[ Upstream commit 902806baf3 ]
AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
while updating Audio InfoFrame information and then set to 0 when done.
Otherwise partially updated Audio InfoFrames could be sent out. Two
cases where this rule were not followed are fixed:
- In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
before/after setting ADV7511_REG_AUDIO_INFOFRAME.
- In audio_startup() use the correct register for clearing
AUDIO_UPDATE bit.
The problem with corrupted audio infoframes were discovered by letting
a HDMI logic analyser check the output of ADV7535.
Note that this patchs replaces writing REG_GC(1) with
REG_INFOFRAME_UPDATE. Bit 5 of REG_GC(1) is positioned within field
GC_PP[3:0] and that field doesn't control audio infoframe and is read-
only. My conclusion therefore was that the author if this code meant to
clear bit 5 of REG_INFOFRAME_UPDATE from the very beginning.
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: 53c515befe ("drm/bridge: adv7511: Add Audio support")
Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241119-adv7511-audio-info-frame-v4-1-4ae68e76c89c@axis.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25c6a5ab15 ]
On the i.MX6ULL-14x14-EVK board, enet1_ref and enet2_ref are used as the
clock sources for two external KSZ PHYs. However, after closing the two
FEC ports, the clk_enable_count of the enet1_ref and enet2_ref clocks is
not 0. The root cause is that since the commit 9853294627 ("net: phy:
micrel: use devm_clk_get_optional_enabled for the rmii-ref clock"), the
external clock of KSZ PHY has been enabled when the PHY driver probes,
and it can only be disabled when the PHY driver is removed. This causes
the clock to continue working when the system is suspended or the network
port is down.
Although Heiko explained in the commit message that the patch was because
some clock suppliers need to enable the clock to get the valid clock rate
, it seems that the simple fix is to disable the clock after getting the
clock rate to solve the current problem. This is indeed true, but we need
to admit that Heiko's patch has been applied for more than a year, and we
cannot guarantee whether there are platforms that only enable rmii-ref in
the KSZ PHY driver during this period. If this is the case, disabling
rmii-ref will cause RMII on these platforms to not work.
Secondly, commit 99ac4cbcc2 ("net: phy: micrel: allow usage of generic
ethernet-phy clock") just simply enables the generic clock permanently,
which seems like the generic clock may only be enabled in the PHY driver.
If we simply disable the generic clock, RMII may not work. If we keep it
as it is, the platform using the generic clock will have the same problem
as the i.MX6ULL platform.
To solve this problem, the clock is enabled when phy_driver::resume() is
called, and the clock is disabled when phy_driver::suspend() is called.
Since phy_driver::resume() and phy_driver::suspend() are not called in
pairs, an additional clk_enable flag is added. When phy_driver::suspend()
is called, the clock is disabled only if clk_enable is true. Conversely,
when phy_driver::resume() is called, the clock is enabled if clk_enable
is false.
The changes that introduced the problem were only a few lines, while the
current fix is about a hundred lines, which seems out of proportion, but
it is necessary because kszphy_probe() is used by multiple KSZ PHYs and
we need to fix all of them.
Fixes: 9853294627 ("net: phy: micrel: use devm_clk_get_optional_enabled for the rmii-ref clock")
Fixes: 99ac4cbcc2 ("net: phy: micrel: allow usage of generic ethernet-phy clock")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20241217063500.1424011-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9272cba0de ]
QP table handling is synchronized with destroy QP and Async
event from the HW. The same needs to be synchronized
during create_qp also. Use the same lock in create_qp also.
Fixes: 76d3ddff71 ("RDMA/bnxt_re: synchronize the qp-handle table array")
Fixes: f218d67ef0 ("RDMA/bnxt_re: Allow posting when QPs are in error")
Fixes: 84cf229f40 ("RDMA/bnxt_re: Fix the qp table indexing")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241217102649.1377704-6-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb839f3ace ]
For variable size wqe mode, the MSN table size should be
half the size of the SQ depth. Fixing this to avoid wrap
around problems in the retransmission path.
Fixes: de1d364c38 ("RDMA/bnxt_re: Add support for Variable WQE in Genp7 adapters")
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241217102649.1377704-5-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d13be54dc1 ]
For the fixed WQE case, HW supports 0xFFFF WQEs.
