Currently exclusive TCON clock lock is never released, which, for
example, prevents changing resolution on HDMI.
In order to fix that, release clock when disabling TCON. TCON is always
disabled first before new mode is set.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180301213442.16677-7-jernej.skrabec@siol.net
It should be good that no use "_" is in examples. Consequently,
those nodes in certain files which have an inappropriate name containing
"_" are all being replaced with "-".
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-gpio@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CLK_PLL_VIDEO needs to be referenced in HDMI DT entry as a possible
PHY clock parent.
Export it so it can be used later in DT.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some units have to be able to set it's own clock precisely to work
correctly. Allow them to do so by adding CLK_SET_RATE_PARENT flag.
Add this flag to DE, TCON and HDMI clocks.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Although user manuals for H3 and H5 SoCs state that minimal rate
supported by video PLL is around 30 MHz, it seems that in reality
minimal rate is around 192 MHz.
Experiments showed that any rate below 96 MHz doesn't produce any video
output at all. Even at this frequency, stable output depends on right
factors. For example, when N = 4 and M = 1, output is stable and when N
= 8 and M = 2, it's not.
BSP clock driver suggest that minimum stable frequency is 192 MHz. That
would also be in line with A64 SoC, which has similar periphery.
Set minimal video PLL rate for H3/H5 to 192 MHz.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some NM PLLs doesn't work well when their output clock rate is set below
certain rate.
Add support for that constrain.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add group configuration for uarts that are cut down
variants, the standard being full, i.e. all signals,
flow control, i.e. rx/tx and cts/rts, and rx/tx only.
This allows us to be more precise in which pins we're
actually using.
Unfortunately the existing naming scheme leaves things
to be desired, e.g. uart3grp0 means RX/TX and CTS/RTS,
yet uart0grp0 means all pins.
Since the exising suffixes have different meaning for
different uarts, and the fact that we cannot change
the name of existing groups, makes it hard to use a
descriptive name for the newly added groups.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add missing pin group uart5nocts (all pins except cts), which has been
supported by the artpec6 pinctrl driver since its initial submission.
Fixes: 00df0582ea ("pinctrl: Add pincontrol driver for ARTPEC-6 SoC")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit c301b327ae.
While this works splendidly on rk3399-gru devices using the cros-ec
extcon, other rk3399-based devices using the fusb302 or no power-delivery
controller at all don't probe at all anymore, as the typec-phy currently
always expects the extcon to be available and therefore defers probing
indefinitly on these.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The current code for initializing the VRMA (virtual real memory area)
for HPT guests requires the page size of the backing memory to be one
of 4kB, 64kB or 16MB. With a radix host we have the possibility that
the backing memory page size can be 2MB or 1GB. In these cases, if the
guest switches to HPT mode, KVM will not initialize the VRMA and the
guest will fail to run.
In fact it is not necessary that the VRMA page size is the same as the
backing memory page size; any VRMA page size less than or equal to the
backing memory page size is acceptable. Therefore we now choose the
largest page size out of the set {4k, 64k, 16M} which is not larger
than the backing memory page size.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This fixes several bugs in the radix page fault handler relating to
the way large pages in the memory backing the guest were handled.
First, the check for large pages only checked for explicit huge pages
and missed transparent huge pages. Then the check that the addresses
(host virtual vs. guest physical) had appropriate alignment was
wrong, meaning that the code never put a large page in the partition
scoped radix tree; it was always demoted to a small page.
Fixing this exposed bugs in kvmppc_create_pte(). We were never
invalidating a 2MB PTE, which meant that if a page was initially
faulted in without write permission and the guest then attempted
to store to it, we would never update the PTE to have write permission.
If we find a valid 2MB PTE in the PMD, we need to clear it and
do a TLB invalidation before installing either the new 2MB PTE or
a pointer to a page table page.
This also corrects an assumption that get_user_pages_fast would set
the _PAGE_DIRTY bit if we are writing, which is not true. Instead we
mark the page dirty explicitly with set_page_dirty_lock(). This
also means we don't need the dirty bit set on the host PTE when
providing write access on a read fault.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Eric Dumazet says:
====================
tcp_bbr: more GSO work
Playing with r8152 USB 1Gbit NIC, on both USB2 and USB3 slots, I found
that BBR was performing poorly, because of TSO being limited to 16KB
This patch series makes sure BBR is not under estimating number of
packets that are needed to fill the pipe when a device has suboptimal
TSO limits.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Its value is computed then immediately used,
there is no need to store it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is second part of dealing with suboptimal device gso parameters.
In first patch (350c9f484b "tcp_bbr: better deal with suboptimal GSO")
we dealt with devices having low gso_max_segs
Some devices lower gso_max_size from 64KB to 16 KB (r8152 is an example)
In order to probe an optimal cwnd, we want BBR being not sensitive
to whatever GSO constraint a device can have.
