commit e4940626de upstream.
The problem here is that we check:
if (dev >= SNDRV_CARDS)
Then we increment "dev".
if (!joystick_port[dev++])
Then we use it as an offset into a array with SNDRV_CARDS elements.
if (!request_region(joystick_port[dev], 8, "Riptide gameport")) {
This has 3 effects:
1) If you use the module option to specify the joystick port then it has
to be shifted one space over.
2) The wrong error message will be printed on failure if you have over
32 cards.
3) Static checkers will correctly complain that are off by one.
Fixes: db1005ec6f ('ALSA: riptide - Fix joystick resource handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4ff0f034e9 upstream.
The right check for conf_reg to be invalid it testing against -1 not 0
as is done in the rest of the driver.
This fixes an oops that can be triggered by:
cat /sys/kernel/debug/pinctrl/43fac000.iomuxc/*
Fixes: ae75ff8145 ("pinctrl: pinctrl-imx: add imx pinctrl core driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[ luis: backported to 3.16:
- file rename: drivers/pinctrl/freescale/pinctrl-imx.c ->
drivers/pinctrl/pinctrl-imx.c ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6f20e7f2e9 upstream.
When calling to early_setup(), we pick "boot_paca" up for the master CPU
and initialize that with initialise_paca(). At that point, the SLB
shadow buffer isn't populated yet. Updating the SLB shadow buffer should
corrupt what we had in physical address 0 where the trap instruction is
usually stored.
This hasn't been observed to cause any trouble in practice, but is
obviously fishy.
Fixes: 6f4441ef70 ("powerpc: Dynamically allocate slb_shadow from memblock")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2e9dcdae40 upstream.
In case CLK_GATE_HIWORD_MASK flag is passed to clk_register_gate(), the bit #
should be no higher than 15, however the corresponding check is obviously off-
by-one.
Fixes: 045779942c ("clk: gate: add CLK_GATE_HIWORD_MASK")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 86d68a58d0 upstream.
The "> 0" here should ">= 0" so we free map_entries[0].
Fixes: 926172d460 ('efi: Export EFI runtime memory mapping to sysfs')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7d82bf3419 upstream.
If the call to devm_kzalloc() fails, nothing must be cleant up.
This was missed before because gpio_rcar_probe() had a "return"
statement after the first "goto err0".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: df0c6c8023 ("gpio: rcar: Add minimal runtime PM support")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7331ea474e upstream.
Commit f6b2a04590 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM
setup") converted the driver to register the board level DAPM elements with
the card's DAPM context rather than the CODEC's DAPM context. The change
overlooked that the speaker widget event callback accesses the widget's
codec field which is only valid if the widget has been registered in a CODEC
DAPM context. This patch modifies the callback to take an alternative route
to get the CODEC.
Fixes: f6b2a04590 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM
setup")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0a280962dc upstream.
X-Coverup: just ask spender
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7e0e953bb0 upstream.
use_pde()/unuse_pde() in ->follow_link()/->put_link() resp.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0db59e5929 upstream.
As it is, we have debugfs_remove() racing with symlink traversals.
Supply ->evict_inode() and do freeing there - inode will remain
pinned until we are done with the symlink body.
And rip the idiocy with checking if dentry is positive right after
we'd verified debugfs_positive(), which is a stronger check...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 1467559232 upstream.
The output of KDB 'summary' command should report MemTotal, MemFree
and Buffers output in kB. Current codes report in unit of pages.
A define of K(x) as
is defined in the code, but not used.
This patch would apply the define to convert the values to kB.
Please include me on Cc on replies. I do not subscribe to linux-kernel.
Signed-off-by: Jay Lan <jlan@sgi.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ca5d25642e upstream.
Export the _save_msa asm function used by the lose_fpu(1) macro to GPL
modules so that KVM can make use of it when it is built as a module.
This fixes the following build error when CONFIG_KVM=m and
CONFIG_CPU_HAS_MSA=y due to commit f798217dfd ("KVM: MIPS: Don't leak
FPU/DSP to guest"):
ERROR: "_save_msa" [arch/mips/kvm/kvm.ko] undefined!
Fixes: f798217dfd (KVM: MIPS: Don't leak FPU/DSP to guest)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9261/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3ce465e04b upstream.
Export the _save_fp asm function used by the lose_fpu(1) macro to GPL
modules so that KVM can make use of it when it is built as a module.
