[ Upstream commit 84684c57c9 ]
Register offsets for v3 and v4 versions are backward compatible. Assign v3
offsets for v4 and all higher versions to avoid end up using v2 offsets.
Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250623-rsc_v4-v1-1-275b27bc5e3c@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b9c60e440 ]
When a USB4 dock is unplugged from a system it won't respond to ring
events. The PCI core handles the surprise removal event and notifies
all PCI drivers. The XHCI PCI driver sets a flag that the device is
being removed as well.
When that flag is set don't show messages in the cleanup path for
marking the controller dead.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250717073107.488599-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f72b9aa821 ]
There is a subtle contradiction between sections of the xHCI 1.2 spec
regarding the initialization of Input Endpoint Context fields. Section
4.8.2 ("Endpoint Context Initialization") states that all fields should
be initialized to 0. However, Section 6.2.3 ("Endpoint Context", p.453)
specifies that the Average TRB Length (avg_trb_len) field shall be
greater than 0, and explicitly notes (p.454): "Software shall set
Average TRB Length to '8' for control endpoints."
Strictly setting all fields to 0 during initialization conflicts with
the specific recommendation for control endpoints. In practice, setting
avg_trb_len = 0 is not meaningful for the hardware/firmware, as the
value is used for bandwidth calculation.
Motivation: Our company is developing a custom Virtual xHC hardware
platform that strictly follows the xHCI spec and its recommendations.
During validation, we observed that enumeration fails and a parameter
error (TRB Completion Code = 5) is reported if avg_trb_len for EP0 is
not set to 8 as recommended by Section 6.2.3. This demonstrates the
importance of assigning a meaningful, non-zero value to avg_trb_len,
even in virtualized or emulated environments.
This patch explicitly sets avg_trb_len to 8 for EP0 in
xhci_setup_addressable_virt_dev(), as recommended in Section 6.2.3, to
prevent potential issues with xHCI host controllers that enforce the
spec strictly.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220033
Signed-off-by: Jay Chen <shawn2000100@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250717073107.488599-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65fc0fc137 ]
When a USB4 dock is unplugged from a system it won't respond to ring
events. The PCI core handles the surprise removal event and notifies
all PCI drivers. The XHCI PCI driver sets a flag that the device is
being removed, and when the device stops responding a flag is also
added to indicate it's dying.
When that flag is set don't bother to show warnings about a missing
controller.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250717073107.488599-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af833e7f7d ]
ucsi_psy_get_current_max would return 0mA as the maximum current if
UCSI detected a BC or a Default USB Power sporce.
The comment in this function is true that we can't tell the difference
between DCP/CDP or SDP chargers, but we can guarantee that at least 1-unit
of USB 1.1/2.0 power is available, which is 100mA, which is a better
fallback value than 0, which causes some userspaces, including the ChromeOS
power manager, to regard this as a power source that is not providing
any power.
In reality, 100mA is guaranteed from all sources in these classes.
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Jameson Thies <jthies@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250717200805.3710473-1-bleung@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04850819c6 ]
The kernel does not provide sys_futex() on 32-bit architectures that do not
support 32-bit time representations, such as riscv32.
As a result, glibc cannot define SYS_futex, causing compilation failures in
tests that rely on this syscall. Define SYS_futex as SYS_futex_time64 in
such cases to ensure successful compilation and compatibility.
Signed-off-by: Cynthia Huang <cynthia@andestech.com>
Signed-off-by: Ben Zong-You Xie <ben717@andestech.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/all/20250710103630.3156130-1-ben717@andestech.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a1416a49e ]
AMU counters on certain CPPC-based platforms tend to yield inaccurate
delivered performance measurements on systems that are idle/mostly idle.
This results in an inaccurate frequency being stored by cpufreq in its
policy structure when the CPU is brought online. [1]
Consequently, if the userspace governor tries to set the frequency to a
new value, there is a possibility that it would be the erroneous value
stored earlier. In such a scenario, cpufreq would assume that the
requested frequency has already been set and return early, resulting in
the correct/new frequency request never making it to the hardware.
Since the operating frequency is liable to this sort of inconsistency,
mark the CPPC driver with CPUFREQ_NEED_UPDATE_LIMITS so that it is always
invoked when a target frequency update is requested.
