[ Upstream commit ab3fde32af ]
The ETMv3 driver shares the same issue as ETMv4 regarding race
conditions when accessing the device mode.
This commit applies the same fix: ensuring that the device mode is
modified only by the target CPU to eliminate race conditions across
CPUs.
Fixes: 22fd532eaa ("coresight: etm3x: adding operation mode for etm_enable()")
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20251111-arm_coresight_power_management_fix-v6-3-f55553b6c8b3@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28eee21585 ]
When enabling a tracer via SysFS interface, the device mode may be set
by any CPU - not necessarily the target CPU. This can lead to race
condition in SMP, and may result in incorrect mode values being read.
Consider the following example, where CPU0 attempts to enable the tracer
on CPU1 (the target CPU):
CPU0 CPU1
etm4_enable()
` coresight_take_mode(SYSFS)
` etm4_enable_sysfs()
` smp_call_function_single() ----> etm4_enable_hw_smp_call()
/
/ CPU idle:
/ etm4_cpu_save()
/ ` coresight_get_mode()
Failed to enable h/w / ^^^
` coresight_set_mode(DISABLED) <-' Read the intermediate SYSFS mode
In this case, CPU0 initiates the operation by taking the SYSFS mode to
avoid conflicts with the Perf mode. It then sends an IPI to CPU1 to
configure the tracer registers. If any error occurs during this process,
CPU0 rolls back by setting the mode to DISABLED.
However, if CPU1 enters an idle state during this time, it might read
the intermediate SYSFS mode. As a result, the CPU PM flow could wrongly
save and restore tracer context that is actually disabled.
To resolve the issue, this commit moves the device mode setting logic on
the target CPU. This ensures that the device mode is only modified by
the target CPU, eliminating race condition between mode writes and reads
across CPUs.
An additional change introduces the etm4_disable_sysfs_smp_call()
function for SMP calls, which disables the tracer and explicitly set the
mode to DISABLED during SysFS operations. Rename
etm4_disable_hw_smp_call() to etm4_disable_sysfs_smp_call() for naming
consistency.
The flow is updated with this change:
CPU0 CPU1
etm4_enable()
` etm4_enable_sysfs()
` smp_call_function_single() ----> etm4_enable_hw_smp_call()
` coresight_take_mode(SYSFS)
Failed, set back to DISABLED
` coresight_set_mode(DISABLED)
CPU idle:
etm4_cpu_save()
` coresight_get_mode()
^^^
Read out the DISABLED mode
Fixes: c38a9ec2b2 ("coresight: etm4x: moving etm_drvdata::enable to atomic field")
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: mike Leach <mike.leach@linaro.org>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20251111-arm_coresight_power_management_fix-v6-2-f55553b6c8b3@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 693d1eaca9 ]
The device mode is defined as local type. This type cannot promise
SMP-safe access.
Change to atomic type and impose relax ordering, which ensures the
SMP-safe synchronisation and the ordering between the mode setting and
relevant operations.
Fixes: 22fd532eaa ("coresight: etm3x: adding operation mode for etm_enable()")
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20251111-arm_coresight_power_management_fix-v6-1-f55553b6c8b3@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6c5f9454e ]
netdev ops must be called under instance lock or rtnl_lock, but
io_register_zcrx_ifq() isn't doing this for netdev_queue_get_dma_dev().
Fix this by taking the instance lock using netdev_get_by_index_lock().
Extended the instance lock section to include attaching a memory
provider. Could not move io_zcrx_create_area() outside, since the dmabuf
codepath IORING_ZCRX_AREA_DMABUF requires ifq->dev.
Fixes: 59b8b32ac8 ("io_uring/zcrx: add support for custom DMA devices")
Signed-off-by: David Wei <dw@davidwei.uk>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c07a491c1b ]
Need to call netdev_get_by_index_lock() from io_uring/zcrx.c, but it is
currently private to net. Export the function in linux/netdevice.h.
Signed-off-by: David Wei <dw@davidwei.uk>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: b6c5f9454e ("io_uring/zcrx: call netdev_queue_get_dma_dev() under instance lock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e88e86411 ]
In one of the error paths, the memory allocated for skb_rx is not freed.
Fix that by freeing it before returning.
Fixes: a910e4a94f ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Link: https://patch.msgid.link/20251110175316.106591-1-nihaal@cse.iitm.ac.in
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10e1c77c36 ]
Commit b96bae3ae2 ("powerpc/32: Replace ASM exception exit by C
exception exit from ppc64") erroneouly copied to powerpc/32 the logic
from powerpc/64 based on feature CPU_FTR_STCX_CHECKS_ADDRESS which is
always 0 on powerpc/32.
Re-instate the logic implemented by commit b64f87c16f ("[POWERPC]
Avoid unpaired stwcx. on some processors") which is based on
CPU_FTR_NEED_PAIRED_STWCX feature.
Fixes: b96bae3ae2 ("powerpc/32: Replace ASM exception exit by C exception exit from ppc64")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/6040b5dbcf5cdaa1cd919fcf0790f12974ea6e5a.1757666244.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7afe2383ef ]
The elfcorehdr segment in the kdump image stores information about the
memory regions (called crash memory ranges) that the kdump kernel must
capture.
