Commit graph

752,023 commits

Author SHA1 Message Date
Andreas Gruenbacher
fffb64127a gfs2: Zero out fallocated blocks in fallocate_chunk
Instead of zeroing out fallocated blocks in gfs2_iomap_alloc, zero them
out in fallocate_chunk, much higher up the call stack.  This gets rid of
gfs2's abuse of the IOMAP_ZERO flag as well as the gfs2 specific zeronew
buffer flag.  I can't think of a reason why zeroing out the blocks in
gfs2_iomap_alloc would have any benefits: there is no additional locking
at that level that would add protection to the newly allocated blocks.

While at it, change fallocate over from gs2_block_map to gfs2_iomap_begin.

Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
2018-03-29 06:50:32 -07:00
Richard Zhu
027fa4dee9 ahci: imx: add the imx8qm ahci sata support
- There are three PHY lanes on iMX8QM, and can be
  used in the following three cases
    1. a two lanes PCIE_A, and a single lane SATA.
    2. a single lane PCIE_A, a single lane PCIE_B
    and a single lane SATA.
    3. a two lanes PCIE_A, and a single lane PCIE_B.
  The configuration of the iMX8QM AHCI SATA is relied
  on the usage of PCIE ports in the case 1 and 2.
  Use standalone iMX8 AHCI SATA probe and enable
  functions to enable iMX8QM AHCI SATA support.
- To save power consumption, PHY CLKs can be gated
  off after the configurations are done.
- The impedance ratio should be configured refer to
  differnet REXT values.
  0x6c <--> REXT value is 85Ohms
  0x80 (default value) <--> REXT value is 100Ohms.
  In general, REXT value should be 85ohms in standalone
  PCIE HW board design, and 100ohms in SATA standalone
  HW board design.
  When the PCIE and the SATA are enabled simultaneously
  in the HW board design. The REXT value would be set
  to 85ohms.
  Configure the SATA PHY impedance ratio to 0x6c in
  default.

Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2018-03-29 06:43:55 -07:00
Joerg Roedel
d4f96fd5c2 Merge branches 'x86/amd', 'x86/vt-d', 'arm/rockchip', 'arm/omap', 'arm/mediatek', 'arm/exynos', 'arm/renesas', 'arm/smmu' and 'core' into next 2018-03-29 15:24:40 +02:00
Robin Murphy
7868805969 iommu/io-pgtable-arm: Avoid warning with 32-bit phys_addr_t
It's not entirely unreasonable for io-pgtable-arm to be built for
configurations with 32-bit phys_addr_t, where the compiler rightly
raises a warning about the 36-bit shift. That particular code path
should never actually *run* on those systems, but we still want it
to compile cleanly, which is easily done by using an unambiguous u64
as the intermediate type instead.

Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 15:19:10 +02:00
Emmanuel Grumbach
c470bdc1aa mac80211: don't WARN on bad WMM parameters from buggy APs
Apparently, some APs are buggy enough to send a zeroed
WMM IE. Don't WARN on this since this is not caused by a bug
on the client's system.

This aligns the condition of the WARNING in drv_conf_tx
with the validity check in ieee80211_sta_wmm_params.
We will now pick the default values whenever we get
a zeroed WMM IE.

This has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=199161

Fixes: f409079bb6 ("mac80211: sanity check CW_min/CW_max towards driver")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29 15:02:38 +02:00
Kalle Valo
14c99949a3 Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git
ath.git patches for 4.17. Major changes:

ath10k

* enable chip temperature measurement for QCA6174/QCA9377

* add firmware memory dump for QCA9984

* enable buffer STA on TDLS link for QCA6174

* support different beacon internals in multiple interface scenario
  for QCA988X/QCA99X0/QCA9984/QCA4019
2018-03-29 15:55:28 +03:00
Tetsuo Handa
b3c39758c8 lockdep: Make the lock debug output more useful
The lock debug output in print_lock() has a few shortcomings:

 - It prints the hlock->acquire_ip field in %px and %pS format. That's
   redundant information.

