Add the missing reset entry for the `SYS` module in the clock driver. The
corresponding core clock entry for `SYS` is already present.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250102181839.352599-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock structure for RZ/G3E is almost identical to RZ/V2H SoC with
more IP blocks compared to RZ/V2H. For eg: VSPI, LVDS, DPI and LCDC1
are present only on the RZ/G3E SoC.
Add minimal clock and reset entries required to boot the Renesas RZ/G3E
SMARC EVK and binds it with the RZ/V2H CPG core driver.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/20241213123550.289193-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The gcc_xo_clk is required for the functionality of the WiFi
copy engine block. Therefore, add the gcc_xo_clk in gcc driver.
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Link: https://lore.kernel.org/r/20241210064110.130466-3-quic_mmanikan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The gcc_apss_dbg clk is access protected by trust zone, and accessing
it results in a kernel crash. Therefore remove the gcc_apss_dbg_clk
from the gcc driver.
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Link: https://lore.kernel.org/r/20241217113909.3522305-2-quic_mmanikan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On APQ8064 the DSI2_PIXEL_SRC clock can be used either to drive the
second DSI host or to drive the LCDC controller. Add LVDS PLL as
possible source to the clock and LVDS output clock. The DSI2_PIXEL_SRC
clock has separate path to be used for the LVDS clock. To represent
both DSI and LVDS clocks properly, add intermediate clock which toggles
the enable bit and make DSI2_PIXEL_CLK clock just check for the HALT
bit.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241224-apq8064-fix-mmcc-v1-4-c95d2e2bf143@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
LVDS clocks require 1:1 ration support in the table used by
clk_rcg_pixel_ops. Add corresponding divider to the table.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241224-apq8064-fix-mmcc-v1-3-c95d2e2bf143@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The CMN PLL clock controller supplies clocks to the hardware
blocks that together make up the Ethernet function on Qualcomm
IPQ SoCs and to GCC. The driver is initially supported for
IPQ9574 SoC.
The CMN PLL clock controller expects a reference input clock
from the on-board Wi-Fi block acting as clock source. The input
reference clock needs to be configured to one of the supported
clock rates.
The controller supplies a number of fixed-rate output clocks.
For the IPQ9574, there is one output clock of 353 MHZ to PPE
(Packet Process Engine) hardware block, three 50 MHZ output
clocks and an additional 25 MHZ output clock supplied to the
connected Ethernet devices. The PLL also supplies a 24 MHZ
clock as XO and a 32 KHZ sleep clock to GCC, and one 31.25
MHZ clock to PCS.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250103-qcom_ipq_cmnpll-v8-2-c89fb4d4849d@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add driver for Display clock controller (DISPCC) in Qualcomm SM8750.
The device has several differences against SM8650, including new Pongo
PLLs and different clock parents, thus no compatibility or driver
re-usage.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250106-sm8750-dispcc-v2-3-6f42beda6317@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support for Pongo type of PLL clocks, used in Qualcomm SM8750 SoC.
Notable difference comparing to other PLLs is the need for calibration
for internally generated clock followed by wait_for_pll(). This is done
in configure call and at this time clocks are not yet registered, thus
wait_for_pll() cannot use clk_hw_get_name. Locking during this
calibration requires much more time, thus increase the timeout in
wait_for_pll().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250106-sm8750-dispcc-v2-2-6f42beda6317@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The TCSR clock controller found on SM8750 provides refclks
for PCIE, USB and UFS. Add clock driver for it.
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20241204-sm8750_master_clks-v3-8-1a8f31a53a86@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Update the match table for SC7280 to sort it in alphabetical order.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241204-sm8750_master_clks-v3-2-1a8f31a53a86@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
- Fix the CONFIG_RESET_CONTROLLER=n path signature of
clk_imx8mp_audiomix_reset_controller_register() to appease randconfig
- Speed up the sdhci clk on TH1520 by a factor of 4 by adding a fixed
factor clk
-----BEGIN PGP SIGNATURE-----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=30Sl
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A randconfig build fix and a performance fix:
- Fix the CONFIG_RESET_CONTROLLER=n path signature of
clk_imx8mp_audiomix_reset_controller_register() to appease
randconfig
- Speed up the sdhci clk on TH1520 by a factor of 4 by adding
a fixed factor clk"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: clk-imx8mp-audiomix: fix function signature
clk: thead: Fix TH1520 emmc and shdci clock rate
Stop force-selecting PLL-MIPI as TCON0 parent, since it breaks video
output on Pinebook that uses RGB to eDP bridge.
