Supported number of ntuple filters affect also maximum location value that
can be provided to ethtool command. Update error message to provide info
about max supported value.
Fix double spaces in the error messages.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Pawel Kaminski <pawel.kaminski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If Clock Generation Unit is present on NIC board user shall know its
details.
Provide the devlink info callback with a new:
- fixed type object (cgu.id) indicating hardware variant of onboard CGU,
- running type object (fw.cgu) consisting of CGU id, config and firmware
versions.
These information shall be known for debugging purposes.
Test (on NIC board with CGU)
$ devlink dev info <bus_name>/<dev_name> | grep cgu
cgu.id 36
fw.cgu 8032.16973825.6021
Test (on NIC board without CGU)
$ devlink dev info <bus_name>/<dev_name> | grep cgu -c
0
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
To make sure that we don't unintentionally perform any unclocked and/or
unpowered R/W operation on GPU registers, before turning off clocks and
regulators we must make sure that no GPU, JOB or MMU ISR execution is
pending: doing that requires to add a mechanism to synchronize the
interrupts on suspend.
Add functions panfrost_{gpu,job,mmu}_suspend_irq() which will perform
interrupts masking and ISR execution synchronization, and then call
those in the panfrost_device_runtime_suspend() handler in the exact
sequence of job (may require mmu!) -> mmu -> gpu.
As a side note, JOB and MMU suspend_irq functions needed some special
treatment: as their interrupt handlers will unmask interrupts, it was
necessary to add an `is_suspended` bitmap which is used to address the
possible corner case of unintentional IRQ unmasking because of ISR
execution after a call to synchronize_irq().
At resume, clear each is_suspended bit in the reset path of JOB/MMU
to allow unmasking the interrupts.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231204114215.54575-4-angelogioacchino.delregno@collabora.com
In preparation for adding a IRQ synchronization mechanism for PM suspend,
add gpu_irq and mmu_irq variables to struct panfrost_device and change
functions panfrost_gpu_init() and panfrost_mmu_init() to use those.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231204114215.54575-3-angelogioacchino.delregno@collabora.com
Some SoCs may be equipped with a GPU containing two core groups
and this is exactly the case of Samsung's Exynos 5422 featuring
an ARM Mali-T628 MP6 GPU: the support for this GPU in Panfrost
is partial, as this driver currently supports using only one
core group and that's reflected on all parts of it, including
the power on (and power off, previously to this patch) function.
The issue with this is that even though executing the soft reset
operation should power off all cores unconditionally, on at least
one platform we're seeing a crash that seems to be happening due
to an interrupt firing which may be because we are calling power
transition only on the first core group, leaving the second one
unchanged, or because ISR execution was pending before entering
the panfrost_gpu_power_off() function and executed after powering
off the GPU cores, or all of the above.
Finally, solve this by:
- Avoid to enable the power transition interrupt on reset; and
- Ignoring the core_mask and ask the GPU to poweroff both core groups
Fixes: 22aa1a2090 ("drm/panfrost: Really power off GPU cores in panfrost_gpu_power_off()")
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231204114215.54575-2-angelogioacchino.delregno@collabora.com
CONFIG_DEBUG_SLAB is going away with CONFIG_SLAB, so remove dead ifdefs
in mempool and dmapool code.
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: David Rientjes <rientjes@google.com>
Tested-by: David Rientjes <rientjes@google.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
In slab_common.c and slab.h headers, we can now remove all code behind
CONFIG_SLAB and CONFIG_DEBUG_SLAB ifdefs, and remove all CONFIG_SLUB
ifdefs.
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: David Rientjes <rientjes@google.com>
Tested-by: David Rientjes <rientjes@google.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
The CPUHP_SLAB_PREPARE hooks are only used by SLAB which is removed.
SLUB defines them as NULL, so we can remove those altogether.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Rientjes <rientjes@google.com>
Tested-by: David Rientjes <rientjes@google.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
With SLAB removed, these are never true anymore so we can clean up.
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: David Rientjes <rientjes@google.com>
Tested-by: David Rientjes <rientjes@google.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Some struct slab fields are initialized differently for SLAB and SLUB so
we can simplify with SLUB being the only remaining allocator.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Marco Elver <elver@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Tested-by: David Rientjes <rientjes@google.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
With SLAB removed and SLUB the only remaining allocator, we can clean up
some code that was depending on the choice.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Marco Elver <elver@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Acked-by: David Rientjes <rientjes@google.com>
Tested-by: David Rientjes <rientjes@google.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Pedro Tammela says:
====================
net/sched: act_api: contiguous action arrays
When dealing with action arrays in act_api it's natural to ask if they
are always contiguous (no NULL pointers in between). Yes, they are in
all cases so far, so make use of the already present tcf_act_for_each_action
macro to explicitly document this assumption.