 - It lacks information about the lock object itself. The lock class is
   not helpful to identify a particular instance of a lock.

Change the output so it prints:

 - hlock->instance to allow identification of a particular lock instance.

 - only the %pS format of hlock->ip_acquire which is sufficient to decode
   the actual code line with faddr2line.

The resulting output is:

3 locks held by a.out/31106:
#0: 00000000b0f753ba (&mm->mmap_sem){++++}, at: copy_process.part.41+0x10d5/0x1fe0
#1: 00000000ef64d539 (&mm->mmap_sem/1){+.+.}, at: copy_process.part.41+0x10fe/0x1fe0
#2: 00000000b41a282e (&mapping->i_mmap_rwsem){++++}, at: copy_process.part.41+0x12f2/0x1fe0

[ tglx: Massaged changelog ]

Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: linux-mm@kvack.org
Cc: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/201803271941.GBE57310.tVSOJLQOFFOHFM@I-love.SAKURA.ne.jp
2018-03-29 14:41:40 +02:00
Greg Kroah-Hartman
86f690e8bf stm class/intel_th: Updates for 4.17
These are:
   * Mass conversion to GPL-2 SPDX header
   * Moved "hwtracing" to now its own submenu, to uncrowd the parent menu a bit
   * Added MAINTAINERS entry for drivers/hwtracing
   * Somewhat small Trace Hub fixes
   * Added ACPI glue layer for the Trace Hub
   * Added more module parameters to dummy_stm for better test coverage
 -----BEGIN PGP SIGNATURE-----
 
 iJkEABEIAEEWIQQSviFCoXpKPDNATbnrxfYkYwVX/wUCWrzG7yMcYWxleGFuZGVy
 LnNoaXNoa2luQGxpbnV4LmludGVsLmNvbQAKCRDrxfYkYwVX/0jcAQCE/maw6L5P
 NdT3Ck3EuDWzij9uimq3Y0UyI9F4Cd+vYgD+N8Skyiua+NqfBGB0oXNsJt2acirg
 O3G990RK9dX4H2c=
 =CuGw
 -----END PGP SIGNATURE-----

Merge tag 'stm-intel_th-for-greg-20180329' of git://git.kernel.org/pub/scm/linux/kernel/git/ash/stm into char-misc-next

Alexander writes:

stm class/intel_th: Updates for 4.17

These are:
  * Mass conversion to GPL-2 SPDX header
  * Moved "hwtracing" to now its own submenu, to uncrowd the parent menu a bit
  * Added MAINTAINERS entry for drivers/hwtracing
  * Somewhat small Trace Hub fixes
  * Added ACPI glue layer for the Trace Hub
  * Added more module parameters to dummy_stm for better test coverage
2018-03-29 14:15:13 +02:00
Johannes Berg
1dd2eefb8e Merge branch 'eapol-over-nl80211' into mac80211-next
This is the EAPoL over nl80211 patchset from Denis Kenzior, minus some
infrastructure patches I'd split out and applied earlier. Denis described
it as follows:

This patchset adds support for running 802.11 authentication mechanisms (e.g.
802.1X, 4-Way Handshake, etc) over NL80211 instead of putting them onto the
network device.  This has the advantage of fixing several long-standing race
conditions that result from userspace operating on multiple transports in order
to manage a 802.11 connection (e.g. NL80211 and wireless netdev, wlan0, etc).

For example, userspace would sometimes see 4-Way handshake packets before
NL80211 signaled that the connection has been established.  Leading to ugly
hacks or having the STA wait for retransmissions from the AP.

This also provides a way to mitigate a particularly nasty race condition where
the encryption key could be set prior to the 4-way handshake packet 4/4 being
sent.  This would result in the packet being sent encrypted and discarded by
the peer.  The mitigation strategy for this race is for userspace to explicitly
tell the kernel that a particular EAPoL packet should not be encrypted.

