.3) kernels
with lots of patches and won't be upgraded by their manufacturers. There
have been efforts to port both OpenWRT and Debian to these, but both
projects have stalled and are very unlikely to be continued in the future.

Given that we are reasonably sure that nobody is still using the port
with an upstream kernel any more, it seems better to remove it now while
the port is in a good shape than to let it bitrot for a few years first.

Cc: Chris Metcalf <chris.d.metcalf@gmail.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: http://www.mellanox.com/page/npu_multicore_overview
Link: https://jenkins.debian.net/view/rebootstrap/job/rebootstrap_tilegx_gcc7/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 10:56:03 +01:00
Arnd Bergmann
4ba66a9760 arch: remove blackfin port
The Analog Devices Blackfin port was added in 2007 and was rather
active for a while, but all work on it has come to a standstill
over time, as Analog have changed their product line-up.

Aaron Wu confirmed that the architecture port is no longer relevant,
and multiple people suggested removing blackfin independently because
of some of its oddities like a non-working SMP port, and the amount of
duplication between the chip variants, which cause extra work when
doing cross-architecture changes.

Link: https://docs.blackfin.uclinux.org/
Acked-by: Aaron Wu <Aaron.Wu@analog.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Mike Frysinger <vapier@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 10:55:47 +01:00
Ulf Hansson
f09a7931bc Merge branch 'fixes' into next 2018-03-16 10:06:19 +01:00
Daniel Borkmann
318df9f01c Merge branch 'bpf-tools-build-improvements'
Jakub Kicinski says:

====================
As promised this series addresses nits and minor issues in tools/bpf
build infra.  One GCC-7 warning which is nice to get rid of.  Dependencies
when built with OUTPUT are fixed.  make clean will now remove the
FEATURE-DUMP.* files.  PHONY target is also updated to match reality.
====================

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-03-16 09:25:11 +01:00
Jakub Kicinski
cc5b3403f0 tools: bpf: remove feature detection output
bpf tools use feature detection for libbfd dependency, clean up
the output files on make clean.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-03-16 09:23:46 +01:00
Jakub Kicinski
8050ea4653 tools: bpf: cleanup PHONY target
There is no FORCE target in the Makefile and some of the PHONY
targets are missing, update the list.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-03-16 09:23:31 +01:00
Jakub Kicinski
d5fc73dceb tools: bpftool: fix potential format truncation
GCC 7 complains:

xlated_dumper.c: In function ‘print_call’:
xlated_dumper.c:179:10: warning: ‘%s’ directive output may be truncated writing up to 255 bytes into a region of size between 249 and 253 [-Wformat-truncation=]
     "%+d#%s", insn->off, sym->name);

Add a bit more space to the buffer so it can handle the entire
string and integer without truncation.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-03-16 09:23:15 +01:00
Jakub Kicinski
90126e3a40 tools: bpftool: fix dependency file path
Auto-generated dependency files are in the OUTPUT directory,
we need to include them from there.  This fixes object files
not being rebuilt after header changes.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-03-16 09:22:55 +01:00
Amelie Delaunay
194303d60b dt-bindings: phy: add support for STM32 USB PHY Controller (USBPHYC)
This patch adds the device tree bindings description for STM32 USBPHYC
(USB PHY Controller).

Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 13:40:46 +05:30
Masahiro Yamada
bb0e500bed phy: add 'depends on HAS_IOMEM' to fix unmet dependency
These configs select MFD_SYSCON, but do not depend on HAS_IOMEM.

Compile testing on architecture without HAS_IOMEM causes "unmet
direct dependencies" in Kconfig phase.

Detected by "make ARCH=score allyesconfig".

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 13:40:45 +05:30
Martin Blumenstingl
115de9fd68 phy: amlogic: add USB3 PHY support for Meson GXL and GXM
This adds a new driver for the USB3 PHY found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).