There was an instance where it was not, but it was refactorable (patch 2)
to make the array contiguous.
v1->v2:
- Respin
- Added Jamal's acked-by
====================
Link: https://lore.kernel.org/r/20231201175015.214214-1-pctammela@mojatatu.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The actions array is contiguous, so stop processing whenever a NULL
is found. This is already the assumption for tcf_action_destroy[1],
which is called from tcf_actions_init.
[1] https://elixir.bootlin.com/linux/v6.7-rc3/source/net/sched/act_api.c#L1115
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ops array is contiguous, so stop processing whenever a NULL is found
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In tcf_action_add, when putting the reference for the bound actions
it assigns NULLs to just created actions passing a non contiguous
array to tcf_action_put_many.
Refactor the code so the actions array is always contiguous.
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use the auxiliary macro tcf_act_for_each_action in all the
functions that expect a contiguous action array
Suggested-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Remove CONFIG_SLAB, CONFIG_DEBUG_SLAB, CONFIG_SLAB_DEPRECATED and
everything in Kconfig files and mm/Makefile that depends on those. Since
SLUB is the only remaining allocator, remove the allocator choice, make
CONFIG_SLUB a "def_bool y" for now and remove all explicit dependencies
on SLUB or SLAB as it's now always enabled. Make every option's verbose
name and description refer to "the slab allocator" without refering to
the specific implementation. Do not rename the CONFIG_ option names yet.
Everything under #ifdef CONFIG_SLAB, and mm/slab.c is now dead code, all
code under #ifdef CONFIG_SLUB is now always compiled.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Christoph Lameter <cl@linux.com>
Acked-by: David Rientjes <rientjes@google.com>
Tested-by: David Rientjes <rientjes@google.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
The SLAB implementation is going to be removed, and mm-api.rst currently
uses mm/slab.c to obtain kerneldocs for some API functions. Switch it to
mm/slub.c and move the relevant kerneldocs of exported functions from
one to the other. The rest of kerneldocs in slab.c is for static SLAB
implementation-specific functions that don't have counterparts in slub.c
and thus can be simply removed with the implementation.
Acked-by: David Rientjes <rientjes@google.com>
Tested-by: David Rientjes <rientjes@google.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Hangbin Liu says:
====================
Doc: update bridge doc
The current bridge kernel doc is too old. It only pointed to the
linuxfoundation wiki page which lacks of the new features.
Here let's start the new bridge document and put all the bridge info
so new developers and users could catch up the last bridge status soon.
v3 -> v4:
- Patch01: Reference and borrow definitions from the IEEE 802.1Q-2022 standard
for bridge (Stephen Hemminger)
- Patch04: Remind that kAPI is unstable. Add back sysfs part, but only note
that sysfs is deprecated. (Stephen Hemminger, Florian Fainelli)
- Patch05: Mention the RSTP and IEEE 802.1D developing info. (Stephen Hemminger)
- Some other grammar fixes.
v2 -> v3:
- Split the bridge doc update and adding kAPI/uAPI field to 2 part (Nikolay Aleksandrov)
- Update bridge and bridge enum descriptions (Nikolay Aleksandrov)
- Add user space stp help for STP doc (Vladimir Oltean)
v1 -> v2:
- Update bridge and bridge port enum descriptions (Vladimir Oltean)
RFCv3 -> v1:
- Fix up various typos, grammar and technical issues (Nikolay Aleksandrov)
RFCv2 -> RFCv3:
- Update netfilter part (Florian Westphal)
- Break the one large patch in to multiparts for easy reviewing. Please tell
me if I break it too much.. (Nikolay Aleksandrov)
- Update the description of each enum and doc (Nikolay Aleksandrov)
- Add more descriptions for STP/Multicast/VLAN.
RFCv1 -> RFCv2:
- Drop the python tool that generate iproute man page from kernel doc
====================
Link: https://lore.kernel.org/r/20231201081951.1623069-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add some features that are not appropriate for the existing section to
the "Others" part of the bridge document.
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add switchdev part for bridge document.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add multicast part for bridge document.
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add VLAN part for bridge document.
