commit e7bb6ad568 upstream.
The Lenovo G50-30, like other G50 models, has a Conexant codec that
requires a quirk for its inverted stereo dmic.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1249364
Reported-by: Alexander Ploumistos <alex.ploumistos@gmail.com>
Tested-by: Alexander Ploumistos <alex.ploumistos@gmail.com>
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d0c9606b31 upstream.
Add Device IDs to the Intel GPU "spurious interrupt" quirk table.
For these devices, unplugging the VGA cable and plugging it in again causes
spurious interrupts from the IGD. Linux eventually disables the interrupt,
but of course that disables any other devices sharing the interrupt.
The theory is that this is a VGA BIOS defect: it should have disabled the
IGD interrupt but failed to do so.
See f67fd55fa9 ("PCI: Add quirk for still enabled interrupts on Intel
Sandy Bridge GPUs") and 7c82126a94 ("PCI: Add new ID for Intel GPU
"spurious interrupt" quirk") for some history.
[bhelgaas: See link below for discussion about how to fix this more
generically instead of adding device IDs for every new Intel GPU. I hope
this is the last patch to add device IDs.]
Link: https://lore.kernel.org/linux-pci/1537974841-29928-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1e4c8dafbb upstream.
The 12 character temporary buffer is not necessarily long enough to hold
a 'long' value. Increase it.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1cbca5852d upstream.
Fixes two problems introduced as early as
commit 03aef4b6dc ("Staging: comedi: add ni_mio_common code"):
(1) Ensures that the last four bits of NISTC_RTSI_TRIGB_OUT_REG register is
not unduly overwritten on e-series devices. On e-series devices, the
first three of the last four bits are reserved. The last bit defines
the output selection of the RGOUT0 pin, otherwise known as
RTSI_Sub_Selection. For m-series devices, these last four bits are
indeed used as the output selection of the RTSI7 pin (and the
RTSI_Sub_Selection bit for the RGOUT0 pin is moved to the
RTSI_Trig_Direction register.
(2) Allows all 4 RTSI_BRD lines to be treated as valid sources for RTSI
lines.
This patch also cleans up the ni_get_rtsi_routing command for readability.
Fixes: 03aef4b6dc ("Staging: comedi: add ni_mio_common code")
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16:
- Use NI_RTSI_OUTPUT_RTSI_BRD_0 + n instead of NI_RTSI_OUTPUT_RTSI_BRD(n)
- Use num_configurable_rtsi_channels() instead of NISTC_RTSI_TRIG_NUM_CHAN()
- Use old_RTSI_clock_channel instead of NISTC_RTSI_TRIG_OLD_CLK_CHAN
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 32ae592036 upstream.
Shifting the u8 value[3] by an int can lead to sign-extension
overflow. For example, if value[3] is 0xff and the shift is 24 then it
is promoted to int and then the top bit is sign-extended so that all
upper 32 bits are set. Fix this by casting value[3] to a u32 before
the shift.
Detected by CoverityScan, CID#1016522 ("Unintended sign extension")
Fixes: e0d3bafd02 ("V4L/DVB (10954): Add cx231xx USB driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0004122763 upstream.
fsl_qspi_get_seqid() may return -EINVAL, but fsl_qspi_init_ahb_read()
doesn't check for error codes with the result that -EINVAL could find
itself signalled over the bus.
In conjunction with the LS1046A SoC's A-009283 errata
("Illegal accesses to SPI flash memory can result in a system hang")
this illegal access to SPI flash memory results in a system hang
if userspace attempts reading later on.
Avoid this by always checking fsl_qspi_get_seqid()'s return value
and bail out otherwise.