Link: https://lore.kernel.org/linux-pm/20250619000925.415528-3-pmalani@google.com/ [1]
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Prashant Malani <pmalani@google.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://patch.msgid.link/20250722055611.130574-2-pmalani@google.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ff3aeb664 ]
The Lenovo Yoga 6 13ACL6 82ND has a similar BIOS problem as other Lenovo
laptops from that vintage that causes a rather long resume from suspend.
Add it to the quirk list that manipulates the scratch register to avoid
the issue.
Reported-by: Adam Berglund <adam.f.berglund@hotmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4434
Tested-by: Adam Berglund <adam.f.berglund@hotmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20250718172307.1928744-1-superm1@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7919407eca ]
When encounters some errors like these:
xhci_hcd 0000:4a:00.2: xHCI dying or halted, can't queue_command
xhci_hcd 0000:4a:00.2: FIXME: allocate a command ring segment
usb usb5-port6: couldn't allocate usb_device
It's hard to know whether xhc_state is dying or halted. So it's better
to print xhc_state's value which can help locate the resaon of the bug.
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20250725060117.1773770-1-suhui@nfschina.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9b13cdad8 ]
If a lookup in tracefs is done on a file that does not exist, it leaves a
dentry hanging around until memory pressure removes it. But eventfs
dentries should hang around as when their ref count goes to zero, it
requires more work to recreate it. For the rest of the tracefs dentries,
they hang around as their dentry is used as a descriptor for the tracing
system. But if a file lookup happens for a file in tracefs that does not
exist, it should be deleted.
Add a .d_delete callback that checks if dentry->fsdata is set or not. Only
eventfs dentries set fsdata so if it has content it should not be deleted
and should hang around in the cache.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27cd1bf124 ]
incidentally, securityfs_recursive_remove() is broken without that -
it leaks dentries, since simple_recursive_removal() does not expect
anything of that sort. It could be worked around by dput() in
remove_one() callback, but it's easier to just drop that double-get
stuff.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c58d42de7 ]
We used to need securityfs_remove() to undo simple_pin_fs() done when
the file had been created and to drop the second extra reference
taken at the same time. Now that neither is needed (or done by
securityfs_remove()), we can simply call simple_unlink() and be done
with that - the broken games with locking had been there only for the
sake of securityfs_remove().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a099b09a33 ]
Previously, ext2_fiemap would unconditionally apply "len = min_t(u64, len,
i_size_read(inode));", When inode->i_size was 0 (for an empty file), this
would reduce the requested len to 0. Passing len = 0 to iomap_fiemap could
then result in an -EINVAL error, even for valid queries on empty files.
Link: https://github.com/linux-test-project/ltp/issues/1246
Signed-off-by: Wei Gao <wegao@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250613152402.3432135-1-wegao@suse.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a1ad73aa1 ]
Similar to commit 1ed95281c0 ("anon_inode: raise SB_I_NODEV and SB_I_NOEXEC"):
it shouldn't be possible to execute pidfds via
execveat(fd_anon_inode, "", NULL, NULL, AT_EMPTY_PATH)
so raise SB_I_NOEXEC so that no one gets any creative ideas.
Also raise SB_I_NODEV as we don't expect or support any devices on pidfs.
Link: https://lore.kernel.org/20250618-work-pidfs-persistent-v2-1-98f3456fd552@kernel.org
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 413e800cad ]
Modify ata_scsi_lpm_store() to return an error if a user attempts to set
a link power management policy for a port that does not support LPM,
that is, ports flagged with ATA_FLAG_NO_LPM.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20250701125321.69496-6-dlemoal@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7870e8d34 ]
The AHCI specification version 1.3.1 section 8.3.1.4 (Software
Requirements and Precedence) states that:
If CAP.SSC or CAP.PSC is cleared to ‘0’, software should disable
device-initiated power management by issuing the appropriate SET
FEATURES command to the device.
