Keep per Tx-queue error count on Head-Of-Line Blocking due to frame
size(HLBF) error. The MAC raises HLBF error on one or more queues
when none of the time Intervals of open-gates in the GCL is greater
than or equal to the duration needed for frame transmission and by
default drops those packets that causes HLBF error. EST_FRM_SZ_ERR
register provides the One Hot encoded Queue numbers that have the
Frame Size related error.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring queueMaxSDU. As DWMAC IPs doesn't support
queueMaxSDU table handle this in the SW. The maximum 802.3 frame size
that is allowed to be transmitted by any queue is queueMaxSDU +
16 bytes (i.e. 6 bytes SA + 6 bytes DA + 4 bytes FCS).
Inspired from intel i225 driver.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BeagleV Starlight SBC uses a Microchip KSZ9031RNXCA PHY supporting
RGMII-ID which doesn't require any particular setup, other than defining
a reset gpio, as opposed to VisionFive V1 for which the RX internal
delay had to be adjusted.
Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The StarFive VisionFive V1 SBC uses a Motorcomm YT8521 PHY supporting
RGMII-ID, but requires manual adjustment of the RX internal delay to
work properly.
The default RX delay provided by the driver is 1.95 ns, which proves to
be too high. Applying a 50% reduction seems to mitigate the issue.
Also note this adjustment is not necessary on BeagleV Starlight SBC,
which uses a Microchip PHY. Hence, there is no indication of a
misbehaviour on the GMAC side, but most likely the issue stems from
the Motorcomm PHY.
While at it, drop the redundant gpio include, which is already provided
by jh7100-common.dtsi.
Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add pinmux configuration for DWMAC found on the JH7100 based boards and
enable the related DT node, providing a basic PHY configuration.
Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Provide the sysmain and gmac DT nodes supporting the DWMAC found on the
StarFive JH7100 SoC.
Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
This test validates per-band packet limits in FQ. Packets are dropped
rather than enqueued if the limit for their band is reached.
This test is timing sensitive. It queues packets in FQ with a future
delivery time to fill the qdisc.
The test failed in a virtual environment (vng). Increase the delays
to make it more tolerant to environments with timing variance.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ASMedia have confirmed that all ASM106x parts currently listed in
ahci_pci_tbl[] suffer from the 43-bit DMA address limitation that we ran
into on the ASM1061, and therefore, we need to apply the quirk added by
commit 20730e9b27 ("ahci: add 43-bit DMA address quirk for ASMedia
ASM1061 controllers") to the other supported ASM106x parts as well.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-ide/ZbopwKZJAKQRA4Xv@x1-carbon/
Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
[cassel: add link to ASMedia confirmation email]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Benjamin Poirier says:
====================
selftests: Add TEST_INCLUDES directive and adjust tests to use it
After commit 25ae948b44 ("selftests/net: add lib.sh") but before commit
2114e83381 ("selftests: forwarding: Avoid failures to source
net/lib.sh"), some net selftests encountered errors when they were being
exported and run. This was because the new net/lib.sh was not exported
along with the tests. The errors were crudely avoided by duplicating some
content between net/lib.sh and net/forwarding/lib.sh in 2114e83381.
In order to restore the sourcing of net/lib.sh from net/forwarding/lib.sh
and remove the duplicated content, this series introduces a new selftests
Makefile variable to list extra files to export from other directories and
makes use of it to avoid reintroducing the errors mentioned above.
v2:
* "selftests: Introduce Makefile variable to list shared bash scripts"
Fix rst syntax in Documentation/dev-tools/kselftest.rst (Jakub Kicinski)
v1:
* "selftests: Introduce Makefile variable to list shared bash scripts"
Changed TEST_INCLUDES to take relative paths, like other TEST_* variables.
Paths are adjusted accordingly in the subsequent patches. (Vladimir Oltean)
* selftests: bonding: Change script interpreter
selftests: forwarding: Remove executable bits from lib.sh
Removed from this series, submitted separately.
Since commit 2114e83381 ("selftests: forwarding: Avoid failures to source
net/lib.sh") resolved the test errors, this version of the series is
focused on removing the duplication that was added in that commit. Directly
rebasing the series would reintroduce the problems that 2114e83381
avoided before fixing them again. In order to prevent such breakage partway
through the series, patches are reordered and content changed slightly but
there is no diff at the end compared with the simple rebasing approach. I
have dropped most review tags on account of this reordering.
