Like the E3C246D4I, this is a reasonably affordable off-the-shelf
mini-ITX AST2500/Xeon motherboard with good potential as an OpenBMC
development platform. Booting the host requires a modicum of eSPI
support that's not yet in the mainline kernel, but most other basic
BMC functionality is available with this device-tree.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20240502002836.17862-8-zev@bewilderbeest.net
Signed-off-by: Joel Stanley <joel@jms.id.au>
The ISL69269 is a PMBus voltage regulator with no configurable
parameters.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240502002836.17862-6-zev@bewilderbeest.net
Signed-off-by: Joel Stanley <joel@jms.id.au>
Base on aspeed-g6.dtsi and can boot into BMC console.
Signed-off-by: Kelly Hung <ppighouse@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20240430045853.3894633-3-Kelly_Hung@asus.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Remove Facebook Cloudripper dts because the switch platform is not
actively maintained (all the units are deprecated).
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20240411045622.7915-1-rentao.bupt@gmail.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Enable I2C bus 8 which is exposed on the IPMB_1 connector on the X570D4U
mainboard.
Additionally adds a descriptive comment to I2C busses 1 and 5.
Signed-off-by: Renze Nicolai <renze@rnplus.nl>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Restructure GPIO table to fit maximum line length.
Fix mistakes found while working on OpenBMC userland configuration and
based on probing the board.
Schematic for this board is not available. Because of this the choice
was made to use a descriptive method for naming the GPIOs.
- Push-pull outputs start with output-*
- Open-drain outputs start with control-*
- LED outputs start with led-*
- Inputs start with input-*
- Button inputs start with button-*
- Active low signals end with *-n
Signed-off-by: Renze Nicolai <renze@rnplus.nl>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Since the ocp debug card only supports 100k, the bus is also set to 100k.
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
[AJ: Fixed fuzz due to prior IPMB patch]
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
The PCA chip for the NVMe LEDs is wired up backwards, so correct
the device tree labels.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
A recent change to the lm25066 driver changed the name of its
regulator from vout0 to vout; device-tree users of lm25066's regulator
functionality (of which ahe50dc is the only one) thus require a
corresponding update.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Due to the way i2c driver matching works (falling back to the driver's
id_table if of_match_table fails) this didn't actually cause any
misbehavior, but let's add the vendor prefixes so things actually work
the way they were intended to.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Like the more recently added ASRock BMC platforms, e3c246d4i and
romed8hm3 also have the BMC's MAC address available in the baseboard
FRU EEPROM, so let's add support for using it.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Added a device tree for IBM system1 BMC board, which uses AST2600 SoC.
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://lore.kernel.org/r/20240125212154.4028640-3-ninad@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Document the new compatibles used on IBM system1-bmc
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://lore.kernel.org/r/20240125212154.4028640-2-ninad@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Enable FSI interrupt controllers for AST2600 and P10BMC hub master.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20240215220759.976998-27-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Add the SGPIO line name that the project's function can use by the
meaningful name.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-12-yangchen.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Add the GPIO line name that the project's function can use by the
meaningful name.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-11-yangchen.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Add led-fan-fault gpio pin on the PCA9555 on the i2c bus 0.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-10-yangchen.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Add fan rpm controller max31790 on all bus of FCB.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-9-yangchen.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Add bus labels and aliases for the fan control board.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-8-yangchen.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Correct the address from 0x51 to 0x54 of eeprom on the i2c bus 1
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-7-yangchen.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Add one temperature sensor on i2c bus 1
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-6-yangchen.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Enable power monitor device ina230 and ltc2945 on the i2c bus 0
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-5-yangchen.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Correct the sgpio use from sgpiom1 to sgpiom0
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-4-yangchen.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Remove the unuse setting and fix the link to 100 M
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-3-yangchen.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
The project Minerva which is the platform used by Meta has two boards: the
Chassis Management Module (Minerva) and the Motherboard (Harma), so change
the DTS name to minerva here for CMM use.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-2-yangchen.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Add linux device tree entry related to
the Meta(Facebook) computer-node system use an AT2600 BMC.
This node is named "Harma".
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231211162656.2564267-3-peteryin.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Document the new compatibles used on Meta Harma.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20231211162656.2564267-2-peteryin.openbmc@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
