The thermal IP block (Thermal Management Unit) called TMU has been
enabled in this device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The standard code path accommodates a condition when no
RCU callbacks are ready to invoke. Since size of the code
is a priority for tiny RCU, remove the fast path.
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
When the ->curtail and ->donetail pointers differ, ->rcucblist
always points to the beginning of the current list and thus
cannot be NULL. Therefore, the check ->rcucblist != NULL is
redundant and this commit removes it.
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
On second and subsequent passes through quiescent-state forcing, the
isidle variable was initialized to false, which would prevent full sysidle
state from being reached if a grace period needed more than one round
of quiescent-state forcing (which most should not). However, the check
for offline CPUs in the quiescent-state forcing main loop had the wrong
sense, which could prevent CPUs from ever entering full sysidle state.
This commit fixes both of these bugs. Given that sysidle is not yet
wired up, this has no effect in old kernels, but might have proven
frustrating had anyone attempted to wire it up.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The current minstrel_ht rate control behavior is somewhat optimistic in
trying to find optimum TX rate. While this is usually fine for normal
Data frames, there are cases where a more conservative set of retry
parameters would be beneficial to make the connection more robust.
EAPOL frames are critical to the authentication and especially the
EAPOL-Key message 4/4 (the last message in the 4-way handshake) is
important to get through to the AP. If that message is lost, the only
recovery mechanism in many cases is to reassociate with the AP and start
from scratch. This can often be avoided by trying to send the frame with
more conservative rate and/or with more link layer retries.
In most cases, minstrel_ht is currently using the initial EAPOL-Key
frames for probing higher rates and this results in only five link layer
transmission attempts (one at high(ish) MCS and four at MCS0). While
this works with most APs, it looks like there are some deployed APs that
may have issues with the EAPOL frames using HT MCS immediately after
association. Similarly, there may be issues in cases where the signal
strength or radio environment is not good enough to be able to get
frames through even at couple of MCS 0 tries.
The best approach for this would likely to be to reduce the TX rate for
the last rate (3rd rate parameter in the set) to a low basic rate (say,
6 Mbps on 5 GHz and 2 or 5.5 Mbps on 2.4 GHz), but doing that cleanly
requires some more effort. For now, we can start with a simple one-liner
that forces the minimum rate to be used for EAPOL frames similarly how
the TX rate is selected for the IEEE 802.11 Management frames. This does
result in a small extra latency added to the cases where the AP would be
able to receive the higher rate, but taken into account how small number
of EAPOL frames are used, this is likely to be insignificant. A future
optimization in the minstrel_ht design can also allow this patch to be
reverted to get back to the more optimized initial TX rate.
It should also be noted that many drivers that do not use minstrel as
the rate control algorithm are already doing similar workarounds by
forcing the lowest TX rate to be used for EAPOL frames.
Cc: stable@vger.kernel.org
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "if" statement at the beginning of rcu_torture_writer() should
use the same set of variables. In theory, this does not matter because
the corresponding variables (gp_sync and gp_sync1) have the same value
at this point in the code, but in practice such puzzles should be
removed. This commit therefore makes the use of variables consistent.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit adds a CONFIG_RCU_EXPEDITE_BOOT Kconfig parameter
that emulates a very early boot rcu_expedite_gp(). A late-boot
call to rcu_end_inkernel_boot() will provide the corresponding
rcu_unexpedite_gp(). The late-boot call to rcu_end_inkernel_boot()
should be made just before init is spawned.
According to Arjan:
> To show the boot time, I'm using the timestamp of the "Write protecting"
> line, that's pretty much the last thing we print prior to ring 3 execution.
>
> A kernel with default RCU behavior (inside KVM, only virtual devices)
> looks like this:
>
> [ 0.038724] Write protecting the kernel read-only data: 10240k
>
> a kernel with expedited RCU (using the command line option, so that I
> don't have to recompile between measurements and thus am completely
> oranges-to-oranges)
>
> [ 0.031768] Write protecting the kernel read-only data: 10240k
>
> which, in percentage, is an 18% improvement.
