The potential TX stuck occurs when there are lots of packets to be
transmitted and the boundary of the tx_resource is hit. Add this
patch to avoid the TX stuck when burst traffic.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-6-pkshih@realtek.com
In STA mode, if peer is TDLS. Allocate a BSSID CAM entry with peer's
address to match address properly, and then hardware can ACK peer's
packets and receive packets to driver.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-4-pkshih@realtek.com
Normally, we allocate a BSSID CAM to a vif. By hardware design, we must
allocate a BSSID CAM to each TDLS peer, so separate BSSID CAM operations
that will be used by later patches.
This patch doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-3-pkshih@realtek.com
Normally, we only allocate an address CAM and single one MAC ID to AP in
STA mode. To support TDLS, we handle TDLS peers like AP handles stations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-2-pkshih@realtek.com
As a result of the execution of the inner while loop, the value
of 'idx' can be equal to LINK_QUAL_MAX_RETRY_NUM. However, this
is not checked after the loop and 'idx' is used to write the
LINK_QUAL_MAX_RETRY_NUM size array 'lq_cmd->rs_table[idx]' below
in the outer loop.
The fix is to check the new value of 'idx' inside the nested loop,
and break both loops if index equals the size. Checking it at the
start is now pointless, so let's remove it.
Detected using the static analysis tool - Svace.
Fixes: be663ab670 ("iwlwifi: split the drivers for agn and legacy devices 3945/4965")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608171614.28891-1-aleksei.kodanev@bell-sw.com
The MLO links used for connection with an MLD AP are decided by the
driver in case of SME offloaded to driver.
Add support for the drivers to indicate the information of links used
for MLO connection in connect and roam callbacks, update the connected
links information in wdev from connect/roam result sent by driver.
Also, send the connected links information to userspace.
Add a netlink flag attribute to indicate that userspace supports
handling of MLO connection. Drivers must not do MLO connection when this
flag is not set. This is to maintain backwards compatibility with older
supplicant versions which doesn't have support for MLO connection.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Print the link ID in link_info_changed function.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add initial support to hwsim for creating MLO-capable
radios dynamically (and statically via module parameter,
but that's not really recommended.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add to hwsim a link_data structure.
For now, move the beacon interval and beacon timer to
the link_data structure (making them per link).
Set a beacon timer for each link and transmit a per
link beacon (pass the link_id to ieee80211_beacon_get).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In start_ap and stop_ap mac80211 callbacks pass the link_id
to the drivers.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace the bss_info_changed callback with vif_cfg_changed
and link_info_changed callbacks (for vif changes and link
changes).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start making some SMPS related code MLD-aware. This isn't
really done yet, but again cuts down our 'deflink' reliance.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the channel context code MLO aware, along with some
functions that it uses, so that the chan.c file is now
MLD-clean and no longer uses deflink/bss_conf/etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.
So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.
For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.
Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid abusing the efivar layer by invoking it with locally constructed
efivar_entry instances, and instead, just call the EFI routines directly
if available.
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Using half of the efivar API with locally baked efivar_entry instances
is not the right way to use this API, and these uses impede planned work
on the efivar layer itself.
So switch to direct EFI variable store accesses: we don't need the
efivar layer anyway.
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
As per commit c4f135d643 ("workqueue: Wrap flush_workqueue() using
a macro") says, use per "struct ath6kl_usb" workqueue.
This is a blind conversion, and is only compile tested.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/f78ddbdc-8989-a1a7-2234-ce9ec3894625@I-love.SAKURA.ne.jp
I've changed *STAT_* macros a bit in previous patch and I seems like
they become really unreadable. Align these macros definitions to make
code cleaner and fix folllowing checkpatch warning
ERROR: Macros with complex values should be enclosed in parentheses
Also, statistics macros now accept an hif_dev as argument, since
macros that depend on having a local variable with a magic name
don't abide by the coding style.
No functional change
Suggested-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/ebb2306d06a496cd1b032155ae52fdc5fa8cc2c5.1655145743.git.paskripkin@gmail.com
Router interfaces (RIFs) constructed on top of VLAN-aware bridges are of
"VLAN" type, whereas RIFs constructed on top of VLAN-unaware bridges of
"FID" type.
In other words, the RIF type is derived from the underlying FID type.
VLAN RIFs are used on top of 802.1Q FIDs, whereas FID RIFs are used on
top of 802.1D FIDs.
Currently 802.1Q FIDs are emulated using 802.1D FIDs, and therefore VLAN
RIFs are emulated using FID RIFs.
As part of converting the driver to use unified bridge, 802.1Q FIDs and
VLAN RIFs will be used.