This fixes the following build error when CONFIG_KVM=m due to commit
f798217dfd ("KVM: MIPS: Don't leak FPU/DSP to guest"):
ERROR: "_save_fp" [arch/mips/kvm/kvm.ko] undefined!
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: f798217dfd (KVM: MIPS: Don't leak FPU/DSP to guest)
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9260/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7eb71e0351 upstream.
It turns out it's possible to get __remove_osd() called twice on the
same OSD. That doesn't sit well with rb_erase() - depending on the
shape of the tree we can get a NULL dereference, a soft lockup or
a random crash at some point in the future as we end up touching freed
memory. One scenario that I was able to reproduce is as follows:
<osd3 is idle, on the osd lru list>
<con reset - osd3>
con_fault_finish()
osd_reset()
<osdmap - osd3 down>
ceph_osdc_handle_map()
<takes map_sem>
kick_requests()
<takes request_mutex>
reset_changed_osds()
__reset_osd()
__remove_osd()
<releases request_mutex>
<releases map_sem>
<takes map_sem>
<takes request_mutex>
__kick_osd_requests()
__reset_osd()
__remove_osd() <-- !!!
A case can be made that osd refcounting is imperfect and reworking it
would be a proper resolution, but for now Sage and I decided to fix
this by adding a safe guard around __remove_osd().
Fixes: http://tracker.ceph.com/issues/8087
Cc: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit cc9f1f518c upstream.
No reason to use BUG_ON for osd request list assertions.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7c6e6fc53e upstream.
It is important that both regular and lingering requests lists are
empty when the OSD is removed.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4e7c22d447 upstream.
The issue is that the stack for processes is not properly randomized on
64 bit architectures due to an integer overflow.
The affected function is randomize_stack_top() in file
"fs/binfmt_elf.c":
static unsigned long randomize_stack_top(unsigned long stack_top)
{
unsigned int random_variable = 0;
if ((current->flags & PF_RANDOMIZE) &&
!(current->personality & ADDR_NO_RANDOMIZE)) {
random_variable = get_random_int() & STACK_RND_MASK;
random_variable <<= PAGE_SHIFT;
}
return PAGE_ALIGN(stack_top) + random_variable;
return PAGE_ALIGN(stack_top) - random_variable;
}
Note that, it declares the "random_variable" variable as "unsigned int".
Since the result of the shifting operation between STACK_RND_MASK (which
is 0x3fffff on x86_64, 22 bits) and PAGE_SHIFT (which is 12 on x86_64):
random_variable <<= PAGE_SHIFT;
then the two leftmost bits are dropped when storing the result in the
"random_variable". This variable shall be at least 34 bits long to hold
the (22+12) result.
These two dropped bits have an impact on the entropy of process stack.
Concretely, the total stack entropy is reduced by four: from 2^28 to
2^30 (One fourth of expected entropy).
This patch restores back the entropy by correcting the types involved
in the operations in the functions randomize_stack_top() and
stack_maxrandom_size().
The successful fix can be tested with:
$ for i in `seq 1 10`; do cat /proc/self/maps | grep stack; done
7ffeda566000-7ffeda587000 rw-p 00000000 00:00 0 [stack]
7fff5a332000-7fff5a353000 rw-p 00000000 00:00 0 [stack]
7ffcdb7a1000-7ffcdb7c2000 rw-p 00000000 00:00 0 [stack]
7ffd5e2c4000-7ffd5e2e5000 rw-p 00000000 00:00 0 [stack]
...
Once corrected, the leading bytes should be between 7ffc and 7fff,
rather than always being 7fff.
Signed-off-by: Hector Marco-Gisbert <hecmargi@upv.es>
Signed-off-by: Ismael Ripoll <iripoll@upv.es>
[ Rebased, fixed 80 char bugs, cleaned up commit message, added test example and CVE ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: CVE-2015-1593
Link: http://lkml.kernel.org/r/20150214173350.GA18393@www.outflux.net
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 61882b6317 upstream.
The two functions s3c2416_cpufreq_driver_init and s3c_cpufreq_register
are marked init but are called from a context that might be run after
the __init sections are discarded, as the compiler points out:
WARNING: vmlinux.o(.data+0x1ad9dc): Section mismatch in reference from the variable s3c2416_cpufreq_driver to the function .init.text:s3c2416_cpufreq_driver_init()
WARNING: drivers/built-in.o(.text+0x35b5dc): Section mismatch in reference from the function s3c2410a_cpufreq_add() to the function .init.text:s3c_cpufreq_register()
This removes the __init markings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 22aa66a3ee upstream.