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Arjan van de Ven <arjan@linux.intel.com>
This commit updates open-coded tests of the rcu_expedited variable
to instead use rcu_gp_is_expedited().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Currently, expediting of normal synchronous grace-period primitives
(synchronize_rcu() and friends) is controlled by the rcu_expedited()
boot/sysfs parameter. This works well, but does not handle nesting.
This commit therefore provides rcu_expedite_gp() to enable expediting
and rcu_unexpedite_gp() to cancel a prior rcu_expedite_gp(), both of
which support nesting.
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
In the past, it has been useful to enable PROVE_LOCKING without also
enabling PROVE_RCU. However, experience with PROVE_RCU over the past
few years has demonstrated its usefulness, so this commit makes
PROVE_LOCKING directly imply PROVE_RCU.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
When a CPU comes online, it initializes its callback list. This
is a bad thing if this is the first time that the CPU has come
online and if that CPU has early boot callbacks. This commit therefore
avoid initializing the callback list if there are callbacks present,
in which case the initial call_rcu() did the initialization for us.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Some diagnostics under CONFIG_PROVE_RCU in rcu_nocb_cpu_needs_barrier()
assume that there can be no early-boot callbacks. This commit therefore
qualifies the diagnostic with rcu_scheduler_fully_active to permit
early boot callbacks to avoid this splat.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Currently, a call_rcu() that precedes rcu_init() will splat due to the
callback lists not having yet been initialized. This commit causes the
first such callback to initialize the boot CPU's RCU callback list.
Note that this commit does not change rcu_init()-time initialization,
which means that the callback will be discarded at rcu_init() time.
Fixing this is the job of later commits.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit wires up the rcu_state structures' ->rda pointers to the
per-CPU rcu_data structures at compile time, thus ensuring that this
linkage is present at early boot, in turn allowing posting of callbacks
before rcu_init() is executed.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
In preparation for early-boot posting of callbacks, this commit abstracts
initialization of the default (non-no-CB) callbacks list from the
init_callback_list() function into a new init_default_callback_list()
function.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit explicitly states that control dependencies pair normally
with other barriers, and gives an example of such pairing.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
All value-returning atomic read-modify-write operations must provide full
memory-barrier semantics on both sides of the operation. This commit
clarifies the documentation to make it clear that these memory-barrier
semantics are provided by the operations themselves, not by their callers.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
POSIX timers are no longer starved on adaptive-ticks CPUs. Instead, they
prevent affected CPUs from entering adaptive-ticks mode. This commit
therefore updates the NO_HZ.txt documentation.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Now that the on-demand vmstat workers commit is in mainline, it is
possible to eliminate vmstat_update()-induced OS jitter. This commit
updates the documentation accordingly.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Now that the rcutree.kthread_prio kernel boot parameter also controls
the priority of the grace-period kthreads, update the documentation to
reflect this change.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit enables the cpufreq subsystem. Moreover, support
for using CPU as a cooling device is provided.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
After Exynos TMU rework to use device tree for configuration
this flag can be removed. It is not used anymore.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add pcie[01] node labels to allow to reference them easily from
board level.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
We want to enforce the use of named flags in GPIO and interrupt
specifiers, include the corresponding headers to Dove's SoC dtsi.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fix Dove's register addresses of uart2 and uart3 nodes that seem to
be broken since ages due to a copy-and-paste error.
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Linksys WRT1900AC (Mamba) is a router that has
- 2 mini-PCIe slots with Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6172 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 256MB RAM
gregory.clement@free-electrons.com: - add ARM to the title
- fix the reference to CONFIG_DEBUG_MVEBU_UART0_ALTERNATE
- fix the unbalanced comment for the syscfg partition
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Define videoports and use endpoints to describe the connection between
the encoder, bridge and the panel, instead of using phandles.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Define videoports and use endpoints to describe the connection between
the encoder, bridge and the panel, instead of using phandles.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Enabling SDIO IRQ signalling for the wifi MMC/SDIO slot
doubles the transmission transfer rate.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Snow board has a MMC/SDIO wifi chip that is always powered but it
needs a power sequence involving a reset (active low) and an enable
(active high) pins. Both pins are marked as active low since the MMC
simple power sequence driver asserts the pins prior to the card power
up procedure and de-asserts the pins after the card has been powered.