Partially revert commit ca1170b699 ("clk: sunxi-ng: a64: force
select PLL_MIPI in TCON0 mux"), while still leaving
CLK_SET_RATE_NO_REPARENT flag set, since we do not want the clock to
be reparented.
The issue is that apparently different TCON0 outputs require a different
clock, or the mux might be selecting the output type.
I did an experiment: I manually configured PLL_MIPI and PLL_VIDEO0_2X
to the same clock rate and flipped the switch with devmem. Experiment
clearly showed that whenever PLL_MIPI is selected as TCON0 clock parent,
the video output stops working.
Therefore, TCON0 clock parent corresponding to the output type must be
assigned in the device tree.
Fixes: ca1170b699 ("clk: sunxi-ng: a64: force select PLL_MIPI in TCON0 mux")
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Frank Oltmanns <frank@oltmanns.dev> # on PinePhone
Tested-by: Stuart Gathman <stuart@gathman.org> # on OG Pinebook
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Link: https://patch.msgid.link/20250104074035.1611136-5-anarsoul@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Drop redundant CLK_PLL_VIDEO0_2X and CLK_PLL.MIPI. These are now
defined in dt-bindings/clock/sun50i-a64-ccu.h
Fixes: ca1170b699 ("clk: sunxi-ng: a64: force select PLL_MIPI in TCON0 mux")
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Frank Oltmanns <frank@oltmanns.dev> # on pinephone
Tested-by: Stuart Gathman <stuart@gathman.org> # on OG pinebook
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Link: https://patch.msgid.link/20250104074035.1611136-3-anarsoul@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add clock support for SAMA7D65 SoC.
Increase maximum number of valid master clocks. The PMC for the SAMA7D65
requires 9 master clocks.
Increase maximum amount of PLLs to 9 to support SAMA7D65 SoC PLL
requirements.
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Link: https://lore.kernel.org/r/549fa8590fe9b4380e413f8eed87392f28754395.1734723585.git.Ryan.Wanner@microchip.com
[claudiu.beznea: sorted alphanumerically the Makefile entries, reorder
the code for resource cleanup in sama7d65_pmc_setup()]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
The Titan TOP GDSC is the parent GDSC for all other GDSCs in the CAMCC
block. None of the subordinate blocks will switch on without the parent
GDSC switched on.
Fixes: 76126a5129 ("clk: qcom: Add camcc clock driver for x1e80100")
Acked-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20241227-b4-linux-next-24-12-16-titan-top-gdsc-v1-1-c96ef62fc307@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
While testing the MMC nodes proposed in [1], it was noted that mmc0/1
would fail to initialize, with "mmc: fatal err update clk timeout" in
the kernel logs. A closer look at the clock definitions showed that the MMC
MPs had the "CLK_SET_RATE_NO_REPARENT" flag set. No reason was given for
adding this flag in the first place, and its original purpose is unknown,
but it doesn't seem to make sense and results in severe limitations to MMC
speeds. Thus, remove this flag from the 3 MMC MPs.
[1] https://msgid.link/20241024170540.2721307-10-masterr3c0rd@epochal.quest
Fixes: fb038ce4db ("clk: sunxi-ng: add support for the Allwinner A100 CCU")
Cc: stable@vger.kernel.org
Signed-off-by: Cody Eksal <masterr3c0rd@epochal.quest>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://patch.msgid.link/20241109003739.3440904-1-masterr3c0rd@epochal.quest
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Commit c45ae598fc ("clk: qcom: support for alpha mode configuration")
added support for configuring alpha mode, but it seems that the feature
was never working in practice.
The value of the alpha_{en,mode}_mask members of the configuration gets
added to the value parameter passed to the regmap_update_bits() function,
however the same values are not getting applied to the bitmask. As the
result, the respective bits in the USER_CTL register are never modifed
which leads to improper configuration of several PLLs.
