Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.
Size details after cross compiling the .o file for blackfin architecture.
File size before:
text data bss dec hex filename
3572 320 16 3908 f44 tty/serial/bfin_sport_uart.o
File size after:
text data bss dec hex filename
3664 228 16 3908 f44 tty/serial/bfin_sport_uart.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to set PCI bus mastering when device is not doing any DMA. It
includes MSI type of interrupts. Currently only UART on Denverton, which is DMA
capable, might have MSI enabled.
Taking above into account enable bus mastering for Denverton case only.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable MSI type of interrupt if PCI BIOS supports it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from Tangier B0 and continuing on Anniedale the HSU DMA interrupt
line is actually shared with UART. Handling them independently is racy and
quite often comes with the following traceback.
irq 54: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.0-rc6-edison64-86244934+ #1
Hardware name: Intel Corporation Merrifield/BODEGA BAY, BIOS 542 2015.01.21:18.19.48
ffff88003f203eb0 ffffffff8130e718 ffff880032627000 ffff88003262709c
ffff88003f203ed8 ffffffff810a3960 ffff880032627000 0000000000000000
ffff880032627000 ffff88003f203f10 ffffffff810a3cc7 ffff880032627000
Call Trace:
<IRQ>
[<ffffffff8130e718>] dump_stack+0x4d/0x65
[<ffffffff810a3960>] __report_bad_irq+0x30/0xc0
[<ffffffff810a3cc7>] note_interrupt+0x227/0x270
[<ffffffff810a1380>] handle_irq_event_percpu+0x40/0x50
[<ffffffff810a13b7>] handle_irq_event+0x27/0x50
[<ffffffff810a42d5>] handle_fasteoi_irq+0x85/0x150
[<ffffffff8101d7fe>] handle_irq+0x6e/0x120
[<ffffffff8105b8bc>] ? _local_bh_enable+0x1c/0x50
[<ffffffff8101d0d6>] do_IRQ+0x46/0xd0
[<ffffffff818cef3f>] common_interrupt+0x7f/0x7f
<EOI>
[<ffffffff818cdead>] ? mwait_idle+0x7d/0x140
[<ffffffff81024c9a>] arch_cpu_idle+0xa/0x10
[<ffffffff818ce150>] default_idle_call+0x20/0x30
[<ffffffff810908fd>] cpu_startup_entry+0x16d/0x1d0
[<ffffffff818c882d>] rest_init+0x6d/0x70
[<ffffffff81f93e8f>] start_kernel+0x3e2/0x3ef
[<ffffffff81f9343d>] x86_64_start_reservations+0x38/0x3a
[<ffffffff81f93529>] x86_64_start_kernel+0xea/0xed
handlers:
[<ffffffff81411670>] serial8250_interrupt
Disabling IRQ #54
Fix this by handling interrupt only in one place.
The issue is discussed here: https://github.com/andy-shev/linux/issues/5
Moreover this also fixes another bug when Rx DMA returns wrong residue and we
can't rely on it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the most common use case, the Synopsys DW UART driver does not
set the set_termios callback function. This prevents UPSTAT_AUTOCTS
from being set when the UART flag CRTSCTS is set. As a result, the
driver will use software flow control as opposed to hardware flow
control.
To fix the problem, the set_termios callback function is set to the
DW specific function. The logic to set UPSTAT_AUTOCTS is moved so
that any clock error will not affect setting the hardware flow
control.
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Jason Uy <jason.uy@broadcom.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 345857b ("HID: wacom: generic: Add support for sensor offsets") included
a change to the operation and location of the call to 'wacom_add_shared_data'
in 'wacom_parse_and_register'. The modifications included moving it higher up
so that it would occur before the call to 'wacom_retrieve_hid_descriptor'. This
was done to prevent a crash that would have occured when the report containing
tablet offsets was fed into the driver with 'wacom_hid_report_raw_event'
(specifically: the various 'wacom_wac_*_report' functions were written with the
assumption that they would only be called once tablet setup had completed;
'wacom_wac_pen_report' in particular dereferences 'shared' which wasn't yet
allocated).
Moving the call to 'wacom_add_shared_data' effectively prevented the crash but
also broke the sibiling detection code which assumes that the HID descriptor
has been read and the various device_type flags set.
To fix this situation, we restore the original 'wacom_add_shared_data'
operation and location and instead implement an alternative change that can
also prevent the crash. Specifically, we notice that the report functions
mentioned above expect to be called only for input reports. By adding a check,
we can prevent feature reports (such as the offset report) from
causing trouble.
