Move reboot node under syscon and change compatible string to
fsl,ls1028a-rstcr because it is exactly same as ls1028a.
Fix below warning:
arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dtb:
/syscon@1e60000: failed to match any schema with compatible: ['fsl,ls2080a-rstcr', 'syscon']
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to binding doc http://devicetree.org/schemas/spi/fsl,dspi.yaml
and driver drivers/spi/spi-fsl-dspi.c, default is little-endian, should
use big-endian for big-endian system. Remove 'little-endian' to fix below
warning:
arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-85bb.dtb: spi@2100000: Unevaluated properties are not allowed ('little-endian' was unexpected)
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add native HDMI audio to Verdin iMX8MP and all its carriers boards.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the flexcan[1..5] nodes for imx95.
Reviewed-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DDR Perf Monitor for i.MX95.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
fsl,ls2080a-pcie actual is the same as fsl,ls2085a-pcie. Only keep one is
enough, so remove "fsl,ls2085a-pcie" to fix below warnings.
arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dtb: pcie@3400000: compatible: ['fsl,ls2080a-pcie', 'fsl,ls2085a-pcie'] is too long
from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove undocumented compatible string fsl,ls-pcie-ep to fix below
CHECK_DTBS warning.
arch/arm64/boot/dts/freescale/fsl-ls1046a-frwy.dtb: pcie_ep@3400000: compatible: ['fsl,ls1046a-pcie-ep', 'fsl,ls-pcie-ep'] is too long
from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie-ep.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to binding doc fsl,ddr.yaml, big-endian is default setting. So
remove it to fix below CHECK_DTBS warnings.
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: memory-controller@1080000: 'big-endian' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,ddr.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to binding doc fsl,esdhc.yaml, the default endian mode is
big-endian. So remove big-endian property to fix below CHECK_DTBS warnings:
arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: mmc@1560000: Unevaluated properties are not allowed ('big-endian' was unexpected)
from schema $id: http://devicetree.org/schemas/mmc/fsl,esdhc.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add msi-cell = <1> for GIC ITS. msi-parent have to be kept because it is
checked by U-Boot due to historical reasons to fix up msi-map.
Fix below CHECK_DTBS warning:
arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dtb: interrupt-controller@6000000: msi-controller@6020000: '#msi-cells' is a required property
from schema $id: http://devicetree.org/schemas/interrupt-controller/arm,gic-v3.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add platform specific compatiable string 'fsl,ls1028-reset' for syscon and
move reboot node under reset syscon node to fix below warning.
syscon@1e60000: compatible: 'anyOf' conditional failed, one must be fixed:
['syscon'] is too short
'syscon' is not one of ['al,alpine-sysfabric-service', ...
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change node name 'uqe' to 'uqe-bus'.
Remove #address-cells and #size-cells for nodes, which have not child node.
Fix below CHECK_DTBS warning:
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: uqe@2400000: si@700: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: uqe@2400000: siram@1000: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: uqe@2400000: $nodename:0: 'uqe@2400000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: uqe@2400000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'qeic@80', 'ucc@2000', 'ucc@2200' were unexpected)
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: qeic@80: '#address-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-ic.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: si@700: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-si.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: siram@1000: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-siram.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pcsphy-handle already deprecated according to binding fsl,fman-dtsec.yaml.
Add new common pcs-handle at dts and fix below CHECK_DTBS warning.
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: fman@1a00000: ethernet@e0000: 'pcs-handle' is a dependency of 'pcs-handle-names'
from schema $id: http://devicetree.org/schemas/net/fsl,fman.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Invoke power-domain.yaml if node name as 'power-control'.
Rcpm actually are not power domain controller. It just control wakeup
capability. So rename it as wakeup-control. Fix below CHECK_DTBS warning.
power-controller@1ee2140: '#power-domain-cells' is a required property
from schema $id: http://devicetree.org/schemas/power/power-domain.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The node name 'aux-bus' is special word. It invokes dp-aux-bus.yaml binding
check. Simple change to 'bus' to fix below warning.
aux-bus: '#address-cells', '#size-cells', 'compatible', 'dma-ranges', 'ranges', 'sata@3200000', 'usb@2f00000', 'usb@3000000', 'usb@3100000' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/dp-aux-bus.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SDIO frequency was limited to workaround some instabilities, however it
turned out that the instability had nothing to do with the speed but was
because of an issue with the USDHC IP that was fixed in
commit 52e4c32bae ("mmc: sdhci-esdhc-imx: only enable DAT[0] and CMD line
auto tuning for SDIO device").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX93 features two Cortex-A55 cores with per core L1 Instruction
cache size 32KB, L1 data cache size 32KB, per core L2 cache 64KB, and
unified 256KB L3 cache.
