Add clock-frequency to MDIO node to set the MDC rate to 6.25Mhz instead
of using the default value of 390KHz from MDIO default divider.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240131022731.2118-1-ansuelsmth@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
If cluster domain idle state is enabled on the RB1, the board becomes
significantly less responsive. Under certain circumstances (if some of
the devices are disabled in kernel config) the board can even lock up.
It seems this is caused by the MPM not updating wakeup timer during CPU
idle (in the same way the RPMh updates it when cluster idle state is
entered).
Disable cluster domain idle for the RB1 board until MPM driver is fixed
to cooperate with the CPU idle states.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240130-rb1-suspend-cluster-v2-1-5bc1109b0869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the GPU node for the Adreno 506 found on this family of SoCs. The
clock speeds are a bit different per SoC variant, SDM450 maxes out at
600MHz while MSM8953 (= SDM625) goes up to 650MHz and SDM632 goes up to
725MHz.
To achieve this, create a new sdm450.dtsi to hold the 600MHz OPP and
use the new dtsi for sdm450-motorola-ali.
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Co-developed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240125-msm8953-gpu-v1-2-f6493a5951f3@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
With this reset we can avoid situations like IRQ storms from DSI host
before it even started probing (because boot-loader left DSI IRQs on).
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240125-msm8953-mdss-reset-v2-3-fd7824559426@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add new defines for some more BCRs found on MSM8953.
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
[luca: expand commit message, add more resets]
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20240125-msm8953-mdss-reset-v2-1-fd7824559426@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the remaining Audio nodes on the SM8650-QRD board including:
- Qualcomm Aqstic WCD9395 audio codec on the RX & TX Soundwire interfaces
- WSA8845 Left & Right Speakers
- Link the WCD9395 Codec node to the WCD9395 USB SubSystem node to handle
the USB-C Audio Accessory Mode events & lane swapping
- Sound card with routing for Speakers and Microphones
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240125-topic-sm8650-upstream-audio-dt-v1-1-c24d23ae5763@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add dma-coherent property to fastRPC context bank nodes to pass dma
sequence test in fastrpc sanity test, ensure that data integrity is
maintained during DMA operations.
Signed-off-by: Ling Xu <quic_lxu5@quicinc.com>
Link: https://lore.kernel.org/r/20240125102413.3016-3-quic_lxu5@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add dma-coherent property to fastRPC context bank nodes to pass dma
sequence test in fastrpc sanity test, ensure that data integrity is
maintained during DMA operations.
Signed-off-by: Ling Xu <quic_lxu5@quicinc.com>
Link: https://lore.kernel.org/r/20240125102413.3016-2-quic_lxu5@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add proper audio routes for onboard analogue microphones AMIC[1345] -
MIC biases and route from TX macro codec to WCD9385 audio codec.
This should bring AMIC1, AMIC2 (headphones), AMIC3, AMIC4 and AMIC5
onboard microphones to work, although was not tested on the hardware.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240124164505.293202-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add proper audio routes for onboard analogue microphones AMIC[1345] -
MIC biases and route from TX macro codec to WCD9385 audio codec.
This finally brings AMIC1, AMIC3, AMIC4 and AMIC5 onboard microphones to
work. AMIC2 (headphones) should be fine well, however it didn't work
during tests, probably because of incomplete USB switch.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240124164505.293202-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
WCD9385 audio codec TX port mapping was copied form HDK8450, but in fact
it is offset by one. Correct it to fix recording via analogue
microphones.
The change is based on QRD8550 and should be correct here as well, but
was not tested on MTP8550.
Cc: stable@vger.kernel.org
Fixes: a541667c86 ("arm64: dts: qcom: sm8550-mtp: add WCD9385 audio-codec")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240124164505.293202-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
WCD9385 audio codec TX port mapping was copied form HDK8450, but in fact
it is offset by one. Correct it to fix recording via analogue
microphones.
Cc: stable@vger.kernel.org
Fixes: 83fae950c9 ("arm64: dts: qcom: sm8550-qrd: add WCD9385 audio-codec")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240124164505.293202-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the definitions for the various thermal zones found on the SM6350
SoC. Hooking up GPU and CPU cooling can limit the clock speeds there to
reduce the temperature again to good levels.
Most thermal zones only have one critical temperature configured at
125°C which can be mostly considered a placeholder until those zones can
be hooked up to cooling.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240124-sm6350-tsens-v1-1-d37ec82140af@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The USB3 PHY on the SM6115 platform doesn't have built-in
PCS_MISC_CLAMP_ENABLE register. Instead clamping is handled separately
via the register in the TCSR space. Declare corresponding register.