RFC:
https://lore.kernel.org/netdev/20231222135836.992841-1-bpoirier@nvidia.com/
Link: https://lore.kernel.org/netdev/ZXu7dGj7F9Ng8iIX@Laptop-X1/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 25ae948b44 ("selftests/net: add lib.sh") added net/lib.sh to
contain code shared by tests under net/ and net/forwarding/. However, this
caused issues with selftests from directories other than net/forwarding/,
in particular those under drivers/net/. Those issues were avoided in a
simple way by duplicating some content in commit 2114e83381 ("selftests:
forwarding: Avoid failures to source net/lib.sh").
In order to remove the duplicated content, restore the inclusion of
net/lib.sh from net/forwarding/lib.sh but with the following changes:
* net/lib.sh is imported through the net_forwarding_dir path
The original expression "source ../lib.sh" would look for lib.sh in the
directory above the script file's one, which did not work for tests under
drivers/net/.
* net/lib.sh is added to TEST_INCLUDES
Since net/forwarding/lib.sh now sources net/lib.sh, both of those files
must be exported along with tests which source net/forwarding/lib.sh.
Suggested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following code which is part of lib.sh:
relative_path="${BASH_SOURCE%/*}"
if [[ "$relative_path" == "${BASH_SOURCE}" ]]; then
relative_path="."
fi
reimplements functionality that is part of `dirname`:
$ dirname ""
.
To avoid this duplication, replace "relative_path" by "net_forwarding_dir",
a new variable defined using dirname.
Furthermore, to avoid the potential confusion about what "relative_path" is
about (cwd, test script directory or test library directory), define
"net_forwarding_dir" as the absolute path to net/forwarding/.
Tested-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa tests which are symlinks of tests from net/forwarding/ (like
tc_actions.sh) become regular files after export (because `rsync
--copy-unsafe-links` is used) and expect to source lib.sh
(net/forwarding/lib.sh) from the same directory.
In the last patch of this series, net/forwarding/lib.sh will source lib.sh
from its parent directory (ie. net/lib.sh). This would not work for dsa
tests because net/lib.sh is not present under drivers/net/.
Since the tests in net/forwarding/ are not meant to be copied and run from
another directory, as a preparation for that last patch, replace the test
symlinks by a wrapper script which runs the original tests under
net/forwarding/. Following from that, the links to shared library scripts
in dsa/ are no longer used so remove them and add all the original files
needed from parent directories to TEST_INCLUDES.
Suggested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid duplicated files when both the team and bonding tests are
exported together, add lag_lib.sh to TEST_INCLUDES.
Do likewise for net/forwarding/lib.sh regarding team and forwarding tests.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid duplicated files when both the bonding and forwarding
tests are exported together, add net/forwarding/lib.sh to TEST_INCLUDES and
include it via its relative path.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some tests written in bash source other files in a parent directory. For
example, drivers/net/bonding/dev_addr_lists.sh sources
net/forwarding/lib.sh. If a subset of tests is exported and run outside the
source tree (for example by using `make -C tools/testing/selftests gen_tar
TARGETS="drivers/net/bonding"`), these other files must be made available
as well.
Commit ae108c48b5 ("selftests: net: Fix cross-tree inclusion of scripts")
addressed this problem by symlinking and copying the sourced files but this
only works for direct dependencies. Commit 25ae948b44 ("selftests/net:
add lib.sh") changed net/forwarding/lib.sh to source net/lib.sh. As a
result, that latter file must be included as well when the former is
exported. This was not handled and was reverted in commit 2114e83381
("selftests: forwarding: Avoid failures to source net/lib.sh"). In order to
allow reinstating the inclusion of net/lib.sh from net/forwarding/lib.sh,
add a mechanism to list dependent files in a new Makefile variable and
export them. This allows sourcing those files using the same expression
whether tests are run in-tree or exported.