To make this possible this patchset introduces a new NL80211 command and several
new attributes.  A userspace that is capable of processing EAPoL packets over
NL80211 includes a new NL80211_ATTR_CONTROL_PORT_OVER_NL80211 attribute in its
NL80211_CMD_ASSOCIATE or NL80211_CMD_CONNECT requests being sent to the kernel.
The previously added NL80211_ATTR_SOCKET_OWNER attribute must also be included.
The latter is used by the kernel to send NL80211_CMD_CONTROL_PORT_FRAME
notifications back to userspace via a netlink unicast.  If the
NL80211_ATTR_CONTROL_PORT_OVER_NL80211 attribute is not specified, then legacy
behavior is kept and control port packets continue to flow over the network
interface.

If control port over nl80211 transport is requested, then control port packets
are intercepted just prior to being handed to the network device and sent over
netlink via the NL80211_CMD_CONTROL_PORT_FRAME notification.
NL80211_ATTR_CONTROL_PORT_ETHERTYPE and NL80211_ATTR_MAC are included to
specify the control port frame protocol and source address respectively.  If
the control port frame was received unencrypted then
NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT flag is also included.  NL80211_ATTR_FRAME
attribute contains the raw control port frame with all transport layer headers
stripped (e.g. this would be the raw EAPoL frame).

Userspace can reply to control port frames either via legacy methods (by sending
frames to the network device) or via NL80211_CMD_CONTROL_PORT_FRAME request.
Userspace would included NL80211_ATTR_FRAME with the raw control port frame as
well as NL80211_Attr_MAC and NL80211_ATTR_CONTROL_PORT_ETHERTYPE attributes to
specify the destination address and protocol respectively.  This allows
Pre-Authentication (protocol 0x88c7) frames to be sent via this mechanism as
well.  Finally, NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT flag can be included to
tell the driver to send the frame unencrypted, e.g. for 4-Way handshake 4/4
frames.

The proposed patchset has been tested in a mac80211_hwsim based environment with
hostapd and iwd.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29 14:09:28 +02:00
Denis Kenzior
018f6fbf54 mac80211: Send control port frames over nl80211
If userspace requested control port frames to go over 80211, then do so.
The control packets are intercepted just prior to delivery of the packet
to the underlying network device.

Pre-authentication type frames (protocol: 0x88c7) are also forwarded
over nl80211.

Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29 14:08:30 +02:00
Denis Kenzior
9118064914 mac80211: Add support for tx_control_port
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29 14:01:27 +02:00
Denis Kenzior
1224f5831a nl80211: Add control_port_over_nl80211 to mesh_setup
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29 14:01:27 +02:00
Denis Kenzior
c3bfe1f6fc nl80211: Add control_port_over_nl80211 for ibss
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29 14:00:27 +02:00
Denis Kenzior
64bf3d4bc2 nl80211: Add CONTROL_PORT_OVER_NL80211 attribute
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29 13:45:04 +02:00
Denis Kenzior
2576a9ace4 nl80211: Implement TX of control port frames
This commit implements the TX side of NL80211_CMD_CONTROL_PORT_FRAME.
Userspace provides the raw EAPoL frame using NL80211_ATTR_FRAME.
Userspace should also provide the destination address and the protocol
type to use when sending the frame.  This is used to implement TX of
Pre-authentication frames.  If CONTROL_PORT_ETHERTYPE_NO_ENCRYPT is
specified, then the driver will be asked not to encrypt the outgoing
frame.

A new EXT_FEATURE flag is introduced so that nl80211 code can check
whether a given wiphy has capability to pass EAPoL frames over nl80211.

Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29 13:44:19 +02:00
Denis Kenzior
6a671a50f8 nl80211: Add CMD_CONTROL_PORT_FRAME API
This commit also adds cfg80211_rx_control_port function.  This is used
to generate a CMD_CONTROL_PORT_FRAME event out to userspace.  The
conn_owner_nlportid is used as the unicast destination.  This means that
userspace must specify NL80211_ATTR_SOCKET_OWNER flag if control port
over nl80211 routing is requested in NL80211_CMD_CONNECT,
NL80211_CMD_ASSOCIATE, NL80211_CMD_START_AP or IBSS/mesh join.

Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix return value of cfg80211_rx_control_port()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29 13:44:04 +02:00
Thomas Gleixner
71e6882b0a irqchip updates for 4.17
- New Qualcomm PDC irqchip
 - New Microsemi Ocelot irqchip
 - Suspend/resume support for some oddball GICv3 irqchip
 - Better GIC/GICv3 support for kexec
 - Various cleanups and fixes
 -----BEGIN PGP SIGNATURE-----
 
 iQJJBAABCAAzFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAlq8xbMVHG1hcmMuenlu
 Z2llckBhcm0uY29tAAoJECPQ0LrRPXpDHlYQAKBxb1i3pZ9rmiuQPdrP8b2Yqalg
 M98ojKVGkX3gjsPQVEbeDW8r+/JShNJWzf7J885N0FDJ61+MAOJaA9Zgs9QkZiDp
 l2iNiiIYa9yFe1u/5vg5PEyIfw7HzzXSqW2EKpFqq2SoeGiX+cQGIdR+dmWADQgV
 VACM72aki0ERiZOdBrUy0sADYkL7qEUmeADjSYvSnqluIr10TWmKY11UGtTQI9gx
 aE2AZm+vcYsAeRndFybDAeZ02DT47nFgOETqss1OhO8Z99rrcRI98nyowYCWQGRH
 unRSPJxwaRF99/IFD+/zNGf9+C8eNTznqL1f/Qw7/I+3vAx0E4IcwN0H/y/9ylpg
 9OsKjJTO9GXy8PqPQnLWdeoS2YAVVWn8PppvhgNmIt9K7cAbie1ump5tBWRId9ZE
 G/YjLz0wnPXxbP6YoLm+YrOxvBH37zPihqZSm+hsNSV1IpZkn1e3QsJqxuTOdJyp
 OrEJKbDQxc9i5dZJQh5urhjEhFR6PQp9KqWcbzg1vrFgmGvbniE4r/ReH0aQHljx
 wDNGMuSS80xJNmKAs7rKW5HNoWb1963LIa2z27Sk94lQeFHsLxpOWMf/2mCSVZkv
 BgkZ0CfROcIdxXNcJaz6LlGVqdO/oIjdDGC5TWL+2yS3puatonjcduYYZEjB6gbv
 IETl4aD8E/tvpsxf
 =Zqil
 -----END PGP SIGNATURE-----

Merge tag 'irqchip-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core

Pull irqchip updates for 4.17 from Marc Zyngier:

 - New Qualcomm PDC irqchip
 - New Microsemi Ocelot irqchip
 - Suspend/resume support for some oddball GICv3 irqchip
 - Better GIC/GICv3 support for kexec
 - Various cleanups and fixes
2018-03-29 13:21:29 +02:00
Rafael J. Wysocki
4dc2375c1a cpuidle: poll_state: Avoid invoking local_clock() too often
Rik reports that he sees an increase in CPU use in one benchmark
due to commit 612f1a22f067 "cpuidle: poll_state: Add time limit to
poll_idle()" that caused poll_idle() to call local_clock() in every
iteration of the loop.  Utilization increase generally means more
non-idle time with respect to total CPU time (on the average) which
implies reduced CPU frequency.

Doug reports that limiting the rate of local_clock() invocations
in there causes much less power to be drawn during a CPU-intensive
parallel workload (with idle states 1 and 2 disabled to enforce more
state 0 residency).

These two reports together suggest that executing local_clock() on
multiple CPUs in parallel at a high rate may cause chips to get hot
and trigger thermal/power limits on them to kick in, so reduce the
rate of local_clock() invocations in poll_idle() to avoid that issue.

