Allow writing a complete set of masks to ap_config. Doing so will
cause the vfio-ap driver to replace the vfio-ap mediated device's
matrix masks with the given set of masks. If the given state cannot
be set, then no changes are made to the vfio-ap mediated device.
The format of the data written to ap_config is as follows:
{amask},{dmask},{cmask}\n
\n is a newline character.
amask, dmask, and cmask are masks identifying which adapters, domains,
and control domains should be assigned to the mediated device.
The format of a mask is as follows:
0xNN..NN
Where NN..NN is 64 hexadecimal characters representing a 256-bit value.
The leftmost (highest order) bit represents adapter/domain 0.
For an example set of masks that represent your mdev's current
configuration, simply cat ap_config.
This attribute is intended to be used by an mdevctl callout script
supporting the mdev type vfio_ap-passthrough to atomically update a
vfio-ap mediated device's state.
Signed-off-by: "Jason J. Herne" <jjherne@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Tested-by: Matthew Rosato <mjrosato@linux.ibm.com>
Link: https://lore.kernel.org/r/20240415152555.13152-5-jjherne@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
vfio_ap_mdev_link_queue is changed to detect if a matrix_mdev has
already linked the given queue. If so, it bails out.
Signed-off-by: "Jason J. Herne" <jjherne@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Link: https://lore.kernel.org/r/20240415152555.13152-4-jjherne@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Add ap_config sysfs attribute. This will provide the means for
setting or displaying the adapters, domains and control domains assigned
to the vfio-ap mediated device in a single operation. This sysfs
attribute is comprised of three masks: One for adapters, one for domains,
and one for control domains.
This attribute is intended to be used by mdevctl to query a vfio-ap
mediated device's state.
Signed-off-by: "Jason J. Herne" <jjherne@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Tested-by: Matthew Rosato <mjrosato@linux.ibm.com>
Link: https://lore.kernel.org/r/20240415152555.13152-3-jjherne@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Rename hex2bitmap() to ap_hex2bitmap() and export it for external
use. This function will be used by the implementation of the vfio-ap
ap_config sysfs attribute.
Signed-off-by: "Jason J. Herne" <jjherne@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Link: https://lore.kernel.org/r/20240415152555.13152-2-jjherne@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
The function __storage_key_init_range() expects the end address to be
the first byte outside the range to be initialized. I.e. end - start
should be the size of the area to be initialized.
The current code works because __storage_key_init_range() will still loop
over every page in the range, but it is slower than using sske_frame().
Fixes: 3afdfca698 ("s390/mm: Clear skeys for newly mapped huge guest pmds")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Link: https://lore.kernel.org/r/20240416114220.28489-3-imbrenda@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
The function __storage_key_init_range() expects the end address to be
the first byte outside the range to be initialized. I.e. end - start
should be the size of the area to be initialized.
The current code works because __storage_key_init_range() will still loop
over every page in the range, but it is slower than using sske_frame().
Fixes: 964c2c05c9 ("s390/mm: Clear huge page storage keys on enable_skey")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Link: https://lore.kernel.org/r/20240416114220.28489-2-imbrenda@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Resource selector pair 0 is always implemented and reserved. We must not
touch it, even during save/restore for CPU Idle. Rest of the driver is
well behaved. Fix the offending ones.
Reported-by: Yabin Cui <yabinc@google.com>
Fixes: f188b5e76a ("coresight: etm4x: Save/restore state across CPU low power states")
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Yabin Cui <yabinc@google.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Link: https://lore.kernel.org/r/20240412142702.2882478-5-suzuki.poulose@arm.com
ETM4x implements TRCQCLTR only when the Q elements are supported
and the Q element filtering is supported (TRCIDR0.QFILT). Access
to the register otherwise could be fatal. Fix this by tracking the
availability, like the others.
Fixes: f188b5e76a ("coresight: etm4x: Save/restore state across CPU low power states")
Reported-by: Yabin Cui <yabinc@google.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Yabin Cui <yabinc@google.com>
Link: https://lore.kernel.org/r/20240412142702.2882478-4-suzuki.poulose@arm.com
ETM4x doesn't support Data trace on A class CPUs. As such do not access the
Data trace control registers during CPU idle. This could cause problems for
ETE. While at it, remove all references to the Data trace control registers.
Fixes: f188b5e76a ("coresight: etm4x: Save/restore state across CPU low power states")
Reported-by: Yabin Cui <yabinc@google.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Yabin Cui <yabinc@google.com>
Link: https://lore.kernel.org/r/20240412142702.2882478-3-suzuki.poulose@arm.com
When we restore the register state for ETM4x, while coming back
from CPU idle, we hardcode IOMEM access. This is wrong and could
blow up for an ETM with system instructions access (and for ETE).