Fixes: e46ecda764 ("mtd: spi-nor: Add Freescale QuadSPI driver")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2d6cb6edd2 upstream.
refill->end record the last key of writeback, for example, at the first
time, keys (1,128K) to (1,1024K) are flush to the backend device, but
the end key (1,1024K) is not included, since the bellow code:
if (bkey_cmp(k, refill->end) >= 0) {
ret = MAP_DONE;
goto out;
}
And in the next time when we refill writeback keybuf again, we searched
key start from (1,1024K), and got a key bigger than it, so the key
(1,1024K) missed.
This patch modify the above code, and let the end key to be included to
the writeback key buffer.
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c157313791 upstream.
Currently, Cache missed IOs are identified by s->cache_miss, but actually,
there are many situations that missed IOs are not assigned a value for
s->cache_miss in cached_dev_cache_miss(), for example, a bypassed IO
(s->iop.bypass = 1), or the cache_bio allocate failed. In these situations,
it will go to out_put or out_submit, and s->cache_miss is null, which leads
bch_mark_cache_accounting() to treat this IO as a hit IO.
[ML: applied by 3-way merge]
Signed-off-by: tang.junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c09bcc91bb upstream.
Reading the registers without waiting for engine idle returns
unpredictable values. These unpredictable values result in display
corruption - if atyfb_imageblit reads the content of DP_PIX_WIDTH with the
bit DP_HOST_TRIPLE_EN set (from previous invocation), the driver would
never ever clear the bit, resulting in display corruption.
We don't want to wait for idle because it would degrade performance, so
this patch modifies the driver so that it never reads accelerator
registers.
HOST_CNTL doesn't have to be read, we can just write it with
HOST_BYTE_ALIGN because no other part of the driver cares if
HOST_BYTE_ALIGN is set.
DP_PIX_WIDTH is written in the functions atyfb_copyarea and atyfb_fillrect
with the default value and in atyfb_imageblit with the value set according
to the source image data.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3c6c6a7878 upstream.
The code for manual bit triple is not endian-clean. It builds the variable
"hostdword" using byte accesses, therefore we must read the variable with
"le32_to_cpu".
The patch also enables (hardware or software) bit triple only if the image
is monochrome (image->depth). If we want to blit full-color image, we
shouldn't use the triple code.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 277fcdb2cf upstream.
log_buf_len_setup does not check input argument before passing it to
simple_strtoull. The argument would be a NULL pointer if "log_buf_len",
without its value, is set in command line and thus causes the following
panic.
PANIC: early exception 0xe3 IP 10:ffffffffaaeacd0d error 0 cr2 0x0
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.19.0-rc4-yocto-standard+ #1
[ 0.000000] RIP: 0010:_parse_integer_fixup_radix+0xd/0x70
...
[ 0.000000] Call Trace:
[ 0.000000] simple_strtoull+0x29/0x70
[ 0.000000] memparse+0x26/0x90
[ 0.000000] log_buf_len_setup+0x17/0x22
[ 0.000000] do_early_param+0x57/0x8e
[ 0.000000] parse_args+0x208/0x320
[ 0.000000] ? rdinit_setup+0x30/0x30
[ 0.000000] parse_early_options+0x29/0x2d
[ 0.000000] ? rdinit_setup+0x30/0x30
[ 0.000000] parse_early_param+0x36/0x4d
[ 0.000000] setup_arch+0x336/0x99e
[ 0.000000] start_kernel+0x6f/0x4ee
[ 0.000000] x86_64_start_reservations+0x24/0x26
[ 0.000000] x86_64_start_kernel+0x6f/0x72
[ 0.000000] secondary_startup_64+0xa4/0xb0
This patch adds a check to prevent the panic.
Link: http://lkml.kernel.org/r/1538239553-81805-1-git-send-email-zhe.he@windriver.com
Cc: rostedt@goodmis.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: He Zhe <zhe.he@windriver.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 56445eef55 upstream.
Fix interrupt-out transfer length which was being set to the
transfer-buffer length rather than the size of the outgoing packet.
Note that no slab data was leaked as the whole transfer buffer is always
cleared before each transfer.