To satisfy this constraint and force ata_dev_configure to disable the
device DIPM feature, modify ahci_update_initial_lpm_policy() to set the
ATA_FLAG_NO_DIPM flag on ports that have a host with either the
ATA_HOST_NO_PART flag set or the ATA_HOST_NO_SSC flag set.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de.>
Link: https://lore.kernel.org/r/20250701125321.69496-7-dlemoal@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65b2c92f69 ]
Commit fa997b0576 ("ata: ahci: Do not enable LPM if no LPM states are
supported by the HBA") introduced an early return in
ahci_update_initial_lpm_policy() to ensure that the target_lpm_policy
of ports belonging to a host that does not support the Partial, Slumber
and DevSleep power states is unchanged and remains set to
ATA_LPM_UNKNOWN and thus prevents the execution of
ata_eh_link_set_lpm().
However, a user or a system daemon (e.g. systemd-udevd) may still
attempt changing the LPM policy through the sysfs
link_power_management_policy of the host.
Improve this to prevent sysfs LPM policy changes by setting the flag
ATA_FLAG_NO_LPM for the port of such host, and initialize the port
target_lpm_policy to ATA_LPM_MAX_POWER to guarantee that no unsupported
low power state is being used on the port and its link.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250701125321.69496-9-dlemoal@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a8061ee5e ]
We want a class that nests outside of I_MUTEX_NORMAL (for the sake of
callbacks that might want to lock the victim) and inside I_MUTEX_PARENT
(so that a variant of that could be used with parent of the victim
held locked by the caller).
In reality, simple_recursive_removal()
* never holds two locks at once
* holds the lock on parent of dentry passed to callback
* is used only on the trees with fixed topology, so the depths
are not changing.
So the locking order is actually fine.
AFAICS, the best solution is to assign I_MUTEX_CHILD to the locks
grabbed by that thing.
Reported-by: syzbot+169de184e9defe7fe709@syzkaller.appspotmail.com
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00c9c9628b ]
With `two-primaries` enabled, DRBD tries to detect "concurrent" writes
and handle write conflicts, so that even if you write to the same sector
simultaneously on both nodes, they end up with the identical data once
the writes are completed.
In handling "superseeded" writes, we forgot a kref_get,
resulting in a premature drbd_destroy_device and use after free,
and further to kernel crashes with symptoms.
Relevance: No one should use DRBD as a random data generator, and apparently
all users of "two-primaries" handle concurrent writes correctly on layer up.
That is cluster file systems use some distributed lock manager,
and live migration in virtualization environments stops writes on one node
before starting writes on the other node.
Which means that other than for "test cases",
this code path is never taken in real life.
FYI, in DRBD 9, things are handled differently nowadays. We still detect
"write conflicts", but no longer try to be smart about them.
We decided to disconnect hard instead: upper layers must not submit concurrent
writes. If they do, that's their fault.
Signed-off-by: Sarah Newman <srn@prgmr.com>
Signed-off-by: Lars Ellenberg <lars@linbit.com>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20250627095728.800688-1-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a11201668 ]
Verify that number of partition maps isn't insanely high which can lead
to large allocation in udf_sb_alloc_partition_maps(). All partition maps
have to fit in the LVD which is in a single block.
Reported-by: syzbot+478f2c1a6f0f447a46bb@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e49538288 ]
Syzbot came up with a reproducer where a loop device block size is
changed underneath a mounted filesystem. This causes a mismatch between
the block device block size and the block size stored in the superblock
causing confusion in various places such as fs/buffer.c. The particular
issue triggered by syzbot was a warning in __getblk_slow() due to
requested buffer size not matching block device block size.
Fix the problem by getting exclusive hold of the loop device to change
its block size. This fails if somebody (such as filesystem) has already
an exclusive ownership of the block device and thus prevents modifying
the loop device under some exclusive owner which doesn't expect it.
Reported-by: syzbot+01ef7a8da81a975e1ccd@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Tested-by: syzbot+01ef7a8da81a975e1ccd@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20250711163202.19623-2-jack@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c8f12cf1e ]
Clears up the warning added in 7ee3647243 ("migrate: Remove call to
->writepage") that occurs in various xfstests, causing "something found
in dmesg" failures.