When a memory hot-remove event occurs, the kernel regenerates the
elfcorehdr for the currently loaded kdump image to remove the
hot-removed memory from the crash memory ranges.
Call chain:
remove_mem_range()
update_crash_elfcorehdr()
arch_crash_handle_hotplug_event()
crash_handle_hotplug_event()
While removing the hot-removed memory from the crash memory ranges in
remove_mem_range(), if the removed memory lies within an existing crash
range, that range is split into two. During this split, the size of the
second range was being calculated incorrectly.
This leads to dump capture failure with makedumpfile with below error:
$ makedumpfile -l -d 31 /proc/vmcore /tmp/vmcore
readpage_elf: Attempt to read non-existent page at 0xbbdab0000.
readmem: type_addr: 0, addr:c000000bbdab7f00, size:16
validate_mem_section: Can't read mem_section array.
readpage_elf: Attempt to read non-existent page at 0xbbdab0000.
readmem: type_addr: 0, addr:c000000bbdab7f00, size:8
get_mm_sparsemem: Can't get the address of mem_section.
The updated crash memory range in PT_LOAD entry is holding incorrect
data (checkout FileSiz and MemSiz):
readelf -a /proc/vmcore
<snip...>
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000b013d0000 0xc000000b80000000 0x0000000b80000000
0xffffffffc0000000 0xffffffffc0000000 RWE 0x0
<snip...>
Update the size calculation for the new crash memory range to fix this
issue.
Note: This problem will not occur if the kdump kernel is loaded or
reloaded after a memory hot-remove operation.
Fixes: 849599b702 ("powerpc/crash: add crash memory hotplug support")
Reported-by: Shirisha G <shirisha@linux.ibm.com>
Signed-off-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20251105033941.1752287-1-sourabhjain@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb31fef0d0 ]
amd_pstate_change_mode_without_dvr_change() calls cppc_set_auto_sel()
for all the present CPUs.
However, this callpath eventually calls cppc_set_reg_val() which
accesses the per-cpu cpc_desc_ptr object. This object is initialized
only for online CPUs via acpi_soft_cpu_online() -->
__acpi_processor_start() --> acpi_cppc_processor_probe().
Hence, restrict calling cppc_set_auto_sel() to only the online CPUs.
Fixes: 3ca7bc818d ("cpufreq: amd-pstate: Add guided mode control support via sysfs")
Suggested-by: Mario Limonciello (AMD) (kernel.org) <superm1@kernel.org>
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 381a3ce1c0 ]
IO operations may be needed before md_run(), such as updating metadata
after writing sysfs. Without bioset, this triggers a NULL pointer
dereference as below:
BUG: kernel NULL pointer dereference, address: 0000000000000020
Call Trace:
md_update_sb+0x658/0xe00
new_level_store+0xc5/0x120
md_attr_store+0xc9/0x1e0
sysfs_kf_write+0x6f/0xa0
kernfs_fop_write_iter+0x141/0x2a0
vfs_write+0x1fc/0x5a0
ksys_write+0x79/0x180
__x64_sys_write+0x1d/0x30
x64_sys_call+0x2818/0x2880
do_syscall_64+0xa9/0x580
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Reproducer
```
mdadm -CR /dev/md0 -l1 -n2 /dev/sd[cd]
echo inactive > /sys/block/md0/md/array_state
echo 10 > /sys/block/md0/md/new_level
```
mddev_init() can only be called once per mddev, no need to test if bioset
has been initialized anymore.
Link: https://lore.kernel.org/linux-raid/20251103125757.1405796-3-linan666@huaweicloud.com
Fixes: d981ed8419 ("md: Add new_level sysfs interface")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ce112d917 ]
'md_redundancy_group' are created in md_run() and deleted in del_gendisk(),
but these are not paired. Writing inactive/active to sysfs array_state can
trigger md_run() multiple times without del_gendisk(), leading to
duplicate creation as below:
sysfs: cannot create duplicate filename '/devices/virtual/block/md0/md/sync_action'
Call Trace:
dump_stack_lvl+0x9f/0x120
dump_stack+0x14/0x20
sysfs_warn_dup+0x96/0xc0
sysfs_add_file_mode_ns+0x19c/0x1b0
internal_create_group+0x213/0x830
sysfs_create_group+0x17/0x20
md_run+0x856/0xe60
? __x64_sys_openat+0x23/0x30
do_md_run+0x26/0x1d0
array_state_store+0x559/0x760
md_attr_store+0xc9/0x1e0
sysfs_kf_write+0x6f/0xa0
kernfs_fop_write_iter+0x141/0x2a0
vfs_write+0x1fc/0x5a0
ksys_write+0x79/0x180
__x64_sys_write+0x1d/0x30
x64_sys_call+0x2818/0x2880
do_syscall_64+0xa9/0x580
entry_SYSCALL_64_after_hwframe+0x4b/0x53
md: cannot register extra attributes for md0
Creation of it depends on 'pers', its lifecycle cannot be aligned with
gendisk. So fix this issue by triggering 'md_redundancy_group' deletion
when the array is becoming inactive.