When the snapshot target is unloaded, snapshot_dtr() waits until
pending_exceptions_count drops to zero. Then, it destroys the snapshot.
Therefore, the function that decrements pending_exceptions_count
should not touch the snapshot structure after the decrement.
pending_complete() calls free_pending_exception(), which decrements
pending_exceptions_count, and then it performs up_write(&s->lock) and it
calls retry_origin_bios() which dereferences s->origin. These two
memory accesses to the fields of the snapshot may touch the dm_snapshot
struture after it is freed.
This patch moves the call to free_pending_exception() to the end of
pending_complete(), so that the snapshot will not be destroyed while
pending_complete() is in progress.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2bec1f4a88 upstream.
The function dm_get_md finds a device mapper device with a given dev_t,
increases the reference count and returns the pointer.
dm_get_md calls dm_find_md, dm_find_md takes _minor_lock, finds the
device, tests that the device doesn't have DMF_DELETING or DMF_FREEING
flag, drops _minor_lock and returns pointer to the device. dm_get_md then
calls dm_get. dm_get calls BUG if the device has the DMF_FREEING flag,
otherwise it increments the reference count.
There is a possible race condition - after dm_find_md exits and before
dm_get is called, there are no locks held, so the device may disappear or
DMF_FREEING flag may be set, which results in BUG.
To fix this bug, we need to call dm_get while we hold _minor_lock. This
patch renames dm_find_md to dm_get_md and changes it so that it calls
dm_get while holding the lock.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 29183a70b0 upstream.
Additional validation of adjtimex freq values to avoid
potential multiplication overflows were added in commit
5e5aeb4367 (time: adjtimex: Validate the ADJ_FREQUENCY values)
Unfortunately the patch used LONG_MAX/MIN instead of
LLONG_MAX/MIN, which was fine on 64-bit systems, but being
much smaller on 32-bit systems caused false positives
resulting in most direct frequency adjustments to fail w/
EINVAL.
ntpd only does direct frequency adjustments at startup, so
the issue was not as easily observed there, but other time
sync applications like ptpd and chrony were more effected by
the bug.
See bugs:
https://bugzilla.kernel.org/show_bug.cgi?id=92481https://bugzilla.redhat.com/show_bug.cgi?id=1188074
This patch changes the checks to use LLONG_MAX for
clarity, and additionally the checks are disabled
on 32-bit systems since LLONG_MAX/PPM_SCALE is always
larger then the 32-bit long freq value, so multiplication
overflows aren't possible there.
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: George Joseph <george.joseph@fairview5.com>
Tested-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Link: http://lkml.kernel.org/r/1423553436-29747-1-git-send-email-john.stultz@linaro.org
[ Prettified the changelog and the comments a bit. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5e5aeb4367 upstream.
Verify that the frequency value from userspace is valid and makes sense.
Unverified values can cause overflows later on.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[jstultz: Fix up bug for negative values and drop redunent cap check]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 8d1e5a1a1c upstream.
With task_blocks_on_rt_mutex() returning early -EDEADLK we never
add the waiter to the waitqueue. Later, we try to remove it via
remove_waiter() and go boom in rt_mutex_top_waiter() because
rb_entry() gives a NULL pointer.
( Tested on v3.18-RT where rtmutex is used for regular mutex and I
tried to get one twice in a row. )
Not sure when this started but I guess 397335f004 ("rtmutex: Fix
deadlock detector for real") or commit 3d5c9340d1 ("rtmutex:
Handle deadlock detection smarter").
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1424187823-19600-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 26ac107378 upstream.
Commit a7854487cd:
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
Causes an RCW cycle to be forced even when the array is degraded.
A degraded array cannot support RCW as that requires reading all data
blocks, and one may be missing.
Forcing an RCW when it is not possible causes a live-lock and the code
spins, repeatedly deciding to do something that cannot succeed.
So change the condition to only force RCW on non-degraded arrays.
Reported-by: Manibalan P <pmanibalan@amiindia.co.in>
Bisected-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: a7854487cd
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit acac4108df upstream.