Fixes: 9dd5f6dba7 ("arm64: dts: qcom: sm6115: Add USB SS qmp phy node")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-6-a950c223f10f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The USB3 PHY on the QCM2290 platform doesn't have built-in
PCS_MISC_CLAMP_ENABLE register. Instead clamping is handled separately
via the register in the TCSR space. Declare corresponding register.
Fixes: 0c55f6229b ("arm64: dts: qcom: qcm2290: Add USB3 PHY")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-5-a950c223f10f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The USB3 PHY on the MSM8998 platform doesn't have built-in
PCS_MISC_CLAMP_ENABLE register. Instead clamping is handled separately
via the register in the TCSR space. Declare corresponding register.
Fixes: 026dad8f58 ("arm64: dts: qcom: msm8998: Add USB-related nodes")
Cc: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-4-a950c223f10f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
QCM6490 uses Trustzone as firmware whereas SC7280 uses arm trusted firmware.
The PSCI suspend param and the number of domain-idle-states supported is
different in Trustzone for cluster sleep.
Move the arm trusted firmware supported domain-idle-states in chrome specific
sc7280-chrome-common.dtsi and add the Trustzone supported sleep states as default
domain-idle-states in sc7280.dtsi
Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20240109-qcm6490_cluster_sleep-v2-1-8f94f1ad188d@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The board-specific (electrical) configuration was removed from PM660L in
90ba636e40 ("arm64: dts: qcom: pm660l: Remove board-specific WLED
configuration") as it is platform-dependent. We reintroduce it here in
the Nile board configuration (with a slightly lower current limit, as
per downstream DT sources) and enable it for use in the dsi0 node.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20240204-sdm630-nile-wled-v1-1-9f5c4f8147f2@somainline.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The idea impressed in the commit b32e592d3c ("devicetree: bindings:
Document qcom board compatible format") never got actually adopted. As
can be seen from the existing board DT files, no device actually used
the PMIC / foundry / version parts of the compatible string. Drop this
compatibility string description to avoid possible confusion and keep
just the generic terms and the SoC list.
Fixes: b32e592d3c ("devicetree: bindings: Document qcom board compatible format")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20240204-qcom-drop-compat-v1-1-69d6cd92aa0e@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The qlink_logging memory region is also used by the modem firmware,
add it to the reserved memories and add it to the MPSS memory regions.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/r/20240123-topic-sm8650-upstream-remoteproc-v7-4-61283f50162f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add Inline Crypto Engine reg and clocks in MMC node and enable CQE
support as Inline Crypto Engine requires CQE to be enabled.
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Link: https://lore.kernel.org/r/20231215095339.3055554-1-quic_viswanat@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add nodes for four WSA8845 speakers. Unlike previous boards like
SM8550-QRD, this board has four speakers spread over two Soundwire buses
instead of two speakers on one bus. Each pair of speakers shares the
reset GPIO thus pinctrl property is only in one of them.
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add Qualcomm Aqstic WCD9385 audio codec on two Soundwire interfaces: RX
and TX.
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add nodes for LPASS Soundwire v2.0.0 controllers. Difference against
SM8550:
1. Update port configs to match reference implementation,
2. LPASS TLMM GPIO14 is not used as WCD_SR_TX_DATA2 pin but as GPIO
(camera).
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the Low Power Audio SubSystem (LPASS) / ADSP audio codec macros on
Qualcomm SM8650. The nodes are exactly the same as on SM8550 and
SM8650.
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the Low Power Audio SubSystem Low Power Island (LPASS LPI) pin
controller device node as part of audio subsystem in Qualcomm X1E80100
SoC.
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231212125632.54021-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the ADSP Generic Packet Router (GPR) device node as part of audio
subsystem in Qualcomm X1E80100 SoC.
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231212125632.54021-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the required nodes to support display on X1E80100.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-8-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add nodes for PCIe 4 and 6 controllers and their PHYs for X1E80100 platform.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-7-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add nodes for all USB controllers and their PHYs for X1E80100 platform.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-6-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add ADSP and CDSP remoteproc nodes on X1E80100 platforms.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-4-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
SMP2P is used for interrupting and being interrupted about remoteproc
state changes related to the audio, compute and sensor subsystems.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-2-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the IPCC node, used to send and receive IPC signals with
remoteprocs.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-1-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