Link: https://lore.kernel.org/linux-raid/20251103125757.1405796-2-linan666@huaweicloud.com
Fixes: 790abe4d77 ("md: remove/add redundancy group only in level change")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d794b499f9 ]
The function ufshcd_read_string_desc() was duplicating memory starting
from the beginning of struct uc_string_id, which included the length and
type fields. As a result, the allocated buffer contained unwanted
metadata in addition to the string itself.
The correct behavior is to duplicate only the Unicode character array in
the structure. Update the code so that only the actual string content is
copied into the new buffer.
Fixes: 5f57704dbc ("scsi: ufs: Use kmemdup in ufshcd_read_string_desc()")
Reviewed-by: Avri Altman <avri.altman@sandisk.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://patch.msgid.link/20251107230518.4060231-3-beanhuo@iokpp.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4492d54d59 ]
This commit addresses a memleak issue of panthor_vma (or drm_gpuva)
structure in Panthor driver, that can happen if the GPU page table
update operation to map the pages fail.
The issue is very unlikely to occur in practice.
v2: Add panthor_vm_op_ctx_return_vma() helper (Boris)
v3: Add WARN_ON_ONCE (Boris)
Fixes: 647810ec24 ("drm/panthor: Add the MMU/VM logical block")
Signed-off-by: Akash Goel <akash.goel@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patch.msgid.link/20251021081042.1377406-1-akash.goel@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be99c62ac7 ]
After setting the inode mode of $Extend to a regular file, executing the
truncate system call will enter the do_truncate() routine, causing the
run_lock uninitialized error reported by syzbot.
Prior to patch 4e8011ffec, if the inode mode of $Extend was not set to
a regular file, the do_truncate() routine would not be entered.
Add the run_lock initialization when loading $Extend.
syzbot reported:
INFO: trying to register non-static key.
Call Trace:
dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120
assign_lock_key+0x133/0x150 kernel/locking/lockdep.c:984
register_lock_class+0x105/0x320 kernel/locking/lockdep.c:1299
__lock_acquire+0x99/0xd20 kernel/locking/lockdep.c:5112
lock_acquire+0x120/0x360 kernel/locking/lockdep.c:5868
down_write+0x96/0x1f0 kernel/locking/rwsem.c:1590
ntfs_set_size+0x140/0x200 fs/ntfs3/inode.c:860
ntfs_extend+0x1d9/0x970 fs/ntfs3/file.c:387
ntfs_setattr+0x2e8/0xbe0 fs/ntfs3/file.c:808
Fixes: 4e8011ffec ("ntfs3: pretend $Extend records as regular files")
Reported-by: syzbot+bdeb22a4b9a09ab9aa45@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=bdeb22a4b9a09ab9aa45
Tested-by: syzbot+bdeb22a4b9a09ab9aa45@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaa5abcc9d ]
The handle is essential for retrieving the AUX_EVENT of each CPU and is
required in perf mode. It has been added to the coresight_path so that
dependent devices can access it from the path when needed.
The existing bug can be reproduced with:
perf record -e cs_etm//k -C 0-9 dd if=/dev/zero of=/dev/null
Showing an oops as follows:
Unable to handle kernel paging request at virtual address 000f6e84934ed19e
Call trace:
tmc_etr_get_buffer+0x30/0x80 [coresight_tmc] (P)
catu_enable_hw+0xbc/0x3d0 [coresight_catu]
catu_enable+0x70/0xe0 [coresight_catu]
coresight_enable_path+0xb0/0x258 [coresight]
Fixes: 080ee83cc3 ("Coresight: Change functions to accept the coresight_path")
Signed-off-by: Carl Worth <carl@os.amperecomputing.com>
Reviewed-by: Leo Yan <leo.yan@arm.com>
Co-developed-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250925-fix_helper_data-v2-1-edd8a07c1646@oss.qualcomm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e40b061cd3 ]
Move st,adc-freq, st,mod-12b, st,ref-sel, and st,sample-time properties
from the touchscreen subnode to the parent touch@44 node. These properties
are defined in the st,stmpe.yaml schema for the parent node, not the
touchscreen subnode, resolving the validation error about unevaluated
properties.
Fixes: 27538a18a4 ("ARM: dts: stm32: add STM32MP1-based Phytec SoM")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Link: https://lore.kernel.org/r/20250915224611.169980-1-jihed.chaibi.dev@gmail.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a338d6e849 ]
After device_initialize() is called, use put_device() to release the
device according to kernel device management rules. While direct
kfree() work in this case, using put_device() is more correct.
Found by code review.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Link: https://patch.msgid.link/20251110005158.13394-1-make24@iscas.ac.cn
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4813dea9e2 ]
Binding incorrectly specifies the 'DBI' region as 'ELBI'. DBI is a must
have region for DWC controllers as it has the Root Port and controller
specific registers, while ELBI has optional registers.
Hence, fix the binding. Though this is an ABI break, this change is needed
to accurately describe the PCI memory map.