Fixes: 345857bb49 ("HID: wacom: generic: Add support for sensor offsets")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Not clearing the previous tx bit rate status
results in a ambigous tx bit rate reporting to
mac80211/cfg80211, for example the previous bit
rate status would have been marked as legacy rate
, while the current rate would have been an HT/VHT
rate with the tx bit rate flags set and this results
in exporting tx bitrate as legacy rate but with HT/VHT
rate flags set, fix this by clearing the tx bitrate
status for each event. This also fixes the below
warning when we do:
iw dev wlan#N station dump
WARNING: net/wireless/util.c:1222 cfg80211
[<c022f104>] (warn_slowpath_null) from [<bf3b9adc>]
(cfg80211_calculate_bitrate+0x110/0x1f4 [cfg80211])
[<bf3b9adc>] (cfg80211_calculate_bitrate [cfg80211]) from
[<bf3dcd54>] (nl80211_put_sta_rate+0x44/0x1dc [cfg80211])
[<bf3dcd54>] (nl80211_put_sta_rate [cfg80211]) from
[<bf3cbc34>] (nl80211_set_interface+0x724/0xd70 [cfg80211])
[<bf3cbc34>] (nl80211_set_interface [cfg80211]) from
[<bf3d0a18>] (nl80211_dump_station+0xdc/0x100 [cfg80211])
[<bf3d0a18>] (nl80211_dump_station [cfg80211])
Fixes: cec17c3821 ("ath10k: add per peer htt tx stats support for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Station pointers are RCU protected so driver must
be extra careful if it tries to store them
internally for later use outside of the RCU
section it obtained it in.
It was possible for station teardown to race with
some htt events. The possible outcome could be a
use-after-free and a crash.
Only peer-flow-control capable firmware was
affected (so hardware-wise qca99x0 and qca4019).
This could be done in sta_state() itself via
explicit synchronize_net() call but there's
already a convenient sta_pre_rcu_remove() op that
can be hooked up to avoid extra rcu stall.
The peer->sta pointer itself can't be set to
NULL/ERR_PTR because it is later used in
sta_state() for extra sanity checks.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
SCI instances found in SH SoCs have different spacing between registers
depending on the SoC. The platform data contains a regshift field that
tells the driver by how many bits to shift the register offset to
compute its address. We can compute the regshift value automatically
based on the memory resource size, there's no need to pass the value
through platform data.
Fix the sh7750 SCI and sh7760 SIM port memory resources length to ensure
proper computation of the regshift value.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The field isn't set by any platform but is only used internally in the
driver to hold data parsed from DT. Move it to the sci_port structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sh-sci driver implements manual break debouncing for a few SH
platforms by reading the value of the RX pin port register. This feature
is optional and the driver considers all negative or zero values of the
platform data port_reg field as invalid. As the four platforms that set
the field to a register address all use an address higher than
0x7fffffff, the driver will always consider the value as invalid and
never perform debouncing. The feature is unused, remove it.
Debouncing could be implemented properly in the future using the pinctrl
and GPIO APIs if desired.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only SH platforms still use platform data for the sh-sci, and none of
them declare DMA channels connected to the SCI. Remove the corresponding
platform data fields and simplify the driver accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fifo size, overrun register and mask, sampling rate mask and error
mask all depend on the port type only and don't need to be computed at
runtime. Add them to the sci_port_parameters structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver modifies platform data for internal purpose only. Fix that
and make the platform data structure const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turn the regmap two-dimensional array to an array of port parameters and
store a pointer to the port parameters in the sci_port structure. This
will allow handling additional port type dependent parameters.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though most of its registers are 8-bit wide, the IRDA has two
16-bit registers that make it a 16-bit peripheral and not a 8-bit
peripheral with addresses shifted by one. Fix the registers offset in
the driver and the platform data regshift value.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the datasheets, the sh7760 SIM and sh7723 SCIFA instances
don't implement the REIE bit. Don't set it in platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bit is only set by platforms that also set the CKE1 but, in which
case its value is ignored by the device. Don't set it, this simplifies
platform data and only leaves the CKE1 bit to be handled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver considers all negative or zero values of the port_reg field
as invalid. The four platforms that set the field to a register address
all use an address higher than 0x7fffffff, which is thus considered by
the driver as invalid. The feature is thus never used, remove it.
The feature could be implemented properly in the future using the
pinctrl and GPIO APIs if desired.
While at it, don't set the field to SCIx_NOT_SUPPORTED (-1) either,
leaving it unset leads to the same result. This will allow removing the
SCIx_NOT_SUPPORTED macro.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flag is set by the driver internally, don't set it in platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCIF ports on sh7264 and sh7269 don't support the TOIE bit according
to the datasheets.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The scscr platform data field is used by the driver in three locations.