So the reset line will be left de-asserted and the enable pin will be
left asserted.
The chip also needs an external 32kHz reference clock to be operational
that is by the MAX77686 PMIC clock.
Add a simple MMC power sequence provider for the wifi MMC/SDIO slot.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This printk leads to the following Smatch warning:
drivers/gpu/drm/i915/i915_gem_gtt.c:336 alloc_pt_range()
error: '%pa' expects argument of type 'phys_addr_t*',
argument 5 has type 'struct i915_page_table_entry*'
It looks like a simple typo to me where "%p" was intended instead of
"%pa".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most of changes in this pull request are about the fixes of crash of
FireWire drivers at hot-unplugging. In addition, there are a few
HD-audio fixes (removal of wrong static, a pin quirk for an ASUS mobo,
a regression fix for runtime PM on Panther Point) and a long-standing
(but fairly minor) bug of PCM core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lgJD
-----END PGP SIGNATURE-----
Merge tag 'sound-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Most of changes in this pull request are about the fixes of crash of
FireWire drivers at hot-unplugging. In addition, there are a few
HD-audio fixes (removal of wrong static, a pin quirk for an ASUS mobo,
a regression fix for runtime PM on Panther Point) and a long-standing
(but fairly minor) bug of PCM core"
* tag 'sound-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Disable runtime PM for Panther Point again
ALSA: hda: controller code - do not export static functions
ALSA: pcm: Don't leave PREPARED state after draining
ALSA: fireworks/bebob/dice/oxfw: make it possible to shutdown safely
ALSA: fireworks/bebob/dice/oxfw: allow stream destructor after releasing runtime
ALSA: firewire-lib: remove reference counting
ALSA: fireworks/bebob/dice/oxfw: add reference-counting for FireWire unit
ALSA: hda - Add pin configs for ASUS mobo with IDT 92HD73XX codec
ALSA: firewire-lib: fix an unexpected byte sequence for micro sign
Patch 2f896d5866 ("arm64: use fixmap for text patching") changed
the way we patch the kernel text, using a fixmap when the kernel or
modules are flagged as read only.
Unfortunately, a flaw in the logic makes it fall over when patching
modules without CONFIG_DEBUG_SET_MODULE_RONX enabled:
[...]
[ 32.032636] Call trace:
[ 32.032716] [<fffffe00003da0dc>] __copy_to_user+0x2c/0x60
[ 32.032837] [<fffffe0000099f08>] __aarch64_insn_write+0x94/0xf8
[ 32.033027] [<fffffe000009a0a0>] aarch64_insn_patch_text_nosync+0x18/0x58
[ 32.033200] [<fffffe000009c3ec>] ftrace_modify_code+0x58/0x84
[ 32.033363] [<fffffe000009c4e4>] ftrace_make_nop+0x3c/0x58
[ 32.033532] [<fffffe0000164420>] ftrace_process_locs+0x3d0/0x5c8
[ 32.033709] [<fffffe00001661cc>] ftrace_module_init+0x28/0x34
[ 32.033882] [<fffffe0000135148>] load_module+0xbb8/0xfc4
[ 32.034044] [<fffffe0000135714>] SyS_finit_module+0x94/0xc4
[...]
This is triggered by the use of virt_to_page() on a module address,
which ends to pointing to Nowhereland if you're lucky, or corrupt
your precious data if not.
This patch fixes the logic by mimicking what is done on arm:
- If we're patching a module and CONFIG_DEBUG_SET_MODULE_RONX is set,
use vmalloc_to_page().
- If we're patching the kernel and CONFIG_DEBUG_RODATA is set,
use virt_to_page().
- Otherwise, use the provided address, as we can write to it directly.
Tested on 4.0-rc1 as a KVM guest.
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull btrfs fix from Chris Mason:
"I'm still testing more fixes, but I wanted to get out the fix for the
btrfs raid5/6 memory corruption I mentioned in my merge window pull"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix allocation size calculations in alloc_btrfs_bio
This patch increases the interleave factor for parallel AES modes
to 4x. This improves performance on Cortex-A57 by ~35%. This is
due to the 3-cycle latency of AES instructions on the A57's
relatively deep pipeline (compared to Cortex-A53 where the AES
instruction latency is only 2 cycles).