The following table shows the PLL configurations where the 'alpha_en_mask'
member is set and which are passed as a parameter for the
clk_alpha_pll_configure() function. In the table the 'expected rate' column
shows the rate the PLL should run at with the given configuration, and
the 'real rate' column shows the rate the PLL runs at actually. The real
rates has been verified on hardwareOn IPQ* platforms, on other platforms,
those are computed values only.
file pll expected rate real rate
dispcc-qcm2290.c disp_cc_pll0 768.0 MHz 768.0 MHz
dispcc-sm6115.c disp_cc_pll0 768.0 MHz 768.0 MHz
gcc-ipq5018.c ubi32_pll 1000.0 MHz != 984.0 MHz
gcc-ipq6018.c nss_crypto_pll 1200.0 MHz 1200.0 MHz
gcc-ipq6018.c ubi32_pll 1497.6 MHz != 1488.0 MHz
gcc-ipq8074.c nss_crypto_pll 1200.0 MHz != 1190.4 MHz
gcc-qcm2290.c gpll11 532.0 MHz != 518.4 MHz
gcc-qcm2290.c gpll8 533.2 MHz != 518.4 MHz
gcc-qcs404.c gpll3 921.6 MHz 921.6 MHz
gcc-sm6115.c gpll11 600.0 MHz != 595.2 MHz
gcc-sm6115.c gpll8 800.0 MHz != 787.2 MHz
gpucc-sdm660.c gpu_cc_pll0 800.0 MHz != 787.2 MHz
gpucc-sdm660.c gpu_cc_pll1 740.0 MHz != 729.6 MHz
gpucc-sm6115.c gpu_cc_pll0 1200.0 MHz != 1190.4 MHz
gpucc-sm6115.c gpu_cc_pll1 640.0 MHz != 633.6 MHz
gpucc-sm6125.c gpu_pll0 1020.0 MHz != 1017.6 MHz
gpucc-sm6125.c gpu_pll1 930.0 MHz != 921.6 MHz
mmcc-sdm660.c mmpll8 930.0 MHz != 921.6 MHz
mmcc-sdm660.c mmpll5 825.0 MHz != 806.4 MHz
As it can be seen from the above, there are several PLLs which are
configured incorrectly.
Change the code to apply both 'alpha_en_mask' and 'alpha_mode_mask'
values to the bitmask in order to configure the alpha mode correctly.
Applying the 'alpha_en_mask' fixes the initial rate of the PLLs showed
in the table above. Since the 'alpha_mode_mask' is not used by any driver
currently, that part of the change causes no functional changes.
Cc: stable@vger.kernel.org
Fixes: c45ae598fc ("clk: qcom: support for alpha mode configuration")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20241021-fix-alpha-mode-config-v1-1-f32c254e02bc@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since both the 'alpha' and 'alpha_hi' members of the configuration is
initialized (the latter is implicitly) with zero values, the output
rate of the PLL will be the same whether alpha mode is enabled or not.
Remove the initialization of the alpha* members to make it clear that
the alpha mode is not required to get the desired output rate.
Despite that enabling alpha mode is not needed for the initial
configuration, the set_rate() op might require that it is enabled
already. In this particular case however, the clk_alpha_pll_set_rate()
function will get reset the ALPHA_EN bit when the PLL's rate changes,
so dropping 'alpha_en_mask' is safe.
No functional changes intended, compile tested only.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20241028-alpha-mode-cleanup-v2-5-9bc6d712bd76@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since both the 'alpha' and 'alpha_hi' members of the configuration is
initialized (the latter is implicitly) with zero values, the output
rate of the PLL will be the same whether alpha mode is enabled or not.
Remove the initialization of the alpha* members to make it clear that
the alpha mode is not required to get the desired output rate.
Despite that enabling alpha mode is not needed for the initial
configuration, the set_rate() op might require that it is enabled
already. In this particular case however, the clk_alpha_pll_set_rate()
function will get reset the ALPHA_EN bit when the PLL's rate changes,
so dropping 'alpha_en_mask' is safe.
No functional changes intended, compile tested only.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241028-alpha-mode-cleanup-v2-4-9bc6d712bd76@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since both the 'alpha' and 'alpha_hi' members of the configuration is
initialized with zero values, the output rate of the PLL will be the
same whether alpha mode is enabled or not.