Add the relevant fields to RITR register, add pack() function for VLAN
RIF and rename one field to fit the internal name.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As preparation for unified bridge model, add support for VNI->FID mapping
via SVFA register.
When performing VXLAN encapsulation, the VXLAN header needs to contain a
VNI. This VNI is derived from the FID classification performed on
ingress, through which the ingress RIF is also determined.
Similarly, when performing VXLAN decapsulation, the FID of the packet
needs to be determined. This FID is derived from VNI classification
performed during decapsulation.
In the old model, both entries (i.e., FID->VNI and VNI->FID) were
configured via SFMR.vni.
In the new model, where ingress is separated from egress, ingress
configuration (VNI->FID) is performed via SVFA, while SFMR only
configures egress (FID->VNI).
Add 'vni' field to SVFA, add new mapping table - VNI to FID, add new
pack() function for VNI mapping and edit the comment in SFMR.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RITR configures the router interface table. As preparation for unified
bridge model, add egress FID field to RITR.
After routing, a packet has to perform a layer-2 lookup using the
destination MAC it got from the routing and a FID.
In the new model, the egress FID is configured by RITR for both sub-port
and FID RIFs.
Add 'efid' field to sub-port router interface and update FID router
interface related comment.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The REIV maps {egress router interface (eRIF), egress_port} -> {vlan ID}.
As preparation for unified bridge model, add REIV register for future use.
In the past, firmware would take care of the above mentioned mapping,
but in the new model this should be done by software using REIV register.
REIV register supports a simultaneous update of 256 ports using
'port_page' field. When 'port_page'=0 the records represent ports
0-255, when 'port_page'=1 the records represent ports 256-511 and so
on.
The register is reserved while using the legacy model.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFGC register maps {packet type, bridge type} -> {MID base, table type}.
As preparation for unified bridge model, remove 'mid' field and add
'mid_base' field.
The MID index (index to PGT table which maps MID to local port list and
SMPE index) is a result of 'mid_base' + 'fid_offset'. Using the legacy
bridge model, firmware configures 'mid_base'. However, using the new model,
software is responsible to configure it via SFGC register.
The 'mid_base' is configured per {packet type, bridge type}, for
example, for {Unicast, .1Q}, {Broadcast, .1D}.
Add the field 'mid_base' to SFGC register and increase the length of the
register accordingly.
Remove the field 'mid' as currently it is ignored by the device, its use
is an old leftover.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFMR register creates and configures FIDs. As preparation for unified
bridge model, add a required field for future use.
The PGT (Port Group) table maps multicast ID (MID) to
{local port list, SMPE index} on Spectrum-1 and to {local port list} on
the other ASICs.
In the legacy model, software did not interact with this table directly.
Instead, it was accessed by firmware in response to registers such as
SFTR and SMID.
In the new model, the SFTR register is deprecated and software has full
control over the PGT table using the SMID register.
The configuration of MDB entries (using SFD) is unchanged, but flooding
configuration is completely different.
SFGC register maps {packet type, bridge type} -> {MID base, table type},
then with FID and FID-offset which are configured via SFMR, the MID index
is obtained.
Add the field 'flood_bridge_type' to SFMR, software can separate between
802.1q FIDs and vFIDs using two types which are supported.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFD register configures FDB table. As preparation for unified bridge model,
add some required fields for future use.
In the new model, firmware no longer configures the egress VID, this
responsibility is moved to software. For layer 2 this means that software
needs to determine the egress VID for both unicast and multicast.
For unicast FDB records and unicast LAG FDB records, the VID needs to be
set via new fields in SFD - 'set_vid' and 'vid'.
Add the two mentioned fields for future use.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFMR register creates and configures FIDs. As preparation unified bridge
model, add some required fields for future use.
The device includes two main tables to support layer 2 multicast (i.e.,
MDB and flooding). These are the PGT (Port Group Table) and the
MPE (Multicast Port Egress) table.
- PGT is {MID -> (bitmap of local_port, SPME index)}
- MPE is {(Local port, SMPE index) -> eVID}
In Spectrum-2 and later ASICs, the SMPE index is an attribute of the FID
and programmed via new fields in SFMR register - 'smpe_valid' and 'smpe'.
Add the two mentioned fields for future use and increase the length of
the register accordingly.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMID register maps multicast ID (MID) into a list of local ports.
As preparation for unified bridge model, add some required fields for
future use.
The device includes two main tables to support layer 2 multicast (i.e.,
MDB and flooding). These are the PGT (Port Group Table) and the
MPE (Multicast Port Egress) table.