One of them masks out all bits except SCSCR_REIE. The two other are the
set_termios handler and the console write handler.
The set_termios handler calls sci_start_rx() to enable the receiver,
which sets the RIE bit unconditionally. It then calls sci_port_disable()
that effectively disables both the transmitter and the receiver. The
TIE bit will thus get set later when the serial cores reenables the
serial port.
The console write handler runs with interrupts disabled, and saves and
restores the SCSCR register value. The RIE and TIE bits are thus not
needed there.
The bits are thus not necessary in platform data, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bits are set by the driver internally, don't set them in platform
data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UPF_BOOT_AUTOCONF platform data flag is set by all platforms,
hardcode it.
The UPF_IOREMAP flag is set by a single SH platform and thus needs to be
kept. However, for ARM platforms, we can base the decision on whether an
OF node is present and bypass the platform data flags completely.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Transmit Enable and Receive Enable bits are set in the scscr field
of all instances of the sh-sci platform data. Set them in the driver
directly to prepare for their removal from platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following sparse warning:
drivers/net/wireless/ath/ath6kl/sdio.c:716:55: warning:
Using plain integer as NULL pointer
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is needed for WiFi to work e.g. on DIR-615 rev.H1 which got
external RF power amplifiers connected to the WiSoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simple patch to correct HT20/HT40 filter setting.
Tested with Rt3290, Rt3352 and Rt5350
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since rt2800pci update beacon settings asynchronously from
tbtt tasklet, without beacon_skb_mutex protection, number of
currently active beacons entries can be different than
number pointed by rt2x00dev->intf_beaconing. Remove warning
about that inconsistency.
Reported-by: evaxige@qq.com
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We may want to use Open Firmware for other devices than just SDIO ones.
In future we may want to support more Broadcom properties so there is
really no reason for such limitation.
Call brcmf_of_probe for all kind of devices & move extra conditions to
the body of that funcion.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function lbs_cmd_802_11_sleep_params() always return 0, even if the call
to lbs_cmd_with_response() fails. In this case, the parameter @sp will
keep uninitialized. Because the return value is 0, its caller (say
lbs_sleepparams_read()) will not detect the error, and will copy the
uninitialized stack memory to user sapce, resulting in stack information
leak. To avoid the bug, this patch returns variable ret (which takes
the return value of lbs_cmd_with_response()) instead of 0.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188451
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some usermode helper applications are defined at kernel build time, while
others can be changed at runtime. To provide a sane way to filter these, add a
new kernel option "STATIC_USERMODEHELPER". This option routes all
call_usermodehelper() calls through this binary, no matter what the caller
wishes to have called.
The new binary (by default set to /sbin/usermode-helper, but can be changed
through the STATIC_USERMODEHELPER_PATH option) can properly filter the
requested programs to be run by the kernel by looking at the first argument
that is passed to it. All other options should then be passed onto the proper
program if so desired.
To disable all call_usermodehelper() calls by the kernel, set
STATIC_USERMODEHELPER_PATH to an empty string.
Thanks to Neil Brown for the idea of this feature.
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a number of usermode helper binaries that are "hard coded" in
the kernel today, so mark them as "const" to make it harder for someone
to change where the variables point to.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Sailer <t.sailer@alumni.ethz.ch>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Jeff Layton <jlayton@poochiereds.net>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor write_vmem() for sake of readability.
While here, fix indentation in one comment.
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is 64x48 display exists. In order to support that set multiplexer
to 48 pixels and window address to proper position in the graphic display
data RAM.
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kstrto*() functions return proper error code.
Do propogate it to the user.
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to duplicate what SPI core already does, i.e. mapping buffers
for DMA capable transfers.
Remove all related pices of code.
Note, that code, besides its redundancy, was buggy: DMA address potentially can
be 0, SPI slave device has nothing to do with DMA capable device properties and
DMA mask in particular.
Suggested-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First of all, fbtft in current state doesn't allow to override GPIOs to be
optional, like "reset" one. It might be a bug somewhere, but rather out of
scope of this fix.
Second, not all GPIOs available on the board would be SoC based, some of them
might sit on I2C GPIO expanders, for example, on Intel Edison/Arduino, and thus
any communication with them might sleep.
Besides that using udelay() and mdelay() is kinda resource wasteful.
Summarize all of the above, convert fbtft_reset() function to non-atomic
variant by using gpio_set_value_cansleep(), usleep_range(), and msleep().
