This is the typical message you get if you plug in a CPU
which is newer than your BIOS. It's annoying seeing this
message for each core.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Limit sampling rate to transition_latency * 100 or kernel limits.
If sampling_rate is tried to be set too low, set the lowest allowed value.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
The same info can be obtained via the transition_latency sysfs file
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
powernow-k8 driver should always try to get cpufreq info from ACPI.
Otherwise it will not be able to detect the transition latency correctly
which results in ondemand governor taking a wrong sampling rate which will
then result in sever performance loss.
Let the user not shoot himself in the foot and always compile in ACPI
support for powernow-k8.
This also fixes a wrong message if ACPI_PROCESSOR is compiled as a module and
#ifndef CONFIG_ACPI_PROCESSOR
path is chosen.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
It's not only useful for the ondemand and conservative governors, but
also for userspace daemons to know about the HW transition latency of
the CPU.
It is especially useful for userspace to know about this value when
the ondemand or conservative governors are run. The sampling rate
control value depends on it and for userspace being able to set sane
tuning values there it has to know about the transition latency.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
This driver has so many long function names, and deep nested if's
The remaining warnings will need some code restructuring to clean up.
Signed-off-by: Dave Jones <davej@redhat.com>
The remaining warning about the simple_strtoul conversion
to strict_strtoul seems kind of pointless to me.
Signed-off-by: Dave Jones <davej@redhat.com>
GNU indent complains about this being ambiguous, because it's dumb.
One of my automated tests relies on the output of indent, so this shuts
it up.
Signed-off-by: Dave Jones <davej@redhat.com>
This patch adds the directory /debug/tracing/events/ that will contain
all the registered trace points.
# ls /debug/tracing/events/
sched_kthread_stop sched_process_fork sched_switch
sched_kthread_stop_ret sched_process_free sched_wait_task
sched_migrate_task sched_process_wait sched_wakeup
sched_process_exit sched_signal_send sched_wakeup_new
# ls /debug/tracing/events/sched_switch/
enable
# cat /debug/tracing/events/sched_switch/enable
1
# cat /debug/tracing/set_event
sched_switch
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
This patch changes the trace/sched.h to use the DECLARE_TRACE_FMT
such that they are automatically registered with the event tracer.
And it also adds the tracing sched headers to kernel/trace/events.c
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
This patch creates the event tracing infrastructure of ftrace.
It will create the files:
/debug/tracing/available_events
/debug/tracing/set_event
The available_events will list the trace points that have been
registered with the event tracer.
set_events will allow the user to enable or disable an event hook.
example:
# echo sched_wakeup > /debug/tracing/set_event
Will enable the sched_wakeup event (if it is registered).
# echo "!sched_wakeup" >> /debug/tracing/set_event
Will disable the sched_wakeup event (and only that event).
# echo > /debug/tracing/set_event
Will disable all events (notice the '>')
# cat /debug/tracing/available_events > /debug/tracing/set_event
Will enable all registered event hooks.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
This patch creates a DEFINE_TRACE_FMT to map to DECLARE_TRACE.
This allows for the developers to place format strings and
args in with their tracepoint declaration. A tracer may now
override the DEFINE_TRACE_FMT macro and use it to record
a default format.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
There has been a race in raid10 and raid1 for a long time
which has only recently started showing up due to a scheduler changed.
When a sync_read request finishes, as soon as reschedule_retry
is called, another thread can mark the resync request as having
completed, so md_do_sync can finish, ->stop can be called, and
->conf can be freed. So using conf after reschedule_retry is not
safe.
Similarly, when finishing a sync_write, calling md_done_sync must be
the last thing we do, as it allows a chain of events which will free
conf and other data structures.
The first of these requires action in raid10.c
The second requires action in raid1.c and raid10.c
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
For raid1/4/5/6, resync (fixing inconsistencies between devices) is
very similar to recovery (rebuilding a failed device onto a spare).
The both walk through the device addresses in order.
For raid10 it can be quite different. resync follows the 'array'
address, and makes sure all copies are the same. Recover walks
through 'device' addresses and recreates each missing block.
The 'bitmap_cond_end_sync' function allows the write-intent-bitmap
(When present) to be updated to reflect a partially completed resync.
It makes assumptions which mean that it does not work correctly for
raid10 recovery at all.
In particularly, it can cause bitmap-directed recovery of a raid10 to
not recovery some of the blocks that need to be recovered.
So move the call to bitmap_cond_end_sync into the resync path, rather
than being in the common "resync or recovery" path.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When doing recovery on a raid10 with a write-intent bitmap, we only
need to recovery chunks that are flagged in the bitmap.
However if we choose to skip a chunk as it isn't flag, the code
currently skips the whole raid10-chunk, thus it might not recovery
some blocks that need recovering.
This patch fixes it.
In case that is confusing, it might help to understand that there
is a 'raid10 chunk size' which guides how data is distributed across
the devices, and a 'bitmap chunk size' which says how much data
corresponds to a single bit in the bitmap.
This bug only affects cases where the bitmap chunk size is smaller
than the raid10 chunk size.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Impact: cleanup
Unused macro parameters cause spurious unused variable warnings.
Convert all cacheflush macros to inline functions to avoid the
warnings and achieve better type checking.
Signed-off-by: Tejun Heo <tj@kernel.org>
Recent changes in setup_percpu.c made a now meaningless DBG()
statement fail to compile and introduced a
comparison-of-different-types warning. Fix them.
Compile failure is reported by Ingo Molnar.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Ingo Molnar <mingo@elte.hu>
Split pci probe function into smaller logical blocks.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it was pointed out on the list that ixgbe was failing when using 64kB pages
and large 16kB MTU.
since with a 64kB PAGE_SIZE MAX_SKB_FRAGS = 3, the way the driver was
configuring page usage was assuming 2kB is half a page, and was only
ever dmaing that much data to a half page.
(16kB - header size) / 2048 = 7 or 8 pages, which would far exceed 3
adjust the driver to account for these large pages, the hardware can
support DMA to up to 16kB for each descriptor.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Shannon Nelson <shannon.nelson@intel.com>
The ring_feature member of ixgbe_adapter is statically allocated based on
the supported features of the device. When a new feature is added, we need
to manually update the static allocation. This patch makes the feature
list an enum, eliminating the need for multiple updates to the code when
adding a new feature.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: defconfig change
Enable MCE in the 64-bit defconfig.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This will reduce the number of writes done on resume, allowing that to
complete faster (especially on systems with very slow I2C like the
current Samsung driver).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The base support for the only in-tree user, the GTA01, is out of tree
and will be updated separately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch should be pure code motion, separating that out from the
functional changes to move to new style device registration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>