Unfortunately there is no documentation for this PHY in the public S905X
datasheet (published for example by Khadas). What we know so far about
this PHY:
- even though the Meson GXL and GXM SoCs do not expose an USB3 port (the
  dwc3 controller only has USB2 ports enabled) we need to initialize the
  USB3 PHY (specifically USB_R1_U3H_FLADJ_30MHZ_REG_MASK). Without this
  initialization high-speed USB devices (especially USB hard disks and
  thumb drives, slower devices like mice do not seem to be affected)
- on some boards the USB3 PHY starts in "device mode" - we want to bring
  it into a known state (by switching it to host mode for now).
- it is responsible for the OTG detection and for switching the first
  USB2 PHY between host and peripheral (aka device) mode. an interrupt
  can be used to detect changes between host and device mode.

There are five inputs to this register area:
- the clock and reset line for the USB3 PHY itself
- the clock and reset line for the peripheral mode and OTG detection
  logic (on the GXL and GXM SoCs these are the same clock and reset line
  as for the USB3 PHY itself, but Amlogic sees this as two different
  components - even though they share the same register space - so they
  have to be passed individually to allow specifying different inputs on
  other SoCs if needed)
- the interrupt for the OTG detection logic

The whole OTG detection logic is not implemented yet.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 13:40:44 +05:30
Martin Blumenstingl
324e46cee1 dt-bindings: phy: Add support for the USB3 PHY on Amlogic Meson GXL SoCs
Amlogic Meson GXL SoCs use a dwc3 controller with two (GXM - a variant
for GXL, has three) USB2 ports. The first USB2 port supports host and
peripheral (also called "device") mode.
While the dwc3 controller has no USB3 port enabled we still need the
USB3 PHY to be initialized. Otherwise high-speed USB transfers (for
example with a USB flash drive) may time out (most often seen on boards
with mainline u-boot, where the bootloader does not initialize the USB3
PHY registers).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 13:40:44 +05:30
Alexander Monakov
ae3f672cab phy: berlin-usb: adjust USB_PHY_RX_CTRL init flags
Make the value written into the USB_PHY_RX_CTRL configuration register
match 0xAA79 value written by manufacturer-supplied kernels for Sony
NSZ-GS7 (Berlin2 SoC), Google Chromecast and Valve Steam Link (BG2CD).

This fixes timeouts communicating to the internal hub on Steam Link.

Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 13:40:43 +05:30
Chunfeng Yun
c55fbcb8cf dt-bindings: phy-mtk-tphy: add properties for U2 slew rate calibrate
Add two properties of ref_clk and coefficient used by U2 slew rate
calibrate which may vary on different SoCs

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 13:40:43 +05:30
Chunfeng Yun
8833ebf4f8 phy: phy-mtk-tphy: add configurable parameters for slew rate calibrate
There are two parameters, ref_clk and coefficient, for U2 slew rate
calibrate which may vary on different SoCs, here allow them to be
configurable

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 13:40:42 +05:30
Chunfeng Yun
4036325609 phy: phy-mtk-tphy: keep default value of mcu_bus_ck_gate_en
The default value of mcu_bus_ck_gate_en is 1, if clear it, will
prevent system to enter deep idle mode, so keep its default value
and without affecting PCIe function.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 13:40:42 +05:30
Alexey Khoroshilov
124380cb0e phy: lpc18xx-usb-otg: error handling in lpc18xx_usb_otg_phy_power_on()
If regmap_update_bits() fails in lpc18xx_usb_otg_phy_power_on(),
lpc->clk is left enabled.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 13:40:42 +05:30
Greentime Hu
6fc61ee694 nds32: To use the generic dump_stack()
Use the generic dump_stack() instead of nds32 one because they are doing
the same thing.

Signed-off-by: Greentime Hu <greentime@andestech.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 15:45:23 +08:00
Greentime Hu
e115807657 nds32: fix building failed if using elf toolchain.
OUTPUT_FORMAT is not necessary here and the elf toolchain doesn't
support these formats. Since kernel should be built pass with elf
or Linux toolchain. This can be removed from vdso.ld.S

These are the built failed messages.
  VDSOL   arch/nds32/kernel/vdso/vdso.so.dbg
  /home/users/greentime/tmp/nds32le-elf-newlib-v3-upstream-b224/bin/../lib/gcc/nds32le-elf/8.0.1/../../../../nds32le-elf/bin/ld:
  target elf32-nds32le-linux not found
  collect2: error: ld returned 1 exit status
  make[1]: *** [arch/nds32/kernel/vdso/vdso.so.dbg] Error 1
  make: *** [vdso_prepare] Error 2