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is in preparation for making it so that usermode helper programs
can't be changed, if desired, by userspace. We will tackle the mess of
cleaning up the write-ability of argv and env later, that's going to
take more work, for much less gain...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the latest change to make sure the compiler actually does a memset,
it is now smart enough to flag the stack overflow at compile time,
at least with gcc-7.0:
drivers/misc/lkdtm_bugs.c: In function 'lkdtm_CORRUPT_STACK':
drivers/misc/lkdtm_bugs.c:88:144: warning: 'memset' writing 64 bytes into a region of size 8 overflows the destination [-Wstringop-overflow=]
To outsmart the compiler again, this moves the memset into a noinline
function where (for now) it doesn't see that we intentionally write
broken code here.
Fixes: c55d240003 ("lkdtm: Prevent the compiler from optimising lkdtm_CORRUPT_STACK()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stm is automatically enabled when an application sets the policy
via ->link() call back by using coresight_enable(), which keeps the
refcount of the current users of the STM. However, the unlink() callback
issues stm_disable() directly, which leaves the STM turned off, without
the coresight layer knowing about it. This prevents any further uses
of the STM hardware as the coresight layer still thinks the STM is
turned on and doesn't enable the hardware when required. Even manually
enabling the STM via sysfs can't really enable the hw.
e.g,
$ echo 1 > $CS_DEVS/$ETR/enable_sink
$ mkdir -p $CONFIG_FS/stp-policy/$source.0/stm_test/
$ echo 32768 65535 > $CONFIG_FS/stp-policy/$source.0/stm_test/channels
$ echo 64 > $CS_DEVS/$source/traceid
$ ./stm_app
Sending 64000 byte blocks of pattern 0 at 0us intervals
Success to map channel(32768~32783) to 0xffffa95fa000
Sending on channel 32768
$ dd if=/dev/$ETR of=~/trace.bin.1
597+1 records in
597+1 records out
305920 bytes (306 kB) copied, 0.399952 s, 765 kB/s
$ ./stm_app
Sending 64000 byte blocks of pattern 0 at 0us intervals
Success to map channel(32768~32783) to 0xffff7e9e2000
Sending on channel 32768
$ dd if=/dev/$ETR of=~/trace.bin.2
0+0 records in
0+0 records out
0 bytes (0 B) copied, 0.0232083 s, 0.0 kB/s
Note that we don't get any data from the ETR for the second session.
Also dmesg shows :
[ 77.520458] coresight-tmc 20800000.etr: TMC-ETR enabled
[ 77.537097] coresight-replicator etr_replicator@20890000: REPLICATOR enabled
[ 77.558828] coresight-replicator main_replicator@208a0000: REPLICATOR enabled
[ 77.581068] coresight-funnel 208c0000.main_funnel: FUNNEL inport 0 enabled
[ 77.602217] coresight-tmc 20840000.etf: TMC-ETF enabled
[ 77.618422] coresight-stm 20860000.stm: STM tracing enabled
[ 139.554252] coresight-stm 20860000.stm: STM tracing disabled
# End of first tracing session
[ 146.351135] coresight-tmc 20800000.etr: TMC read start
[ 146.514486] coresight-tmc 20800000.etr: TMC read end
# Note that the STM is not turned on via stm_generic_link()->coresight_enable()
# and hence none of the components are turned on.
[ 152.479080] coresight-tmc 20800000.etr: TMC read start
[ 152.542632] coresight-tmc 20800000.etr: TMC read end
This patch fixes the problem by balancing the unlink operation by using
the coresight_disable(), keeping the coresight layer in sync with the
hardware state and thus allowing normal usage of the STM component.
Fixes: commit 237483aa5c ("coresight: stm: adding driver for CoreSight STM component")
Cc: Pratik Patel <pratikp@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # 4.7+
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Reported-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aemif driver can now access struct of_dev_auxdata (using platform
data).
Add the device id to the clock lookup table for the nand clock and
create a separate lookup table for aemif subnodes.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TI aemif driver creates its own subnodes of the device tree in order
to guarantee that all child devices are probed after the AEMIF timing
parameters are configured.
Some devices (e.g. da850) use struct of_dev_auxdata for clock lookup
but nodes created from within the aemif driver can't access the lookup
table.
Create a platform data structure that holds a pointer to
of_dev_auxdata so that we can use it with of_platform_populate().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PC/104 form factor devices serve a specific niche of embedded system
users; most Linux users will not have PC/104 form factor devices. This
patch introduces the PC104 Kconfig option, which should be used to
filter PC/104 specific device drivers and options, so that only those
users interested in PC/104 related options are exposed to them.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the PM8994 regulators found on msm8992,
msm8994 and msm8996 platforms.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[bjorn: Add DT binding doc and vdd_lvs1_2 supply]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>