Zotac ZBOX PI320, a Baytrail based mini-PC, has power button connected to a
GPIO pin and it is exposed to the operating system as Windows 8 button
array. This is implemented in Linux as a driver using gpio_keys.
However, BIOS on this particula machine forgot to mux the pin to be a GPIO
instead of native function, which results following message to be seen on
the console:
byt_gpio INT33FC:02: pin 16 cannot be used as GPIO.
This causes power button to not work as the driver was not able to request
the GPIO it needs.
So instead of completely preventing this we allow turning the pin as GPIO
but issue warning that something might be wrong.
Reported-by: Benjamin Adler <benadler@gmx.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPMC_CONFIG1_i parameters CLKACTIVATIONTIME and WAITMONITORINGTIME
have reserved values.
Raise an error if calculated timings try to program reserved values.
GPMC_CONFIG1_i ATTACHEDDEVICEPAGELENGTH and DEVICESIZE were already checked
when parsing the DT.
Explicitly comment invalid values on gpmc_cs_show_timings for
-CLKACTIVATIONTIME
-WAITMONITORINGTIME
-DEVICESIZE
-ATTACHEDDEVICEPAGELENGTH
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
There is a race condition between e1000_change_mtu's cleanups and
netpoll, when we change the MTU across jumbo size:
Changing MTU frees all the rx buffers:
e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings ->
e1000_clean_rx_ring
Then, close to the end of e1000_change_mtu:
pr_info -> ... -> netpoll_poll_dev -> e1000_clean ->
e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag
And when we come back to do the rest of the MTU change:
e1000_up -> e1000_configure -> e1000_configure_rx ->
e1000_alloc_jumbo_rx_buffers
alloc_jumbo finds the buffers already != NULL, since data (shared with
page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage,
or at least not what is expected when in jumbo state.
This results in an unusable adapter (packets don't get through), and a
NULL pointer dereference on the next call to e1000_clean_rx_ring
(other mtu change, link down, shutdown):
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330
[...]
Call Trace:
[<ffffffff81195445>] put_page+0x55/0x60
[<ffffffff815d9f44>] e1000_clean_rx_ring+0x134/0x200
[<ffffffff815da055>] e1000_clean_all_rx_rings+0x45/0x60
[<ffffffff815df5e0>] e1000_down+0x1c0/0x1d0
[<ffffffff811e2260>] ? deactivate_slab+0x7f0/0x840
[<ffffffff815e21bc>] e1000_change_mtu+0xdc/0x170
[<ffffffff81647050>] dev_set_mtu+0xa0/0x140
[<ffffffff81664218>] do_setlink+0x218/0xac0
[<ffffffff814459e9>] ? nla_parse+0xb9/0x120
[<ffffffff816652d0>] rtnl_newlink+0x6d0/0x890
[<ffffffff8104f000>] ? kvm_clock_read+0x20/0x40
[<ffffffff810a2068>] ? sched_clock_cpu+0xa8/0x100
[<ffffffff81663802>] rtnetlink_rcv_msg+0x92/0x260
By setting the allocator to a dummy version, netpoll can't mess up our
rx buffers. The allocator is set back to a sane value in
e1000_configure_rx.
Fixes: edbbb3ca10 ("e1000: implement jumbo receive with partial descriptors")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.
Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.
Move netif_carrier_off as early as possible.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While addressing the pin problem I noticed that all of the pin register
values where having to be pushed onto the stack each time the function was
called. To avoid that I am making them static const so that they should
only need to be allocated once and we can avoid all the instructions to get
them onto the stack..
size before:
text data bss dec hex filename
161477 10512 8 171997 29fdd drivers/net/ethernet/intel/igb/igb.ko
size after:
text data bss dec hex filename
161205 10512 8 171725 29ecd drivers/net/ethernet/intel/igb/igb.ko
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When building the kernel using the gcc 4.8.3 compiler included in Fedora 20
I was repeatedly seeing the warning:
drivers/net/ethernet/intel/igb/igb_ptp.c: In function ‘igb_ptp_feature_enable_i210’:
drivers/net/ethernet/intel/igb/igb_ptp.c:395:21: warning: ‘pin’ may be used uninitialized in this function
[-Wmaybe-uninitialized]
tssdp &= ~ts_sdp_en[pin];
^
drivers/net/ethernet/intel/igb/igb_ptp.c:471:6: note: ‘pin’ was declared here
int pin;
^
To resolve it I am assigning the pin a value of -1 when it is instantiated.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Starting I219, the NVM will not be mapped to its own BAR, but to an
address region in another bar. The mapping/unmapping is relevant
to older HW only.