Fixes: 9aa8dae7b1 ("cypress_m8: use usb_fill_int_urb where appropriate")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c369c8db15 upstream.
A quirk in snd-usb-audio was added to automate setting sample rate to
4800k and remove the previously exposed nonfunctional microphone for
the Bowers & Wilkins PX:
commit 240a8af929https://lore.kernel.org/patchwork/patch/919689/
However the headphones where updated shortly after that to remove the
unintentional microphone functionality. I guess because of this the
headphones now crash when connecting them via USB while the quirk is
active. Dmesg:
snd-usb-audio: probe of 2-3:1.0 failed with error -22
usb 2-3: 2:1: cannot get min/max values for control 2 (id 2)
This patch removes the microfone and allows the headphones to connect
and work out of the box. It is based on the current mainline kernel
and successfully applied an tested on my machine (4.18.10.arch1-1).
Fixes: 240a8af929 ("ALSA: usb-audio: Add a quirck for B&W PX headphones")
Signed-off-by: Nicolas Huaman <nicolas@herochao.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 39f2495618 upstream.
Fix to return a negative error code from the mthca_cmd_init() error
handling case instead of 0, as done elsewhere in this function.
Fixes: 80fd823873 ("[PATCH] IB/mthca: Encapsulate command interface init")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9258227e9d upstream.
When CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not set, we look up dtl_idx in
the lppaca to determine the number of entries in the buffer. Since
lppaca is in big endian, we need to do an endian conversion before using
this in our calculation to determine the number of entries in the
buffer. Without this, we do not iterate over the existing entries in the
DTL buffer properly.
Fixes: 7c105b63bd ("powerpc: Add CONFIG_CPU_LITTLE_ENDIAN kernel config option.")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit db787af1b8 upstream.
When CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not set, we register the DTL
buffer for a cpu when the associated file under powerpc/dtl in debugfs
is opened. When doing so, we need to set the size of the buffer being
registered in the second u32 word of the buffer. This needs to be in big
endian, but we are not doing the conversion resulting in the below error
showing up in dmesg:
dtl_start: DTL registration for cpu 0 (hw 0) failed with -4
Fix this in the obvious manner.
Fixes: 7c105b63bd ("powerpc: Add CONFIG_CPU_LITTLE_ENDIAN kernel config option.")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 625ef8a3ac upstream.
Variable retries is not initialized in ext4_da_write_inline_data_begin()
which can lead to nondeterministic number of retries in case we hit
ENOSPC. Initialize retries to zero as we do everywhere else.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Fixes: bc0ca9df3b ("ext4: retry allocation when inline->extent conversion failed")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fc62c3b197 upstream.
We don't need to call process_ib_ipinfo() if message->kvp_hdr.operation is
KVP_OP_GET_IP_INFO in kvp_send_key(), because here we just need to pass on
the op code from the host to the userspace; when the userspace returns
the info requested by the host, we pass the info on to the host in
kvp_respond_to_host() -> process_ob_ipinfo(). BTW, the current buggy code
actually doesn't cause any harm, because only message->kvp_hdr.operation
is used by the userspace, in the case of KVP_OP_GET_IP_INFO.
The patch also adds a missing "break;" in kvp_send_key(). BTW, the current
buggy code actually doesn't cause any harm, because in the case of
KVP_OP_SET, the unexpected fall-through corrupts
message->body.kvp_set.data.key_size, but that is not really used: see
the definition of struct hv_kvp_exchg_msg_value.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 11924ba5e6 upstream.
When adding a VMCI resource, the check for an existing entry
would ignore that the new entry could be a wildcard. This could
result in multiple resource entries that would match a given
handle. One disastrous outcome of this is that the
refcounting used to ensure that delayed callbacks for VMCI
datagrams have run before the datagram is destroyed can be
wrong, since the refcount could be increased on the duplicate
entry. This in turn leads to a use after free bug. This issue
was discovered by Hangbin Liu using KASAN and syzkaller.