Add the cache info to remove cacheinfo warnings at boot:
"cacheinfo: Unable to detect cache hierarchy for CPU 0"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DMA configurations for LPSPI nodes on i.MX8QX/QM/DXL.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PDM micphone sound card support, configure the pinmux.
This sound card supports recording sound from PDM microphone
and convert the PDM format data to PCM data.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add #sound-dai-cells property for audio cpu dai modules
'#sound-dai-cells' is required to properly interpret
the list of DAI specified in the 'sound-dai' property,
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the pinctrl node in the device tree in order to enable the
S32G2/S32G3 pinctrl driver to probe.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@oss.nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- disable PU/PD if already done with external resistors
- do not configure Schmitt Trigger for outputs
- do not configure DSE / FSEL for inputs
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
100kHz is only needed for the USB Hub TUSB8041. But as this device is not
connected by default, the speed can be increased.
The other busses don't have any 100kHz only devices attached.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These properties are required by i2c-controller.yaml bindings.
Add them on SoC level, rather than on board level.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Neither the imx8dxl-evk or imx8qm-mek have a Rohm DAC on them as far as
I can tell from online documentation, and they certainly do not have a
dh2228fv, as this device does not actually exist! Remove the DAC nodes
from the devicetrees as it is not acceptable to pretend to have a device
on a board in order to bind the spidev driver in Linux.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Micro SD cards can't be physically write-protected like full-sized
cards. Disable this feature in device-tree to get rid of the kernel
warning:
"host does not support reading read-only switch, assuming write-enable"
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a devicetree overlay to disable ethernet for boards where it is not
populated.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
NXP S32G2/S32G3 SoC based platforms do not
use a pin for SD-Card write protection used by
the uSDHC controller.
Hence, adding 'disable-wp' usdhc device-tree property in order to fix
observed warnings on SD boot as the following:
"host does not support reading read-only switch, assuming write-enable"
Signed-off-by: Ciprian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no need to describe the compatible string inside
a dtso file.
dt-schema produces super verbose warnings about that.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Parthiban Nallathambi <parthiban@linumiz.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no need to describe the compatible string inside
a dtso file.
dt-schema produces super verbose warnings about that.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Parthiban Nallathambi <parthiban@linumiz.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add thermal_zone label because it may be overwrite by board level dts file.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add flexspi support.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add sai1, sai2. Add i2c4 and wm8962 and other dependent nodes.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add sai[1..6], NXP Audio Transceiver (XCVR) Controller and MICFIL Digital
Audio Interface (MICFIL).
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add eDMA1, eDMA2 and eDMA3 support for iMX95.
Add dmas and dma-names for each peripheral, which use eDMA.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the board device tree with sdhc1/2, cm33, flexcan, mu, lpuart1,
lpi2c1/2, usb enabled and etc, which to support the i.MX 93 14x14
Evaluation kit that is an automotive market oriented evaluation board
with i.MX 93 application processors in a 14x14mm package.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'#address-cells' and '#size-cells' are already included in soc device tree,
no need add them in board device tree.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For Platform to Agent(p2a) notification, i.MX95 System Manager(SM)
firmware requires a reply communication. So add mailbox channel for
p2a reply communication.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Fix RPM package build error caused by an incorrect locale setup
- Mark modules.weakdep as ghost in RPM package
- Fix the odd combination of -S and -c in stack protector scripts, which
is an error with the latest Clang
-----BEGIN PGP SIGNATURE-----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=HYew
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix RPM package build error caused by an incorrect locale setup
- Mark modules.weakdep as ghost in RPM package
- Fix the odd combination of -S and -c in stack protector scripts,
which is an error with the latest Clang
* tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: Fix '-S -c' in x86 stack protector scripts
kbuild: rpm-pkg: ghost modules.weakdep file
kbuild: rpm-pkg: Fix C locale setup
This simplifies the min_t() and max_t() macros by no longer making them
work in the context of a C constant expression.