For variable Size WQEs, HW treats this number as
the 16 bytes slots. The maximum supported WQEs
needs to be adjusted based on the number of slots.
Set a maximum WQE limit for variable WQE scenario.
Fixes: de1d364c38 ("RDMA/bnxt_re: Add support for Variable WQE in Genp7 adapters")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241217102649.1377704-4-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5a38bf2f3 ]
Disabling the reserved wqes logic for Gen P5/P7 devices
because this workaround is required only for legacy devices.
Fixes: ecb53febfc ("RDMA/bnxt_en: Enable RDMA driver support for 57500 chip")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241217102649.1377704-3-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40be32303e ]
While creating qps, driver adds one extra entry to the sq size
passed by the ULPs in order to avoid queue full condition.
When ULPs creates QPs with max_qp_wr reported, driver creates
QP with 1 more than the max_wqes supported by HW. Create QP fails
in this case. To avoid this error, reduce 1 entry in max_qp_wqes
and report it to the stack.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241217102649.1377704-2-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7179fe0074 ]
Driver currently populates subsystem_device id in the
"hw_ver" field of ib_attr structure in query_device.
Updated to populate PCI revision ID.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Reviewed-by: Preethi G <preethi.gurusiddalingeswaraswamy@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-6-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 798653a0ee ]
When RDMA app configures path MTU, add a check in modify_qp verb
to make sure that it doesn't go beyond interface MTU. If this
check fails, driver will fail the modify_qp verb.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-3-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38651476e4 ]
The check for 9060 condition should only be made for legacy chips.
Fixes: 9152e0b722 ("RDMA/bnxt_re: HW workarounds for handling specific conditions")
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-2-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e8c520916 ]
We had BE201 hard coded.
Look at the RF_ID and decide based on its value.
Fixes: 6795a37161 ("wifi: iwlwifi: Print a specific device name.")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241212132940.b9eebda1ca60.I36791a134ed5e538e059418eb6520761da97b44c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebefac5647 ]
We initially introduced a quick fix limiting the queue depth to 1 as
experimentation showed that it fixed data corruption on 64GB steamdecks.
Further experimentation revealed corruption only happens when the last
PRP data element aligns to the end of the page boundary. The device
appears to treat this as a PRP chain to a new list instead of the data
element that it actually is. This implementation is in violation of the
spec. Encountering this errata with the Linux driver requires the host
request a 128k transfer and coincidently be handed the last small pool
dma buffer within a page.
The QD1 quirk effectly works around this because the last data PRP
always was at a 248 byte offset from the page start, so it never
appeared at the end of the page, but comes at the expense of throttling
IO and wasting the remainder of the PRP page beyond 256 bytes. Also to
note, the MDTS on these devices is small enough that the "large" prp
pool can hold enough PRP elements to never reach the end, so that pool
is not a problem either.
Introduce a new quirk to ensure the small pool is always aligned such
that the last PRP element can't appear a the end of the page. This comes
at the expense of wasting 256 bytes per small pool page allocated.
Link: https://lore.kernel.org/linux-nvme/20241113043151.GA20077@lst.de/T/#u
Fixes: 83bdfcbdbe ("nvme-pci: qdepth 1 quirk")
Cc: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4048c83fd ]
If traffic is over vlan, cma_validate_port() fails to match
net_device ifindex with bound_if_index and results in ENODEV error.
As iWARP gid table is static, it contains entry corresponding to
only one net device which is either real netdev or vlan netdev for
cases like siw attached to a vlan interface.
This patch fixes the issue by assigning bound_if_index with net
device index, if real net device obtained from bound if index matches
with net device retrieved from gid table
Fixes: f8ef1be816 ("RDMA/cma: Avoid GID lookups on iWARP devices")
Link: https://lore.kernel.org/all/ZzNgdrjo1kSCGbRz@chelsio.com/
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Link: https://patch.msgid.link/20241203140052.3985-1-anumula@chelsio.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 064c22408a ]
The workaround to modify the UD QP from RTS to RTS is required
only for older adapters. Issuing this for latest adapters can caus
some unexpected behavior. Fix it
Fixes: 1801d87b35 ("RDMA/bnxt_re: Support new 5760X P7 devices")
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241204075416.478431-4-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5effcacc8a ]
Software Queues to hold the WRs needs to be created
for only kernel queues. Avoid allocating the unnecessary
memory for user Queues.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Fixes: 159fb4ceac ("RDMA/bnxt_re: introduce a function to allocate swq")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241204075416.478431-3-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79d330fbdf ]
Gen P7 supports up to 13 SGEs for now. WQE software structure
can hold only 6 now. Since the max send sge is reported as
13, the stack can give requests up to 13 SGEs. This is causing
traffic failures and system crashes.