Fixes: bc63dedb7d ("VMCI: resource object implementation")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: Drop the version change.]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 18aded1749 upstream.
The code EXT4_IOC_SWAP_BOOT ioctl hasn't been updated in a while, and
it's a bit broken with respect to more modern ext4 kernels, especially
metadata checksums.
Other problems fixed with this commit:
* Don't allow installing a DAX, swap file, or an encrypted file as a
boot loader.
* Respect the immutable and append-only flags.
* Wait until any DIO operations are finished *before* calling
truncate_inode_pages().
* Don't swap inode->i_flags, since these flags have nothing to do with
the inode blocks --- and it will give the IMA/audit code heartburn
when the inode is evicted.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: syzbot+e81ccd4744c6c4f71354@syzkaller.appspotmail.com
[bwh: Backported to 3.16:
- Drop IS_ENCRYPTED() check
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4ab2b48c98 upstream.
The allocation with fsl_alloc_request() and kmalloc() were unchecked
fixed this up with a NULL check and appropriate cleanup.
Additionally udc->ep_qh_size was reset to 0 on failure of allocation.
Similar udc->phy_mode is initially 0 (as udc_controller was
allocated with kzalloc in fsl_udc_probe()) so reset it to 0 as well
so that this function is side-effect free on failure. Not clear if
this is necessary or sensible as fsl_udc_release() probably can not
be called if fsl_udc_probe() failed - but it should not hurt.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: b504882da5 ("USB: add Freescale high-speed USB SOC device controller driver")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.16: adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 23c7b54ca1 upstream.
When the devfreq driver and the governor driver are built as modules,
the call to devfreq_add_device() or governor_store() fails because the
governor driver is not loaded at the time the devfreq driver loads. The
devfreq driver has a build dependency on the governor but also should
have a runtime dependency. We need to make sure that the governor driver
is loaded before the devfreq driver.
This patch fixes this bug by adding a try_then_request_governor()
function. First tries to find the governor, and then, if it is not found,
it requests the module and tries again.
Fixes: 1b5c1be2c8 (PM / devfreq: map devfreq drivers to governor using name)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
[bwh: Backported to 3.16:
- Use string literal instead of DEVFREQ_GOV_SIMPLE_ONDEMAND
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 95691e3edd upstream.
Currently, "disable_clkrun" yenta_socket module parameter is only
implemented for TI CardBus bridges.
Add also an implementation for Ricoh bridges that have the necessary
setting documented in publicly available datasheets.
Tested on a RL5C476II with a Sunrich C-160 CardBus NIC that doesn't work
correctly unless the CLKRUN protocol is disabled.
Let's also make it clear in its description that the "disable_clkrun"
module parameter only works on these two previously mentioned brands of
CardBus bridges.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8911a43bc1 upstream.
The correct way to handle errors returned by regualtor_get() and friends is
to propagate the error since that means that an regulator was specified,
but something went wrong when requesting it.
For handling optional regulators, e.g. when the device has an internal
vref, regulator_get_optional() should be used to avoid getting the dummy
regulator that the regulator core otherwise provides.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[bwh: Backported to 3.16: Keep using ad5064_write() instead of
ad5064_set_config().]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit aea835f2dc upstream.
When channels are registered, the hardware channel number is not the
actual iio channel number.
This is because the driver is probed with a certain number of accessible
channels. Some pins are routed and some not, depending on the description of
the board in the DT.
Because of that, channels 0,1,2,3 can correspond to hardware channels
2,3,4,5 for example.
In the buffered triggered case, we need to do the translation accordingly.
Fixed the channel number to stop reading the wrong channel.
Fixes: 0e589d5fb ("ARM: AT91: IIO: Add AT91 ADC driver.")
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit bc1b453262 upstream.
When doing simple conversions, the driver did not acknowledge the DRDY irq.
If this irq status is not acked, it will be left pending, and as soon as a
trigger is enabled, the irq handler will be called, it doesn't know why
this status has occurred because no channel is pending, and then it will go
int a irq loop and board will hang.