[ 341.136573] gfs2_meta_aops does not implement migrate_folio
[ 341.136953] WARNING: CPU: 1 PID: 36 at mm/migrate.c:944 move_to_new_folio+0x2f8/0x300
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 557c024ca7 ]
A fuzzer test introduced corruption that ends up with a depth of 0 in
dir_e_read(), causing an undefined shift by 32 at:
index = hash >> (32 - dip->i_depth);
As calculated in an open-coded way in dir_make_exhash(), the minimum
depth for an exhash directory is ilog2(sdp->sd_hash_ptrs) and 0 is
invalid as sdp->sd_hash_ptrs is fixed as sdp->bsize / 16 at mount time.
So we can avoid the undefined behaviour by checking for depth values
lower than the minimum in gfs2_dinode_in(). Values greater than the
maximum are already being checked for there.
Also switch the calculation in dir_make_exhash() to use ilog2() to
clarify how the depth is calculated.
Tested with the syzkaller repro.c and xfstests '-g quick'.
Reported-by: syzbot+4708579bb230a0582a57@syzkaller.appspotmail.com
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a58ac9bfc ]
Update the nvme_tcp_start_tls() function to use dev_err() instead of
dev_dbg() when a TLS error is detected. This ensures that handshake
failures are visible by default, aiding in debugging.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ef50c4c6a ]
Same as done for raid0, set chunk_sectors limit to appropriately set the
atomic write size limit.
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20250711105258.3135198-5-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fb9d4341b ]
Same as done for raid0, set chunk_sectors limit to appropriately set the
atomic write size limit.
Setting chunk_sectors limit in this way overrides the stacked limit
already calculated based on the bottom device limits. This is ok, as
when any bios are sent to the bottom devices, the block layer will still
respect the bottom device chunk_sectors.
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20250711105258.3135198-6-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b2c214a95 ]
NVMe devices from multiple vendors appear to get stuck in a reset state
that we can't get out of with an NVMe level Controller Reset. The kernel
would report these with messages that look like:
Device not ready; aborting reset, CSTS=0x1
These have historically required a power cycle to make them usable
again, but in many cases, a PCIe FLR is sufficient to restart operation
without a power cycle. Try it if the initial controller reset fails
during any nvme reset attempt.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Nitesh Shetty <nj.shetty@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5fc1400a3 ]
If smb2_create_link() is called with ReplaceIfExists set and the name
does exist then a deadlock will happen.
ksmbd_vfs_kern_path_locked() will return with success and the parent
directory will be locked. ksmbd_vfs_remove_file() will then remove the
file. ksmbd_vfs_link() will then be called while the parent is still
locked. It will try to lock the same parent and will deadlock.
This patch moves the ksmbd_vfs_kern_path_unlock() call to *before*
ksmbd_vfs_link() and then simplifies the code, removing the file_present
flag variable.
Signed-off-by: NeilBrown <neil@brown.name>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e0546eabc ]
The Linux IMA (Integrity Measurement Architecture) subsystem used for
secure boot, file integrity, or remote attestation cannot be a loadable
module for few reasons listed below:
o Boot-Time Integrity: IMA’s main role is to measure and appraise files
before they are used. This includes measuring critical system files during
early boot (e.g., init, init scripts, login binaries). If IMA were a
module, it would be loaded too late to cover those.
o TPM Dependency: IMA integrates tightly with the TPM to record
measurements into PCRs. The TPM must be initialized early (ideally before
init_ima()), which aligns with IMA being built-in.
o Security Model: IMA is part of a Trusted Computing Base (TCB). Making it
a module would weaken the security model, as a potentially compromised
system could delay or tamper with its initialization.
IMA must be built-in to ensure it starts measuring from the earliest
possible point in boot which inturn implies TPM must be initialised and
ready to use before IMA.
To enable integration of tpm_event_log with the IMA subsystem, the TPM
drivers (tpm_crb and tpm_crb_ffa) also needs to be built-in. However with
FF-A driver also being initialised at device initcall level, it can lead to
an initialization order issue where:
- crb_acpi_driver_init() may run before tpm_crb_ffa_driver()_init and
ffa_init()
- As a result, probing the TPM device via CRB over FFA is deferred
- ima_init() (called as a late initcall) runs before deferred probe
completes, IMA fails to find the TPM and logs the below error:
| ima: No TPM chip found, activating TPM-bypass!
Eventually it fails to generate boot_aggregate with PCR values.