Remove the initialization of the alpha* members to make it clear that
alpha mode is not required to get the desired output rate.
Despite that enabling alpha mode is not needed for the initial
configuration, the set_rate() op might require that it is enabled
already. In this particular case however, the clk_alpha_pll_set_rate()
function will get reset the ALPHA_EN bit when the PLL's rate changes,
so dropping 'alpha_en_mask' is safe.
While at it, also add a comment to indicate the frequency the PLL runs
at with the current configuration.
No functional changes, the PLL runs at 1.2 GHz both before and after
the change.
Tested on Xiaomi Mi Router AX1800 (IPQ6018, out-of-tree board).
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20241028-alpha-mode-cleanup-v2-3-9bc6d712bd76@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since neither 'alpha' nor 'alpha_hi' is defined in the configuration,
those will be initialized with zero values implicitly. By using zero
alpha values, the output rate of the PLL will be the same whether
alpha mode is enabled or not.
Remove the superfluous initialization of the 'alpha_en_mask' member
to make it clear that enabling alpha mode is not required to get the
desired output rate.
Despite that enabling alpha mode is not needed for the initial
configuration, the set_rate() op might require that it is enabled
already. In this particular case however, the
clk_alpha_pll_stromer_plus_set_rate() function will get reset the
ALPHA_EN bit when the PLL's rate changes, so dropping 'alpha_en_mask'
is safe.
While at it, also add a comment to indicate the frequency the PLL
runs at with the current configuration.
No functional changes, the initial rate of the PLL is the same both
before and after the patch.
Tested on Xiaomi Router BE3600 2.5G (IPQ5312, out-of-tree board).
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20241028-alpha-mode-cleanup-v2-2-9bc6d712bd76@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since neither 'alpha' nor 'alpha_hi' is defined in the configuration,
those will be initialized with zero values implicitly. By using zero
alpha values, the output rate of the PLL will be the same whether
alpha mode is enabled or not.
Remove the superfluous initialization of the 'alpha_en_mask' member
to make it clear that enabling alpha mode is not required to get the
desired output rate.
Despite that enabling alpha mode is not needed for the initial
configuration, the set_rate() op might require that it is enabled
already. In this particular case however, the
clk_alpha_pll_stromer_set_rate() function will get reset the
ALPHA_EN bit when the PLL's rate changes, so dropping 'alpha_en_mask'
is safe.
No functional changes, the initial rate of the PLL is the same both
before and after the patch.
Tested on TP-Link Archer AX55 v1 (IPQ5018).
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241028-alpha-mode-cleanup-v2-1-9bc6d712bd76@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
If a clk_rcg2 has a parent, it should also have parent_map defined,
otherwise we'll get a NULL pointer dereference when calling clk_set_rate
like the following:
[ 3.388105] Call trace:
[ 3.390664] qcom_find_src_index+0x3c/0x70 (P)
[ 3.395301] qcom_find_src_index+0x1c/0x70 (L)
[ 3.399934] _freq_tbl_determine_rate+0x48/0x100
[ 3.404753] clk_rcg2_determine_rate+0x1c/0x28
[ 3.409387] clk_core_determine_round_nolock+0x58/0xe4
[ 3.421414] clk_core_round_rate_nolock+0x48/0xfc
[ 3.432974] clk_core_round_rate_nolock+0xd0/0xfc
[ 3.444483] clk_core_set_rate_nolock+0x8c/0x300
[ 3.455886] clk_set_rate+0x38/0x14c
Add the parent_map property for the clock where it's missing and also
un-inline the parent_data as well to keep the matching parent_map and
parent_data together.
Fixes: 837519775f ("clk: qcom: Add display clock controller driver for SM6350")
Cc: stable@vger.kernel.org
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241220-sm6350-parent_map-v1-2-64f3d04cb2eb@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
If a clk_rcg2 has a parent, it should also have parent_map defined,
otherwise we'll get a NULL pointer dereference when calling clk_set_rate
like the following:
[ 3.388105] Call trace:
[ 3.390664] qcom_find_src_index+0x3c/0x70 (P)
[ 3.395301] qcom_find_src_index+0x1c/0x70 (L)
[ 3.399934] _freq_tbl_determine_rate+0x48/0x100
[ 3.404753] clk_rcg2_determine_rate+0x1c/0x28
[ 3.409387] clk_core_determine_round_nolock+0x58/0xe4
[ 3.421414] clk_core_round_rate_nolock+0x48/0xfc
[ 3.432974] clk_core_round_rate_nolock+0xd0/0xfc
[ 3.444483] clk_core_set_rate_nolock+0x8c/0x300
[ 3.455886] clk_set_rate+0x38/0x14c
Add the parent_map property for two clocks where it's missing and also
un-inline the parent_data as well to keep the matching parent_map and
parent_data together.