Fixes: f5bd523690 ("coresight: etm4x: Convert all register accesses")
Reported-by: Yabin Cui <yabinc@google.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Yabin Cui <yabinc@google.com>
Link: https://lore.kernel.org/r/20240412142702.2882478-2-suzuki.poulose@arm.com
Define my kernel.org address to be the canonical one, and add mailmap
entries for the various addresses (including typos) that have been
used over the years.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX95 has BLK CTL modules in various MIXes, the BLK CTL modules
support clock features such as mux/gate/div. This patch
is to add the clock feature of BLK CTL modules
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240401-imx95-blk-ctl-v6-4-84d4eca1e759@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
i.MX95 DISPLAY_MASTER_CSR includes registers to control DSI clock settings,
clock gating, and pixel link select. Add dt-schema for it.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20240401-imx95-blk-ctl-v6-3-84d4eca1e759@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
i.MX95 includes BLK CTL module in several MIXes, such as VPU_CSR in
VPUMIX, CAMERA_CSR in CAMERAMIX and etc.
The BLK CTL module is used for various settings of a specific MIX, such
as clock, QoS and etc.
This patch is to add some BLK CTL modules that has clock features.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20240401-imx95-blk-ctl-v6-2-84d4eca1e759@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
New CPU #defines encode vendor and family as well as model.
Update the example usage comment in arch/x86/kernel/cpu/match.c
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240416211941.9369-4-tony.luck@intel.com
To avoid adding a slew of new macros for each new Intel CPU family
switch over from providing CPU model number #defines to a new
scheme that encodes vendor, family, and model in a single number.
[ bp: s/casted/cast/g ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240416211941.9369-3-tony.luck@intel.com
Refactor struct cpuinfo_x86 so that the vendor, family, and model
fields are overlaid in a union with a 32-bit field that combines
all three (together with a one byte reserved field in the upper
byte).
This will make it easy, cheap, and reliable to check all three
values at once.
See
https://lore.kernel.org/r/Zgr6kT8oULbnmEXx@agluck-desk3
for why the ordering is (low-to-high bits):
(vendor, family, model)
[ bp: Move comments over the line, add the backstory about the
particular order of the fields. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240416211941.9369-2-tony.luck@intel.com
On some ACPI platforms, such as Chromebooks the ACPI methods to
change the power-state (_PS0 and _PS3) fully take care of powering
on/off the sensor.
On other ACPI platforms, such as e.g. various HP models with IPU6 +
hi556 sensor, the sensor driver must control the avdd regulator itself.
Add support for having the driver control the sensor's avdd regulator.
Note this relies on the regulator-core providing a dummy regulator
(which it does by default) on platforms where Linux is not aware of
the avdd regulator.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
On some ACPI platforms, such as Chromebooks the ACPI methods to
change the power-state (_PS0 and _PS3) fully take care of powering
on/off the sensor.
On other ACPI platforms, such as e.g. various HP models with IPU6 +
hi556 sensor, the sensor driver must control the sensor's clock itself.
Add support for having the driver control an optional clock.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
On some ACPI platforms, such as Chromebooks the ACPI methods to
change the power-state (_PS0 and _PS3) fully take care of powering
on/off the sensor.
On other ACPI platforms, such as e.g. various HP models with IPU6 +
hi556 sensor, the sensor driver must control the reset GPIO itself.
Add support for having the driver control an optional reset GPIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With ipu bridge, endpoints may only be created when ipu bridge has
initialised. This may happen after the sensor driver has first probed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add camera orientation and sensor rotation controls using
the v4l2_fwnode_device_parse() and v4l2_ctrl_new_fwnode_properties()
helpers.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add hblank control so that the sensor has all the mandatory
controls for libcamera.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add vblank control to allow changing the framerate /
higher exposure values.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The hts, vts ov2680_mode struct members always contain
OV2680_PIXELS_PER_LINE resp. OV2680_LINES_PER_FRAME,
drop them and simply use these values directly.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is no reason to send OV2680_END_MARGIN extra columns on top of
the mode width and the same for sending extra lines over the mode height.
This sending of extra lines/columns was inherited from the atomisp
ov2680 driver, it is unclear why this was done and this complicates
adding V4L2_CID_VBLANK support, so remove it.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Since commit 63b0cd30b7 ("media: ov2680: Add bus-cfg / endpoint
property verification") the ov2680 driver no longer probes when the
'data-lanes' property is absent.
The OV2680 sensor has only one data lane, so there is no need for
describing it the devicetree.
Remove the unnecessary data-lanes property check.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Fixes: 63b0cd30b7 ("media: ov2680: Add bus-cfg / endpoint property verification")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The sensor gain (both analog and digital) are controlled by a
single gain value where:
- 0dB to 30dB correspond to analog gain
- 30.3dB to 72dB correspond to digital gain
(with 0.3dB step)
Hence, limit the analogue gain value to 100.
For digital gain, support can be added later if needed.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The imx335 reports a recommended pixel area of - 2592x1944.
The driver supported mode however limits it to height=1940.
Fix the height discrepency by correctly the value of height
(with updates to vblank and mode registers).
The IMX335_REG_HTRIMMING should also be corrected to the start
offset(i.e. 48) instead of chosing a abritrary crop start of 384.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Consider integer values for registers that are related to various
sizes in the register map. This helps in improving the overall
readability.
No functional changes intended in this patch.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the new comon CCI register access helpers to replace the private
register access helpers in the imx335 driver.