Dependencies are not resolved recursively so transitive dependencies must
be listed in TEST_INCLUDES. For example, if net/forwarding/lib.sh sources
net/lib.sh; the Makefile related to a test that sources
net/forwarding/lib.sh from a parent directory must list:
TEST_INCLUDES := \
../../../net/forwarding/lib.sh \
../../../net/lib.sh
v2:
Fix rst syntax in Documentation/dev-tools/kselftest.rst (Jakub Kicinski)
v1 (from RFC):
* changed TEST_INCLUDES to take relative paths, like other TEST_* variables
(Vladimir Oltean)
* preserved common "$(MAKE) OUTPUT=... -C ... target" ordering in Makefile
(Petr Machata)
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing quirk to enable support for the StarFive JH7100 SoC.
Additionally, for greater flexibility in operation, allow using the
rgmii-rxid and rgmii-txid phy modes.
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Synopsys DesignWare MAC found on StarFive JH7100 SoC is mostly
similar to the newer JH7110, but it requires only two interrupts and a
single reset line, which is 'ahb' instead of the commonly used
'stmmaceth'.
Since the common binding 'snps,dwmac' allows selecting 'ahb' only in
conjunction with 'stmmaceth', extend the logic to also permit exclusive
usage of the 'ahb' reset name. This ensures the following use cases are
supported:
JH7110: reset-names = "stmmaceth", "ahb";
JH7100: reset-names = "ahb";
other: reset-names = "stmmaceth";
Also note the need to use a different dwmac fallback, as v5.20 applies
to JH7110 only, while JH7100 relies on v3.7x.
Additionally, drop the reset description items from top-level binding as
they are already provided by the included snps,dwmac schema.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we assume all the port pins are sequential ie always PX_0 to
PX_n (n=1..7) exist, but on RZ/Five SoC we have additional pins P19_1 to
P28_5 which have holes in them, for example only one pin on port19 is
available and that is P19_1 and not P19_0. So to handle such cases
include pinmap for each port which would indicate the pin availability
on each port. As the pincount can be calculated based on pinmap drop this
from RZG2L_GPIO_PORT_PACK() macro.
Previously we had a max of 7 pins on each port but on RZ/Five Port-20
has 8 pins, so move the single pin configuration to BIT(63).
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129135556.63466-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
If the number of provided enum IDs in a variable width config register
description does not match the expected number, the checker uses the
expected number for validating the individual enum IDs.
However, this may cause out-of-bounds accesses on the array holding the
enum IDs, leading to bogus enum_id conflict warnings. Worse, if the bug
is an incorrect bit field description (e.g. accidentally using "12"
instead of "-12" for a reserved field), thousands of warnings may be
printed, overflowing the kernel log buffer.
Fix this by limiting the enum ID check to the number of provided enum
IDs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c7385f44f2faebb8856bcbb4e908d846fc1531fb.1705930809.git.geert+renesas@glider.be
Commit d3aaa7203a ("pinctrl: renesas: rzg2l: Add pin configuration
support for pinmux groups") introduced the possibility to parse pin
configuration for pinmux groups. It did that by calling
rzg2l_map_add_config() at the end of rzg2l_dt_subnode_to_map() and
jumping to the remove_group label in case rzg2l_map_add_config() failed.
But if that happens, the mutex will already be unlocked, thus this it will
lead to double mutex unlock operation. To fix this move the
rzg2l_map_add_config() call just after all the name argument is ready and
before the mutex is locked. There is no harm in doing this, as this only
parses the data from device tree that will be further processed by
pinctrl core code.
Fixes: d3aaa7203a ("pinctrl: renesas: rzg2l: Add pin configuration support for pinmux groups")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/f8c3a3a0-7c48-4e40-8af0-ed4e9d9b049f@moroto.mountain
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240115153453.99226-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car V4H and V4M have a second Frequency Control Register C.
Add support for this by treating bit field offsets beyond 31 as
referring to the second register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/f64d5573a92a18505619ff0ff808d50cfc2bde55.1706194617.git.geert+renesas@glider.be
Clock and Power Domain definitions for the Renesas R-Car V4M (R8A779H0)
SoC, shared by driver and DT source files.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZboeXgAKCRCKwlD9ZEnx
cDs1AP9eLrF6KeaemzlJSjTrspPX1BC7lyuL2n0d2o4nQWT3MwD+OBw8voT7wuIR
7E4Ax7vz+bo7lGRM50vR4VReW1Ik9gY=
=mi8p
-----END PGP SIGNATURE-----
Merge tag 'renesas-r8a779h0-dt-binding-defs-tag' into renesas-clk-for-v6.9
Renesas R-Car V4M DT Binding Definitions
Clock and Power Domain definitions for the Renesas R-Car V4M (R8A779H0)
SoC, shared by driver and DT source files.