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add STP part for bridge document.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add document for IFLA_BRPORT enum so we can use it in
Documentation/networking/bridge.rst.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add document for IFLA_BR enum so we can use it in
Documentation/networking/bridge.rst.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The current bridge kernel doc is too old. It only pointed to the
linuxfoundation wiki page which lacks of the new features.
Here let's start the new bridge document and put all the bridge info
so new developers and users could catch up the last bridge status soon.
In this patch, Convert the doc to rst format. Add bridge brief introduction,
FAQ and contact info.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the reference manual under "2.8.6 NIU Clock gating reliance"
it is stated that pclk_usb_niu has a dependency on hclk_usb_niu.
While the manual does not state that this is a bi-directional
relationship it was noted that the sdmmc2 failed to operate for me in
mmc mode if the pclk_usb was not marked as critical. The parent clock
of the hclk_sdmmc2 is hclk_usb.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20231204185719.569021-8-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for a PLL rate of 126.4MHz so that the Powkiddy X55 panel
can run at a requested 60hz.
I have confirmed this rate fits with all the constraints
listed in the TRM for the VPLL (as an integer PLL) in Part 1 "Chapter
2 Clock & Reset Unit (CRU)."
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20231204185719.569021-9-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The current updated scheme (which this series implemented) is:
- node partial slabs: PG_Workingset && !frozen
- cpu partial slabs: !PG_Workingset && !frozen
- cpu slabs: !PG_Workingset && frozen
- full slabs: !PG_Workingset && !frozen
The most important change is that "frozen" bit is not set for the
cpu partial slabs anymore, __slab_free() will grab node list_lock
then check by !PG_Workingset that it's not on a node partial list.
And the "frozen" bit is still kept for the cpu slabs for performance,
since we don't need to grab node list_lock to check whether the
PG_Workingset is set or not if the "frozen" bit is set in __slab_free().
Update related documentations and comments in the source.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Acked-by: Christoph Lameter (Ampere) <cl@linux.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Since all partial slabs on the CPU partial list are not frozen anymore,
we don't unfreeze when moving cpu partial slabs to node partial list,
it's better to rename these functions.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Since the introduce of unfrozen slabs on cpu partial list, we don't
need to synchronize the slab frozen state under the node list_lock.
The caller of deactivate_slab() and the caller of __slab_free() won't
manipulate the slab list concurrently.
So we can get node list_lock in the last stage if we really need to
manipulate the slab list in this path.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Current, the dewake_scanline variable is defined as unsigned int,
an unsigned int variable that is always greater than or equal to 0.
when _intel_dsb_commit function is called by intel_dsb_commit function,
the dewake_scanline variable may have an int value.
So the dewake_scanline variable is necessary to defined as an int.
Fixes: f83b94d237 ("drm/i915/dsb: Use DEwake to combat PkgC latency")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310052201.AnVbpgPr-lkp@intel.com/
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: heminhong <heminhong@kylinos.cn>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114024341.14524-1-heminhong@kylinos.cn
(cherry picked from commit ef32c3cc9c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We have no bigjoiner support in the MST code, so .mode_valid()
pretending otherwise is just going to result black screens for
users. Reject any mode that needs the joiner.
Cc: stable@vger.kernel.org
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: d51f25eb47 ("drm/i915: Add DSC support to MST path")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 9c058492b1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Apparently some BXT/GLK systems have DSI panels whose timings
don't agree with the normal cpu transcoder hblank>=32 limitation.
This is perhaps fine as there are no specific hblank/etc. limits
listed for the BXT/GLK DSI transcoders.
Move those checks out from the global intel_mode_valid() into
into connector specific .mode_valid() hooks, skipping BXT/GLK
DSI connectors. We'll leave the basic [hv]display/[hv]total
checks in intel_mode_valid() as those seem like sensible upper
limits regardless of the transcoder used.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9720
Fixes: 8f4b1068e7 ("drm/i915: Check some transcoder timing minimum limits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit e0ef2daa8c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The i.MX8MP and i.MX8MQ devices both use the same DWC3 controller and
are both affected by a known issue with the controller due to specific
behaviour when park mode is enabled in SuperSpeed host mode operation.
Under heavy USB traffic from multiple endpoints the controller will
sometimes incorrectly process transactions such that some transactions
are lost, or the controller may hang when processing transactions. When
the controller hangs it does not recover.
This issue is documented partially within the linux-imx vendor kernel
which references a Synopsys STAR number 9001415732 in commits [1] and
additional details in [2]. Those commits provide some additional
controller internal implementation specifics around the incorrect
behaviour of the SuperSpeed host controller operation when park mode is
enabled.