Use the define for max SGE supported for variable size. This
will work for both static and variable WQEs.
Fixes: 227f51743b ("RDMA/bnxt_re: Fix the max WQE size for static WQE support")
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241204075416.478431-2-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e05feab22f ]
Different core device types such as PFs and VFs shouldn't be affiliated
together since they have different capabilities, fix that by enforcing
type check before doing the affiliation.
Fixes: 32f69e4be2 ("{net, IB}/mlx5: Manage port association for multiport RoCE")
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Link: https://patch.msgid.link/88699500f690dff1c1852c1ddb71f8a1cc8b956e.1733233480.git.leonro@nvidia.com
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f24d192985 ]
sizeof when applied to a pointer typed expression gives the size of
the pointer.
The proper fix in this particular case is to code sizeof(*cpuset)
instead of sizeof(cpuset).
This issue was detected with the help of Coccinelle.
Fixes: 22a920209a ("sched_ext: Implement tickless support")
Signed-off-by: guanjing <guanjing@cmss.chinamobile.com>
Acked-by: Andrea Righi <arighi@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb867d797d ]
res->dattr is always valid at this point as it was initialized
during device addition in bnxt_re_add_device().
This change is fixing the following smatch error:
drivers/infiniband/hw/bnxt_re/qplib_fp.c:1090 bnxt_qplib_create_qp()
error: we previously assumed 'res->dattr' could be null (see line 985)
Fixes: 07f830ae49 ("RDMA/bnxt_re: Adds MSN table capability for Gen P7 adapters")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202411222329.YTrwonWi-lkp@intel.com/
Link: https://patch.msgid.link/be0d8836b64cba3e479fbcbca717acad04aae02e.1732626579.git.leonro@nvidia.com
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c3864e055 ]
Otherwise it won't catch bios turned into regular writes by the block
level zone write plugging. The additional test it adds is for emulated
zone append.
Fixes: 9b1ce7f0c6 ("block: Implement zone append emulation")
CC: stable@vger.kernel.org # 6.12
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ef2b9e698 ]
Make bio_is_zone_append globally available, because file systems need
to use to check for a zone append bio in their end_io handlers to deal
with the block layer emulation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20241104062647.91160-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 6c3864e055 ("btrfs: use bio_is_zone_append() in the completion handler")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit afc6717628 upstream.
In order to catch a common bug where a TRACE_EVENT() TP_fast_assign()
assigns an address of an allocated string to the ring buffer and then
references it in TP_printk(), which can be executed hours later when the
string is free, the function test_event_printk() runs on all events as
they are registered to make sure there's no unwanted dereferencing.
It calls process_string() to handle cases in TP_printk() format that has
"%s". It returns whether or not the string is safe. But it can have some
false positives.
For instance, xe_bo_move() has:
TP_printk("move_lacks_source:%s, migrate object %p [size %zu] from %s to %s device_id:%s",
__entry->move_lacks_source ? "yes" : "no", __entry->bo, __entry->size,
xe_mem_type_to_name[__entry->old_placement],
xe_mem_type_to_name[__entry->new_placement], __get_str(device_id))
Where the "%s" references into xe_mem_type_to_name[]. This is an array of
pointers that should be safe for the event to access. Instead of flagging
this as a bad reference, if a reference points to an array, where the
record field is the index, consider it safe.
Link: https://lore.kernel.org/all/9dee19b6185d325d0e6fa5f7cbba81d007d99166.camel@sapience.com/
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/20241231000646.324fb5f7@gandalf.local.home
Fixes: 65a25d9f7a ("tracing: Add "%s" check in test_event_printk()")
Reported-by: Genes Lists <lists@sapience.com>
Tested-by: Gene C <arch@sapience.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f64f610ec6 upstream.