Signed-off-by: Greentime Hu <greentime@andestech.com>
2018-03-16 15:45:22 +08:00
Greentime Hu
c601a89115 nios2: add ioremap_nocache declaration before include asm-generic/io.h.
A commit for the nds32 architecture bootstrap("asm-generic/io.h:
move ioremap_nocache/ioremap_uc/ioremap_wc/ioremap_wt out of ifndef
CONFIG_MMU") will move the ioremap_nocache out of the CONFIG_MMU ifdef.
This means that in order to suppress re-definition errors we need to
setup #define's before importing asm-generic/io.h.

Signed-off-by: Greentime Hu <greentime@andestech.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
2018-03-16 15:45:21 +08:00
Greentime Hu
d78a62fb34 nds32: fix building failed if using older version gcc.
It will be built failed because these options are not supported by older
version gcc.

Signed-off-by: Greentime Hu <greentime@andestech.com>
2018-03-16 15:45:20 +08:00
Joe Perches
99a954874e drm: Reduce object size of DRM_ERROR and DRM_DEBUG uses
drm_printk is used for both DRM_ERROR and DRM_DEBUG with unnecessary
arguments that can be removed by creating separate functins.

Create specific functions for these calls to reduce x86/64 defconfig
size by ~20k.

Modify the existing macros to use the specific calls.

new:
$ size -t drivers/gpu/drm/built-in.a | tail -1
1876562	  44542	    995	1922099	 1d5433	(TOTALS)

old:
$ size -t drivers/gpu/drm/built-in.a | tail -1
1897565	  44542	    995	1943102	 1da63e	(TOTALS)

Miscellanea:

o intel_display requires a change to use the specific calls.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/016b5cb84cede20fd0f91ed6965421d99fd5f2ce.1520978414.git.joe@perches.com
2018-03-16 08:41:57 +01:00
Evgeniy Didin
47b7de2f6c mmc: dw_mmc: fix falling from idmac to PIO mode when dw_mci_reset occurs
It was found that in IDMAC mode after soft-reset driver switches
to PIO mode.

That's what happens in case of DTO timeout overflow calculation failure:
1. soft-reset is called
2. driver restarts dma
3. descriptors states are checked, one of descriptor is owned by the IDMAC.
4. driver can't use DMA and then switches to PIO mode.

Failure was already fixed in:
https://www.spinics.net/lists/linux-mmc/msg48125.html.

Behaviour while soft-reset is not something we except or
even want to happen. So we switch from dw_mci_idmac_reset
to dw_mci_idmac_init, so descriptors are cleaned before starting dma.

And while at it explicitly zero des0 which otherwise might
contain garbage as being allocated by dmam_alloc_coherent().

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-16 08:38:54 +01:00
Taehee Yoo
46c0ef6e1e xfrm: fix rcu_read_unlock usage in xfrm_local_error
In the xfrm_local_error, rcu_read_unlock should be called when afinfo
is not NULL. because xfrm_state_get_afinfo calls rcu_read_unlock
if afinfo is NULL.

Fixes: af5d27c4e1 ("xfrm: remove xfrm_state_put_afinfo")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2018-03-16 08:26:02 +01:00
Dave Airlie
3a1b5de36f Only GVT fixes:
- Two warnings fix for runtime pm and usr copy (Xiong, Zhenyu)
 - OA context fix for vGPU profiling (Min)
 - privilege batch buffer reloc fix (Fred)
 -----BEGIN PGP SIGNATURE-----
 
 iQEcBAABAgAGBQJaqwRYAAoJEPpiX2QO6xPKZT0H/30rwEPNL0Z9LMrZY/WC4Yr8
 0Hbc7jn0pYgCV+Cm8E1OPwQv2lqZMx5VAPV7ggQqaVjQam629NVODVUVNyMorQ7l
 uy3kbi3vAcazuvaApUchMDppfl919FP5QXFKaEm8HU3C8oROaKO6lZKc6OJFd1Bu
 eNLwg3FqI0JXRUqfggzyaqtpV8bMXzLVeQh98wlGbpkEF0yvXlTPProLJx4WX2kq
 /8OULi2k7g9QxOd8S9l3TdSHpOJKPzoDecvGW6WFM+0q5POs+Ybk69yU32irt/Fk
 2dNbqn8GgPXTkFMaBzlBFqq6Kgh4y1b6eQDjQC1oZGOyjK/HwtNteZHREEzg15A=
 =fg6j
 -----END PGP SIGNATURE-----

