The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from sh-cpufreq driver.
The driver though prints the min/max frequency values and the same is
done from the ->ready() callback now to keep the behavior unchanged.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from sfi driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from scpi driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from sc520 driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from s3c24xx driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from qoirq driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from pxa driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from ppc_cbe driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from powernow driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from p4-clockmod driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from mediatek driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from longhaul driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from ia64-acpi driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from elanfreq driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from e_powersaver driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from cpufreq-dt driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from brcmstb driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from arm_big_little driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table in the acpi-cpufreq driver.
The driver needs to crosscheck if the max frequency corresponds to the
P-state 0 or not and the same is done from the ->ready() callback now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq table is already validated by the cpufreq core and none of
the users of cpufreq_generic_init() have any dependency on it to
validate the table as well.
Don't validate the cpufreq table anymore from cpufreq_generic_init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a preparatory commit to make policy->suspend_freq independent of
validation of the cpufreq table, as a later commit would update
cpufreq_generic_init() to not validate the cpufreq table any longer.
The driver already assumes the order in which the frequency table is
sorted and we can get the max frequency easily.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Writing to it directly does not work for Xen PV guests.
Fixes: 49275fef98 ("x86/vsyscall/64: Explicitly set _PAGE_USER in the pagetable hierarchy")
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180319143154.3742-1-boris.ostrovsky@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
GPMI driver timings derivation looks very empirical and does not use
the known timings that the core wants to use with the NAND chip, by
using local defined constants that have no special meaning from the
outside world.
Simplify the way all of this is computed and use the NAND core's SDR
timings.
Integrity of the reads/writes has been checked with nandbiterrs, speed
improvements with flash_speed on a Freescale i.MX6 DualLite/Solo SABRE
Automotive Board. Measures are below, variations of less than 150kiB/s
between tests are common and then not significant. Speeds using mode 5
are the same, while speeds using mode 0 are quite improved (+40/50%
from non-optimal computation).
Forcing timings mode 0:
=======================
Before this patch:
------------------
eraseblock write speed is 2298 KiB/s
eraseblock read speed is 3636 KiB/s
page write speed is 2136 KiB/s
page read speed is 3316 KiB/s
2 page write speed is 2199 KiB/s
2 page read speed is 3468 KiB/s
After this patch:
-----------------
eraseblock write speed is 3232 KiB/s
eraseblock read speed is 5663 KiB/s
page write speed is 2915 KiB/s
page read speed is 4904 KiB/s
2 page write speed is 3084 KiB/s
2 page read speed is 5267 KiB/s
Forcing timings mode 5:
=======================
Before this patch:
------------------
eraseblock write speed is 4338 KiB/s
eraseblock read speed is 14883 KiB/s
page write speed is 3786 KiB/s
page read speed is 12800 KiB/s
2 page write speed is 4076 KiB/s
2 page read speed is 14065 KiB/s
After this patch:
-----------------
eraseblock write speed is 4309 KiB/s
eraseblock read speed is 14712 KiB/s
page write speed is 3764 KiB/s
page read speed is 12673 KiB/s
2 page write speed is 4076 KiB/s
2 page read speed is 14065 KiB/s
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Until now the GPMI driver had its own timings logic while the core
already handles that and request the NAND controller drivers to support
the ->setup_data_interface() hook. Implement that hook by reusing the
already existing function. No real glue is necessary between core timing
delays and GPMI registers because the driver already translates the
ONFI timing modes into register values.
Make use of the core's tREA, tRLOH and tRHOH values that allow computing
more precise timings for mode [0-3] and get significantly better values
(+20% with an i.MX6 Sabre Auto board). Otherwise use the existing logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that hold all needed
ONFI parameters, remove the ONFI page from the nand_chip structure by
just allocating it during the identification phase and removing it right
after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that can held
generic parameters, remove the JEDEC page from the nand_chip structure
by just allocating it during the identification phase and removing it
right after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The MX30LF2G18AC chip declares in its parameter page supporting
SET/GET_FEATURES but when it comes to timings, experience shows that it
is not the case.
Unflag this feature for this particular chip in the nand_parameters
structure to avoid unnecessary errors and downturns.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
If SET/GET_FEATURES is available (from the parameter page), use a
bitmap to declare what feature is actually supported.
Initialize the bitmap in the core to support timing changes (only
feature used by the core), also add support for Micron specific features
used in Micron initialization code (in the init routine).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
ONFI-related parameters that will be used outside from the
identification function are stored in a separate onfi_parameters
structure embedded in nand_parameters, this small structure that
already hold generic parameters.