The genpd device, which is really only used as a handle to lookup
OPP, but not even registered to the device core otherwise and thus
lifetime linked to the genpd struct it is contained in, is missing
a release function. After b8f7bbd1f4 ("pmdomain: core: Add
missing put_device()") the device will be cleaned up going through
the driver core device_release() function, which will warn when no
release callback is present for the device. Add a dummy release
function to shut up the warning.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Fixes: b8f7bbd1f4 ("pmdomain: core: Add missing put_device()")
Cc: stable@vger.kernel.org
Message-ID: <20241218184433.1930532-1-l.stach@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 469c0682e0 upstream.
imx_gpcv2_probe() leaks an OF node reference obtained by
of_get_child_by_name(). Fix it by declaring the device node with the
__free(device_node) cleanup construct.
This bug was found by an experimental static analysis tool that I am
developing.
Fixes: 03aa12629f ("soc: imx: Add GPCv2 power gating driver")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Cc: stable@vger.kernel.org
Message-ID: <20241215030159.1526624-1-joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d90a86ed0 upstream.
Commit c7eed31e23 ("mmc: sdhci-msm: Switch to the new ICE API")
introduced an incorrect check of the algorithm ID into the key eviction
path, and thus qcom_ice_evict_key() is no longer ever called. Fix it.
Fixes: c7eed31e23 ("mmc: sdhci-msm: Switch to the new ICE API")
Cc: stable@vger.kernel.org
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Message-ID: <20241213041958.202565-6-ebiggers@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 900f83cf37 upstream.
When evaluating extended permissions, ignore unknown permissions instead
of calling BUG(). This commit ensures that future permissions can be
added without interfering with older kernels.
Cc: stable@vger.kernel.org
Fixes: fa1aa143ac ("selinux: extended permissions for ioctls")
Signed-off-by: Thiébaud Weksteen <tweek@google.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 032fe9b051 upstream.
The HP OMEN 8 (2022), corresponding to a board ID of 8A15, supports OMEN
thermal profile and requires the timed profile quirk.
Upon adding this ID to both the omen_thermal_profile_boards and
omen_timed_thermal_profile_boards, significant bump in performance can be
observed. For instance, SilverBench (https://silver.urih.com/) results
improved from ~56,000 to ~69,000, as a result of higher power draws (and
thus core frequencies) whilst under load:
Package Power:
- Before the patch: ~65W (dropping to about 55W under sustained load).
- After the patch: ~115W (dropping to about 105W under sustained load).
Core Power:
- Before: ~60W (ditto above).
- After: ~108W (ditto above).
Add 8A15 to omen_thermal_profile_boards and
omen_timed_thermal_profile_boards to improve performance.
Signed-off-by: Xi Xiao <1577912515@qq.com>
Signed-off-by: Mingcong Bai <jeffbai@aosc.io>
Link: https://lore.kernel.org/r/20241226062207.3352629-1-jeffbai@aosc.io
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e16ae558a upstream.
F8 mode key on Lenovo 2025 platforms use a different key code.
Adding support for the new keycode 0x1401.
Tested on X1 Carbon Gen 13 and X1 2-in-1 Gen 10.
Signed-off-by: Vishnu Sankar <vishnuocv@gmail.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20241227231840.21334-1-vishnuocv@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 73dae652dc ("drm/amdgpu: rework resume handling for display (v2)")
missed a small code change when it was backported resulting in an automatic
backlight control breakage. Fix the backport.
Note that this patch is not in Linus' tree as it is not required there;
the bug was introduced in the backport.
Fixes: 99a02eab82 ("drm/amdgpu: rework resume handling for display (v2)")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3853
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.11.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 185e1b1d91 ]
mlxplat_pci_fpga_device_init() calls pci_get_device() but does not
release the refcount on error path. Call pci_dev_put() on the error path
and in mlxplat_pci_fpga_device_exit() to fix this.
This bug was found by an experimental static analysis tool that I am
developing.
Fixes: 02daa222fb ("platform: mellanox: Add initial support for PCIe based programming logic device")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20241216022538.381209-1-joe@pf.is.s.u-tokyo.ac.jp
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ed990c07af upstream.
The recent change for the legacy substream name update brought a
compile warning for some compilers due to the nature of snprintf().
Use scnprintf() to shut up the warning since the truncation is
intentional.
Fixes: e29e504e78 ("ALSA: ump: Indicate the inactive group in legacy substream names")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202411300103.FrGuTAYp-lkp@intel.com/
Link: https://patch.msgid.link/20241130090009.19849-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit defc33b554 upstream.