To avoid this situation, read the LCDR after a raw conversion is done.
Fixes: 0e589d5fb ("ARM: AT91: IIO: Add AT91 ADC driver.")
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 432de7fd76 upstream.
The count of errors is picked up from bits 52:38 of the machine check
bank status register. But this is the count of *corrected* errors. If an
uncorrected error is being logged, the h/w sets this field to 0. Which
means that when edac_mc_handle_error() is called, the EDAC core will
carefully add zero to the appropriate uncorrected error counts.
Signed-off-by: Tony Luck <tony.luck@intel.com>
[ Massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180928213934.19890-1-tony.luck@intel.com
[bwh: Backported to 3.16: Drop change in skx_edac.c]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 908a572b80 upstream.
Using waitqueue_active() is racy. Make sure we issue a wake_up()
unconditionally after storing into fc->blocked. After that it's okay to
optimize with waitqueue_active() since the first wake up provides the
necessary barrier for all waiters, not the just the woken one.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 3c18ef8117 ("fuse: optimize wake_up")
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6e2d85ec05 upstream.
While consolidating the PHY reset in phy_init_hw() an unconditionaly
BMCR soft-reset I became quite trigger happy with those. This was later
on deactivated for the Generic PHY driver on the premise that a prior
software entity (e.g: bootloader) might have applied workarounds in
commit 0878fff1f4 ("net: phy: Do not perform software reset for
Generic PHY").
Since we have a hook to wire-up a soft_reset callback, just use that and
get rid of the call to genphy_soft_reset() entirely. This speeds up
initialization and link establishment for most PHYs out there that do
not require a reset.
Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c5d59528e2 upstream.
altera_hw_filt_init() which calls append_internal() assumes
that the node was successfully linked in while in fact it can
silently fail. So the call-site needs to set return to -ENOMEM
on append_internal() returning NULL and exit through the err path.
Fixes: 349bcf02e3 ("[media] Altera FPGA based CI driver module")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fbe1a850b3 upstream.
When the LRW block counter overflows, the current implementation returns
128 as the index to the precomputed multiplication table, which has 128
entries. This patch fixes it to return the correct value (127).
Fixes: 64470f1b85 ("[CRYPTO] lrw: Liskov Rivest Wagner, a tweakable narrow block cipher mode")
Reported-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8b97d73c4d upstream.
The ChipIdea IRQ is disabled before scheduling the otg work and
re-enabled on otg work completion. However if the job is already
scheduled we have to undo the effect of disable_irq int order to
balance the IRQ disable-depth value.
Fixes: be6b0c1bd0 ("usb: chipidea: using one inline function to cover queue work operations")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1bd54d851f upstream.
kgdboc_option_setup does not check input argument before passing it
to strlen. The argument would be a NULL pointer if "ekgdboc", without
its value, is set in command line and thus cause the following panic.
PANIC: early exception 0xe3 IP 10:ffffffff8fbbb620 error 0 cr2 0x0
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.18-rc8+ #1
[ 0.000000] RIP: 0010:strlen+0x0/0x20
...
[ 0.000000] Call Trace
[ 0.000000] ? kgdboc_option_setup+0x9/0xa0
[ 0.000000] ? kgdboc_early_init+0x6/0x1b
[ 0.000000] ? do_early_param+0x4d/0x82
[ 0.000000] ? parse_args+0x212/0x330
[ 0.000000] ? rdinit_setup+0x26/0x26
[ 0.000000] ? parse_early_options+0x20/0x23
[ 0.000000] ? rdinit_setup+0x26/0x26
[ 0.000000] ? parse_early_param+0x2d/0x39
[ 0.000000] ? setup_arch+0x2f7/0xbf4
[ 0.000000] ? start_kernel+0x5e/0x4c2
[ 0.000000] ? load_ucode_bsp+0x113/0x12f
[ 0.000000] ? secondary_startup_64+0xa5/0xb0
This patch adds a check to prevent the panic.