CC: John W Linville <linville@tuxdriver.com>
Reported-by: John W Linville <linville@tuxdriver.com>
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The interface to the device flash was modified in i219 and later HW.
This patch better describes the change and the impact on the driver.
CC: John W Linville <linville@tuxdriver.com>
Reported-by: John W Linville <linville@tuxdriver.com>
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The WAITMONITORINGTIME is expressed as a number of GPMC_CLK clock cycles,
even though the access is defined as asynchronous, and no GPMC_CLK clock
is provided to the external device. Still, GPMCFCLKDIVIDER is used as a divider
for the GPMC clock, so it must be programmed to define the
correct WAITMONITORINGTIME delay.
This patch correctly computes WAITMONITORINGTIME in GPMC_CLK cycles instead of GPMC_FCLK cycles,
both during programming (gpmc_cs_set_timings) and during retrieval (gpmc_cs_show_timings).
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
The WAITMONITORINGTIME is expressed as a number of GPMC_CLK clock cycles,
even though the access is defined as asynchronous, and no GPMC_CLK clock
is provided to the external device. Still, GPMCFCLKDIVIDER is used as a divider
for the GPMC clock, so it must be programmed to define the
correct WAITMONITORINGTIME delay.
Calculate GPMCFCLKDIVIDER independent of gpmc,sync-clk-ps in DT for
pure asynchronous accesses, i.e. both read and write asynchronous.
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
The WAITMONITORINGTIME is expressed as a number of GPMC_CLK clock cycles,
even though the access is defined as asynchronous, and no GPMC_CLK clock
is provided to the external device. Still, GPMCFCLKDIVIDER is used as a divider
for the GPMC clock, so it must be programmed to define the
correct WAITMONITORINGTIME delay.
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
DTS output was formatted to require additional work when copy-pasting into DTS.
Nano-second timings were replaced with interval of values that produce the same
number of clock ticks.
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Introduced by commit:
6afda7f507 ASoC: davinci-mcasp: Allow complete shutdown of McASP when not in use
I'm really sorry for this...
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
GPMC debug output is aligned to 10 characters for field names.
However, some fields have bigger names, screwing up the alignment.
Consequently, alignment was changed to longest field name (17 chars) for now.
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
This patch adds support for spawning buses as children of the GPMC.
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
OMAP2+ GPMC driver undefines DEBUG, which makes it unnecessarily
hard to turn DEBUG on. Remove the offending lines.
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Timeout was scheduled only in case CRDA was called due to user hints,
but was not scheduled for other cases. This can result in regulatory
hint processing getting stuck in case that there is no CRDA configured.
Change this by scheduling a timeout every time CRDA is called. In
addition, in restore_regulatory_settings() all pending requests are
restored (and not only the user ones).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the indoor setting configuration assumed that as
long as a station interface is connected, the indoor environment
setting does not change. However, this assumption is problematic
as:
- It is possible that a station interface is connected to a mobile
AP, e.g., softAP or a P2P GO, where it is possible that both the
station and the mobile AP move out of the indoor environment making
the indoor setting invalid. In such a case, user space has no way to
invalidate the setting.
- A station interface disconnection does not necessarily imply that
the device is no longer operating in an indoor environment, e.g.,
it is possible that the station interface is roaming but is still
stays indoor.
To handle the above, extend the indoor configuration API to allow
user space to indicate a change of indoor settings, and allow it to
indicate weather it controls the indoor setting, such that:
1. If the user space process explicitly indicates that it is going
to control the indoor setting, do not clear the indoor setting
internally, unless the socket is released. The user space process
should use the NL80211_ATTR_SOCKET_OWNER attribute in the command
to state that it is going to control the indoor setting.
2. Reset the indoor setting when restoring the regulatory settings in
case it is not owned by a user space process.
Based on the above, a user space tool that continuously monitors the
indoor settings, i.e., tracking power setting, location etc., can
indicate environment changes to the regulatory core.
It should be noted that currently user space is the only provided mechanism
used to hint to the regulatory core over the indoor/outdoor environment --
while the country IEs do have an environment setting this has been completely
ignored by the regulatory core by design for a while now since country IEs
typically can contain bogus data.
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: ArikX Nemtsov <arik@wizery.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Directly update the indoor setting without wrapping it as
a regulatory request, to simplify the processing.
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On gcc5 the kernel does not link:
ld: .eh_frame_hdr table[4] FDE at 0000000000000648 overlaps table[5] FDE at 0000000000000670.
Because prior GCC versions always emitted NOPs on ALIGN directives, but
gcc5 started omitting them.