Change conditions for Bluetooth driver claiming and releasing usb
ISO interface for MediaTek ISO data transmission.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Fedor Pchelkin <boddah8794@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 489304e670 upstream.
MediaTek claim an special usb intr interface for ISO data transmission.
The interface need to be released before unregistering hci device when
usb disconnect. Removing BT usb dongle without properly releasing the
interface may cause Kernel panic while unregister hci device.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Fedor Pchelkin <boddah8794@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cea1805f16 upstream.
Add disconnect callback function in btusb_disconnect which is reserved
for vendor specific usage before deregister hci in btusb_disconnect.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Fedor Pchelkin <boddah8794@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad0c6f603b upstream.
Move MediaTek Bluetooth power off command before releasing
usb ISO interface.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Fedor Pchelkin <boddah8794@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e74859ee3 upstream.
When we call btrfs_read_folio() to bring a folio uptodate, we unlock the
folio. The result of that is that a different thread can modify the
mapping (like remove it with invalidate) before we call folio_lock().
This results in an invalid page and we need to try again.
In particular, if we are relocating concurrently with aborting a
transaction, this can result in a crash like the following:
BUG: kernel NULL pointer dereference, address: 0000000000000000
PGD 0 P4D 0
Oops: 0000 [#1] SMP
CPU: 76 PID: 1411631 Comm: kworker/u322:5
Workqueue: events_unbound btrfs_reclaim_bgs_work
RIP: 0010:set_page_extent_mapped+0x20/0xb0
RSP: 0018:ffffc900516a7be8 EFLAGS: 00010246
RAX: ffffea009e851d08 RBX: ffffea009e0b1880 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffc900516a7b90 RDI: ffffea009e0b1880
RBP: 0000000003573000 R08: 0000000000000001 R09: ffff88c07fd2f3f0
R10: 0000000000000000 R11: 0000194754b575be R12: 0000000003572000
R13: 0000000003572fff R14: 0000000000100cca R15: 0000000005582fff
FS: 0000000000000000(0000) GS:ffff88c07fd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000407d00f002 CR4: 00000000007706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
? __die+0x78/0xc0
? page_fault_oops+0x2a8/0x3a0
? __switch_to+0x133/0x530
? wq_worker_running+0xa/0x40
? exc_page_fault+0x63/0x130
? asm_exc_page_fault+0x22/0x30
? set_page_extent_mapped+0x20/0xb0
relocate_file_extent_cluster+0x1a7/0x940
relocate_data_extent+0xaf/0x120
relocate_block_group+0x20f/0x480
btrfs_relocate_block_group+0x152/0x320
btrfs_relocate_chunk+0x3d/0x120
btrfs_reclaim_bgs_work+0x2ae/0x4e0
process_scheduled_works+0x184/0x370
worker_thread+0xc6/0x3e0
? blk_add_timer+0xb0/0xb0
kthread+0xae/0xe0
? flush_tlb_kernel_range+0x90/0x90
ret_from_fork+0x2f/0x40
? flush_tlb_kernel_range+0x90/0x90
ret_from_fork_asm+0x11/0x20
</TASK>
This occurs because cleanup_one_transaction() calls
destroy_delalloc_inodes() which calls invalidate_inode_pages2() which
takes the folio_lock before setting mapping to NULL. We fail to check
this, and subsequently call set_extent_mapping(), which assumes that
mapping != NULL (in fact it asserts that in debug mode)
Note that the "fixes" patch here is not the one that introduced the
race (the very first iteration of this code from 2009) but a more recent
change that made this particular crash happen in practice.
Fixes: e7f1326cc2 ("btrfs: set page extent mapped after read_folio in relocate_one_page")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fba7be1ca upstream.
When we call btrfs_read_folio() we get an unlocked folio, so it is possible
for a different thread to concurrently modify folio->mapping. We must
check that this hasn't happened once we do have the lock.
CC: stable@vger.kernel.org # 6.12+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44f52bbe96 upstream.