Cc: jason.wessel@windriver.com
Cc: gregkh@linuxfoundation.org
Cc: jslaby@suse.com
Signed-off-by: He Zhe <zhe.he@windriver.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 076ed3da0c upstream.
commit 40413955ee ("Cipso: cipso_v4_optptr enter infinite loop") fixed
a possible infinite loop in the IP option parsing of CIPSO. The fix
assumes that ip_options_compile filtered out all zero length options and
that no other one-byte options beside IPOPT_END and IPOPT_NOOP exist.
While this assumption currently holds true, add explicit checks for zero
length and invalid length options to be safe for the future. Even though
ip_options_compile should have validated the options, the introduction of
new one-byte options can still confuse this code without the additional
checks.
Signed-off-by: Stefan Nuernberger <snu@amazon.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Simon Veith <sveith@amazon.de>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 40413955ee upstream.
in for(),if((optlen > 0) && (optptr[1] == 0)), enter infinite loop.
Test: receive a packet which the ip length > 20 and the first byte of ip option is 0, produce this issue
Signed-off-by: yujuan.qi <yujuan.qi@mediatek.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 04f81f0154 upstream.
Using the IPCB() macro to get the IPv4 options is convenient, but
unfortunately NetLabel often needs to examine the CIPSO option outside
of the scope of the IP layer in the stack. While historically IPCB()
worked above the IP layer, due to the inclusion of the inet_skb_param
struct at the head of the {tcp,udp}_skb_cb structs, recent commit
971f10ec ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
reordered the tcp_skb_cb struct and invalidated this IPCB() trick.
This patch fixes the problem by creating a new function,
cipso_v4_optptr(), which locates the CIPSO option inside the IP header
without calling IPCB(). Unfortunately, this isn't as fast as a simple
lookup so some additional tweaks were made to limit the use of this
new function.
Reported-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Tested-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit aeae4f3e5c upstream.
Upon removal of the last device on a bus, the link_state of the bridge
leading to that bus is sought to be torn down by having pci_stop_dev()
call pcie_aspm_exit_link_state().
When ASPM was originally introduced by commit 7d715a6c1a ("PCI: add
PCI Express ASPM support"), it determined whether the device being
removed is the last one by calling list_empty() on the bridge's
subordinate devices list. That didn't work because the device is only
removed from the list slightly later in pci_destroy_dev().
Commit 3419c75e15 ("PCI: properly clean up ASPM link state on device
remove") attempted to fix it by calling list_is_last(), but that's not
correct either because it checks whether the device is at the *end* of
the list, not whether it's the last one *left* in the list. If the user
removes the device which happens to be at the end of the list via sysfs
but other devices are preceding the device in the list, the link_state
is torn down prematurely.
The real fix is to move the invocation of pcie_aspm_exit_link_state() to
pci_destroy_dev() and reinstate the call to list_empty(). Remove a
duplicate check for dev->bus->self because pcie_aspm_exit_link_state()
already contains an identical check.
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shaohua Li <shaohua.li@intel.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit bd24db0410 upstream.
The driver ignored the width alignment which exists due to the UYVY
colorspace format. Fix the width alignment and make use of the the
provided v4l2 helper function to set the width, height and all
alignments in one.
Fixes: 963ddc63e2 ("[media] media: tvp5150: Add cropping support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit afeaade90d upstream.
The v4l2-compliance tool complains if a video doesn't start
with a zero sequence number.
While this shouldn't cause any real problem for apps, let's
make it happier, in order to better check the v4l2-compliance
differences before and after patchsets.
This is actually an old issue. It is there since at least its
videobuf2 conversion, e. g. changeset 3829fadc461 ("[media]
em28xx: convert to videobuf2"), if VB1 wouldn't suffer from
the same issue.
