Introduce 2 types of GTK, Tx (for this STA) and Rx (for each peer).
Now, AP has only Tx GTK, STA - only Rx one. PBSS not supported yet;
for it, continue using pseudo-DMS.
Handle per-vring .1x state, update it from WMI_VRING_EN_EVENTID
event. This allows unification for unicast and broadcast vrings.
This mechanism replaces former per-CID "data_port_open"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pmc is a hardware debug mechanism which allows capturing phy data,
packets, and internally generated events and messages synchronized
and time stamped by the hardware. It requires memory buffers
allocated by the driver in order to be used by hardware dma to
upstream real time debug data to host memory.
Driver will handle memory allocation and release, and fetching
the data from the memory to application layer via debug file
system. The configuration of pmc is handled entirely by the
application layer.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Parameters for the start_ap and change_bcon contains
probe response template and probe response IE's.
supplicant puts in the proberesp_ies only WPS related IE's,
while firmware need all IE's, most notable is RSN that is not
included in the proberesp_ies.
Always use IE's provided by the bcon->probe_resp
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Boot loader "ready" indication has changed from "bit0 set"
to "only bit0 set". This is to address hardware glitches.
Due to glitches, sometimes right after reset register reads
0xffffffff, or (rarely) other garbage.
Reflect this in the driver
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx descriptor fields accordingly to the updated
hardware documentation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes it takes for the firmware more than 20ms to
react on "echo" command after reset. Increase timeout
from 20 to 50ms
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
qca6174 otp binary seems to always return an error to the host, even if the
calibration succeeded. Add a firmware feature flag to detect if the firmware
image which have this problem and workaround the issue in ath10k by ignoring
the error code.
I was also considering making this hw specific flag but as this is strictly a
firmware issue it's best to handle this via a firmware feature flag so that it
will be easy to disable the workaround.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level() and all
remaining access to codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The L3 Error handling on OMAP5 for the most part is very similar
to that of OMAP4, and had leveraged common data structures and
register layout definitions so far. Upon closer inspection, there
are a few minor differences causing an incorrect decoding and
reporting of the master NIU upon an error:
1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies
11 bits on OMAP5 as against 8 bits on OMAP4, with the master
NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR
field.
2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3
input sources on OMAP5. The common DEBUGSS source is at a
different input on each SoC.
Fix the above issues by using a OMAP5-specific compatible property
and using SoC-specific data where there are differences.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The base address for DRA7 CLK1_HOST_CLK1_2 host instance is
0x44800000, so correct offset is 0x800000. DRA7 TRM rev X(fewb 2015)
has updates for this information.
With wrong offset these errors are not correctly cleared by the L3
IRQ handler and cause an continuous interrupt scenario and system lockup.
Signed-off-by: Illia Smyrnov <illia.smyrnov@globallogic.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rt5650 and rt5645 are similar codec so reuse the cht_bsw_rt5645 driver
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The queued TRIM problems appear to be generic to Samsung's firmware and
not tied to a particular model. A recent update to the 840 EVO firmware
introduced the same issue as we saw on 850 Pro.
Blacklist queued TRIM on all 800-series drives while we work this issue
with Samsung.
Reported-by: Günter Waller <g.wal@web.de>
Reported-by: Sven Köhler <sven.koehler@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Fix a typo in DRA7 dtsi where 12 bytes are needed for register
description of ABB efuse registers, however only 8 bytes are provided
to map. For some weird reason, this does not generate abort at offset
0x8, probably due to default maps already provided in io.c for the bus
register ranges.
Reported-by: Matt Gessner <Matt.Gessner@windriver.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching the GPIO fan
gpio over from 1 to 2 to allow for a potential fix at a later point in
time for USB client VBUS detection using PMIC VBUS detect capability.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching over to UART
pins that now allow for UART download capability. All original boards
should either have been returned for modifications or already modified
for the required change and maintaining compatibility for older boards
are no longer needed.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new AM437x SK Beta boards have removed the
large capacitors on the gpio-matrix column lines
which means we can reduce col-scan-delay-us to 5us
without loosing functionality.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x Starter Kit uses a NewHaven Display module with
a 4.3" display and EDT FT5306 touchscreen
On that module's new revision, NewHave decided to change
the pinout on the 6 pin flat-pcb touchscreen connector so
that instead of having WAKE pin, we now have RESETn.