At the same time, disable inline expansion of the core AES functions,
as the performance benefit of this feature is negligible.
Measured on AMD Seattle (using tcrypt.ko mode=500 sec=1):
Baseline (2x interleave, inline expansion)
------------------------------------------
testing speed of async cbc(aes) (cbc-aes-ce) decryption
test 4 (128 bit key, 8192 byte blocks): 95545 operations in 1 seconds
test 14 (256 bit key, 8192 byte blocks): 68496 operations in 1 seconds
This patch (4x interleave, no inline expansion)
-----------------------------------------------
testing speed of async cbc(aes) (cbc-aes-ce) decryption
test 4 (128 bit key, 8192 byte blocks): 124735 operations in 1 seconds
test 14 (256 bit key, 8192 byte blocks): 92328 operations in 1 seconds
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Caught during Trinity testing. The pte_modify does not allow
modification for PTE type bit. This cause the test to hang
the system. It is found that the PTE can't transit from an
inaccessible page (b00) to a valid page (b11) because the mask
does not allow it. This happens when a big block of mmaped
memory is set the PROT_NONE, then the a small piece is broken
off and set to PROT_WRITE | PROT_READ cause a huge page split.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The functions __cpu_flush_user_tlb_range and __cpu_flush_kern_tlb_range
were removed in commit fa48e6f780 'arm64: mm: Optimise tlb flush logic
where we have >4K granule'. Global variable cpu_tlb was never used in
arm64.
Remove them.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
An arm64 allmodconfig fails to build with GCC 5 due to __asmeq
assertions in the PSCI firmware calling code firing due to mcount
preambles breaking our assumptions about register allocation of function
arguments:
/tmp/ccDqJsJ6.s: Assembler messages:
/tmp/ccDqJsJ6.s:60: Error: .err encountered
/tmp/ccDqJsJ6.s:61: Error: .err encountered
/tmp/ccDqJsJ6.s:62: Error: .err encountered
/tmp/ccDqJsJ6.s:99: Error: .err encountered
/tmp/ccDqJsJ6.s💯 Error: .err encountered
/tmp/ccDqJsJ6.s:101: Error: .err encountered
This patch fixes the issue by moving the PSCI calls out-of-line into
their own assembly files, which are safe from the compiler's meddling
fingers.
Reported-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The vdso implementation of clock_getres currently returns 0 (success)
whenever a null timespec is provided by the caller, regardless of the
clock id supplied.
This behavior is incorrect. It should fall back to syscall when an
unrecognized clock id is passed, even when the timespec argument is
null. This ensures that clock_getres always returns an error for
invalid clock ids.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Remove redundant call to ch341_close from error path when submission of
the interrupt urb fails in open.
Signed-off-by: Johan Hovold <johan@kernel.org>
On VLV/CHV the media well rc6 residency gets reported separately
from the render well, so add another file to sysfs so that we can
report the residency to the user.
Testcase: igt/pm_rc6_residency --run-subtest media-rc6-accuracy
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently an enabled break state is not disabled on final close nor on
re-open and has to be disabled manually.
Fix this by disabling break on port shutdown.
Reported-by: Jari Ruusu <jariruusu@users.sourceforge.net>
Tested-by: Jari Ruusu <jariruusu@users.sourceforge.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
my previous patch skipped vlan range optimizations during skb size
calculations for simplicity.
This incremental patch considers vlan ranges during
skb size calculations. This leads to a bit of code duplication
in the fill and size calculation functions. But, I could not find a
prettier way to do this. will take any suggestions.
Previously, I had reused the existing br_get_link_af_size size calculation
function to calculate skb size for notifications. Reusing it this time
around creates some change in behaviour issues for the usual
.get_link_af_size callback.
This patch adds a new br_get_link_af_size_filtered() function to
base the size calculation on the incoming filter flag and include
vlan ranges.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman says:
====================
rocker cleanups
Pushing out some rocker cleanups I've had in my queue for a while. Nothing
major, just some sync-up with changes that already went into device code
(hard-coding desc err return values and lport renaming). Also fixup
port fowarding transitions prompted by some DSA discussions about how to
restore port state when port leaves bridge.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