Fixes: 612f1a22f067 "cpuidle: poll_state: Add time limit to poll_idle()"
Reported-by: Rik van Riel <riel@surriel.com>
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Rik van Riel <riel@surriel.com>
Reviewed-by: Rik van Riel <riel@surriel.com>
2018-03-29 13:06:08 +02:00
Rafael J. Wysocki
64bdff6980 PM: cpuidle/suspend: Add s2idle usage and time state attributes
Add a new attribute group called "s2idle" under the sysfs directory
of each cpuidle state that supports the ->enter_s2idle callback
and put two new attributes, "usage" and "time", into that group to
represent the number of times the given state was requested for
suspend-to-idle and the total time spent in suspend-to-idle after
requesting that state, respectively.

That will allow diagnostic information related to suspend-to-idle
to be collected without enabling advanced debug features and
analyzing dmesg output.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-03-29 13:06:08 +02:00
Marek Szyprowski
8919d779f1 cpuidle: Enable coupled cpuidle support on Exynos3250 platform
All the needed code has been already merged to mach-exynos core in
commit af9971144d ("ARM: EXYNOS: add coupled cpuidle support for
Exynos3250"), so enable support for coupled variant also for Exynos3250
SoCs.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-03-29 13:06:08 +02:00
Rafael J. Wysocki
a37b969a61 cpuidle: poll_state: Add time limit to poll_idle()
If poll_idle() is allowed to spin until need_resched() returns 'true',
it may actually spin for a much longer time than expected by the idle
governor, since set_tsk_need_resched() is not always called by the
timer interrupt handler.  If that happens, the CPU may spend much
more time than anticipated in the "polling" state.

To prevent that from happening, limit the time of the spinning loop
in poll_idle().

Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
2018-03-29 13:06:07 +02:00
Aniruddha Banerjee
aa08192a25 irqchip/gic: Take lock when updating irq type
Most MMIO GIC register accesses use a 1-hot bit scheme that
avoids requiring any form of locking. This isn't true for the
GICD_ICFGRn registers, which require a RMW sequence.

Unfortunately, we seem to be missing a lock for these particular
accesses, which could result in a race condition if changing the
trigger type on any two interrupts within the same set of 16
interrupts (and thus controlled by the same CFGR register).

Introduce a private lock in the GIC common comde for this
particular case, making it cover both GIC implementations
in one go.

Cc: stable@vger.kernel.org
Signed-off-by: Aniruddha Banerjee <aniruddhab@nvidia.com>
[maz: updated changelog]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2018-03-29 11:47:50 +01:00
Randy Dunlap
72ef0f24d5 hwtracing: Add HW tracing support menu
Make a "HW tracing support" menu and move 2 entries into it.
(No change in Coresight, which is ARM-specific and is only listed for
ARM & ARM64.)

This makes the Device Drivers menu more consistent and prevents these
drivers from being listed at the top level of the Device Drivers menu.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
2018-03-29 13:38:10 +03:00
Jeffy Chen
57c26957bd iommu/rockchip: Support sharing IOMMU between masters
There would be some masters sharing the same IOMMU device. Put them in
the same iommu group and share the same iommu domain.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:29 +02:00
Jeffy Chen
0f181d3cf7 iommu/rockchip: Add runtime PM support
When the power domain is powered off, the IOMMU cannot be accessed and
register programming must be deferred until the power domain becomes
enabled.

Add runtime PM support, and use runtime PM device link from IOMMU to
master to enable and disable IOMMU.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:28 +02:00
Jeffy Chen
4d88a8a4c3 iommu/rockchip: Fix error handling in init
It's hard to undo bus_set_iommu() in the error path, so move it to the
end of rk_iommu_probe().

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:28 +02:00
Jeffy Chen
5fd577c3ea iommu/rockchip: Use OF_IOMMU to attach devices automatically
Converts the rockchip-iommu driver to use the OF_IOMMU infrastructure,
which allows attaching master devices to their IOMMUs automatically
according to DT properties.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:28 +02:00
Jeffy Chen
9176a303d9 iommu/rockchip: Use IOMMU device for dma mapping operations
Use the first registered IOMMU device for dma mapping operations, and
drop the domain platform device.