Merge tag 'drm-intel-fixes-2018-03-15' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

Only GVT fixes:
- Two warnings fix for runtime pm and usr copy (Xiong, Zhenyu)
- OA context fix for vGPU profiling (Min)
- privilege batch buffer reloc fix (Fred)

* tag 'drm-intel-fixes-2018-03-15' of git://anongit.freedesktop.org/drm/drm-intel:
  drm/i915/gvt: fix user copy warning by whitelist workload rb_tail field
  drm/i915/gvt: Correct the privilege shadow batch buffer address
  drm/i915/gvt: keep oa config in shadow ctx
  drm/i915/gvt: Add runtime_pm_get/put into gvt_switch_mmio
2018-03-16 12:51:35 +10:00
Dan Williams
dc9e0a9347 acpi, numa: fix pxm to online numa node associations
Commit 99759869fa "acpi: Add acpi_map_pxm_to_online_node()" added
support for mapping a given proximity to its nearest, by SLIT distance,
online node. However, it sometimes returns unexpected results due to the
fact that it switches from comparing the PXM node to the last node that
was closer than the current max.

    for_each_online_node(n) {
            dist = node_distance(node, n);
            if (dist < min_dist) {
                    min_dist = dist;
                    node = n;	<---- from this point we're using the
				      wrong node for node_distance()


Fixes: 99759869fa ("acpi: Add acpi_map_pxm_to_online_node()")
Cc: <stable@vger.kernel.org>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2018-03-15 19:49:14 -07:00
Leon Romanovsky
2975d5de64 RDMA/ucma: Check AF family prior resolving address
Garbage supplied by user will cause to UCMA module provide zero
memory size for memcpy(), because it wasn't checked, it will
produce unpredictable results in rdma_resolve_addr().