That means that you can no longer use them for static initializers or
for array sizes in type definitions, but there were only a couple of
such uses, and all of them were converted (famous last words) to use
MIN_T/MAX_T instead.
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3a7e02c040 ("minmax: avoid overly complicated constant
expressions in VM code") added the simpler MIN_T/MAX_T macros in order
to avoid some excessive expansion from the rather complicated regular
min/max macros.
The complexity of those macros stems from two issues:
(a) trying to use them in situations that require a C constant
expression (in static initializers and for array sizes)
(b) the type sanity checking
and MIN_T/MAX_T avoids both of these issues.
Now, in the whole (long) discussion about all this, it was pointed out
that the whole type sanity checking is entirely unnecessary for
min_t/max_t which get a fixed type that the comparison is done in.
But that still leaves min_t/max_t unnecessarily complicated due to
worries about the C constant expression case.
However, it turns out that there really aren't very many cases that use
min_t/max_t for this, and we can just force-convert those.
This does exactly that.
Which in turn will then allow for much simpler implementations of
min_t()/max_t(). All the usual "macros in all upper case will evaluate
the arguments multiple times" rules apply.
We should do all the same things for the regular min/max() vs MIN/MAX()
cases, but that has the added complexity of various drivers defining
their own local versions of MIN/MAX, so that needs another level of
fixes first.
Link: https://lore.kernel.org/all/b47fad1d0cf8449886ad148f8c013dae@AcuMS.aculab.com/
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Many fixes for power-cut issues by Zhihao Cheng
- Another ubiblock error path fix
- ubiblock section mismatch fix
- Misc fixes all over the place
-----BEGIN PGP SIGNATURE-----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=0y6/
-----END PGP SIGNATURE-----
Merge tag 'ubifs-for-linus-6.11-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
- Many fixes for power-cut issues by Zhihao Cheng
- Another ubiblock error path fix
- ubiblock section mismatch fix
- Misc fixes all over the place
* tag 'ubifs-for-linus-6.11-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: Fix ubi_init() ubiblock_exit() section mismatch
ubifs: add check for crypto_shash_tfm_digest
ubifs: Fix inconsistent inode size when powercut happens during appendant writing
ubi: block: fix null-pointer-dereference in ubiblock_create()
ubifs: fix kernel-doc warnings
ubifs: correct UBIFS_DFS_DIR_LEN macro definition and improve code clarity
mtd: ubi: Restore missing cleanup on ubi_init() failure path
ubifs: dbg_orphan_check: Fix missed key type checking
ubifs: Fix unattached inode when powercut happens in creating
ubifs: Fix space leak when powercut happens in linking tmpfile
ubifs: Move ui->data initialization after initializing security
ubifs: Fix adding orphan entry twice for the same inode
ubifs: Remove insert_dead_orphan from replaying orphan process
Revert "ubifs: ubifs_symlink: Fix memleak of inode->i_link in error path"
ubifs: Don't add xattr inode into orphan area
ubifs: Fix unattached xattr inode if powercut happens after deleting
mtd: ubi: avoid expensive do_div() on 32-bit machines
mtd: ubi: make ubi_class constant
ubi: eba: properly rollback inside self_check_eba
After a recent change in clang to stop consuming all instances of '-S'
and '-c' [1], the stack protector scripts break due to the kernel's use
of -Werror=unused-command-line-argument to catch cases where flags are
not being properly consumed by the compiler driver:
$ echo | clang -o - -x c - -S -c -Werror=unused-command-line-argument
clang: error: argument unused during compilation: '-c' [-Werror,-Wunused-command-line-argument]
This results in CONFIG_STACKPROTECTOR getting disabled because
CONFIG_CC_HAS_SANE_STACKPROTECTOR is no longer set.
'-c' and '-S' both instruct the compiler to stop at different stages of
the pipeline ('-S' after compiling, '-c' after assembling), so having
them present together in the same command makes little sense. In this
case, the test wants to stop before assembling because it is looking at
the textual assembly output of the compiler for either '%fs' or '%gs',
so remove '-c' from the list of arguments to resolve the error.
All versions of GCC continue to work after this change, along with
versions of clang that do or do not contain the change mentioned above.
Cc: stable@vger.kernel.org
Fixes: 4f7fd4d7a7 ("[PATCH] Add the -fstack-protector option to the CFLAGS")
Fixes: 60a5317ff0 ("x86: implement x86_32 stack protector")
Link: 6461e53781 [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