This is similar to exynos iommu driver.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:27 +02:00
Jeffy Chen
8fa9eb39c6 dt-bindings: iommu/rockchip: Add clock property
Add clock property, since we are going to control clocks in rockchip
iommu driver.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:27 +02:00
Tomasz Figa
f2e3a5f557 iommu/rockchip: Control clocks needed to access the IOMMU
Current code relies on master driver enabling necessary clocks before
IOMMU is accessed, however there are cases when the IOMMU should be
accessed while the master is not running yet, for example allocating
V4L2 videobuf2 buffers, which is done by the VB2 framework using DMA
mapping API and doesn't engage the master driver at all.

This patch fixes the problem by letting clocks needed for IOMMU
operation to be listed in Device Tree and making the driver enable them
for the time of accessing the hardware.

Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:26 +02:00
Tomasz Figa
bf2a5e717a iommu/rockchip: Fix TLB flush of secondary IOMMUs
Due to the bug in current code, only first IOMMU has the TLB lines
flushed in rk_iommu_zap_lines. This patch fixes the inner loop to
execute for all IOMMUs and properly flush the TLB.

Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:26 +02:00
Tomasz Figa
0416bf6479 iommu/rockchip: Use iopoll helpers to wait for hardware
This patch converts the rockchip-iommu driver to use the in-kernel
iopoll helpers to wait for certain status bits to change in registers
instead of an open-coded custom macro.

Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:26 +02:00
Tomasz Figa
f6717d727c iommu/rockchip: Fix error handling in attach
Currently if the driver encounters an error while attaching device, it
will leave the IOMMU in an inconsistent state. Even though it shouldn't
really happen in reality, let's just add proper error path to keep
things consistent.

Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:25 +02:00
Jeffy Chen
d0b912bd4c iommu/rockchip: Request irqs in rk_iommu_probe()
Move request_irq to the end of rk_iommu_probe().

Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:22 +02:00
Jeffy Chen
6d9ffaad7e iommu/rockchip: Fix error handling in probe
Add missing iommu_device_sysfs_remove in error path.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:22 +02:00
Jeffy Chen
98b72b94de iommu/rockchip: Prohibit unbind and remove
Removal of IOMMUs cannot be done reliably.

This is similar to exynos iommu driver.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2018-03-29 12:22:21 +02:00
Sebastian Reichel
be9cae2479 usb: chipidea: imx: Fix ULPI on imx53
Traditionally, PORTSC should be set before initializing ULPI phys. But
setting PORTSC before powering on the phy results in a kernel freeze
on imx53 based GE PPD. As a workaround this initializes the phy early
in the imx platform code and disables phy power management from the
core.

Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 12:03:01 +02:00
Sebastian Reichel
04e163794b usb: chipidea: imx: Cleanup ci_hdrc_imx_platform_flag
Some trivial cleanups, that do not change functionality.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 12:03:01 +02:00
Michael Trimarchi
274a1874bd usb: chipidea: usbmisc: small clean up
The register write can be done outside the if and else condition

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 12:03:01 +02:00
Michael Trimarchi
26250d540d usb: chipidea: usbmisc: evdo can be set e/o reset
evdo bit can be set or reset. We can not trust evdo bit
status after bootloader stage

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 12:03:01 +02:00
Michael Trimarchi
9618d09349 usb: chipidea: usbmisc: evdo is only specific to OTG port
The USB_PHY_CTRL_FUNC is used specific for OTG port as described
in user manual. EVDO need to be set only for index 0 that
correspond to OTG port

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 12:03:01 +02:00
Thomas Avery
049b5e2ae3 staging: rtl8723bs: Remove yield call, replace with cond_resched()
Remove yield() call. Yield does not guarantee progress, cond_resched()
is a safer alternative

Signed-off-by: Thomas Avery <tavery321@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 12:00:15 +02:00
Thomas Avery
c22da34a1b staging: rtl8723bs: Replace yield() call with cond_resched()
Remove yield call(). yield does not guarantee progress, and should not
be used. cond_resched() is a safe alternative.