Fixes: 7cd2103911 ("dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20251101-pci-meson-fix-v1-1-c50dcc56ed6a@oss.qualcomm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02f86101e4 ]
The bmi270 can be connected to I2C or a SPI interface. If it is a SPI,
during probe, if devm_regmap_init() fails, it should print the "spi"
term rather "i2c".
Fixes: 92cc50a005 ("iio: imu: bmi270: Add spi driver for bmi270 imu")
Signed-off-by: Rodrigo Gobbi <rodrigo.gobbi.7@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 495df2da69 ]
The MOST I2C driver has been completely broken for five years without
anyone noticing so remove the driver from staging.
Specifically, commit 723de0f917 ("staging: most: remove device from
interface structure") started requiring drivers to set the interface
device pointer before registration, but the I2C driver was never updated
which results in a NULL pointer dereference if anyone ever tries to
probe it.
Fixes: 723de0f917 ("staging: most: remove device from interface structure")
Cc: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20251029093442.29256-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b518e86d1a ]
Correct possible race conditions during device removal.
Previously, a scheduled work item to reset a LUN could still execute
after the device was removed, leading to use-after-free and other
resource access issues.
This race condition occurs because the abort handler may schedule a LUN
reset concurrently with device removal via sdev_destroy(), leading to
use-after-free and improper access to freed resources.
- Check in the device reset handler if the device is still present in
the controller's SCSI device list before running; if not, the reset
is skipped.
- Cancel any pending TMF work that has not started in sdev_destroy().
- Ensure device freeing in sdev_destroy() is done while holding the
LUN reset mutex to avoid races with ongoing resets.
Fixes: 2d80f4054f ("scsi: smartpqi: Update deleting a LUN via sysfs")
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Signed-off-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://patch.msgid.link/20251106163823.786828-3-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20da637eb5 ]
In stex_probe(), register_reboot_notifier() is called at the beginning,
but if any subsequent initialization step fails, the function returns
without unregistering the notifier, resulting in a resource leak.
Add unregister_reboot_notifier() in the out_disable error path to ensure
proper cleanup on all failure paths.
Fixes: 61b745fa63 ("scsi: stex: Add S6 support")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20251104094847.270-1-vulab@iscas.ac.cn
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9517b82d8d ]
There is one uaf issue in recv_work when running NBD_CLEAR_SOCK and
NBD_CMD_RECONFIGURE:
nbd_genl_connect // conf_ref=2 (connect and recv_work A)
nbd_open // conf_ref=3
recv_work A done // conf_ref=2
NBD_CLEAR_SOCK // conf_ref=1
nbd_genl_reconfigure // conf_ref=2 (trigger recv_work B)
close nbd // conf_ref=1
recv_work B
config_put // conf_ref=0
atomic_dec(&config->recv_threads); -> UAF
Or only running NBD_CLEAR_SOCK:
nbd_genl_connect // conf_ref=2
nbd_open // conf_ref=3
NBD_CLEAR_SOCK // conf_ref=2
close nbd
nbd_release
config_put // conf_ref=1
recv_work
config_put // conf_ref=0
atomic_dec(&config->recv_threads); -> UAF
Commit 87aac3a80a ("nbd: call nbd_config_put() before notifying the
waiter") moved nbd_config_put() to run before waking up the waiter in
recv_work, in order to ensure that nbd_start_device_ioctl() would not
be woken up while nbd->task_recv was still uncleared.
However, in nbd_start_device_ioctl(), after being woken up it explicitly
calls flush_workqueue() to make sure all current works are finished.
Therefore, there is no need to move the config put ahead of the wakeup.
Move nbd_config_put() to the end of recv_work, so that the reference is
held for the whole lifetime of the worker thread. This makes sure the
config cannot be freed while recv_work is still running, even if clear
+ reconfigure interleave.
In addition, we don't need to worry about recv_work dropping the last
nbd_put (which causes deadlock):
path A (netlink with NBD_CFLAG_DESTROY_ON_DISCONNECT):
connect // nbd_refs=1 (trigger recv_work)
open nbd // nbd_refs=2
NBD_CLEAR_SOCK
close nbd
nbd_release
nbd_disconnect_and_put
flush_workqueue // recv_work done
nbd_config_put
nbd_put // nbd_refs=1
nbd_put // nbd_refs=0
queue_work
path B (netlink without NBD_CFLAG_DESTROY_ON_DISCONNECT):
connect // nbd_refs=2 (trigger recv_work)
open nbd // nbd_refs=3
NBD_CLEAR_SOCK // conf_refs=2
close nbd
nbd_release
nbd_config_put // conf_refs=1
nbd_put // nbd_refs=2
recv_work done // conf_refs=0, nbd_refs=1
rmmod // nbd_refs=0
Reported-by: syzbot+56fbf4c7ddf65e95c7cc@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/6907edce.a70a0220.37351b.0014.GAE@google.com/T/
Fixes: 87aac3a80a ("nbd: make the config put is called before the notifying the waiter")
Depends-on: e2daec488c ("nbd: Fix hungtask when nbd_config_put")
Signed-off-by: Zheng Qixing <zhengqixing@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90e3bb44c0 ]
There is a uaf problem which is found by case 23rdev-lifetime:
Oops: general protection fault, probably for non-canonical address 0xdead000000000122
RIP: 0010:bdi_unregister+0x4b/0x170
Call Trace:
<TASK>
__del_gendisk+0x356/0x3e0
mddev_unlock+0x351/0x360
rdev_attr_store+0x217/0x280
kernfs_fop_write_iter+0x14a/0x210
vfs_write+0x29e/0x550
ksys_write+0x74/0xf0
do_syscall_64+0xbb/0x380
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7ff5250a177e
The sequence is:
1. rdev remove path gets reconfig_mutex
2. rdev remove path release reconfig_mutex in mddev_unlock
3. md stop calls do_md_stop and sets MD_DELETED
4. rdev remove path calls del_gendisk because MD_DELETED is set
5. md stop path release reconfig_mutex and calls del_gendisk again
So there is a race condition we should resolve. This patch adds a
flag MD_DO_DELETE to avoid the race condition.