When a COWing a tree block, at btrfs_cow_block(), and we have the
tracepoint trace_btrfs_cow_block() enabled and preemption is also enabled
(CONFIG_PREEMPT=y), we can trigger a use-after-free in the COWed extent
buffer while inside the tracepoint code. This is because in some paths
that call btrfs_cow_block(), such as btrfs_search_slot(), we are holding
the last reference on the extent buffer @buf so btrfs_force_cow_block()
drops the last reference on the @buf extent buffer when it calls
free_extent_buffer_stale(buf), which schedules the release of the extent
buffer with RCU. This means that if we are on a kernel with preemption,
the current task may be preempted before calling trace_btrfs_cow_block()
and the extent buffer already released by the time trace_btrfs_cow_block()
is called, resulting in a use-after-free.
Fix this by moving the trace_btrfs_cow_block() from btrfs_cow_block() to
btrfs_force_cow_block() before the COWed extent buffer is freed.
This also has a side effect of invoking the tracepoint in the tree defrag
code, at defrag.c:btrfs_realloc_node(), since btrfs_force_cow_block() is
called there, but this is fine and it was actually missing there.
Reported-by: syzbot+8517da8635307182c8a5@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-btrfs/6759a9b9.050a0220.1ac542.000d.GAE@google.com/
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fca432e73d upstream.
The following sysfs entries are reading super block member directly,
which can have a different endian and cause wrong values:
- sys/fs/btrfs/<uuid>/nodesize
- sys/fs/btrfs/<uuid>/sectorsize
- sys/fs/btrfs/<uuid>/clone_alignment
Thankfully those values (nodesize and sectorsize) are always aligned
inside the btrfs_super_block, so it won't trigger unaligned read errors,
just endian problems.
Fix them by using the native cached members instead.
Fixes: df93589a17 ("btrfs: export more from FS_INFO to sysfs")
CC: stable@vger.kernel.org
Reviewed-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2363e6fcc upstream.
Set squota incompat bit before committing the transaction that enables
the feature.
With the config CONFIG_BTRFS_ASSERT enabled, an assertion
failure occurs regarding the simple quota feature.
[5.596534] assertion failed: btrfs_fs_incompat(fs_info, SIMPLE_QUOTA), in fs/btrfs/qgroup.c:365
[5.597098] ------------[ cut here ]------------
[5.597371] kernel BUG at fs/btrfs/qgroup.c:365!
[5.597946] CPU: 1 UID: 0 PID: 268 Comm: mount Not tainted 6.13.0-rc2-00031-gf92f4749861b #146
[5.598450] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014
[5.599008] RIP: 0010:btrfs_read_qgroup_config+0x74d/0x7a0
[5.604303] <TASK>
[5.605230] ? btrfs_read_qgroup_config+0x74d/0x7a0
[5.605538] ? exc_invalid_op+0x56/0x70
[5.605775] ? btrfs_read_qgroup_config+0x74d/0x7a0
[5.606066] ? asm_exc_invalid_op+0x1f/0x30
[5.606441] ? btrfs_read_qgroup_config+0x74d/0x7a0
[5.606741] ? btrfs_read_qgroup_config+0x74d/0x7a0
[5.607038] ? try_to_wake_up+0x317/0x760
[5.607286] open_ctree+0xd9c/0x1710
[5.607509] btrfs_get_tree+0x58a/0x7e0
[5.608002] vfs_get_tree+0x2e/0x100
[5.608224] fc_mount+0x16/0x60
[5.608420] btrfs_get_tree+0x2f8/0x7e0
[5.608897] vfs_get_tree+0x2e/0x100
[5.609121] path_mount+0x4c8/0xbc0
[5.609538] __x64_sys_mount+0x10d/0x150
The issue can be easily reproduced using the following reproducer:
root@q:linux# cat repro.sh
set -e
mkfs.btrfs -q -f /dev/sdb
mount /dev/sdb /mnt/btrfs
btrfs quota enable -s /mnt/btrfs
umount /mnt/btrfs
mount /dev/sdb /mnt/btrfs
The issue is that when enabling quotas, at btrfs_quota_enable(), we set
BTRFS_QGROUP_STATUS_FLAG_SIMPLE_MODE at fs_info->qgroup_flags and persist
it in the quota root in the item with the key BTRFS_QGROUP_STATUS_KEY, but
we only set the incompat bit BTRFS_FEATURE_INCOMPAT_SIMPLE_QUOTA after we
commit the transaction used to enable simple quotas.