.LSTARTFDEDLSI1 says:
/* HACK: The dwarf2 unwind routines will subtract 1 from the
return address to get an address in the middle of the
presumed call instruction. Since we didn't get here via
a call, we need to include the nop before the real start
to make up for it. */
.long .LSTART_sigreturn-1-. /* PC-relative start address */
But commit 69d0627a7f ("x86 vDSO: reorder vdso32 code") from 2.6.25
replaced .org __kernel_vsyscall+32,0x90 by ALIGN right before
__kernel_sigreturn.
Of course, ALIGN need not generate any NOP in there. Esp. gcc5 collapses
vclock_gettime.o and int80.o together with no generated NOPs as "ALIGN".
So fix this by adding to that point at least a single NOP and make the
function ALIGN possibly with more NOPs then.
Kudos for reporting and diagnosing should go to Richard.
Reported-by: Richard Biener <rguenther@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: <stable@vger.kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1425543211-12542-1-git-send-email-jslaby@suse.cz
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This has nothing to do with the init thread or the initial
anything. It's just the CPU's TSS.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/a0bd5e26b32a2e1f08ff99017d0997118fbb2485.1425611534.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The INIT_TSS is unnecessary. Just define the initial TSS where
'cpu_tss' is defined.
While we're at it, merge the 32-bit and 64-bit definitions. The
only syntactic change is that 32-bit kernels were computing sp0
as long, but now they compute it as unsigned long.
Verified by objdump: the contents and relocations of
.data..percpu..shared_aligned are unchanged on 32-bit and 64-bit
kernels.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/8fc39fa3f6c5d635e93afbdd1a0fe0678a6d7913.1425611534.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It has nothing to do with init -- there's only one TSS per cpu.
Other names considered include:
- current_tss: Confusing because we never switch the tss.
- singleton_tss: Too long.
This patch was generated with 's/init_tss/cpu_tss/g'. Followup
patches will fix INIT_TSS and INIT_TSS_IST by hand.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/da29fb2a793e4f649d93ce2d1ed320ebe8516262.1425611534.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The ia32 sysenter code loaded the top of the kernel stack into
rsp by loading kernel_stack and then adjusting it. It can be
simplified to just read sp0 directly.
This requires the addition of a new asm-offsets entry for sp0.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/88ff9006163d296a0665338585c36d9bfb85235d.1425611534.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This will make modifying the semantics of kernel_stack easier.
The change to ist_begin_non_atomic() is necessary because sp0 no
longer points to the same THREAD_SIZE-aligned region as RSP;
it's one byte too high for that. At Denys' suggestion, rather
than offsetting it, just check explicitly that we're in the
correct range ending at sp0. This has the added benefit that we
no longer assume that the thread stack is aligned to
THREAD_SIZE.
Suggested-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/ef8254ad414cbb8034c9a56396eeb24f5dd5b0de.1425611534.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We currently store references to the top of the kernel stack in
multiple places: kernel_stack (with an offset) and
init_tss.x86_tss.sp0 (no offset). The latter is defined by
hardware and is a clean canonical way to find the top of the
stack. Add an accessor so we can start using it.
This needs minor paravirt tweaks. On native, sp0 defines the
top of the kernel stack and is therefore always correct. On Xen
and lguest, the hypervisor tracks the top of the stack, but we
want to start reading sp0 in the kernel. Fixing this is simple:
just update our local copy of sp0 as well as the hypervisor's
copy on task switches.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/8d675581859712bee09a055ed8f785d80dac1eca.1425611534.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
net/ipv4/fib_trie.c: In function ‘fib_table_flush_external’:
net/ipv4/fib_trie.c:1572:6: warning: unused variable ‘found’ [-Wunused-variable]
int found = 0;
^
net/ipv4/fib_trie.c:1571:16: warning: unused variable ‘slen’ [-Wunused-variable]
unsigned char slen;
^
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman says:
====================
switchdev: add IPv4 routing offload
v4:
- Add NETIF_F_NETNS_LOCAL to rocker port feature list to keep rocker
ports in the default netns. Rocker hardware can't be partitioned
to support multiple namespaces, currently. It would be interesting
to add netns support to rocker device by basically adding another
match field to each table to match on some unique netns ID, with
a port knowing it's netns ID. Future work TDB.
- Up-level the RTNH_F_EXTERNAL marking of routes installed to offload
device from driver to switchdev common code. Now driver can't skip
routes. Either it can install the route or it cannot. Yes or No.
If no on any route, all offloading is aborted by removing routes
from offload device and setting ipv4.fib_offload_disabled so no more
routes can be offloaded. This is harsh, but it's our starting point.
We can refine the policies in follow-up work.