Link: https://lore.kernel.org/linux-raid/20251029063419.21700-1-xni@redhat.com
Fixes: 9e59d60976 ("md: call del_gendisk in control path")
Signed-off-by: Xiao Ni <xni@redhat.com>
Suggested-by: Yu Kuai <yukuai@fnnas.com>
Reviewed-by: Li Nan <linan122@huawei.com>
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dc7620554 ]
We attempted to use RCU to protect the pointer 'thread', but directly
passed the value when calling md_wakeup_thread(). This means that the
RCU pointer has been acquired before rcu_read_lock(), which renders
rcu_read_lock() ineffective and could lead to a use-after-free.
Link: https://lore.kernel.org/linux-raid/20251015083227.1079009-1-yun.zhou@windriver.com
Fixes: 4469315439 ("md: protect md_thread with rcu")
Signed-off-by: Yun Zhou <yun.zhou@windriver.com>
Reviewed-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai@fnnas.com>
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc394b94dc ]
In sync del gendisk path, it deletes gendisk first and the directory
/sys/block/md is removed. Then it releases mddev kobj in a delayed work.
If we enable debug log in sysfs_remove_group, we can see the debug log
'sysfs group bitmap not found for kobject md'. It's the reason that the
parent kobj has been deleted, so it can't find parent directory.
In creating path, it allocs gendisk first, then adds mddev kobj. So it
should delete mddev kobj before deleting gendisk.
Before commit 9e59d60976 ("md: call del_gendisk in control path"), it
releases mddev kobj first. If the kobj hasn't been deleted, it does clean
job and deletes the kobj. Then it calls del_gendisk and releases gendisk
kobj. So it doesn't need to call kobject_del to delete mddev kobj. After
this patch, in sync del gendisk path, the sequence changes. So it needs
to call kobject_del to delete mddev kobj.
After this patch, the sequence is:
1. kobject del mddev kobj
2. del_gendisk deletes gendisk kobj
3. mddev_delayed_delete releases mddev kobj
4. md_kobj_release releases gendisk kobj
Link: https://lore.kernel.org/linux-raid/20250928012424.61370-1-xni@redhat.com
Fixes: 9e59d60976 ("md: call del_gendisk in control path")
Signed-off-by: Xiao Ni <xni@redhat.com>
Reviewed-by: Li Nan <linan122@huawei.com>
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb1ebb1046 ]
For 'always-on' and 'boot-on' regulators, the set_machine_constraints()
may enable supply before enabling the main regulator, however if the
latter fails, the function returns with an error but the supply remains
enabled.
When this happens, the regulator_register() function continues on the
error path where it puts the supply regulator. Since enabling the supply
is not balanced with a disable call, a warning similar to the following
gets issued from _regulator_put():
[ 1.603889] WARNING: CPU: 2 PID: 44 at _regulator_put+0x8c/0xa0
[ 1.603908] Modules linked in:
[ 1.603926] CPU: 2 UID: 0 PID: 44 Comm: kworker/u16:3 Not tainted 6.18.0-rc4 #0 NONE
[ 1.603938] Hardware name: Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C7 (DT)
[ 1.603945] Workqueue: async async_run_entry_fn
[ 1.603958] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 1.603967] pc : _regulator_put+0x8c/0xa0
[ 1.603976] lr : _regulator_put+0x7c/0xa0
...
[ 1.604140] Call trace:
[ 1.604145] _regulator_put+0x8c/0xa0 (P)
[ 1.604156] regulator_register+0x2ec/0xbf0
[ 1.604166] devm_regulator_register+0x60/0xb0
[ 1.604178] rpm_reg_probe+0x120/0x208
[ 1.604187] platform_probe+0x64/0xa8
...
In order to avoid this, change the set_machine_constraints() function to
disable the supply if enabling the main regulator fails.
Fixes: 05f224ca66 ("regulator: core: Clean enabling always-on regulators + their supplies")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20251107-regulator-disable-supply-v1-1-c95f0536f1b5@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e4e355ae7 ]
current large PEBS flag check only checks if sample_regs_user contains
unsupported GPRs but doesn't check if sample_regs_intr contains
unsupported GPRs.