This means that if after that transaction commit we unmount the filesystem
without starting and committing any other transaction, or we have a power
failure, the next time we mount the filesystem we will find the flag
BTRFS_QGROUP_STATUS_FLAG_SIMPLE_MODE set in the item with the key
BTRFS_QGROUP_STATUS_KEY but we will not find the incompat bit
BTRFS_FEATURE_INCOMPAT_SIMPLE_QUOTA set in the superblock, triggering an
assertion failure at:
btrfs_read_qgroup_config() -> qgroup_read_enable_gen()
To fix this issue, set the BTRFS_FEATURE_INCOMPAT_SIMPLE_QUOTA flag
immediately after setting the BTRFS_QGROUP_STATUS_FLAG_SIMPLE_MODE.
This ensures that both flags are flushed to disk within the same
transaction.
Fixes: 182940f4f4 ("btrfs: qgroup: add new quota mode for simple quotas")
CC: stable@vger.kernel.org # 6.6+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Julian Sun <sunjunchao2870@gmail.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03018e5d85 upstream.
When activating a swap file, to determine if an extent is shared we use
can_nocow_extent(), which ends up at btrfs_cross_ref_exist(). That helper
is meant to be quick because it's used in the NOCOW write path, when
flushing delalloc and when doing a direct IO write, however it does return
some false positives, meaning it may indicate that an extent is shared
even if it's no longer the case. For the write path this is fine, we just
do a unnecessary COW operation instead of doing a more rigorous check
which would be too heavy (calling btrfs_is_data_extent_shared()).
However when activating a swap file, the false positives simply result
in a failure, which is confusing for users/applications. One particular
case where this happens is when a data extent only has 1 reference but
that reference is not inlined in the extent item located in the extent
tree - this happens when we create more than 33 references for an extent
and then delete those 33 references plus every other non-inline reference
except one. The function check_committed_ref() assumes that if the size
of an extent item doesn't match the size of struct btrfs_extent_item
plus the size of an inline reference (plus an owner reference in case
simple quotas are enabled), then the extent is shared - that is not the
case however, we can have a single reference but it's not inlined - the
reason we do this is to be fast and avoid inspecting non-inline references
which may be located in another leaf of the extent tree, slowing down
write paths.
The following test script reproduces the bug:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
NUM_CLONES=50
umount $DEV &> /dev/null
run_test()
