Commit bca9690b94 ("clk: divider: Make generic for usage elsewhere")
returned only the divider value for read-only dividers instead of the
actual rate.
Fixes: bca9690b94 ("clk: divider: Make generic for usage elsewhere")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Tested-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.
[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to AM437x TRM, Document SPRUHL7B, Revised December 2014,
Section 7.2.1 Pad Control Registers, setting bit 19 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness.
Current users of the macro (i2c, mdio, and uart) are left unmodified as
SLEWCTRL_FAST was the macro used and actual desired state. Tested on
am437x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to AM335x TRM, Document spruh73l, Revised February 2015,
Section 9.2.2 Pad Control Registers, setting bit 6 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness.
Current users of the macro (i2c and mdio) are left unmodified as
SLEWCTRL_FAST was the macro used and actual desired state. Tested on
am335x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.
Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);
[ 1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use external clock for RMII since the internal clock doesn't meet the
jitter requirements.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 4da1c67719 ("add tbclk data for ehrpwm")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 9e100ebafb: ("Fix ehrpwm tbclk data")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can simplify the code by returning patch_build_controls() directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes 85dc74e9 (ARM: dts: omap5 clock data)
On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch to add an VT1613 AC97 codec support.
This codec has additional DC offset removal control,
headphone output and no video input.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU960DAAoJECTWi3JdVIfQkKIH/RDvxRn8dvKOPF5U9Uix3chH
JWKkzqfsMP0EpmQTzCQPp0ShAyYcWSbYsopicynPxUem5vS4Z8+UmOgEEgkj59pK
USbF6v1jCQXA6BcbKyUcRRBD9FtRkfVDc7mYbRs2CcwQz2CGCgee41cvPM+2BT+z
QdNC9UJARSweGvE1IUJSfpfYOly+BJ2s0/28RaQ0PGt+I0auoYx7IMFgMSDjv2p6
PY0kyQiwm3Kyj2uNXPZ5gEuPxlw/t8n4fbQNrBYAvxzN+EF5NrGdKE3N7MI1xRV/
EkFhzy+uM3X9c37tb2lT2fgPFlBc9rgPuLPSyoQ6nxa5ghCqAlgRhzpxRem8hhU=
=VlCw
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Changes for v4.1
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
A few driver specific fixes here, none of them earth shattering in
themselves, that have accumliated since the opening of the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU96stAAoJECTWi3JdVIfQLfUH/jBYQqxrPp8qm7Lt9LOuwC4U
SOi0ERIVhLSKZMo7G4wHmbEapx2FBgH+wxqh9kNLaISvOIH4odFS4Fr1XYE70cY9
97M46uzLqdaKCDgvkXdx1NLA0zubEGWLOtdVYlrMAzin0FXNH+KYhxkRQbJ6f0LE
yKmNemnHHtJ4gDl/kMED7bc+mkYSOpwUE/8HLOEA8bcE3luDnj7rvQwOhPIYq0Tz
Ij4GM8HSfWPp/k3YmZVcF8GA6icN3LG5Jg7DOu6S19fMYimTDaHQDCw0AoLfiIOQ
DykyHg7ay/I3B6zUz4JikLIW5KjFxZfeQ818YE0GQ4PgePfb0GSIFt0LnNmq4Oo=
=GIb7
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.0
A few driver specific fixes here, none of them earth shattering in
themselves, that have accumliated since the opening of the merge window.
Using the pvops kernel a NULL pointer dereference was detected on a
large machine (144 processors) when booting as dom0 in
evtchn_fifo_unmask() during assignment of a pirq.
The event channel in question was the first to need a new entry in
event_array[] in events_fifo.c. Unfortunately xen_irq_info_pirq_setup()
is called with evtchn being 0 for a new pirq and the real event channel
number is assigned to the pirq only during __startup_pirq().
It is mandatory to call xen_evtchn_port_setup() after assigning the
event channel number to the pirq to make sure all memory needed for the
event channel is allocated.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
MediaTek SoC expect to work with a pinctrl driver.
Select PINCTRL if ARCH_MEDIATEK is selected.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We finally have all the pieces in place, so let's include the
vector facility bit in the mask of available hardware facilities
for the guest to recognize. Also, enable the vector functionality
in the guest control blocks, to avoid a possible vector data
exception that would otherwise occur when a vector instruction
is issued by the guest operating system.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Store additional status in the machine check handler, in order to
collect status (such as vector registers) that is not defined by
store status.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The new SIGP order Store Additional Status at Address is totally
handled by user space, but we should still record the occurrence
of this order in the kernel code.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
A new exception type for vector instructions is introduced with
the new processor, but is handled exactly like a Data Exception
which is already handled by the system.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Define and allocate space for both the host and guest views of
the vector registers for a given vcpu. The 32 vector registers
occupy 128 bits each (512 bytes total), but architecturally are
paired with 512 additional bytes of reserved space for future
expansion.
The kvm_sync_regs structs containing the registers are union'ed
with 1024 bytes of padding in the common kvm_run struct. The
addition of 1024 bytes of new register information clearly exceeds
the existing union, so an expansion of that padding is required.
When changing environments, we need to appropriately save and
restore the vector registers viewed by both the host and guest,
into and out of the sync_regs space.
The floating point registers overlay the upper half of vector
registers 0-15, so there's a bit of data duplication here that
needs to be carefully avoided.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The guest debug functions work on absolute addresses and should use the
read_guest_abs() function rather than general read_guest() that
works with logical addresses.