Of course, currently PEBS HW supports to sample all perf supported GPRs,
the missed check doesn't cause real issue. But it won't be true any more
after the subsequent patches support to sample SSP register. SSP
sampling is not supported by adaptive PEBS HW and it would be supported
until arch-PEBS HW. So correct this issue.
Fixes: a47ba4d77e ("perf/x86: Enable free running PEBS for REGS_USER/INTR")
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251029102136.61364-5-dapeng1.mi@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e772a93eb ]
When intel_pmu_drain_pebs_icl() is called to drain PEBS records, the
perf_event_overflow() could be called to process the last PEBS record.
While perf_event_overflow() could trigger the interrupt throttle and
stop all events of the group, like what the below call-chain shows.
perf_event_overflow()
-> __perf_event_overflow()
->__perf_event_account_interrupt()
-> perf_event_throttle_group()
-> perf_event_throttle()
-> event->pmu->stop()
-> x86_pmu_stop()
The side effect of stopping the events is that all corresponding event
pointers in cpuc->events[] array are cleared to NULL.
Assume there are two PEBS events (event a and event b) in a group. When
intel_pmu_drain_pebs_icl() calls perf_event_overflow() to process the
last PEBS record of PEBS event a, interrupt throttle is triggered and
all pointers of event a and event b are cleared to NULL. Then
intel_pmu_drain_pebs_icl() tries to process the last PEBS record of
event b and encounters NULL pointer access.
To avoid this issue, move cpuc->events[] clearing from x86_pmu_stop()
to x86_pmu_del(). It's safe since cpuc->active_mask or
cpuc->pebs_enabled is always checked before access the event pointer
from cpuc->events[].
Closes: https://lore.kernel.org/oe-lkp/202507042103.a15d2923-lkp@intel.com
Fixes: 9734e25fbf ("perf: Fix the throttle logic for a group")
Reported-by: kernel test robot <oliver.sang@intel.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251029102136.61364-3-dapeng1.mi@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93e197e524 ]
IORING_SETUP_NO_MMAP rings remain user accessible even before the ctx
setup is finalised, so use WRITE_ONCE consistently when initialising
rings.
Fixes: 03d89a2de2 ("io_uring: support for user allocated memory for rings/sqes")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbf90d1b69 ]
The Radxa ROCK 5B+/5T USB Type-C port supports Dual Role Data and
should also act as a host. However, currently, when acting as a host,
only self-powered devices work.
Since the ROCK 5B+ supports Dual Role Power, set the power-role
property to "dual" and the try-power-role property to "sink". (along
with related properties)
The ROCK 5T should only support the "source" power-role.
This allows the port to act as a host, supply power to the port, and
allow bus-powered devices to work.
Note that on the ROCK 5T, with this patch applied, it has been
observed that some bus-powered devices do not work correctly. Also,
it has been observed that after connecting a device (and the data-role
switches to host), connecting a host device does not switch the
data-role back to the device role. These issues should be addressed
separately.
Note that there is a separate known issue where USB 3.0 SuperSpeed
devices do not work when oriented in reverse. This issue should also be
addressed separately. (USB 2.0/1.1 devices work in both orientations)
Fixes: 67b2c15d8f ("arm64: dts: rockchip: add USB-C support for ROCK 5B/5B+/5T")
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://patch.msgid.link/20251104085227.820-1-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c105e76bb1 ]
This code calls hfs_bnode_put(node) which drops the refcount and then
dreferences "node" on the next line. It's only safe to use "node"
when we're holding a reference so flip these two lines around.
Fixes: a06ec283e1 ("hfs: add logic of correcting a next unused CNID")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Viacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
Link: https://lore.kernel.org/r/aN-Xw8KnbSnuIcLk@stanley.mountain
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dea9f84776 ]
Currently, dma_fence_put(job->fence) is called in job notification
callback. However, if a job is canceled, the notification callback is never
invoked, leading to a memory leak. Move dma_fence_put(job->fence)
to the job cleanup function to ensure the fence is always released.
Fixes: aac243092b ("accel/amdxdna: Add command execution")
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20251105194140.1004314-1-lizhi.hou@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2e5a3cea4 ]
The move extent operation should return -EOPNOTSUPP if any of the inodes
is a quota inode, rather than requiring both to be quota inodes.
Fixes: 02749a4c20 ("ext4: add ext4_is_quota_file()")
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-ID: <20251013015128.499308-2-yi.zhang@huaweicloud.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2977567b24 ]
Currently, for beacon_stats, ath12k_mac_get_fw_stats() is called
for each started BSS on the specified hardware.
ath12k_mac_get_fw_stats() will wait for the fw_stats_done completion
after fetching the requested data from firmware. For the beacon_stats,
fw_stats_done completion will be set only when stats are received for
all BSSes. However, for other stats like vdev_stats or pdev_stats, there
is one request to the firmware for all enabled BSSes. Since beacon_stats
is fetched individually for all BSSes enabled in that pdev, waiting for
the completion event results in a timeout error when multiple BSSes are
enabled.