The new display module is available on AM437x SK Beta and
all new revisions while the older revision is only available
on AM437x SK Alpha which, unfortunately, can't be supported
anymore in mainline without a revert of this patch.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With commit bc078316d8 ("ARM: dts: DRA7: Add node for RTC"), we now
have AM57xx RTC register itself as alias 0 even before DS1307 or TPS
rtc drivers are loaded up. However, since neither TPS, nor AM57xx RTC
are capable of being backedup by battery, we would like to maintain
the "primary" rtc as mcp79410 rtc device.
This also generates the following warnings in the bootlog highlighting
the issue:
[ 5.895445] rtc-ds1307 2-006f: /aliases ID 0 not available
...
[ 6.476285] palmas-rtc 48070000.i2c:tps659038@58:tps659038_rtc: /aliases ID 1 not available
So, add proper aliases to ensure that RTC order is always consistent
to userspace immaterial of probe order.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The interrupt polarity provided in devicetree is used to configure
the interrupt controller(ARM GIC), however, it seems that we have an
inverter at the GIC boundary inside AM57xx which inverts the signal
input from sys_irq external interrupt source.
Further, as per GIC distributor TRM,
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438d/BGBHIACJ.html#BABJFCFB
ARM GIC distributor does not support IRQ trigger type
IRQ_TYPE_LEVEL_LOW, and only rising or level high signals.
However, for some reason, the current configuration(which gets ignored
by GIC driver) functions on some platforms, however, on few platforms
results in infinite interrupts hogging the system down.
Switch over to rising edge for GIC configuration which is also aligned
with trigger point from the RTC chip and the internal inversion.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing #iommu-cells property to the isp and iva iommu nodes. This
fixes the binding (property is required according to the generic iommu
binding) and removes the following kernel warning triggered once the
iommu nodes are referenced:
[ 0.647521] /ocp/isp@480bc000: could not get #iommu-cells for /ocp/mmu@480bd400
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to enable EXTCON_USB_GPIO_USB and not
EXTCON_GPIO_USB.
Fixes: c08a54c0eb ("ARM: omap2plus_defconfig: Enable EXTCON_GPIO_USB")
Reported-by: Nishant Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by-by: Nishanth Menon <nm@ti.com
Tested-by: Nishanth Menon <nm@ti.com
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
N900 audio recording needs that codec provides bias voltage for integrated
digital microphone and headset microphone depending which one is used.
Digital microphone uses 2 V bias and it comes from the codec A part. Codec
B part drives the headset microphone bias and that is set to 2.5 V.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[Jarkko: Headset mic bias changed to 2 (2.5 V) as it was before commit
e2e8bfdf61 ("ASoC: tlv320aic3x: Convert mic bias to a supply widget")]
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The 'overloads-avoided' counter itself was removed several years ago by
commit 78c210e (Revert "knfsd: avoid overloading the CPU scheduler with
enormous load averages").
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
With sessions in v4.1 or later we don't need to manually probe the backchannel
connection, so we can declare it up instantly after setting up the RPC client.
Note that we really should split nfsd4_run_cb_work in the long run, this is
just the least intrusive fix for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Checking the rpc_client pointer is not a reliable way to detect
backchannel changes: cl_cb_client is changed only after shutting down
the rpc client, so the condition cl_cb_client = tk_client will always be
true.
Check the RPC_TASK_KILLED flag instead, and rewrite the code to avoid
the buggy cl_callbacks list and fix the lifetime rules due to double
calls of the ->prepare callback operations method for this retry case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
We must only increment the sequence id if the client has seen and responded
to a request. If we failed to deliver it to the client we must resend with
the same sequence id. So just like the client track errors at the transport
level differently from those returned in the XDR.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
In an environment where the KDC is running Active Directory, the
exported composite name field returned in the context could be large
enough to span a page boundary. Attaching a scratch buffer to the
decoding xdr_stream helps deal with those cases.
The case where we saw this was actually due to behavior that's been
fixed in newer gss-proxy versions, but we're fixing it here too.
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Simo Sorce <simo@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
For the sake of forgetful clients, the server should return the layouts
to the file system on 'last close' of a file (assuming that there are no
delegations outstanding to that particular client) or on delegreturn
(assuming that there are no opens on a file from that particular
client).
In theory the information is all there in current data structures, but
it's not efficiently available; nfs4_file->fi_ref includes references on
the file across all clients, but we need a per-(client, file) count.
Walking through lots of stateid's to calculate this on each close or
delegreturn would be painful.
This patch introduces infrastructure to maintain per-client opens and
delegation counters on a per-file basis.
[hch: ported to the mainline pNFS support, merged various fixes from Jeff]
Signed-off-by: Sachin Bhamare <sachin.bhamare@primarydata.com>
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
If we find a non-confirmed openowner we jump to exit the function, but do
not set an error value. Fix this by factoring out a helper to do the
check and properly set the error from nfsd4_validate_stateid.