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Alexander Yarygin <yarygin@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
trace-cmd fails to parse the instruction interception trace point:
"Error: expected type 5 but read 4
failed to read event print fmt for kvm_s390_intercept_instruction"
The result is an unformatted string in the output, with a warning:
"kvm_s390_intercept_instruction: [FAILED TO PARSE]..."
So let's add parentheses around the instruction parser macro to fix the format
parsing.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The function kvm_s390_vcpu_setup_model() now performs all cpu model realated
setup tasks for a vcpu. Besides cpuid and ibc initialization, facility list
assignment takes place during the setup step as well. The model setup has been
pulled to the begin of vcpu setup to allow kvm facility tests.
There is no need to protect the cpu model setup with a lock since the attributes
can't be changed anymore as soon the first vcpu is online.
Signed-off-by: Michael Mueller <mimu@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The common s390 function insn_length() results in slightly smaller
(and thus hopefully faster) code than the calculation of the
instruction length via a lookup-table. So let's use that function
in the interrupt delivery code, too.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
When the SIE exited by a DAT access exceptions which we can not
resolve, the guest tried to access a page which is out of bounds
and can not be paged-in. In this case we have to signal the bad
access by injecting an address exception. However, address exceptions
are either suppressing or terminating, i.e. the PSW has to point to
the next instruction when the exception is delivered. Since the
originating DAT access exception is nullifying, the PSW still
points to the offending instruction instead, so we've got to forward
the PSW to the next instruction.
Having fixed this issue, we can now also enable the TPROT
interpretation facility again which had been disabled because
of this problem.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
When certain program exceptions (e.g. DAT access exceptions) occur,
the current instruction has to be nullified, i.e. the old PSW that
gets written into the low-core has to point to the beginning of the
instruction again, and not to the beginning of the next instruction.
Thus we have to rewind the PSW before writing it into the low-core.
The list of nullifying exceptions can be found in the POP, chapter 6,
figure 6-1 ("Interruption Action").
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The reinjection of an I/O interrupt can fail if the list is at the limit
and between the dequeue and the reinjection, another I/O interrupt is
injected (e.g. if user space floods kvm with I/O interrupts).
This patch avoids this memory leak and returns -EFAULT in this special
case. This error is not recoverable, so let's fail hard. This can later
be avoided by not dequeuing the interrupt but working directly on the
locked list.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
If the I/O interrupt could not be written to the guest provided
area (e.g. access exception), a program exception was injected into the
guest but "inti" wasn't freed, therefore resulting in a memory leak.
In addition, the I/O interrupt wasn't reinjected. Therefore the dequeued
interrupt is lost.
This patch fixes the problem while cleaning up the function and making the
cc and rc logic easier to handle.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
s390 documentation requires words 0 and 10-15 to be reserved and stored as
zeros. As we fill out all other fields, we can memset the full structure.
Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
There is a missing lower bound check on "pitchbend" so it means we can
read up to 6 elements before the start of the opl3_note_table[] array.
Thanks to Clemens Ladisch for his help with this patch.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_DEBUG_SET_MODULE_RONX is enabled, the sizes of
module sections are aligned up so appropriate permissions can
be applied. Adjusting for the symbol table may cause them to
become unaligned. Make sure to re-align the sizes afterward.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The set_memory_* functions currently only support module
addresses. The addresses are validated using is_module_addr.
That function is special though and relies on internal state
in the module subsystem to work properly. At the time of
module initialization and calling set_memory_*, it's too early
for is_module_addr to work properly so it always returns
false. Rather than be subject to the whims of the module state,
just bounds check against the module virtual address range.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This adds a driver for random number generator present on Broadcom
IPROC devices.
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Documents the IPROC random number generator device tree bindings
used in some Broadcom chipsets.
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 7e933d3b1e ("crypto: ux500: use dmaengine_prep_slave_sg
API") changed the code to use the new API, but forgot to update an error
message.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is properly defined in the md5 header file.
Signed-off-by: Martin Hicks <mort@bork.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There were multiple loops in a row, for each separate step of the
initialization of the channels. Simplify to a single loop.
Signed-off-by: Martin Hicks <mort@bork.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The BIOS might reconfigure pins as it needs when S3 is entered. This might
cause drivers using the GPIOs to fail because the state was wrong or
interrupts stopped working.
Fix this by saving and restoring enough pin context over system sleep.
Reported-by: Hans Holmberg <hans.holmberg@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When DMA descriptor allocation fails we should not try to assign any fields in
the bad descriptor. The patch adds the necessary checks for that.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Instead of handling everything in the driver's first level interrupt
handler, we can take advantage of already existing flow handlers that are
provided by the IRQ core.
This changes the functionality a bit also. Previously the driver looped
over pending interrupts in a single loop, restarting the loop if some
interrupt changed state. This caused problem with Lenovo Thinkpad 10
digitizer that it was not able to deassert the interrupt before the driver
disabled the interrupt for good (looplimit was exhausted).
Rework the interrupt handling logic a bit so that we provide proper mask,
ack and unmask operations in terms of Baytrail GPIO hardware and loop over
pending interrupts only once. If the interrupt remains asserted the first
level handler will be re-triggered automatically.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the pin is already configured as GPIO and it has any of the triggering
flags set, we may get spurious interrupts depending on the state of the
pin.
Prevent this by clearing the triggering flags on such pins. However, if the
pin is also configured as "direct IRQ" we leave the flags as is. Otherwise
it will prevent interrupts that are routed directly to IO-APIC.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