Avoid this by completing the fw_stats_done immediately after
updating the requested BSS's beacon stats in the list. Subsequently,
this list will be used to display the beacon stats for all enabled
BSSes in the requested pdev.
Additionally, remove 'num_bcn_recvd' from the ath12k_fw_stats struct
as it is no longer needed.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 9fe4669ae9 ("wifi: ath12k: Request beacon stats from firmware")
Signed-off-by: Manish Dharanenthiran <manish.dharanenthiran@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251031-beacon_stats-v1-2-f52fce7b03ac@qti.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b58acfd06 ]
When da9055_device_init() fails after regmap_add_irq_chip()
succeeds but mfd_add_devices() fails, the error handling path
only calls mfd_remove_devices() but forgets to call
regmap_del_irq_chip(). This results in a resource leak.
Fix this by adding regmap_del_irq_chip() to the error path so
that resources are released properly.
Fixes: 2896434cf2 ("mfd: DA9055 core driver")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20251010011737.1078-1-vulab@iscas.ac.cn
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7543818e97 ]
When there is an attempt to write data and RTW89_FLAG_UNPLUGGED is set,
this means device is disconnected and no urb is submitted. Return
appropriate error code to the caller to properly free the allocated
resources.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 2135c28be6 ("wifi: rtw89: Add usb.{c,h}")
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251104135720.321110-3-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28a4557528 ]
Allow adding rx_skb to rx_free_queue for later reuse on the common error
handling path, otherwise free it.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 2135c28be6 ("wifi: rtw89: Add usb.{c,h}")
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251104135720.321110-2-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e52b43883d ]
With CONFIG_CPUMASK_OFFSTACK=y, the 'bind_writers' buffer is allocated via
alloc_cpumask_var() in param_set_cpumask(). But it is not freed, when
setting the module parameter multiple times by sysfs interface or removing
module.
Below kmemleak trace is seen for this issue:
unreferenced object 0xffff888100aabff8 (size 8):
comm "bash", pid 323, jiffies 4295059233
hex dump (first 8 bytes):
07 00 00 00 00 00 00 00 ........
backtrace (crc ac50919):
__kmalloc_node_noprof+0x2e5/0x420
alloc_cpumask_var_node+0x1f/0x30
param_set_cpumask+0x26/0xb0 [locktorture]
param_attr_store+0x93/0x100
module_attr_store+0x1b/0x30
kernfs_fop_write_iter+0x114/0x1b0
vfs_write+0x300/0x410
ksys_write+0x60/0xd0
do_syscall_64+0xa4/0x260
entry_SYSCALL_64_after_hwframe+0x77/0x7f
This issue can be reproduced by:
insmod locktorture.ko bind_writers=1
rmmod locktorture
or:
insmod locktorture.ko bind_writers=1
echo 2 > /sys/module/locktorture/parameters/bind_writers
Considering that setting the module parameter 'bind_writers' or
'bind_readers' by sysfs interface has no real effect, set the parameter
permissions to 0444. To fix the memory leak when removing module, free
'bind_writers' and 'bind_readers' memory in lock_torture_cleanup().
Fixes: 73e3412424 ("locktorture: Add readers_bind and writers_bind module parameters")
Suggested-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Wang Liang <wangliang74@huawei.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8436112341 ]
When transitioning from 5-level to 4-level paging, the existing code
incorrectly accesses page table entries by directly dereferencing CR3 and
applying PAGE_MASK. This approach has several issues:
- __native_read_cr3() returns the raw CR3 register value, which on x86_64
includes not just the physical address but also flags Bits above the
physical address width of the system (i.e. above __PHYSICAL_MASK_SHIFT) are
also not masked.
- The pgd value is masked by PAGE_SIZE which doesn't take into account the
higher bits such as _PAGE_BIT_NOPTISHADOW.
Replace this with proper accessor functions:
- native_read_cr3_pa(): Uses CR3_ADDR_MASK to additionally mask metadata out
of CR3 (like SME or LAM bits). All remaining bits are real address bits or
reserved and must be 0.
- mask pgd value with PTE_PFN_MASK instead of PAGE_MASK, accounting for flags
above bit 51 (_PAGE_BIT_NOPTISHADOW in particular). Bits below 51, but above
the max physical address are reserved and must be 0.
Fixes: cb1c9e02b0 ("x86/efistub: Perform 4/5 level paging switch from the stub")
Reported-by: Michael van der Westhuizen <rmikey@meta.com>
Reported-by: Tobias Fleig <tfleig@meta.com>
Co-developed-by: Kiryl Shutsemau <kas@kernel.org>
Signed-off-by: Kiryl Shutsemau <kas@kernel.org>
Signed-off-by: Usama Arif <usamaarif642@gmail.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://patch.msgid.link/20251103141002.2280812-3-usamaarif642@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb22663125 ]
When transitioning from 5-level to 4-level paging, the existing code
incorrectly accesses page table entries by directly dereferencing CR3 and
applying PAGE_MASK. This approach has several issues:
- __native_read_cr3() returns the raw CR3 register value, which on x86_64
includes not just the physical address but also flags. Bits above the
physical address width of the system i.e. above __PHYSICAL_MASK_SHIFT) are
also not masked.