- PGT is {MID -> (bitmap of local_port, SPME index)}
- MPE is {(Local port, SMPE index) -> eVID}
In Spectrum-1, both indexes into the MPE table (local port and SMPE) are
derived from the PGT table. Therefore, the SMPE index needs to be
programmed as part of the PGT entry via new fields in SMID - 'smpe_valid'
and 'smpe'.
Add the two mentioned fields for future use and align the callers of
mlxsw_reg_smid2_pack() to pass zeros for SMPE fields.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMPE register maps {egress_port, SMPE index} -> VID.
The device includes two main tables to support layer 2 multicast (i.e.,
MDB and flooding). These are the PGT (Port Group Table) and the
MPE (Multicast Port Egress) table.
- PGT is {MID -> (bitmap of local_port, SPME index)}
- MPE is {(Local port, SMPE index) -> eVID}
In Spectrum-1, the index into the MPE table - called switch multicast to
port egress VID (SMPE) - is derived from the PGT entry, whereas in
Spectrum-2 and later ASICs it is derived from the FID.
In the legacy model, software did not interact with this table as it was
completely hidden in firmware. In the new model, software needs to
populate the table itself in order to map from {Local port, SMPE index} to
an egress VID. This is done using the SMPE register.
Add the register for future use.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SVFA register controls the VID to FID mapping and {Port, VID} to FID
mapping for virtualized ports. As preparation for unified bridge model,
add some required fields for future use.
On ingress, after ingress ACL, a packet needs to be classified to a FID.
The key for this lookup can be one of:
1. VID. When port is not in virtual mode.
2. {RQ, VID}. When port is in virtual mode.
3. FID. When FID was set by ingress ACL.
Since RITR no longer performs ingress configuration, the ingress RIF for
the first two entry types needs to be set via new fields in SVFA -
'irif_v' and 'irif'.
Add the two mentioned fields for future use and increase the length of
the register accordingly.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFMR register creates and configures FIDs. As preparation for unified
bridge model, add some required fields for future use.
On ingress, after ingress ACL, a packet needs to be classified to a FID.
The key for this lookup can be one of:
1. VID. When port is not in virtual mode.
2. {RQ, VID}. When port is in virtual mode.
3. FID. When FID was set by ingress ACL.
For example, via VR_AND_FID_ACTION.
Since RITR no longer performs ingress configuration, the ingress RIF for
the last entry type needs to be set via new fields in SFMR - 'irif_v'
and 'irif'.
Add the two mentioned fields for future use.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFMR register creates and configures FIDs. As preparation for unified
bridge model, add a field for future use.
In the new model, RITR no longer configures the rFID used for sub-port RIFs
and it has to be created by software via SFMR. Such FIDs need to be created
with special flood indication using 'flood_rsp' field. When set, this bit
instructs the device to manage the flooding entries for this FID in a
reserved part of the port group table (PGT).
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'Commit 6f91f4ba04 ("vmxnet3: add support for capability registers")'
added support for capability registers. These registers are used
to advertize capabilities of the device.
The patch updated the dev_caps to disable outer checksum offload if
PTCR register does not support it. However, it missed to update
other overlay offloads. This patch fixes this issue.
Fixes: 6f91f4ba04 ("vmxnet3: add support for capability registers")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 9386ebccfc ("nfp: update nfp_X logging definitions")
The reverted patch was intended to improve logging for the NFP driver by
including information such as the source code file and number in log
messages.
Unfortunately our experience is that this has not improved things as
we had hoped. The resulting logs are inconsistent with (most) other
kernel log messages. And rely on knowledge of the source code version
in order for the extra information to be useful.
Thus, revert the change.
We acknowledge that Jakub Kicinski <kuba@kernel.org> foresaw this problem.
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the newly introduced mii_bmcr_encode_fixed() for the xpcs driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the newly introduced mii_bmcr_encode_fixed() to get the
BMCR value when setting loopback mode for the 88e1510.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylib can make use of the newly introduced mii_bmcr_encode_fixed()
macro, so let's convert it over.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adjusting the PTP clock, the base time of the TAS configuration
will become unreliable. We need reset the TAS configuration by using a
new base time.
For example, if the driver gets a base time 0 of Qbv configuration from
user, and current time is 20000. The driver will set the TAS base time
to be 20000. After the PTP clock adjustment, the current time becomes
10000. If the TAS base time is still 20000, it will be a future time,
and TAS entry list will stop running. Another example, if the current
time becomes to be 10000000 after PTP clock adjust, a large time offset
can cause the hardware to hang.
This patch introduces a tas_clock_adjust() function to reset the TAS
module by using a new base time after the PTP clock adjustment. This can
avoid issues above.
Due to PTP clock adjustment can occur at any time, it may conflict with
the TAS configuration. We introduce a new TAS lock to serialize the
access to the TAS registers.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>