This patch removes tso_segs_goal() CC callback in favor of
min_tso_segs() for CC wanting to override sysctl_tcp_min_tso_segs
Next patch will remove bbr->tso_segs_goal since it does not have
to be persistent.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-02-28
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Add schedule points and reduce the number of loop iterations
the test_bpf kernel module is performing in order to not hog
the CPU for too long, from Eric.
2) Fix an out of bounds access in tail calls in the ppc64 BPF
JIT compiler, from Daniel.
3) Fix a crash on arm64 on unaligned BPF xadd operations that
could be triggered via interpreter and JIT, from Daniel.
Please not that once you merge net into net-next at some point, there
is a minor merge conflict in test_verifier.c since test cases had
been added at the end in both trees. Resolution is trivial: keep all
the test cases from both trees.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If ethtool_ops->get_fecparam returns an error, pass that error on to the
user, rather than ignoring it.
Fixes: 1a5f3da20b ("net: ethtool: add support for forward error correction modes")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ip_error() is called the device is the l3mdev master instead of the
original device. So the forwarding check should be on the original one.
Changes from v2:
- Handle the original device disappearing (per David Ahern)
- Minimize the change in code order
Changes from v1:
- Only need to reset the device on which __in_dev_get_rcu() is done (per
David Ahern).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
Jiong says:
This patch set is an application of CFG information on eBPF program
visualization. It presents some initial code for building CFG information
from eBPF instruction sequences.
After we get eBPF program bytecode, we do sub-program detection and
basic-block partition. These information then are visualized into DOT
graph.
The user could use any DOT graphic tools (xdot, graphviz etc) to view it.
For example:
bpftool prog dump xlated id 2 visual &>output.dot
[xdot | dotty] output.dot
dot -Tpng -o output.png
This initial patch set hasn't tuned much on the dot description layout
nor decoration, we could improve them later once the direction of the patch
set is agreed on. We could also visualize some static analysis performance
data.
v2 (Jakub):
- update license headers and add SPDX tags.
====================
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add bash completion for the "visual" keyword used for dumping the CFG of
eBPF programs with bpftool. Make sure we only complete with this keyword
when we dump "xlated" (and not "jited") instructions.
Acked-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch adds new command-line option for visualizing the xlated eBPF
sequence.
Documentations are updated accordingly.
Usage:
bpftool prog dump xlated id 2 visual
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch let bpftool print .dot graph file into stdout.
This graph is generated by the following steps:
- iterate through the function list.
- generate basic-block(BB) definition for each BB in the function.
- draw out edges to connect BBs.
This patch is the initial support, the layout and decoration of the .dot
graph could be improved.
Also, it will be useful if we could visualize some performance data from
static analysis.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch adds out edges for each basic-block. We will need these out
edges to finish the .dot graph drawing.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch partition basic-block for each function in the CFG. The
algorithm is simple, we identify basic-block head in a first traversal,
then second traversal to identify the tail.
We could build extended basic-block (EBB) in next steps. EBB could make the
graph more readable when the eBPF sequence is big.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch detect all sub-programs from the eBPF sequence and keep the
information in the new CFG data structure.
The detection algorithm is basically the same as the one in verifier except
we need to use insn->off instead of insn->imm to get the pc-relative call
offset. Because verifier has modified insn->off/insn->imm during finishing
the verification.
Also, we don't need to do some sanity checks as verifier has done them.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch factors out those code of dumping xlated eBPF instructions into
xlated_dumper.[h|c].
They are quite independent dumper functions, so better to be kept
separately.
New dumper support will be added in later patches in this set.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
It is obvious we could use 'else if' instead of start a new 'if' in the
touched code.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
recvmmsg does not call ___sys_recvmsg when sk_err is set.
That is fine for normal reads but, for MSG_ERRQUEUE, recvmmsg
should always call ___sys_recvmsg regardless of sk->sk_err to
be able to clear error queue. Otherwise, users are not able to
drain the error queue using recvmmsg.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a file for documenting SCSI sd module parameters and describe the
cache_type setting.
[mkp: tweaked text a bit]
Signed-off-by: Weiping Zhang <zhangweiping@didichuxing.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Setting an interface into a VRF fails with 'RTNETLINK answers: File
exists' if one of its VLAN interfaces is already in the same VRF.
As the VRF is an upper device of the VLAN interface, it is also showing
up as an upper device of the interface itself. The solution is to
restrict this check to devices other than master. As only one master
device can be linked to a device, the check in this case is that the
upper device (VRF) being linked to is not the same as the master device
instead of it not being any one of the upper devices.