Fixes: d3829fadc4 ("[media] em28xx: convert to videobuf2")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 15644bfa19 upstream.
Instead of using a register value, use an AMUX name, as otherwise
VIDIOC_G_AUDIO would fail.
Fixes: 766ed64de5 ("V4L/DVB (11827): Add support for Terratec Grabster AV350")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f823ce2a12 upstream.
Follow the V4L2 spec, as warned by v4l2-compliance:
warn: v4l2-test-formats.cpp(732): TRY_FMT cannot handle an invalid pixelformat.
warn: v4l2-test-formats.cpp(733): This may or may not be a problem. For more information see:
warn: v4l2-test-formats.cpp(734): http://www.mail-archive.com/linux-media@vger.kernel.org/msg56550.html
Fixes: bddcf63313 ("V4L/DVB (9927): em28xx: use a more standard way to specify video formats")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4d19db777a upstream.
Calling napi_schedule() from process context does not ensure that the
NET_RX softirq is run in a timely fashion. So trigger it manually.
This is no big issue with current code. A call to ndo_open() is usually
followed by a ndo_set_rx_mode() call, and for qeth this contains a
spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out
early.
Nevertheless it's best to not depend on this behaviour, and just fix
the issue at its source like all other drivers do. For instance see
commit 83a0c6e589 ("i40e: Invoke softirqs after napi_reschedule").
Fixes: a1c3ed4c9c ("qeth: NAPI support for l2 and l3 discipline")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit cb90a2c6f7 upstream.
Since the max8998 MFD driver supports instantiation by DT, platform data
retrieval is handled in MFD probe and cell drivers should get use
the pdata field of max8998_dev struct to obtain them.
Fixes: ee999fb3f1 ("mfd: max8998: Add support for Device Tree")
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
[bwh: Backported to 3.16: adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0ab93e9c99 upstream.
The genweq_add_file and genwqe_del_file by caching current without
using reference counting embed the assumption that a file descriptor
will never be passed from one process to another. It even embeds the
assumption that the the thread that opened the file will be in
existence when the process terminates. Neither of which are
guaranteed to be true.
Therefore replace caching the task_struct of the opener with
pid of the openers thread group id. All the knowledge of the
opener is used for is as the target of SIGKILL and a SIGKILL
will kill the entire process group.
Rename genwqe_force_sig to genwqe_terminate, remove it's unncessary
signal argument, update it's ownly caller, and use kill_pid
instead of force_sig.
The work force_sig does in changing signal handling state is not
relevant to SIGKILL sent as SEND_SIG_PRIV. The exact same processess
will be killed just with less work, and less confusion. The work done
by force_sig is really only needed for handling syncrhonous
exceptions.
It will still be possible to cause genwqe_device_remove to wait
8 seconds by passing a file descriptor to another process but
the possible user after free is fixed.
Fixes: eaf4722d46 ("GenWQE Character device and DDCB queue")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Frank Haverkamp <haver@linux.vnet.ibm.com>
Cc: Joerg-Stephan Vogt <jsvogt@de.ibm.com>
Cc: Michael Jung <mijung@gmx.net>
Cc: Michael Ruettger <michael@ibmra.de>
Cc: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Eberhard S. Amann <esa@linux.vnet.ibm.com>
Cc: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1e4ac5d6fe upstream.
If chip unable to fully initialize, use full shutdown sequence to clear out
any stale FW state.
Fixes: e315cd28b9 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring")
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3597dfe01d upstream.
Instead of playing whack-a-mole and changing SEND_SIG_PRIV to
SEND_SIG_FORCED throughout the kernel to ensure a pid namespace init
gets signals sent by the kernel, stop allowing a pid namespace init to
ignore SIGKILL or SIGSTOP sent by the kernel. A pid namespace init is
only supposed to be able to ignore signals sent from itself and
children with SIG_DFL.
Fixes: 921cf9f630 ("signals: protect cinit from unblocked SIG_DFL signals")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