The summary of this issue is that the host controller can incorrectly
enter/exit park mode such that part of the controller is in a state
which behaves as if in park mode even though it is not. In this state
the controller incorrectly calculates the number of TRBs available which
results in incorrect access of the internal caches causing the overwrite
of pending requests in the cache which should have been processed but
are ignored. This can cause the controller to drop the requests or hang
waiting for the pending state of the dropped requests.
The workaround for this issue is to disable park mode for SuperSpeed
operation of the controller through the GUCTL1[17] bit. This is already
available as a quirk for the DWC3 controller and can be enabled via the
'snps,parkmode-disable-ss-quirk' device tree property.
It is possible to replicate this failure on an i.MX8MP EVK with a USB
Hub connecting 4 SuperSpeed USB flash drives. Performing continuous
small read operations (dd if=/dev/sd... of=/dev/null bs=16) on the block
devices will result in device errors initially and will eventually
result in the controller hanging.
[13240.896936] xhci-hcd xhci-hcd.0.auto: WARN Event TRB for slot 4 ep 2 with no TDs queued?
[13240.990708] usb 2-1.3: reset SuperSpeed USB device number 5 using xhci-hcd
[13241.015582] sd 2:0:0:0: [sdc] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x07 driverbyte=DRIVER_OK cmd_age=0s
[13241.025198] sd 2:0:0:0: [sdc] tag#0 CDB: opcode=0x28 28 00 00 00 03 e0 00 01 00 00
[13241.032949] I/O error, dev sdc, sector 992 op 0x0:(READ) flags 0x80700 phys_seg 25 prio class 2
[13272.150710] usb 2-1.2: reset SuperSpeed USB device number 4 using xhci-hcd
[13272.175469] sd 1:0:0:0: [sdb] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x03 driverbyte=DRIVER_OK cmd_age=31s
[13272.185365] sd 1:0:0:0: [sdb] tag#0 CDB: opcode=0x28 28 00 00 00 03 e0 00 01 00 00
[13272.193385] I/O error, dev sdb, sector 992 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2
[13434.846556] xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command
[13434.854592] xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
[13434.862553] xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
[1] 97a5349d93
[2] b4b5cbc5a1
Fixes: fb8587a2c1 ("arm64: dtsi: imx8mp: add usb nodes")
Fixes: ad37549cb5 ("arm64: dts: imx8mq: add USB nodes")
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Timings taken from the datasheet, although sometimes there are just
typical values and it's not clear if they are no min and max values or
if you must use the typical value exactly. To make things worse, there
is no back porch but only a combined sync and back porch length.
Unfortunately, there is not public datasheet. Therefore, here are the
relevant timings:
| min | typ | max |
-----------------+-----+--------+-----+
CLK frequency | - | 25.175 | - |
HS period | - | 800 | - |
HS pulse width | 5 | 30 | - |
HS-DEN time | 112 | 144 | 175 |
DEN pulse width | - | 640 | - |
VS pulse width | 1 | 3 | 5 |
VS-DEN time | - | 35 | - |
VS period | - | 525 | - |
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231123102404.2022201-2-mwalle@kernel.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231123102404.2022201-2-mwalle@kernel.org
SoC TRM, SoC datasheet and board schematics always refer to the
same uart numbers - even if not all are used for a specific board.
In order to not have to re-define them for every board move the
aliases to SoC dtsi for RK3128 like it's being done for all other
Rockchip ARM SoCs.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20231202130506.66738-5-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
SoC TRM, SoC datasheet and board schematics always refer to the
same i2c numbers - even if not all are used for a specific board.
In order to not have to re-define them for every board move the
aliases to SoC dtsi for RK3128 like it's being done for all other
Rockchip ARM SoCs.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20231202130506.66738-4-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
SoC TRM, SoC datasheet and board schematics always refer to the
same gpio numbers - even if not all are used for a specific board.
In order to not have to re-define them for every board move the
aliases to SoC dtsi for RK3128 like it's being done for most other
Rockchip ARM SoCs.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20231202130506.66738-3-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
This patch adds the initial device tree for this device, it is largely
based off the device trees for mainline Edgeble Neu2 and downstream
Rockchip rv1126-evb-v13 configs. It has been adapted with relevant
peripheral and GPIO pins for the iHost.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://lore.kernel.org/r/20231203124004.2676174-8-tim@feathertop.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>