The following example shows an interface ens12 (with a VLAN interface
ens12.10) being set into VRF green, which behaves as expected:
# ip link add link ens12 ens12.10 type vlan id 10
# ip link set dev ens12 master vrfgreen
# ip link show dev ens12
3: ens12: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel
master vrfgreen state UP mode DEFAULT group default qlen 1000
link/ether 52:54:00:4c:a0:45 brd ff:ff:ff:ff:ff:ff
But if the VLAN interface has previously been set into the same VRF,
then setting the interface into the VRF fails:
# ip link set dev ens12 nomaster
# ip link set dev ens12.10 master vrfgreen
# ip link show dev ens12.10
39: ens12.10@ens12: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
qdisc noqueue master vrfgreen state UP mode DEFAULT group default
qlen 1000 link/ether 52:54:00:4c:a0:45 brd ff:ff:ff:ff:ff:ff
# ip link set dev ens12 master vrfgreen
RTNETLINK answers: File exists
The workaround is to move the VLAN interface back into the default VRF
beforehand, but it has to be shut first so as to avoid the risk of
traffic leaking from the VRF. This fix avoids needing this workaround.
Signed-off-by: Mike Manning <mmanning@att.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: phy: Reduce duplication
This patch series reduces the duplication among 10G PHY drivers that just
essentially stub most functions, but do that while replicating what the existing
generic functions do.
Changes in v3:
- removed unused "reg" variable in teranetics.c
- fixed subject for patch 5 since we actually use gen10g_no_soft_reset()
Changes in v2:
- rename gen10g_soft_reset() to gen10g_no_soft_reset() to better illustrate
what it does (or does not)
- removed stray comment in marvell10g.c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cortina_soft_reset() does the same thing as gen10g_soft_reset(), and
cortina_config_aneg() is actually doing what gen10g_config_init() does
for 10G capable PHYs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update teranetics_aneg_done() to use genphy_c45_aneg_done() instead of
duplicating that code, and switch to gen10g_* functions where
appropriate instead of maintaining identical copies doing nothing.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In order to remove a fair amount of duplication in the different 10G PHY
drivers, export all gen10g_* functions to be able to make use of those.
While we are at it, rename gen10g_soft_reset() to gen10g_no_soft_reset()
to illustrate what it does.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Finn Thain says:
====================
Fixes, cleanup and modernization for mac89x0 driver
Changes since v4 of combined patch series:
- Removed redundant and non-portable MACH_IS_MAC tests.
- Added acked-by tags from Geert Uytterhoeven.
- Omitted patches unrelated to mac89x0 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adopt the conventional style of debug logging because it is both
shorter and more flexible.
Remove the 'version_printed' flag as the version will be printed
only once anyway (when the module loads).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix log message fragments that no longer produce the desired output
since the behaviour of printk() was changed.
Add missing printk severity levels.
Drop deprecated "out of memory" message as per checkpatch advice.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently these Dayna cards don't have a pseudoslot declaration ROM
which means they can't be probed like NuBus cards.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
selftests: forwarding: misc bug fixes and enhancements
Bug fixes and an enhancement for the recent forwarding tests:
- only check tc version on tc tests
- handle multipath tests failing with 0 packet count
- fix ping command for IPv6 on Debian jessie
- improve summary of multipath tests
v2
- add CHECK_TC to bridge_vlan_aware.sh (Ido)
- dropped patch 2; always check for mz given its use
- fixed commit message for the last patch (Multipath: was dropped)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a better description to the summary for multipath tests. e.g.,
INFO: Running IPv6 multipath tests
TEST: ECMP [PASS]
INFO: Expected ratio 1.00 Measured ratio 1.02
TEST: Weighted MP 2:1 [PASS]
INFO: Expected ratio 2.00 Measured ratio 2.02
TEST: Weighted MP 11:45 [PASS]
INFO: Expected ratio 4.09 Measured ratio 4.03
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Debian jessie ping can not handle IPv6 addresses so the command
fails. Use PING6 which is set to ping6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the packet stats have a difference of 0, the test output shows:
INFO: Expected ratio 2.00 Measured ratio
Runtime error (func=(main), adr=9): Divide by zero
(standard_in) 2: syntax error
(standard_in) 1: syntax error
./router_multipath.sh: line 187: test: : integer expression expected
TEST: Multipath [FAIL]
Too large discrepancy between expected and measured ratios
Handle the 0 and display a cleaner message:
INFO: Running IPv6 multipath tests
TEST: Multipath [FAIL]
Packet difference is 0
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Capabilities of tc command are irrelevant for router tests:
$ ./router.sh
SKIP: iproute2 too old, missing shared block support
Add a CHECK_TC flag and only check tc capabilities if set. Add flag to
tc_common.sh and have it sourced before lib.sh
Also, if the command lacks some feature the test should exit non-0.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: bfff486265 ("net: fib_rules: support for match on ip_proto, sport and dport")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64 bit CPUs there is a memory corruption bug on probe(). It should
be a u32 pointer instead of an unsigned long pointer or we write past
the end of the setupdata[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the byte order of the SGPIO api and brings it back in
sync with ledmon v0.80 and above.
[mkp: added missing SoB and fixed whitespace]
Signed-off-by: Wilfried Weissmann <wilfried.weissmann@gmx.at>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>