- The PGD entry is masked by PAGE_SIZE which doesn't take into account the
higher bits such as _PAGE_BIT_NOPTISHADOW.
Replace this with proper accessor functions:
- native_read_cr3_pa(): Uses CR3_ADDR_MASK to additionally mask metadata out
of CR3 (like SME or LAM bits). All remaining bits are real address bits or
reserved and must be 0.
- mask pgd value with PTE_PFN_MASK instead of PAGE_MASK, accounting for flags
above bit 51 (_PAGE_BIT_NOPTISHADOW in particular). Bits below 51, but above
the max physical address are reserved and must be 0.
Fixes: e9d0e6330e ("x86/boot/compressed/64: Prepare new top-level page table for trampoline")
Reported-by: Michael van der Westhuizen <rmikey@meta.com>
Reported-by: Tobias Fleig <tfleig@meta.com>
Co-developed-by: Kiryl Shutsemau <kas@kernel.org>
Signed-off-by: Kiryl Shutsemau <kas@kernel.org>
Signed-off-by: Usama Arif <usamaarif642@gmail.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/a482fd68-ce54-472d-8df1-33d6ac9f6bb5@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35501ac3c7 ]
When ETR is enabled as CS_MODE_SYSFS, if the buffer size is changed
and enabled again, currently sysfs_buf will point to the newly
allocated memory(buf_new) and free the old memory(buf_old). But the
etr_buf that is being used by the ETR remains pointed to buf_old, not
updated to buf_new. In this case, it will result in a memory
use-after-free issue.
Fix this by checking ETR's mode before updating and releasing buf_old,
if the mode is CS_MODE_SYSFS, then skip updating and releasing it.
Fixes: bd2767ec3d ("coresight: Fix run time warnings while reusing ETR buffer")
Signed-off-by: Xiaoqi Zhuang <xiaoqi.zhuang@oss.qualcomm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@arm.com>
Link: https://lore.kernel.org/r/20251021-fix_etr_issue-v3-1-99a2d066fee2@oss.qualcomm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21ef26d0e7 ]
When the PCIe controller is running in endpoint mode, the controller
initialization is triggered by a PERST# (PCIe reset) GPIO deassertion.
The driver has configured an IRQ to trigger when the PERST# GPIO changes
state. Without the pinctrl definition, we do not get an IRQ when PERST#
is deasserted, so the PCIe controller never gets initialized.
Add the missing definitions, so that the controller actually gets
initialized.
Fixes: ec142c44b0 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra234 DT")
Fixes: 0580286d0d ("arm64: tegra: Add Tegra234 PCIe C4 EP definition")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[treding@nvidia.com: add blank lines to separate blocks]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf76553aaa ]
Stephen reported that on KASAN builds he's seeing:
vmlinux.o: warning: objtool: user_exc_vmm_communication+0x15a: call to __kasan_check_read() leaves .noinstr.text section
vmlinux.o: warning: objtool: exc_debug_user+0x182: call to __kasan_check_read() leaves .noinstr.text section
vmlinux.o: warning: objtool: exc_int3+0x123: call to __kasan_check_read() leaves .noinstr.text section
vmlinux.o: warning: objtool: noist_exc_machine_check+0x17a: call to __kasan_check_read() leaves .noinstr.text section
vmlinux.o: warning: objtool: fred_exc_machine_check+0x17e: call to __kasan_check_read() leaves .noinstr.text section
This turns out to be atomic ops from unwind_reset_info() that have
explicit instrumentation. Place unwind_reset_info() in the preceding
instrumentation_begin() section.
Fixes: c6439bfaab ("Merge tag 'trace-deferred-unwind-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251105100014.GY4068168@noisy.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3862123e9b ]
The "ti,twl4030-power-n900" compatible string is obsolete and is not
supported by any in-kernel driver. Currently, the kernel falls back to
the second entry, "ti,twl4030-power-idle-osc-off", to bind a driver to
this node.
Make this fallback explicit by removing the obsolete board-specific
compatible. This preserves the existing functionality while making the
DTS compliant with the new, stricter 'ti,twl.yaml' binding.
Fixes: daebabd578 ("mfd: twl4030-power: Fix PM idle pin configuration to not conflict with regulators")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Link: https://lore.kernel.org/r/20250914192516.164629-4-jihed.chaibi.dev@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7f3bc1830 ]
The "ti,twl4030-power-beagleboard-xm" compatible string is obsolete and
is not supported by any in-kernel driver. Currently, the kernel falls
back to the second entry, "ti,twl4030-power-idle-osc-off", to bind a
driver to this node.
Make this fallback explicit by removing the obsolete board-specific
compatible. This preserves the existing functionality while making the
DTS compliant with the new, stricter 'ti,twl.yaml' binding.
Fixes: 9188883fd6 ("ARM: dts: Enable twl4030 off-idle configuration for selected omaps")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Link: https://lore.kernel.org/r/20250914192516.164629-3-jihed.chaibi.dev@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