{
local sync_after_add_reflinks=$1
local sync_after_remove_reflinks=$2
mkfs.btrfs -f $DEV > /dev/null
#mkfs.xfs -f $DEV > /dev/null
mount $DEV $MNT
touch $MNT/foo
chmod 0600 $MNT/foo
# On btrfs the file must be NOCOW.
chattr +C $MNT/foo &> /dev/null
xfs_io -s -c "pwrite -b 1M 0 1M" $MNT/foo
mkswap $MNT/foo
for ((i = 1; i <= $NUM_CLONES; i++)); do
touch $MNT/foo_clone_$i
chmod 0600 $MNT/foo_clone_$i
# On btrfs the file must be NOCOW.
chattr +C $MNT/foo_clone_$i &> /dev/null
cp --reflink=always $MNT/foo $MNT/foo_clone_$i
done
if [ $sync_after_add_reflinks -ne 0 ]; then
# Flush delayed refs and commit current transaction.
sync -f $MNT
fi
# Remove the original file and all clones except the last.
rm -f $MNT/foo
for ((i = 1; i < $NUM_CLONES; i++)); do
rm -f $MNT/foo_clone_$i
done
if [ $sync_after_remove_reflinks -ne 0 ]; then
# Flush delayed refs and commit current transaction.
sync -f $MNT
fi
# Now use the last clone as a swap file. It should work since
# its extent are not shared anymore.
swapon $MNT/foo_clone_${NUM_CLONES}
swapoff $MNT/foo_clone_${NUM_CLONES}
umount $MNT
}
echo -e "\nTest without sync after creating and removing clones"
run_test 0 0
echo -e "\nTest with sync after creating clones"
run_test 1 0
echo -e "\nTest with sync after removing clones"
run_test 0 1
echo -e "\nTest with sync after creating and removing clones"
run_test 1 1
Running the test:
$ ./test.sh
Test without sync after creating and removing clones
wrote 1048576/1048576 bytes at offset 0
1 MiB, 1 ops; 0.0017 sec (556.793 MiB/sec and 556.7929 ops/sec)
Setting up swapspace version 1, size = 1020 KiB (1044480 bytes)
no label, UUID=a6b9c29e-5ef4-4689-a8ac-bc199c750f02
swapon: /mnt/sdi/foo_clone_50: swapon failed: Invalid argument
swapoff: /mnt/sdi/foo_clone_50: swapoff failed: Invalid argument
Test with sync after creating clones
wrote 1048576/1048576 bytes at offset 0
1 MiB, 1 ops; 0.0036 sec (271.739 MiB/sec and 271.7391 ops/sec)
Setting up swapspace version 1, size = 1020 KiB (1044480 bytes)
no label, UUID=5e9008d6-1f7a-4948-a1b4-3f30aba20a33
swapon: /mnt/sdi/foo_clone_50: swapon failed: Invalid argument
swapoff: /mnt/sdi/foo_clone_50: swapoff failed: Invalid argument
Test with sync after removing clones
wrote 1048576/1048576 bytes at offset 0
1 MiB, 1 ops; 0.0103 sec (96.665 MiB/sec and 96.6651 ops/sec)
Setting up swapspace version 1, size = 1020 KiB (1044480 bytes)
no label, UUID=916c2740-fa9f-4385-9f06-29c3f89e4764
Test with sync after creating and removing clones
wrote 1048576/1048576 bytes at offset 0
1 MiB, 1 ops; 0.0031 sec (314.268 MiB/sec and 314.2678 ops/sec)
Setting up swapspace version 1, size = 1020 KiB (1044480 bytes)
no label, UUID=06aab1dd-4d90-49c0-bd9f-3a8db4e2f912
swapon: /mnt/sdi/foo_clone_50: swapon failed: Invalid argument
swapoff: /mnt/sdi/foo_clone_50: swapoff failed: Invalid argument
Fix this by reworking btrfs_swap_activate() to instead of using extent
maps and checking for shared extents with can_nocow_extent(), iterate
over the inode's file extent items and use the accurate
btrfs_is_data_extent_shared().
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c8507c63f upstream.
During swap activation we iterate over the extents of a file and we can
have many thousands of them, so we can end up in a busy loop monopolizing
a core. Avoid this by doing a voluntary reschedule after processing each
extent.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0525064bb8 upstream.
When activating the swap file we flush all delalloc and wait for ordered
extent completion, so that we don't miss any delalloc and extents before
we check that the file's extent layout is usable for a swap file and
activate the swap file. We are called with the inode's VFS lock acquired,
so we won't race with buffered and direct IO writes, however we can still
race with memory mapped writes since they don't acquire the inode's VFS
lock. The race window is between flushing all delalloc and locking the
whole file's extent range, since memory mapped writes lock an extent range
with the length of a page.
Fix this by acquiring the inode's mmap lock before we flush delalloc.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afc6e39e82 upstream.
Fix set charge current limits for devices which allow to set the lowest
charge current limit to be greater zero. If requested charge current limit
is below lowest limit, the index equals current_limit_map_size which leads
to accessing memory beyond allocated memory.
Fixes: be2919d835 ("power: supply: gpio-charger: add charge-current-limit feature")
Cc: stable@vger.kernel.org
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Link: https://lore.kernel.org/r/20241209-fix-charge-current-limit-v1-1-760d9b8f2af3@liebherr.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c28dc9fc24 upstream.
ECs implementing the v2 command will not stop charging when the end
threshold is reached. Instead they will begin discharging until the
start threshold is reached, leading to permanent charge and discharge
cycles. This defeats the point of the charge control mechanism.
Avoid the issue by hiding the start threshold on v2 systems.
Instead on those systems program the EC with start == end which forces
the EC to reach and stay at that level.
v1 does not support thresholds and v3 works correctly,
at least judging from the code.
Reported-by: Thomas Koch <linrunner@gmx.net>
Fixes: c6ed48ef52 ("power: supply: add ChromeOS EC based charge control driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241208-cros_charge-control-v2-v1-3-8d168d0f08a3@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e65a1b7fad upstream.
Allow setting the start and stop thresholds to the same value.
There is no reason to disallow it.
Suggested-by: Thomas Koch <linrunner@gmx.net>
Fixes: c6ed48ef52 ("power: supply: add ChromeOS EC based charge control driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241208-cros_charge-control-v2-v1-2-8d168d0f08a3@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