Signed-off-by: Thomas Avery <tavery321@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 12:00:15 +02:00
Quytelda Kahja
8040b57ad8 staging: rtl8723bs: Remove unecessary newlines from 'odm.h'.
Remove duplicate newlines and newlines before closing braces.

Signed-off-by: Quytelda Kahja <quytelda@tamalin.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 11:59:29 +02:00
Quytelda Kahja
ec57f8641f staging: rtl8723bs: Rework 'struct _ODM_Phy_Status_Info_' coding style.
Change the typedef'd 'struct _ODM_Phy_Status_Info_' into
'struct odm_phy_info' and change the members to snake case in
order to meet the coding style guidelines.
Members:
* u8 RxPWDBAll            -> rx_pwd_ba11
* u8 SignalQuality        -> signal_quality
* s8 RxMIMOSignalQuality  -> rx_mimo_signal_quality
* u8 RxMIMOEVMdbm         -> rx_mimo_evm_dbm
* u8 RxMIMOSignalStrength -> rx_mimo_signal_strength
* u16 Cfo_short           -> cfo_short
* u16 Cfo_tail            -> cfo_tail
* s8 RxPower              -> rx_power
* s8 RecvSignalPower      -> recv_signal_power
* u8 BTRxRSSIPercentage   -> bt_rx_rssi_percentage
* u8 SignalStrength       -> signal_strength
* s8 RxPwr                -> rx_pwr
* u8 RxSNR                -> rx_snr
* u8 BandWidth            => band_width
* u8 btCoexPwrAdjust      -> bt_coex_pwr_adjust

Signed-off-by: Quytelda Kahja <quytelda@tamalin.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 11:59:29 +02:00
Quytelda Kahja
3df3602ac7 staging: rtl8723bs: Rework 'struct _ODM_Per_Pkt_Info_' coding style.
Change the typedef'd 'struct _ODM_Per_Pkt_Info_' into
'struct odm_packet_info' and change the members to snake case in
order to meet the coding style guidelines.
Members:
* u8 DataRate            -> data_rate
* u8 StationID           -> station_id
* bool bPacketMatchBSSID -> bssid_match
* bool bPacketToSelf     -> to_self
* bool bPacketBeacon     -> is_beacon
* bool bToSelf           -> (removed because it isn't used)

Signed-off-by: Quytelda Kahja <quytelda@tamalin.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 11:59:29 +02:00
Quytelda Kahja
9f534f7ee8 staging: rtl8723bs: Replace NULL pointer comparison with '!'.
Replace the comparison of 'precvbuf' to 'NULL' with '!precvbuf'.

Signed-off-by: Quytelda Kahja <quytelda@tamalin.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 11:59:29 +02:00
Quytelda Kahja
9ff7c1aadd staging: rtl8723bs: Factor out rtl8723bs_recv_tasklet() sections.
Factor out code from rtl8723bs_recv_tasklet() into helper methods
to unindent lines over 80 characters.

Signed-off-by: Quytelda Kahja <quytelda@tamalin.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 11:59:29 +02:00
Quytelda Kahja
e39c83fe8a staging: rtl8723bs: Fix function signature that goes over 80 characters.
Wrap the function parameters for rtl8723bs_c2h_packet_handler() so
the function signature doesn't exceed 80 characters.

Signed-off-by: Quytelda Kahja <quytelda@tamalin.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 11:59:28 +02:00
Quytelda Kahja
b37f9e1c38 staging: rtl8723bs: Fix lines too long in update_recvframe_attrib().
Fix lines over the 80 character limit in update_recvframe_attrib().

Signed-off-by: Quytelda Kahja <quytelda@tamalin.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29 11:59:28 +02:00