- Add new net.ipv4.fib_offload_disabled bool that is set if anything
goes wrong with route offloading. We can refine this later to make
the setting per-device or per-device-port-netdev, but let's start
here simple and refine in follow-up work.
- Rebase against Alex's latest FIB changes. I think I did everything
correctly, and didn't run into any issues with testing, but I'd like
Alex to look over the changes and maybe follow-up with any cleanups.
v3:
Changes based on v2 review comments:
- Move check for custom rules up earlier in patch set, to keep git bisect
safe.
- Simplify the route add/modify failure handling to simple try until
failure, and then on failure, undo everything. The switchdev driver
will return err when route can normally be installed to device, but
the install fails for one reason or another (no space left on device,
etc). If a failure happens, uninstall all routes from the device,
punting forwarding for all routes back to the kernel.
- Scan route's full nexthop list, ensuring all nexthop devs belong
to the same switchdev device, otherwise don't try to install route
to device.
v2:
Changes based on v1 review comments and discussions at netconf:
- Allow route modification, but use same ndo op used for adding route.
Driver/device is expected to modify route in-place, if it can, to avoid
interruption of service.
- Add new RTNH_F_EXTERNAL flag to mark FIB entries offloaded externally.
- Don't offload routes if using custom IP rules. If routes are already
offloaded, and custom IP rules are turned on, flush routes from offload
device. (Offloaded routes are marked with RTNH_F_EXTERNAL).
- Use kernel's neigh resolution code to resolve route's nexthops' neigh
MAC addrs. (Thanks davem, works great!).
- Use fib->fib_priority in rocker driver to give priorities to routes in
OF-DPA unicast route table.
v1:
This patch set adds L3 routing offload support for IPv4 routes. The idea is to
mirror routes installed in the kernel's FIB down to a hardware switch device to
offload the data forwarding path for L3. Only the data forwarding path is
intercepted. Control and management of the kernel's FIB remains with the
kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver implements ndo_switch_fib_ipv4_add/del ops to add/del/mod IPv4
routes to/from switchdev device. Once a route is added to the device, and the
route's nexthops are resolved to neighbor MAC address, the device will forward
matching pkts rather than the kernel. This offloads the L3 forwarding path
from the kernel to the device. Note that control and management planes are
still mananged by Linux; only the data plane is offloaded. Standard routing
control protocols such as OSPF and BGP run on Linux and manage the kernel's FIB
via standard rtm netlink msgs...nothing changes here.
A new hash table is added to rocker to track neighbors. The driver listens for
neighbor updates events using netevent notifier NETEVENT_NEIGH_UPDATE. Any ARP
table updates for ports on this device are recorded in this table. Routes
installed to the device with nexthops that reference neighbors in this table
are "qualified". In the case of a route with nexthops not resolved in the
table, the kernel is asked to resolve the nexthop.
The driver uses fib_info->fib_priority for the priority field in rocker's
unicast routing table.
The device can only forward to pkts matching route dst to resolved nexthops.
Currently, the device only supports single-path routes (i.e. routes with one
nexthop). Equal Cost Multipath (ECMP) route support will be added in followup
patches.
This patch is driver support for unicast IPv4 routing only. Followup patches
will add driver and infrastructure for IPv6 routing and multicast routing.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call into the switchdev driver any time an IPv4 fib entry is
added/modified/deleted from the kernel's FIB. The switchdev driver may or
may not install the route to the offload device. In the case where the
driver tries to install the route and something goes wrong (device's routing
table is full, etc), then all of the offloaded routes will be flushed from the
device, route forwarding falls back to the kernel, and no more routes are
offloading.
We can refine this logic later. For now, use the simplist model of offloading
routes up to the point of failure, and then on failure, undo everything and
mark IPv4 offloading disabled.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If something goes wrong with IPv4 FIB offload, mark entire net offload
disabled. This is brute force policy to basically shut down IPv4 FIB offload
permanently if there is a problem offloading any route to an external device.
We can refine the policy in the future, to handle failures on a per-device or
per-route basis, but for now, this policy is per-net.
What we're trying to avoid is an inconsistent split between the kernel's FIB
and the offload device's FIB. We don't want the device to fwd a pkt
inconsitent with what the kernel would do. An example of a split is if device
has 10.0.0.0/16 and kernel has 10.0.0.0/16 and 10.0.0.0/24, the device wouldn't
see the longest prefix 10.0.0.0/24 and potentially forward pkts incorrectly.