[   42.873814] BUG: KASAN: null-ptr-deref in rdma_resolve_addr+0xc8/0xfb0
[   42.874816] Write of size 28 at addr 00000000000000a0 by task resaddr/1044
[   42.876765]
[   42.876960] CPU: 1 PID: 1044 Comm: resaddr Not tainted 4.16.0-rc1-00057-gaa56a5293d7e #34
[   42.877840] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.0-0-g63451fca13-prebuilt.qemu-project.org 04/01/2014
[   42.879691] Call Trace:
[   42.880236]  dump_stack+0x5c/0x77
[   42.880664]  kasan_report+0x163/0x380
[   42.881354]  ? rdma_resolve_addr+0xc8/0xfb0
[   42.881864]  memcpy+0x34/0x50
[   42.882692]  rdma_resolve_addr+0xc8/0xfb0
[   42.883366]  ? deref_stack_reg+0x88/0xd0
[   42.883856]  ? vsnprintf+0x31a/0x770
[   42.884686]  ? rdma_bind_addr+0xc40/0xc40
[   42.885327]  ? num_to_str+0x130/0x130
[   42.885773]  ? deref_stack_reg+0x88/0xd0
[   42.886217]  ? __read_once_size_nocheck.constprop.6+0x10/0x10
[   42.887698]  ? unwind_get_return_address_ptr+0x50/0x50
[   42.888302]  ? replace_slot+0x147/0x170
[   42.889176]  ? delete_node+0x12c/0x340
[   42.890223]  ? __radix_tree_lookup+0xa9/0x160
[   42.891196]  ? ucma_resolve_ip+0xb7/0x110
[   42.891917]  ucma_resolve_ip+0xb7/0x110
[   42.893003]  ? ucma_resolve_addr+0x190/0x190
[   42.893531]  ? _copy_from_user+0x5e/0x90
[   42.894204]  ucma_write+0x174/0x1f0
[   42.895162]  ? ucma_resolve_route+0xf0/0xf0
[   42.896309]  ? dequeue_task_fair+0x67e/0xd90
[   42.897192]  ? put_prev_entity+0x7d/0x170
[   42.897870]  ? ring_buffer_record_is_on+0xd/0x20
[   42.898439]  ? tracing_record_taskinfo_skip+0x20/0x50
[   42.899686]  __vfs_write+0xc4/0x350
[   42.900142]  ? kernel_read+0xa0/0xa0
[   42.900602]  ? firmware_map_remove+0xdf/0xdf
[   42.901135]  ? do_task_dead+0x5d/0x60
[   42.901598]  ? do_exit+0xcc6/0x1220
[   42.902789]  ? __fget+0xa8/0xf0
[   42.903190]  vfs_write+0xf7/0x280
[   42.903600]  SyS_write+0xa1/0x120
[   42.904206]  ? SyS_read+0x120/0x120
[   42.905710]  ? compat_start_thread+0x60/0x60
[   42.906423]  ? SyS_read+0x120/0x120
[   42.908716]  do_syscall_64+0xeb/0x250
[   42.910760]  entry_SYSCALL_64_after_hwframe+0x21/0x86
[   42.912735] RIP: 0033:0x7f138b0afe99
[   42.914734] RSP: 002b:00007f138b799e98 EFLAGS: 00000287 ORIG_RAX: 0000000000000001
[   42.917134] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f138b0afe99
[   42.919487] RDX: 000000000000002e RSI: 0000000020000c40 RDI: 0000000000000004
[   42.922393] RBP: 00007f138b799ec0 R08: 00007f138b79a700 R09: 0000000000000000
[   42.925266] R10: 00007f138b79a700 R11: 0000000000000287 R12: 00007f138b799fc0
[   42.927570] R13: 0000000000000000 R14: 00007ffdbae757c0 R15: 00007f138b79a9c0
[   42.930047]
[   42.932681] Disabling lock debugging due to kernel taint
[   42.934795] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a0
[   42.936939] IP: memcpy_erms+0x6/0x10
[   42.938864] PGD 80000001bea92067 P4D 80000001bea92067 PUD 1bea96067 PMD 0
[   42.941576] Oops: 0002 [#1] SMP KASAN PTI
[   42.943952] CPU: 1 PID: 1044 Comm: resaddr Tainted: G    B 4.16.0-rc1-00057-gaa56a5293d7e #34
[   42.946964] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.0-0-g63451fca13-prebuilt.qemu-project.org 04/01/2014
[   42.952336] RIP: 0010:memcpy_erms+0x6/0x10
[   42.954707] RSP: 0018:ffff8801c8b479c8 EFLAGS: 00010286
[   42.957227] RAX: 00000000000000a0 RBX: ffff8801c8b47ba0 RCX: 000000000000001c
[   42.960543] RDX: 000000000000001c RSI: ffff8801c8b47bbc RDI: 00000000000000a0
[   42.963867] RBP: ffff8801c8b47b60 R08: 0000000000000000 R09: ffffed0039168ed1
[   42.967303] R10: 0000000000000001 R11: ffffed0039168ed0 R12: ffff8801c8b47bbc
[   42.970685] R13: 00000000000000a0 R14: 1ffff10039168f4a R15: 0000000000000000
[   42.973631] FS:  00007f138b79a700(0000) GS:ffff8801e5d00000(0000) knlGS:0000000000000000