Because of the above stated dependency, the ffa driver needs to initialised
before tpm_crb_ffa module to ensure IMA finds the TPM successfully when
present.
[ jarkko: reformatted some of the paragraphs because they were going past
the 75 character boundary. ]
Signed-off-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65c430906e ]
GCC appears to have kind of fragile inlining heuristics, in the
sense that it can change whether or not it inlines something based on
optimizations. It looks like the kcov instrumentation being added (or in
this case, removed) from a function changes the optimization results,
and some functions marked "inline" are _not_ inlined. In that case,
we end up with __init code calling a function not marked __init, and we
get the build warnings I'm trying to eliminate in the coming patch that
adds __no_sanitize_coverage to __init functions:
WARNING: modpost: vmlinux: section mismatch in reference: acpi_get_enable_method+0x1c (section: .text.unlikely) -> acpi_psci_present (section: .init.text)
This problem is somewhat fragile (though using either __always_inline
or __init will deterministically solve it), but we've tripped over
this before with GCC and the solution has usually been to just use
__always_inline and move on.
For arm64 this requires forcing one ACPI function to be inlined with
__always_inline.
Link: https://lore.kernel.org/r/20250724055029.3623499-1-kees@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c6363ca1 ]
When the volume header contains erroneous values that do not reflect
the actual state of the filesystem, hfsplus_fill_super() assumes that
the attributes file is not yet created, which later results in hitting
BUG_ON() when hfsplus_create_attributes_file() is called. Replace this
BUG_ON() with -EIO error with a message to suggest running fsck tool.
Reported-by: syzbot <syzbot+1107451c16b9eb9d29e6@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=1107451c16b9eb9d29e6
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Viacheslav Dubeyko <slava@dubeyko.com>
Link: https://lore.kernel.org/r/7b587d24-c8a1-4413-9b9a-00a33fbd849f@I-love.SAKURA.ne.jp
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a431930c9b ]
This patch introduces is_bnode_offset_valid() method that checks
the requested offset value. Also, it introduces
check_and_correct_requested_length() method that checks and
correct the requested length (if it is necessary). These methods
are used in hfs_bnode_read(), hfs_bnode_write(), hfs_bnode_clear(),
hfs_bnode_copy(), and hfs_bnode_move() with the goal to prevent
the access out of allocated memory and triggering the crash.
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
Link: https://lore.kernel.org/r/20250703214912.244138-1-slava@dubeyko.com
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6db015fc4b ]
TLS expects that it owns the receive queue of the TCP socket.
This cannot be guaranteed in case the reader of the TCP socket
entered before the TLS ULP was installed, or uses some non-standard
read API (eg. zerocopy ones). Replace the WARN_ON() and a buggy
early exit (which leaves anchor pointing to a freed skb) with real
error handling. Wipe the parsing state and tell the reader to retry.
We already reload the anchor every time we (re)acquire the socket lock,
so the only condition we need to avoid is an out of bounds read
(not having enough bytes in the socket for previously parsed record len).
If some data was read from under TLS but there's enough in the queue
we'll reload and decrypt what is most likely not a valid TLS record.
Leading to some undefined behavior from TLS perspective (corrupting
a stream? missing an alert? missing an attack?) but no kernel crash
should take place.
Reported-by: William Liu <will@willsroot.io>
Reported-by: Savino Dicanosa <savy@syst3mfailure.io>
Link: https://lore.kernel.org/tFjq_kf7sWIG3A7CrCg_egb8CVsT_gsmHAK0_wxDPJXfIzxFAMxqmLwp3MlU5EHiet0AwwJldaaFdgyHpeIUCS-3m3llsmRzp9xIOBR4lAI=@syst3mfailure.io
Fixes: 84c61fe1a7 ("tls: rx: do not use the standard strparser")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250807232907.600366-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2efe41234d ]
syzbot reported the following ABBA deadlock:
CPU0 CPU1
---- ----
n_vclocks_store()
lock(&ptp->n_vclocks_mux) [1]
(physical clock)
pc_clock_adjtime()
lock(&clk->rwsem) [2]
(physical clock)
...
ptp_clock_freerun()
ptp_vclock_in_use()
lock(&ptp->n_vclocks_mux) [3]
(physical clock)
ptp_clock_unregister()
posix_clock_unregister()
lock(&clk->rwsem) [4]
(virtual clock)
Since ptp virtual clock is registered only under ptp physical clock, both
ptp_clock and posix_clock must be physical clocks for ptp_vclock_in_use()
to lock &ptp->n_vclocks_mux and check ptp->n_vclocks.