The "addi" instruction will trap on overflows which is not something
we need in this code, so we replace that with "addiu".
Link: http://www.linux-mips.org/archives/linux-mips/2015-01/msg00430.html
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 98a833c1fa upstream.
The "add" instruction is actually a macro in binutils and depending on
the size of the immediate it can expand to an "addi" instruction.
However, the "addi" instruction traps on overflows which is not
something we want on address calculation.
Link: http://www.linux-mips.org/archives/linux-mips/2015-01/msg00121.html
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 18c0b82a3e upstream.
This changeset removes all the code that allows the driver to write to
the EEPROM and update the recorded error counters and power on hours.
These two stats are unused and writing them exposes a timing risk
which could leave the EEPROM in a bad state preventing further normal
operation of the HCA.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3b524a683a upstream.
Fix SCSI generic read() incorrectly returning success after detecting an
error.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f76a610a8b upstream.
In reference to bug https://bugzilla.redhat.com/show_bug.cgi?id=1097141
Assert is seen with AMD cpu whenever calling pci_alloc_consistent.
[ 29.406183] ------------[ cut here ]------------
[ 29.410505] kernel BUG at lib/iommu-helper.c:13!
Signed-off-by: Minh Tran <minh.tran@emulex.com>
Fixes: 6733b39a13
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit eb71f8a5e3 upstream.
The tpm_ibmvtpm module is affected by an unaligned access problem.
ibmvtpm_crq_get_version failed with rc=-4 during boot when vTPM is
enabled in Power partition, which supports both little endian and
big endian modes.
We added little endian support to fix this problem:
1) added cpu_to_be64 calls to ensure BE data is sent from an LE OS.
2) added be16_to_cpu and be32_to_cpu calls to make sure data received
is in LE format on a LE OS.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
[phuewe: manually applied the patch :( ]
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 1a4bcf470c upstream.
We have a scenario where after the fsync log replay we can lose file data
that had been previously fsync'ed if we added an hard link for our inode
and after that we sync'ed the fsync log (for example by fsync'ing some
other file or directory).
This is because when adding an hard link we updated the inode item in the
log tree with an i_size value of 0. At that point the new inode item was
in memory only and a subsequent fsync log replay would not make us lose
the file data. However if after adding the hard link we sync the log tree
to disk, by fsync'ing some other file or directory for example, we ended
up losing the file data after log replay, because the inode item in the
persisted log tree had an an i_size of zero.
This is easy to reproduce, and the following excerpt from my test for
xfstests shows this:
_scratch_mkfs >> $seqres.full 2>&1
_init_flakey
_mount_flakey
# Create one file with data and fsync it.
# This made the btrfs fsync log persist the data and the inode metadata with
# a correct inode->i_size (4096 bytes).
$XFS_IO_PROG -f -c "pwrite -S 0xaa -b 4K 0 4K" -c "fsync" \
$SCRATCH_MNT/foo | _filter_xfs_io
# Now add one hard link to our file. This made the btrfs code update the fsync
# log, in memory only, with an inode metadata having a size of 0.
ln $SCRATCH_MNT/foo $SCRATCH_MNT/foo_link
# Now force persistence of the fsync log to disk, for example, by fsyncing some
# other file.
touch $SCRATCH_MNT/bar
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/bar
# Before a power loss or crash, we could read the 4Kb of data from our file as
# expected.
echo "File content before:"
od -t x1 $SCRATCH_MNT/foo
# Simulate a crash/power loss.
_load_flakey_table $FLAKEY_DROP_WRITES
_unmount_flakey
_load_flakey_table $FLAKEY_ALLOW_WRITES
_mount_flakey
# After the fsync log replay, because the fsync log had a value of 0 for our
# inode's i_size, we couldn't read anymore the 4Kb of data that we previously
# wrote and fsync'ed. The size of the file became 0 after the fsync log replay.
echo "File content after:"
od -t x1 $SCRATCH_MNT/foo
Another alternative test, that doesn't need to fsync an inode in the same
transaction it was created, is:
_scratch_mkfs >> $seqres.full 2>&1
_init_flakey
_mount_flakey
# Create our test file with some data.
$XFS_IO_PROG -f -c "pwrite -S 0xaa -b 8K 0 8K" \
$SCRATCH_MNT/foo | _filter_xfs_io
# Make sure the file is durably persisted.
sync
# Append some data to our file, to increase its size.
$XFS_IO_PROG -f -c "pwrite -S 0xcc -b 4K 8K 4K" \
$SCRATCH_MNT/foo | _filter_xfs_io
# Fsync the file, so from this point on if a crash/power failure happens, our
# new data is guaranteed to be there next time the fs is mounted.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo
# Add one hard link to our file. This made btrfs write into the in memory fsync
# log a special inode with generation 0 and an i_size of 0 too. Note that this
# didn't update the inode in the fsync log on disk.
ln $SCRATCH_MNT/foo $SCRATCH_MNT/foo_link
# Now make sure the in memory fsync log is durably persisted.
# Creating and fsync'ing another file will do it.
touch $SCRATCH_MNT/bar
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/bar
# As expected, before the crash/power failure, we should be able to read the
# 12Kb of file data.
echo "File content before:"
od -t x1 $SCRATCH_MNT/foo
# Simulate a crash/power loss.
_load_flakey_table $FLAKEY_DROP_WRITES
_unmount_flakey
_load_flakey_table $FLAKEY_ALLOW_WRITES
_mount_flakey
# After mounting the fs again, the fsync log was replayed.
# The btrfs fsync log replay code didn't update the i_size of the persisted
# inode because the inode item in the log had a special generation with a
# value of 0 (and it couldn't know the correct i_size, since that inode item
# had a 0 i_size too). This made the last 4Kb of file data inaccessible and
# effectively lost.
echo "File content after:"
od -t x1 $SCRATCH_MNT/foo
This isn't a new issue/regression. This problem has been around since the
log tree code was added in 2008:
Btrfs: Add a write ahead tree log to optimize synchronous operations
(commit e02119d5a7)
Test cases for xfstests follow soon.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit aa179935ed upstream.
This patch adds a check to sbc_parse_cdb() in order to detect when
an LBA + sector vs. end-of-device calculation wraps when the LBA is
sufficently large enough (eg: 0xFFFFFFFFFFFFFFFF).
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 8e575c50a1 upstream.
This patch adds a check to sbc_setup_write_same() to verify
the incoming WRITE_SAME LBA + number of blocks does not exceed
past the end-of-device.
Also check for potential LBA wrap-around as well.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f4086a3d78 upstream.
Commit 411a99adff (nfs: clear_request_commit while holding i_lock)
assumes that the nfs_commit_info always points to the inode->i_lock.
For historical reasons, that is not the case for O_DIRECT writes.
Cc: Weston Andros Adamson <dros@primarydata.com>
Fixes: 411a99adff ("nfs: clear_request_commit while holding i_lock")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 37527b8692 upstream.
I created a dm-raid1 device backed by a device that supports DISCARD
and another device that does NOT support DISCARD with the following
dm configuration:
# echo '0 2048 mirror core 1 512 2 /dev/sda 0 /dev/sdb 0' | dmsetup create moo
# lsblk -D
NAME DISC-ALN DISC-GRAN DISC-MAX DISC-ZERO
sda 0 4K 1G 0
`-moo (dm-0) 0 4K 1G 0
sdb 0 0B 0B 0
`-moo (dm-0) 0 4K 1G 0
Notice that the mirror device /dev/mapper/moo advertises DISCARD
support even though one of the mirror halves doesn't.
If I issue a DISCARD request (via fstrim, mount -o discard, or ioctl
BLKDISCARD) through the mirror, kmirrord gets stuck in an infinite
loop in do_region() when it tries to issue a DISCARD request to sdb.
The problem is that when we call do_region() against sdb, num_sectors
is set to zero because q->limits.max_discard_sectors is zero.
Therefore, "remaining" never decreases and the loop never terminates.
To fix this: before entering the loop, check for the combination of
REQ_DISCARD and no discard and return -EOPNOTSUPP to avoid hanging up
the mirror device.
This bug was found by the unfortunate coincidence of pvmove and a
discard operation in the RHEL 6.5 kernel; upstream is also affected.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f2ed51ac64 upstream.
It may be possible that a device claims discard support but it rejects
discards with -EOPNOTSUPP. It happens when using loopback on ext2/ext3
filesystem driven by the ext4 driver. It may also happen if the
underlying devices are moved from one disk on another.
If discard error happens, we reject the bio with -EOPNOTSUPP, but we do
not degrade the array.