[   42.976831] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   42.979239] CR2: 00000000000000a0 CR3: 00000001be908002 CR4: 00000000003606a0
[   42.982060] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   42.984877] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   42.988033] Call Trace:
[   42.990487]  rdma_resolve_addr+0xc8/0xfb0
[   42.993202]  ? deref_stack_reg+0x88/0xd0
[   42.996055]  ? vsnprintf+0x31a/0x770
[   42.998707]  ? rdma_bind_addr+0xc40/0xc40
[   43.000985]  ? num_to_str+0x130/0x130
[   43.003410]  ? deref_stack_reg+0x88/0xd0
[   43.006302]  ? __read_once_size_nocheck.constprop.6+0x10/0x10
[   43.008780]  ? unwind_get_return_address_ptr+0x50/0x50
[   43.011178]  ? replace_slot+0x147/0x170
[   43.013517]  ? delete_node+0x12c/0x340
[   43.016019]  ? __radix_tree_lookup+0xa9/0x160
[   43.018755]  ? ucma_resolve_ip+0xb7/0x110
[   43.021270]  ucma_resolve_ip+0xb7/0x110
[   43.023968]  ? ucma_resolve_addr+0x190/0x190
[   43.026312]  ? _copy_from_user+0x5e/0x90
[   43.029384]  ucma_write+0x174/0x1f0
[   43.031861]  ? ucma_resolve_route+0xf0/0xf0
[   43.034782]  ? dequeue_task_fair+0x67e/0xd90
[   43.037483]  ? put_prev_entity+0x7d/0x170
[   43.040215]  ? ring_buffer_record_is_on+0xd/0x20
[   43.042990]  ? tracing_record_taskinfo_skip+0x20/0x50
[   43.045595]  __vfs_write+0xc4/0x350
[   43.048624]  ? kernel_read+0xa0/0xa0
[   43.051604]  ? firmware_map_remove+0xdf/0xdf
[   43.055379]  ? do_task_dead+0x5d/0x60
[   43.058000]  ? do_exit+0xcc6/0x1220
[   43.060783]  ? __fget+0xa8/0xf0
[   43.063133]  vfs_write+0xf7/0x280
[   43.065677]  SyS_write+0xa1/0x120
[   43.068647]  ? SyS_read+0x120/0x120
[   43.071179]  ? compat_start_thread+0x60/0x60
[   43.074025]  ? SyS_read+0x120/0x120
[   43.076705]  do_syscall_64+0xeb/0x250
[   43.079006]  entry_SYSCALL_64_after_hwframe+0x21/0x86
[   43.081606] RIP: 0033:0x7f138b0afe99
[   43.083679] RSP: 002b:00007f138b799e98 EFLAGS: 00000287 ORIG_RAX: 0000000000000001
[   43.086802] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f138b0afe99
[   43.089989] RDX: 000000000000002e RSI: 0000000020000c40 RDI: 0000000000000004
[   43.092866] RBP: 00007f138b799ec0 R08: 00007f138b79a700 R09: 0000000000000000
[   43.096233] R10: 00007f138b79a700 R11: 0000000000000287 R12: 00007f138b799fc0
[   43.098913] R13: 0000000000000000 R14: 00007ffdbae757c0 R15: 00007f138b79a9c0
[   43.101809] Code: 90 90 90 90 90 eb 1e 0f 1f 00 48 89 f8 48 89 d1 48
c1 e9 03 83 e2 07 f3 48 a5 89 d1 f3 a4 c3 66 0f 1f 44 00 00 48 89 f8 48
89 d1 <f3> a4 c3 0f 1f 80 00 00 00 00 48 89 f8 48 83 fa 20 72 7e 40 38
[   43.107950] RIP: memcpy_erms+0x6/0x10 RSP: ffff8801c8b479c8

Reported-by: <syzbot+1d8c43206853b369d00c@syzkaller.appspotmail.com>
Fixes: 7521663857 ("RDMA/cma: Export rdma cm interface to userspace")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2018-03-15 20:12:38 -06:00
Dave Airlie
d4487b57a4 Merge branch 'linux-4.16' of git://github.com/skeggsb/linux into drm-fixes
nouveau regression fixes.

* 'linux-4.16' of git://github.com/skeggsb/linux:
  drm/nouveau/bl: fix backlight regression
  drm/nouveau/bl: Fix oops on driver unbind
  drm/nouveau/mmu: ALIGN_DOWN correct variable
2018-03-16 12:06:17 +10:00
Linus Torvalds
df09348f78 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:

 - backport-friendly part of lock_parent() race fix

 - a fix for an assumption in the heurisic used by path_connected() that
   is not true on NFS

 - livelock fixes for d_alloc_parallel()

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: Teach path_connected to handle nfs filesystems with multiple roots.
  fs: dcache: Use READ_ONCE when accessing i_dir_seq
  fs: dcache: Avoid livelock between d_alloc_parallel and __d_add
  lock_parent() needs to recheck if dentry got __dentry_kill'ed under it
2018-03-15 18:57:14 -07:00