However, when unregistering vclocks in n_vclocks_store(), the locking
ptp->n_vclocks_mux is a physical clock lock, but clk->rwsem of
ptp_clock_unregister() called through device_for_each_child_reverse()
is a virtual clock lock.
Therefore, clk->rwsem used in CPU0 and clk->rwsem used in CPU1 are
different locks, but in lockdep, a false positive occurs because the
possibility of deadlock is determined through lock-class.
To solve this, lock subclass annotation must be added to the posix_clock
rwsem of the vclock.
Reported-by: syzbot+7cfb66a237c4a5fb22ad@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=7cfb66a237c4a5fb22ad
Fixes: 73f37068d5 ("ptp: support ptp physical/virtual clocks conversion")
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250728062649.469882-1-aha310510@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa3fa55de0 ]
Marc has reported that commit 85975daeaa ("cpuidle: menu: Avoid
discarding useful information") caused the number of wakeup interrupts
to increase on an idle system [1], which was not expected to happen
after merely allowing shallower idle states to be selected by the
governor in some cases.
However, on the system in question, all of the idle states deeper than
WFI are rejected by the driver due to a firmware issue [2]. This causes
the governor to only consider the recent interval duriation data
corresponding to attempts to enter WFI that are successful and the
recent invervals table is filled with values lower than the scheduler
tick period. Consequently, the governor predicts an idle duration
below the scheduler tick period length and avoids stopping the tick
more often which leads to the observed symptom.
Address it by modifying the governor to update the recent intervals
table also when entering the previously selected idle state fails, so
it knows that the short idle intervals might have been the minority
had the selected idle states been actually entered every time.
Fixes: 85975daeaa ("cpuidle: menu: Avoid discarding useful information")
Link: https://lore.kernel.org/linux-pm/86o6sv6n94.wl-maz@kernel.org/ [1]
Link: https://lore.kernel.org/linux-pm/7ffcb716-9a1b-48c2-aaa4-469d0df7c792@arm.com/ [2]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Christian Loehle <christian.loehle@arm.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/2793874.mvXUDI8C0e@rafael.j.wysocki
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e91a158b69 ]
There is no reason to limit intel_idle's loading of ACPI tables to
family 6. Upcoming Intel processors are not in family 6.
Below "Fixes" really means "applies cleanly until".
That syntax commit didn't change the previous logic,
but shows this patch applies back 5-years.
Fixes: 4a9f45a053 ("intel_idle: Convert to new X86 CPU match macros")
Signed-off-by: Len Brown <len.brown@intel.com>
Link: https://patch.msgid.link/06101aa4fe784e5b0be1cb2c0bdd9afcf16bd9d4.1754681697.git.len.brown@intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f1d1d14db ]
The variable ret in icss_iep_extts_enable() was incorrectly declared
as u32, while the function returns int and may return negative error
codes. This will cause sign extension issues and incorrect error
propagation. Update ret to be int to fix error handling.
This change corrects the declaration to avoid potential type mismatch.
Fixes: c1e0230eea ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250805142323.1949406-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06feac1540 ]
When link settings are changed emac->speed is populated by
emac_adjust_link(). The link speed and other settings are then written into
the DRAM. However if both ports are brought down after this and brought up
again or if the operating mode is changed and a firmware reload is needed,
the DRAM is cleared by icssg_config(). As a result the link settings are
lost.
Fix this by calling emac_adjust_link() after icssg_config(). This re
populates the settings in the DRAM after a new firmware load.
Fixes: 9facce84f4 ("net: ti: icssg-prueth: Fix firmware load sequence.")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Message-ID: <20250805173812.2183161-1-danishanwar@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de788b2e62 ]
There is a reference count leak in ctnetlink_dump_table():
if (res < 0) {
nf_conntrack_get(&ct->ct_general); // HERE
cb->args[1] = (unsigned long)ct;
...
While its very unlikely, its possible that ct == last.