This patch fixes failed test shell/lvconvert-repair-transient.sh in the
lvm2 testsuite if the testsuite is extracted on an ext2 or ext3
filesystem and it is being driven by the ext4 driver.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f0153c3d94 upstream.
RME RayDAT and AIO use a fixed buffer size of 16384 samples. With period
sizes of 32-4096, this translates to 4-512 periods.
The older RME cards have a variable buffer size but require exactly two
periods.
This patch enforces nperiods=2 on those cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 09b6e85fc8 upstream.
Missing parameter when fetching the real voltage values
from atom. Fixes problems with dynamic clocking on
certain boards.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=87457
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 66c2b84ba6 upstream.
Don't restrict it to just eDP panels. Some LVDS bridge chips require
this. Fixes blank panels on resume on certain laptops. Noticed
by mrnuke on IRC.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=42960
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 06f34e1c28 upstream.
We used to calculate page address differently in 2 cases:
1. In virt_to_page(x) we do
--->8---
mem_map + (x - CONFIG_LINUX_LINK_BASE) >> PAGE_SHIFT
--->8---
2. In in pte_page(x) we do
--->8---
mem_map + (pte_val(x) - PAGE_OFFSET) >> PAGE_SHIFT
--->8---
That leads to problems in case PAGE_OFFSET != CONFIG_LINUX_LINK_BASE -
different pages will be selected depending on where and how we calculate
page address.
In particular in the STAR 9000853582 when gdb attempted to read memory
of another process it got improper page in get_user_pages() because this
is exactly one of the places where we search for a page by pte_page().
The fix is trivial - we need to calculate page address similarly in both
cases.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7976eb49cb upstream.
Otherwise, the mute led can't work at all.
Tested-by: Taihsiang Ho <taihsiang.ho@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1410704
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9ab3b598d2 upstream.
A race condition starts to be visible in recent mmotm, where a PG_hwpoison
flag is set on a migration source page *before* it's back in buddy page
poo= l.
This is problematic because no page flag is supposed to be set when
freeing (see __free_one_page().) So the user-visible effect of this race
is that it could trigger the BUG_ON() when soft-offlining is called.
The root cause is that we call lru_add_drain_all() to make sure that the
page is in buddy, but that doesn't work because this function just
schedule= s a work item and doesn't wait its completion.
drain_all_pages() does drainin= g directly, so simply dropping
lru_add_drain_all() solves this problem.
Fixes: f15bdfa802 ("mm/memory-failure.c: fix memory leak in successful soft offlining")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9cb12d7b4c upstream.
For whatever reason, generic_access_phys() only remaps one page, but
actually allows to access arbitrary size. It's quite easy to trigger
large reads, like printing out large structure with gdb, which leads to a
crash. Fix it by remapping correct size.
Fixes: 28b2ee20c7 ("access_process_vm device memory infrastructure")
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 372549c2a3 upstream.
What we want to check here is whether there is highorder freepage in buddy
list of other migratetype in order to steal it without fragmentation.
But, current code just checks cc->order which means allocation request
order. So, this is wrong.
Without this fix, non-movable synchronous compaction below pageblock order
would not stopped until compaction is complete, because migratetype of
most pageblocks are movable and high order freepage made by compaction is
usually on movable type buddy list.
There is some report related to this bug. See below link.
http://www.spinics.net/lists/linux-mm/msg81666.html
Although the issued system still has load spike comes from compaction,
this makes that system completely stable and responsive according to his
report.
stress-highalloc test in mmtests with non movable order 7 allocation
doesn't show any notable difference in allocation success rate, but, it
shows more compaction success rate.
Compaction success rate (Compaction success * 100 / Compaction stalls, %)
18.47 : 28.94
Fixes: 1fb3f8ca0e ("mm: compaction: capture a suitable high-order page immediately when it is made available")
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f161d4b44d upstream.
This patch addresses the original PR_APTPL_BUF_LEN = 8k limitiation
for write-out of PR APTPL metadata that Martin has recently been
running into.
It changes core_scsi3_update_and_write_aptpl() to use vzalloc'ed
memory instead of kzalloc, and increases the default hardcoded
length to 256k.
It also adds logic in core_scsi3_update_and_write_aptpl() to double
the original length upon core_scsi3_update_aptpl_buf() failure, and
retries until the vzalloc'ed buffer is large enough to accommodate
the outgoing APTPL metadata.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