For now, the onfi_parameters structure is allocated statically. However,
after some deep rework in the NAND framework, it will be possible to do
dynamic allocations from the NAND identification phase, and this
strcuture will then be dynamically allocated when needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
- Debug TTL UART
- 1000M/100M/10M Ethernet RJ45
- Realtek RTL8189FTV
- Spi flash (2MB)
- One USB 2.0 HOST, One USB 2.0 OTG
This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The commit "regulatory: add NUL to request alpha2" increases the length of
alpha2 to 3. This causes a regression on brcmfmac, because
brcmf_cfg80211_reg_notifier() expect valid ISO3166 codes in the complete
array. So fix this accordingly.
Fixes: 657308f73e ("regulatory: add NUL to request alpha2")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently a SIGFPE delivered in response to a floating-point
exception trap may have si_code set to 0 on arm64. As reported by
Eric, this is a bad idea since this is the value of SI_USER -- yet
this signal is definitely not the result of kill(2), tgkill(2) etc.
and si_uid and si_pid make limited sense whereas we do want to
yield a value for si_addr (which doesn't exist for SI_USER).
It's not entirely clear whether the architecure permits a
"spurious" fp exception trap where none of the exception flag bits
in ESR_ELx is set. (IMHO the architectural intent is to forbid
this.) However, it does permit those bits to contain garbage if
the TFV bit in ESR_ELx is 0. That case isn't currently handled at
all and may result in si_code == 0 or si_code containing a FPE_FLT*
constant corresponding to an exception that did not in fact happen.
There is nothing sensible we can return for si_code in such cases,
but SI_USER is certainly not appropriate and will lead to violation
of legitimate userspace assumptions.
This patch allocates a new si_code value FPE_UNKNOWN that at least
does not conflict with any existing SI_* or FPE_* code, and yields
this in si_code for undiagnosable cases. This is probably the best
simplicity/incorrectness tradeoff achieveable without relying on
implementation-dependent features or adding a lot of code. In any
case, there appears to be no perfect solution possible that would
justify a lot of effort here.
Yielding FPE_UNKNOWN when some well-defined fp exception caused the
trap is a violation of POSIX, but this is forced by the
architecture. We have no realistic prospect of yielding the
correct code in such cases. At present I am not aware of any ARMv8
implementation that supports trapped floating-point exceptions in
any case.
The new code may be applicable to other architectures for similar
reasons.
No attempt is made to provide ESR_ELx to userspace in the signal
frame, since architectural limitations mean that it is unlikely to
provide much diagnostic value, doesn't benefit existing software
and would create ABI with no proven purpose. The existing
mechanism for passing it also has problems of its own which may
result in the wrong value being passed to userspace due to
interaction with mm faults. The implied rework does not appear
justified.
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reported-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A built-in scpi cpufreq driver cannot link against a modular
thermal framework:
drivers/cpufreq/scpi-cpufreq.o: In function `scpi_cpufreq_ready':
scpi-cpufreq.c:(.text+0x4c): undefined reference to `of_cpufreq_cooling_register'
drivers/cpufreq/scpi-cpufreq.o: In function `scpi_cpufreq_exit':
scpi-cpufreq.c:(.text+0x9c): undefined reference to `cpufreq_cooling_unregister'
This adds a Kconfig dependency that makes sure this configuration
is not possible, while allowing all configurations that can work.
Note that disabling CPU_THERMAL means we don't care about the
THERMAL dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* a couple of fixes for channel-switch;
* a few fixes for the aggregation handling code;
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAlqvejwACgkQoUecoho8
xfqVNhAAn532pP6Fa7NR5rinhfPjobP8IhC+DReiDlCB5pjLx1ezmGb2bFDKF4bf
zYIHd/MD91eZoXLFvfUeJNuaVsaCGbPr3zjL0ynsmS9FDfnmba6fQSLsbsiO6lti
s5JCydGNwEw0YST13kmt+rOykcYLqAxNuxuSS1kCSUqJK3LDA3C0fMCly+d4hG3l
/odO3LQ8giCbvGoI8+ZXmWg2BU5Hg22lNnZ/nb/0PF8YbiH0z1xV588Pt4jYSJ5S
1rRLgycDcCzL+FO3moukK8ai8VMEv6607GlQJxw+RjRrjzk7NyXMSSQ4PIwYVpfi
egDXEBwgdkHyzeSqSCTVTz/2F6y7FpBbkMbaGvf9wt2fqLp0+b8Q3GtK0vxFQ8E7
D0hr6W2O1EWOQL4nYemlhinvB4DP0L9pd1LenY8570xDWfmar9vsDyz+EWdhcfWv
HQsB3CgVrvd67mWxmePY5ZJz26xwccV8RoTVchQvxeJIHIv2IRj88X+hpy1oIZMi
Uuxu2D0W8rP459F8OWTc9J72mLgDF4/tYhFoEH0q57VfxqqkThtay+ONJHZX06Qe
7Fhgd0qYwM5dFcoifQNZN8QX3gtqmNr6b1G8sjHvxKU2WaZ5rKjq+WCBi4U1rJq1
FgLuorlCZaj3OafNuo7D7gudruyejqCFt6RS4aVT4ZrpjbDNFqY=
=bOhv
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2018-03-19' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Fourth batch of iwlwifi fixes intended for 4.16:
* a couple of fixes for channel-switch;
* a few fixes for the aggregation handling code;
We want to start using asm-goto to guarantee the absence of dynamic
branches (and thus speculation).