Limited capacity or limited capability are two ways a route may fail to install
to the offload device. We'll not differentiate between failures at this time,
and treat any failure as fatal and mark the net as fib_offload_disabled.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flesh out ndo wrappers to call into device driver. To call into device driver,
the wrapper must interate over route's nexthops to ensure all nexthop devs
belong to the same switch device. Currently, there is no support for route's
nexthops spanning offloaded and non-offloaded devices, or spanning ports of
multiple offload devices.
Since switch device ports may be stacked under virtual interfaces (bonds and/or
bridges), and the route's nexthop may be on the virtual interface, the wrapper
will traverse the nexthop dev down to the base dev. It's the base dev that's
passed to the switchdev driver's ndo ops.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep switchdev FIB offload model simple for now and don't allow custom ip
rules.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 fib ndo wrapper funcs and stub them out for now.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new ndo ops for IPv4 fib offload support, add and del. Add uses
modifiy semantics if fib entry already offloaded. Drivers implementing the new
ndo ops will return err<0 if programming device fails, for example if device's
tables are full.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new RTNH_F_EXTERNAL flag to mark fib entries offloaded externally, for
example to a switchdev switch device.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: code re-organization
This pull request contains the first part of the patches required to implement
the grand plan detailed here:
http://www.spinics.net/lists/netdev/msg295942.html
These are mostly code re-organization and function bodies re-arrangement to
allow different callers of lower-level initialization functions for 'struct
dsa_switch' and 'struct dsa_switch_tree' to be later introduced.
There is no functional code change at this point.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the core logic that setups a 'struct dsa_switch_tree' and
removes it, update dsa_probe() and dsa_remove() to use the two helper
functions. This will be useful to allow for other callers to setup
this structure differently.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support the new DSA device driver model, a dsa_switch should
be able to advertise the type of tagging protocol supported by the
underlying switch device. This also removes constraints on how tagging
can be stacked to each other.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the part of dsa_switch_setup() which is responsible for allocating
and initializing a 'struct dsa_switch' and the part which is doing a
given switch device setup and slave network device creation.
This is a preliminary change to allow a separate caller of
dsa_switch_setup_one() which may have externally initialized the
dsa_switch structure, outside of dsa_switch_setup().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing a different model to register DSA switches,
update dsa_of_probe() and dsa_probe() to return -EPROBE_DEFER where
appropriate.
Failure to find a phandle or Device Tree property is still fatal, but
looking up the internal device structure associated with a Device Tree
node is something that might need to be delayed based on driver probe
ordering.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing a different mechanism to register DSA switch
devices and driver, update dsa_of_probe and dsa_of_remove to take a
struct device pointer since neither of these two functions uses the
struct platform_device pointer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
imx25-pdk.dts provides a more complete support than the board file version, so
let's get rid of the board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In xgene_pcie_map_bus(), we neglected to add in the register offset when
calculating the config space address. This means all config accesses
operated on the first four bytes of config space.
Add the register offset to the config space base address.
Also correct the xgene_pcie_map_bus() prototype to fix a compiler warning.
[bhelgaas: changelog]
Fixes: 350f8be5bb ("PCI: xgene: Convert to use generic config accessors")
Posting: http://lkml.kernel.org/r/1424214840-26498-1-git-send-email-fkan@apm.com
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
Acked-by: Rob Herring <robh@kernel.org>
timewait sockets now share a common base with established sockets.
inet_twsk_diag_dump() can use inet_diag_bc_sk() instead of duplicating
code, granted that inet_diag_bc_sk() does proper userlocks
initialization.
twsk_build_assert() will catch any future changes that could break
the assumptions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some mss values, it is possible tcp_xmit_size_goal() puts
one segment more in TSO packet than tcp_tso_autosize().
We send then one TSO packet followed by one single MSS.
It is not a serious bug, but we can do slightly better, especially
for drivers using netif_set_gso_max_size() to lower gso_max_size.
Using same formula avoids these corner cases and makes
tcp_xmit_size_goal() a bit faster.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 605ad7f184 ("tcp: refine TSO autosizing")
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver is removed (e.g. using unbind through sysfs), the
clocks get disabled twice, once on fec_enet_close and once on
fec_drv_remove. Since the clocks are enabled only once, this leads
to a warning:
WARNING: CPU: 0 PID: 402 at drivers/clk/clk.c:992 clk_core_disable+0x64/0x68()
Remove the call to fec_enet_clk_enable in fec_drv_remove to balance
the clock enable/disable calls again. This has been introduce by
e8fcfcd568 ("net: fec: optimize the clock management to save power").
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest spec "I-IPA01-0266-USR Rev 10" limit the MID field length to 12 bit
value. For previous versions it is 16 bit value.
This change will not break the backward compatibility as the latest ID value is
7 and with in the 12 bit value limit.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