Add CRU clock and reset entries to CPG driver.
CRU_SYSCLK and CRU_VCLK clocks need to be turned ON/OFF in particular
sequence for the CRU block hence add these clocks to
r9a07g043_no_pm_mod_clks[] array and pass it as part of CPG data for
RZ/G2UL SoCs.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240123114415.290918-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RZ/G3S has a watchdog module accessible by the Cortex-A core. Add clock
and reset support for it.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240122111115.2861835-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The activation for Scan at Field (SAF) includes a parameter to make
microcode wait for both threads to join. It's preferable to perform an
entry rendezvous before the activation to ensure that they start the
`wrmsr` close enough to each other. In some cases it has been observed
that one of the threads might be just a bit late to arrive. An entry
rendezvous reduces the likelihood of these cases occurring.
Add an entry rendezvous to ensure the activation on both threads happen
close enough to each other.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20240125082254.424859-6-ashok.raj@intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
ARRAY_BIST requires the test to be invoked only from one of the HT
siblings of a core. If the other sibling was in mwait(), that didn't
permit the test to complete and resulted in several retries before the
test could finish.
The exit rendezvous was introduced to keep the HT sibling busy until
the primary CPU completed the test to avoid those retries. What is
actually needed is to ensure that both the threads rendezvous *before*
the wrmsr to trigger the test to give good chance to complete the test.
The `stop_machine()` function returns only after all the CPUs complete
running the function, and provides an exit rendezvous implicitly.
In kernel/stop_machine.c::multi_cpu_stop(), every CPU in the mask
needs to complete reaching MULTI_STOP_RUN. When all CPUs complete, the
state machine moves to next state, i.e MULTI_STOP_EXIT. Thus the
underlying API stop_core_cpuslocked() already provides an exit
rendezvous.
Add the rendezvous earlier in order to ensure the wrmsr is triggered
after all CPUs reach the do_array_test(). Remove the exit rendezvous
since stop_core_cpuslocked() already guarantees that.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20240125082254.424859-5-ashok.raj@intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add the current batch number in the trace output. When there are
failures, it's important to know which test content resulted in failure.
# TASK-PID CPU# ||||| TIMESTAMP FUNCTION
# | | | ||||| | |
migration/0-18 [000] d..1. 527287.084668: ifs_status: batch: 02, start: 0000, stop: 007f, status: 0000000000007f80
migration/128-785 [128] d..1. 527287.084669: ifs_status: batch: 02, start: 0000, stop: 007f, status: 0000000000007f80
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20240125082254.424859-4-ashok.raj@intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Enable the trace function on all HT threads. Currently, the trace is
called from some arbitrary CPU where the test was invoked.
This change gives visibility to the exact errors as seen by each
participating HT threads, and not just what was seen from the primary
thread.
Sample output below.
# TASK-PID CPU# ||||| TIMESTAMP FUNCTION
# | | | ||||| | |
migration/0-18 [000] d..1. 527287.084668: start: 0000, stop: 007f, status: 0000000000007f80
migration/128-785 [128] d..1. 527287.084669: start: 0000, stop: 007f, status: 0000000000007f80
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20240125082254.424859-3-ashok.raj@intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Follow the docs at Documentation/bpf/kfuncs.rst:
- declare the function with `__bpf_kfunc`
- disables missing prototype warnings, which allows to remove them from
include/linux/hid-bpf.h
Removing the prototypes is not an issue because we currently have to
redeclare them when writing the BPF program. They will eventually be
generated by bpftool directly AFAIU.
Link: https://lore.kernel.org/r/20240124-b4-hid-bpf-fixes-v2-3-052520b1e5e6@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Turns out that I got my reference counts wrong and each successful
bus_find_device() actually calls get_device(), and we need to manually
call put_device().
Ensure each bus_find_device() gets a matching put_device() when releasing
the bpf programs and fix all the error paths.
Cc: <stable@vger.kernel.org>
Fixes: f5c27da4e3 ("HID: initial BPF implementation")
Link: https://lore.kernel.org/r/20240124-b4-hid-bpf-fixes-v2-2-052520b1e5e6@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
When the kfunc hid_bpf_attach_prog() is called, we called twice fdget():
one for fetching the type of the bpf program, and one for actually
attaching the program to the device.