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Commit df52699e4f ("NFSv4.1: Don't cache deviceids that have no
notifications") causes the Linux NFS client to stop caching deviceid's
unless a server pretends to support deviceid notifications. While this
behavior is stupid and the language around this area in rfc5661 is a
mess carified by an errata that I submittted, Trond insists on this
behavior. Not caching deviceids degrades block layout performance
massively as a GETDEVICEINFO is fairly expensive.
So add this hack to make the Linux client happy again.
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
If we use a combination of VMODE and I2C4 for retention modes,
eventually the off idle power consumption will creep up by about
23mW, even during off mode with I2C4 always staying enabled.
Turns out this is because of erratum i531 "Extra Power Consumed
When Repeated Start Operation Mode Is Enabled on I2C Interface
Dedicated for Smart Reflex (I2C4)" as pointed out by Nishanth
Menon <nm@ti.com>.
Let's fix the issue by adding i2c_cfg_clear_mask for the bits
to clear when initializing the I2C4 adapter so we can clear
SREN bit that drives the I2C4 lines low otherwise when there
is no traffic.
Fixes: 3b8c4ebb76 ("ARM: OMAP3: Fix idle mode signaling for
Cc: stable@vger.kernel.org # v3.16+
sys_clkreq and sys_off_mode")
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It is 'perf kmem' support caller statistics for page. Unlike slab case,
the tracepoints in page allocator don't provide callsite info. So it
records with callchain and extracts callsite info.
Note that the callchain contains several memory allocation functions
which has no meaning for users. So skip those functions to get proper
callsites. I used following regex pattern to skip the allocator
functions:
^_?_?(alloc|get_free|get_zeroed)_pages?
This gave me a following list of functions:
# perf kmem record --page sleep 3
# perf kmem stat --page -v
...
alloc func: __get_free_pages
alloc func: get_zeroed_page
alloc func: alloc_pages_exact
alloc func: __alloc_pages_direct_compact
alloc func: __alloc_pages_nodemask
alloc func: alloc_page_interleave
alloc func: alloc_pages_current
alloc func: alloc_pages_vma
alloc func: alloc_page_buffers
alloc func: alloc_pages_exact_nid
...
The output looks mostly same as --alloc (I also added callsite column
to that) but groups entries by callsite. Currently, the order,
migrate type and GFP flag info is for the last allocation and not
guaranteed to be same for all allocations from the callsite.
---------------------------------------------------------------------------------------------
Total_alloc (KB) | Hits | Order | Mig.type | GFP flags | Callsite
---------------------------------------------------------------------------------------------
1,064 | 266 | 0 | UNMOVABL | 000000d0 | __pollwait
52 | 13 | 0 | UNMOVABL | 002084d0 | pte_alloc_one
44 | 11 | 0 | MOVABLE | 000280da | handle_mm_fault
20 | 5 | 0 | MOVABLE | 000200da | do_cow_fault
20 | 5 | 0 | MOVABLE | 000200da | do_wp_page
16 | 4 | 0 | UNMOVABL | 000084d0 | __pmd_alloc
16 | 4 | 0 | UNMOVABL | 00000200 | __tlb_remove_page
12 | 3 | 0 | UNMOVABL | 000084d0 | __pud_alloc
8 | 2 | 0 | UNMOVABL | 00000010 | bio_copy_user_iov
4 | 1 | 0 | UNMOVABL | 000200d2 | pipe_write
4 | 1 | 0 | MOVABLE | 000280da | do_wp_page
4 | 1 | 0 | UNMOVABL | 002084d0 | pgd_alloc
---------------------------------------------------------------------------------------------
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Pekka Enberg <penberg@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/1429592107-1807-2-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Accept multiple filter options. Each filters are combined by logical-or.
E.g. --filter abc* --filter *def is same as --filter abc*|*def
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150424094748.23967.63355.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add strfilter__string to recover rules string from strfilter. This will
be good for debugging.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150424094746.23967.52434.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently, perf probe considers patterns including a '.' to be a file.
However, this causes problems on powerpc ABIv1 where all functions have
a leading '.':
$ perf probe -F | grep schedule_timeout_interruptible
.schedule_timeout_interruptible
$ perf probe .schedule_timeout_interruptible
Semantic error :File always requires line number or lazy pattern.
Error: Command Parse Error.
Fix this:
- by checking the probe pattern in more detail, and
- skipping leading dot if one exists when creating/deleting events.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/db680f7cb11c4452b632f908e67151f3aa0f4602.1430217967.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