If this happens, then the refcount of ct was already incremented.
This 2nd increment is never undone.
This prevents the conntrack object from being released, which in turn
keeps prevents cnet->count from dropping back to 0.
This will then block the netns dismantle (or conntrack rmmod) as
nf_conntrack_cleanup_net_list() will wait forever.
This can be reproduced by running conntrack_resize.sh selftest in a loop.
It takes ~20 minutes for me on a preemptible kernel on average before
I see a runaway kworker spinning in nf_conntrack_cleanup_net_list.
One fix would to change this to:
if (res < 0) {
if (ct != last)
nf_conntrack_get(&ct->ct_general);
But this reference counting isn't needed in the first place.
We can just store a cookie value instead.
A followup patch will do the same for ctnetlink_exp_dump_table,
it looks to me as if this has the same problem and like
ctnetlink_dump_table, we only need a 'skip hint', not the actual
object so we can apply the same cookie strategy there as well.
Fixes: d205dc4079 ("[NETFILTER]: ctnetlink: fix deadlock in table dumping")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1118aaa3b3 ]
Commit b40c5f4fde ("udp: disable inner UDP checksum offloads in
IPsec case") tried to fix checksumming in UFO when the packets are
going through IPsec, so that we can't rely on offloads because the UDP
header and payload will be encrypted.
But when doing a TCP test over VXLAN going through IPsec transport
mode with GSO enabled (esp4_offload module loaded), I'm seeing broken
UDP checksums on the encap after successful decryption.
The skbs get to udp4_ufo_fragment/__skb_udp_tunnel_segment via
__dev_queue_xmit -> validate_xmit_skb -> skb_gso_segment and at this
point we've already dropped the dst (unless the device sets
IFF_XMIT_DST_RELEASE, which is not common), so need_ipsec is false and
we proceed with checksum offload.
Make need_ipsec also check the secpath, which is not dropped on this
callpath.
Fixes: b40c5f4fde ("udp: disable inner UDP checksum offloads in IPsec case")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45d19b4b6c ]
smaps_hugetlb_range() handles the pte without holdling ptl, and may be
concurrenct with migration, leaing to BUG_ON in pfn_swap_entry_to_page().
The race is as follows.
smaps_hugetlb_range migrate_pages
huge_ptep_get
remove_migration_ptes
folio_unlock
pfn_swap_entry_folio
BUG_ON
To fix it, hold ptl lock in smaps_hugetlb_range().
Link: https://lkml.kernel.org/r/20250724090958.455887-1-tujinjiang@huawei.com
Link: https://lkml.kernel.org/r/20250724090958.455887-2-tujinjiang@huawei.com
Fixes: 25ee01a2fc ("mm: hugetlb: proc: add hugetlb-related fields to /proc/PID/smaps")
Signed-off-by: Jinjiang Tu <tujinjiang@huawei.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Andrei Vagin <avagin@gmail.com>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Brahmajit Das <brahmajit.xyz@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: David Rientjes <rientjes@google.com>
Cc: Dev Jain <dev.jain@arm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Joern Engel <joern@logfs.org>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Thiago Jung Bauermann <thiago.bauermann@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33927f3d0e ]
As soon as we'd inserted a file reference into descriptor table, another
thread could close it. That's fine for the case when all we are doing is
returning that descriptor to userland (it's a race, but it's a userland
race and there's nothing the kernel can do about it). However, if we
follow fd_install() with any kind of access to objects that would be
destroyed on close (be it the struct file itself or anything destroyed
by its ->release()), we have a UAF.
dma_buf_fd() is a combination of reserving a descriptor and fd_install().
habanalabs export_dmabuf() calls it and then proceeds to access the
objects destroyed on close. In particular, it grabs an extra reference to
another struct file that will be dropped as part of ->release() for ours;
that "will be" is actually "might have already been".
Fix that by reserving descriptor before anything else and do fd_install()
only when everything had been set up. As a side benefit, we no longer
have the failure exit with file already created, but reference to
underlying file (as well as ->dmabuf_export_cnt, etc.) not grabbed yet;
unlike dma_buf_fd(), fd_install() can't fail.
Fixes: db1a8dd916 ("habanalabs: add support for dma-buf exporter")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