The problem is that between those two calls, we have no guarantees that
the prog_fd is still the same file descriptor for the given program.
Solve this by calling bpf_prog_get() earlier, and use this to fetch the
program type.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/bpf/CAO-hwJJ8vh8JD3-P43L-_CLNmPx0hWj44aom0O838vfP4=_1CA@mail.gmail.com/T/#t
Cc: <stable@vger.kernel.org>
Fixes: f5c27da4e3 ("HID: initial BPF implementation")
Link: https://lore.kernel.org/r/20240124-b4-hid-bpf-fixes-v2-1-052520b1e5e6@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Relax DEVX access upon modify commands to be UVERBS_ACCESS_READ.
The kernel doesn't need to protect what firmware protects, or what
causes no damage to anyone but the user.
As firmware needs to protect itself from parallel access to the same
object, don't block parallel modify/query commands on the same object in
the kernel side.
This change will allow user space application to run parallel updates to
different entries in the same bulk object.
Tested-by: Tamar Mashiah <tmashiah@nvidia.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Reviewed-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://lore.kernel.org/r/7407d5ed35dc427c1097699e12b49c01e1073406.1706433934.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
debugfs entries for RRoCE general CC parameters must be exposed only when
they are supported, otherwise when accessing them there may be a syndrome
error in kernel log, for example:
$ cat /sys/kernel/debug/mlx5/0000:08:00.1/cc_params/rtt_resp_dscp
cat: '/sys/kernel/debug/mlx5/0000:08:00.1/cc_params/rtt_resp_dscp': Invalid argument
$ dmesg
mlx5_core 0000:08:00.1: mlx5_cmd_out_err:805:(pid 1253): QUERY_CONG_PARAMS(0x824) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x325a82), err(-22)
Fixes: 66fb1d5df6 ("IB/mlx5: Extend debug control for CC parameters")
Reviewed-by: Edward Srouji <edwards@nvidia.com>
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Link: https://lore.kernel.org/r/e7ade70bad52b7468bdb1de4d41d5fad70c8b71c.1706433934.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When DT overlay is applied at run time compatible string or model AFAIK is
not updated. But when fdtoverlay tool is used it actually creates full
description for used SOM and carrier card(CC). That's why there is no
reason to use generic SOM name and its compatible strings because they are
not properly reflected in newly created DT.
Composing dt overlays together was introduced by commit 7a4c31ee87
("arm64: zynqmp: Add support for Xilinx Kria SOM board") and later renamed
by commit 45fe0dc4ea ("arm64: xilinx: Use zynqmp prefix for SOM dt
overlays").
DTB selection is done prior booting OS that's why there is no need to do
run time composition for SOM and CC combination. And user space can use
compatible string and all listed revisions to figured it out which SOM and
CC combinations OS is running at.
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/14c184225cc4f0a61da5f8c98bc0767f8deba0df.1706019781.git.michal.simek@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Revision 2 is SW compatible with revision 1 but it is necessary to reflect
it in model and compatible properties which are parsed by user space.
Rev 2 has improved a power on boot reset and MIO34 shutdown glich
improvement done via an additional filter in the GreenPak chip.
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/90e1a393154c3d87e8ee7dc9eef07fc937c1eaf7.1706019397.git.michal.simek@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Compatible string doesn't really match with compatible string listed in the
driver itself. While binding was converted from txt to yaml
xlnx,zynq-pinctrl was listed as compatible string but example was using
xlnx,pinctrl-zynq and also this string is used in all DTSes.
xlnx,zynq-pinctrl is used only in dt binding and not present in any DT
which is stable for quite a long time that's why use old compatible string
and update binding document instead of starting to use unused compatible
string.
Fixes: 153df45acd ("dt-bindings: pinctrl: pinctrl-zynq: Convert to yaml")
Signed-off-by: Michal Simek <michal.simek@amd.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/c1307a4dd5e30290acacc786cb2170deb9eaa539.1706087258.git.michal.simek@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Check against ARRAY_SIZE() which is the number of elements instead of
sizeof() which is the number of bytes.
Fixes: 453f0ae797 ("RAS/AMD/ATL: Add MI300 support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/279c8b5e-6c00-467a-9071-9c67926abea4@moroto.mountain