A primary prerequisite for this is of course that the compiler
supports asm-goto. This effecively lifts the minimum GCC version to
build an x86 kernel to gcc-4.5.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: torvalds@linux-foundation.org
Link: https://lkml.kernel.org/r/20180319201327.GJ4043@hirez.programming.kicks-ass.net
Pull in pending siginfo changes from Eric Biederman as we depend on
the definition of FPE_FLTUNK for cleaning up our floating-point exception
signal delivery (which is currently broken and using FPE_FIXME).
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
To prepare to the removal of such huge structure, a small NAND parameter
structure is allocated statically and contains only very few members
that are generic to all chips and actually used elsewhere in the code.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Just like many other Samsung models, the 670Z5E needs to use the acpi-video
backlight interface rather then the native one for backlight control to
work, add a quirk for this.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1557060
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce a driver for the ACPI Time and Alarm Device (TAD) based on
Section 9.18 of ACPI 6.2.
This driver only supports the system wakeup capabilities of the TAD
which are mandatory. Support for the RTC capabilities of the TAD
will be added to it in the future.
This driver is entirely sysfs-based. It provides attributes (under
the TAD platform device) to allow user space to manage the AC and DC
wakeup timers of the TAD: set and read their values, set and check
their expire timer wake policies, check and clear their status and
check the capabilities of the TAD reported by AML. The DC timer
attributes are only present if the TAD supports a separate DC alarm
timer.
The wakeup events handling and power management of the TAD is
expected to be taken care of by the ACPI PM domain attached to its
platform device.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In current design of ACPI container offline, Kernel emits
KOBJ_CHANGE uevent to user space to indidate that the ejection of
the container was triggered by platform. (caa73ea15 patch)
A pure KOBJ_CHANGE uevent is not enough for user space to identify
the purpose. For example, a "udevadm trigger" command can also
be used to emit change event to all udev rules. A udev rule can not
identify that the event is from kernel for offline or from udevadm
for other purpose. Then the offline action in udev rule may also be
triggered by udevadm tool.
So, similar to the change uevent of dock, kernel sends the
KOBJ_CHANGE uevent with a offline environmental data to indicate
purpose. It's useful by udev rule for using ENV{EVENT} filter.
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_dev_pm_get_state() is used to determine the range of allowable
device power states when going into S3 suspend. This is implemented
by executing the _S3D and _S3W ACPI methods.
Linux follows the ACPI spec behaviour in that when _S3D is implemented
and _S3W is not, Linux will not go into a power state deeper than the one
returned by _S3D for a wakeup-enabled device.
However, this same logic is being applied to the case when neither
_S3D nor _S3W are present, and the result is that this function
decides that the device must stay in D0 (fully on) state.
This is breaking USB wakeups on Asus V222GA and Acer XC-830. _S3D and
_S3W are not present, so the USB controller is left in the D0 running
state during S3, and hence it is unable to generate a PME# wake event.
The ACPI spec is unclear on which power states are permissable for
wakeup-enabled devices when both _S3D and _S3W are missing.
However, USB wakeups work fine on these platforms under Windows, where
device manager shows that they are using D3 device state for the USB
controller in S3.
I assume that the "max = min" clamping done by the code here is
specifically written for the _S3D but no _S3W case. By making the
code true to those conditions, avoiding them on these platforms,
the controller will be put into D3 state and USB wakeups start working.
Additionally I feel that this change makes the code more directly
mirror the wording of the ACPI spec and it's associated lack of clarity.
Thanks to Mathias Nyman for pointing us in the right direction.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Link: http://lkml.kernel.org/r/CAB4CAwf_k-WsF3zL4epm9TKAOu0h=Bv1XhXV_gY3bziOo_NPKA@mail.gmail.comhttps://phabricator.endlessm.com/T21410
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Trying quirks in usbcore needs to rebuild the driver or the entire
kernel if it's builtin. It can save a lot of time if usbcore has similar
ability like "usbhid.quirks=" and "usb-storage.quirks=".
Rename the original quirk detection function to "static" as we introduce
this new "dynamic" function.
Now users can use "usbcore.quirks=" as short term workaround before the
next kernel release. Also, the quirk parameter can XOR the builtin
quirks for debugging purpose.
This is inspired by usbhid and usb-storage.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update to show Minas Harutyunyan as the new maintainer for dwc2.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maximum bytes per interval for USB SuperSpeed Plus can be set by
isoc endpoint companion descriptor when it is above 48K. If the
descriptor is provided, then use its value.
USB 3.1 spec 9.6.8
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>