Fixes: 131abae905 ("clk: qcom: Add SM6350 GCC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241220-sm6350-parent_map-v1-1-64f3d04cb2eb@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
aggr_state and unit fields are u32. The result of their
multiplication may not fit in this type.
Add explicit casting to prevent overflow.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 04053f4d23 ("clk: qcom: clk-rpmh: Add IPA clock support")
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Link: https://lore.kernel.org/r/20241203084231.6001-1-abelova@astralinux.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable the LVDS gate, MIPI DSI, PXP, FLEXIO and MU only for i.MX93,
because i.MX91 does not support them.
Update enet clk entry format to align with others.
Fixes: a27bfff88d ("clk: imx: add i.MX91 clk")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241225001443.883131-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Split IMX93_CLK_SPDIF_IPG from IMX93_CLK_SPDIF_GATE
because the IMX93_CLK_SPDIF_GATE controls the gate
of IPG clock and root clock. Without this change,
disabling IMX93_CLK_SPDIF_GATE would also disable
the IPG clock, causing register access failures.
Fixes: 1c4a4f7362 ("arm64: dts: imx93: Add audio device nodes")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241119015805.3840606-3-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The PLL1416x is used to implement SYS_PLL3 on i.MX8MP and can be used
to drive CLKOUTn clock. Add 208 MHz and 416 MHz entries to the PLL so
they can be generated by the PLL and used to produce e.g. 13 MHz or
26 MHz on CLKOUTn output.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20241112013805.333798-1-marex@denx.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The CLKOUTn may be fed from PLL1/2/3, but the PLL1/2/3 has to be enabled
first by setting PLL_CLKE bit 11 in CCM_ANALOG_SYS_PLLn_GEN_CTRL register.
The CCM_ANALOG_SYS_PLLn_GEN_CTRL bit 11 is modeled by plln_out clock. Fix
the clock tree and place the clkout1/2 under plln_sel instead of plain plln
to let the clock subsystem correctly control the bit 11 and enable the PLL
in case the CLKOUTn is supplied by PLL1/2/3.
Fixes: 43896f56b5 ("clk: imx8mp: add clkout1/2 support")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20241112013718.333771-1-marex@denx.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
With PWRSTS_OFF_ON, PCIe GDSCs are turned off during gdsc_disable(). This
can happen during scenarios such as system suspend and breaks the resume
of PCIe controllers from suspend.
So use PWRSTS_RET_ON to indicate the GDSC driver to not turn off the GDSCs
during gdsc_disable() and allow the hardware to transition the GDSCs to
retention when the parent domain enters low power state during system
suspend.
Cc: stable@vger.kernel.org # 6.8
Fixes: c58225b7e3 ("clk: qcom: add the SM8650 Global Clock Controller driver, part 1")
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on QRD8650
Link: https://lore.kernel.org/r/20241219170011.70140-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
With PWRSTS_OFF_ON, PCIe GDSCs are turned off during gdsc_disable(). This
can happen during scenarios such as system suspend and breaks the resume
of PCIe controllers from suspend.
So use PWRSTS_RET_ON to indicate the GDSC driver to not turn off the GDSCs
during gdsc_disable() and allow the hardware to transition the GDSCs to
retention when the parent domain enters low power state during system
suspend.
Cc: stable@vger.kernel.org # 6.2
Fixes: 955f2ea3b9 ("clk: qcom: Add GCC driver for SM8550")
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on QRD8550
Link: https://lore.kernel.org/r/20241219170011.70140-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The 8-core X1s have a different GPU subsystem compared to their bigger
cousins, including the clocks part. Add the GPU clock controller driver
to drive these.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241221-topic-x1p4_clk-v1-3-dbaeccb74884@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>