Select V4L2_CCI_I2C Kconfig option which the imx335 driver now
depends on.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Call the V4L2 fwnode device parser to handle controls that are
standardised by the framework.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The IMX335 can support both 2 and 4 lane configurations.
Extend the driver to configure the lane mode accordingly.
Update the pixel rate depending on the number of lanes in use.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: fixup missing : in @lane_mode kerneldoc line]
If the control handler is in an error state, return that error immediately
in v4l2_ctrl_new_fwnode_properties(). Effectively the change here is that
the same error code (handler's error) is returned in all cases instead of
possibly returning -EINVAL.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the current firmware path in linux-firmware repository. Check the
older paths still in order to avoid causing issues to the users.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Turn on the privacy LED only if streamon succeeds. This can be done after
enabling streaming on the sensor.
Fixes: b6e10ff6c2 ("media: v4l2-core: Make the v4l2-core code enable/disable the privacy LED if present")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
After the frame is submitted to DMA, it may happen that the submitted
list is not updated soon enough, and the DMA callback is triggered
before that.
This can lead to kernel crashes, so move everything in a single
lock/unlock section to prevent such races.
Fixes: b4a3d877dc ("media: ti: Add CSI2RX support for J721E")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When the source device is operating above 1.5 Gbps per lane, it needs to
send the Skew Calibration Sequence before sending any HS data. If the
DPHY is initialized after the source stream is started, then it might
miss the sequence and not be able to receive data properly. Move the
start of source subdev to the end of the sequence to make sure
everything is ready to receive data before the source starts streaming.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Fixes: 3295cf1241 ("media: cadence: Add support for external dphy")
Tested-by: Julien Massot <julien.massot@collabora.com>
Tested-by: Changhuang Liang <Changhuang.liang@starfivetech.com>
Reviewed-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Changhuang Liang <Changhuang.liang@starfivetech.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
First the media device node was created, and if successful it was
marked as 'registered'. This leaves a small race condition where
an application can open the device node and get an error back
because the 'registered' flag was not yet set.
Change the order: first set the 'registered' flag, then actually
register the media device node. If that fails, then clear the flag.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Fixes: cf4b9211b5 ("[media] media: Media device node support")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Absolute path to other DT schema is preferred over relative one.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Allow properties from video-interface-devices. This aligns the bindings
to sony,imx415.yaml. Changes inspired by commit e2e73ed46c ("media:
dt-bindings: sony,imx415: Allow props from video-interface-devices")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Support offloading of skbedit mark action.
For example, to mark with 0x0008, with dest ip 60.60.60.2 on eth2
interface:
# tc qdisc add dev eth2 ingress
# tc filter add dev eth2 ingress protocol ip flower \
dst_ip 60.60.60.2 action skbedit mark 0x0008 skip_sw
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
First problem is a double call to __in_dev_get_rcu(), because
the second one could return NULL.
if (__in_dev_get_rcu(dev) && __in_dev_get_rcu(dev)->ifa_list)
Second problem is a read from dev->ip6_ptr with no NULL check:
if (!list_empty(&rcu_dereference(dev->ip6_ptr)->addr_list))
Use the correct RCU API to fix these.
v2: add missing include <net/addrconf.h>
Fixes: d329ea5bd8 ("icmp: add response to RFC 8335 PROBE messages")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few strategic IS_ENABLED statements to let the compiler eliminate
unused code when CONFIG_XFS_SUPPORT_V4 is disabled.
This saves multiple kilobytes of .text in my .config:
$ size xfs.o.*
text data bss dec hex filename
1363633 294836 592 1659061 1950b5 xfs.o.new
1371453 294868 592 1666913 196f61 xfs.o.old
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
DisplayID spec v1.3 revision history notes do claim that
the toplogy block was added in v1.3 so requiring structure
v1.2 would seem correct, but there is at least one EDID in
edid.tv with a topology block and structure v1.0. And
there are also EDIDs with DisplayID structure v1.3 which
seems to be totally incorrect as DisplayID spec v1.3 lists
structure v1.2 as the only legal value.
Unfortunately I couldn't find copies of DisplayID spec
v1.0-v1.2 anywhere (even on vesa.org), so I'll have to
go on empirical evidence alone.
We used to parse the topology block on all v1.x
structures until the check for structure v2.0 was added.
Let's go back to doing that as the evidence does suggest
that there are DisplayIDs in the wild that would miss
out on the topology stuff otherwise.
Also toss out DISPLAY_ID_STRUCTURE_VER_12 entirely as
it doesn't appear we can really use it for anything.
I *think* we could technically skip all the structure
version checks as the block tags shouldn't conflict
between v2.0 and v1.x. But no harm in having a bit of
extra sanity checks I guess.
So far I'm not aware of any user reported regressions
from overly strict check, but I do know that it broke
igt/kms_tiled_display's fake DisplayID as that one
gets generated with structure v1.0.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Fixes: c5a486af9d ("drm/edid: parse Tiled Display Topology Data Block for DisplayID 2.0")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240410180139.21352-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
