[ Upstream commit 0611f78f83 ]
When an invalid function ID of an SBI extension is used we should
return not-supported, not invalid-param. Also, when we see that at
least one hartid constructed from the base and mask parameters is
invalid, then we should return invalid-param. Finally, rather than
relying on overflowing a left shift to result in zero and then using
that zero in a condition which [correctly] skips sending an IPI (but
loops unnecessarily), explicitly check for overflow and exit the loop
immediately.
Fixes: 5f862df558 ("RISC-V: KVM: Add v0.1 replacement SBI extensions defined in v0.2")
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20250217084506.18763-10-ajones@ventanamicro.com
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3219b0c49 ]
The spec says suspend_type is 32 bits wide and "In case the data is
defined as 32bit wide, higher privilege software must ensure that it
only uses 32 bit data." Mask off upper bits of suspend_type before
using it.
Fixes: 763c8bed8c ("RISC-V: KVM: Implement SBI HSM suspend call")
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20250217084506.18763-9-ajones@ventanamicro.com
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7db342e3b ]
"Not stopped" means started or suspended so we need to check for
a single state in order to have a chance to check for each state.
Also, we need to use target_vcpu when checking for the suspend
state.
Fixes: 763c8bed8c ("RISC-V: KVM: Implement SBI HSM suspend call")
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20250217084506.18763-8-ajones@ventanamicro.com
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3126ea9be6 ]
The device tree of RK3568 did not specify reset-names before.
So add fallback to old behaviour to be compatible with old DT.
Fixes: fbcbffbac9 ("phy: rockchip: naneng-combphy: fix phy reset")
Cc: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250106100001.1344418-2-amadeus@jmu.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcf5d353b0 ]
A previous patch ensured that USB Type C connector support is enabled,
but it is still possible to build the phy driver without enabling
CONFIG_USB (host support) or CONFIG_USB_GADGET (device support), and
in that case the common helper functions are unavailable:
aarch64-linux-ld: drivers/phy/rockchip/phy-rockchip-usbdp.o: in function `rk_udphy_probe':
phy-rockchip-usbdp.c:(.text+0xe74): undefined reference to `usb_get_maximum_speed'
Select CONFIG_USB_COMMON directly here, like we do in some other phy
drivers, to make sure this is available even when actual USB support
is disabled or in a loadable module that cannot be reached from a
built-in phy driver.
Fixes: 9c79b77964 ("phy: rockchip: fix CONFIG_TYPEC dependency")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250122065249.1390081-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bebe35bb73 ]
I still have some Soekris net4826 in a Community Wireless Network I
volunteer with. These devices use an AMD SC1100 SoC. I am running
OpenWrt on them, which uses a patched kernel, that naturally has
evolved over time. I haven't updated the ones in the field in a
number of years (circa 2017), but have one in a test bed, where I have
intermittently tried out test builds.
A few years ago, I noticed some trouble, particularly when "warm
booting", that is, doing a reboot without removing power, and noticed
the device was hanging after the kernel message:
[ 0.081615] Working around Cyrix MediaGX virtual DMA bugs.
If I removed power and then restarted, it would boot fine, continuing
through the message above, thusly:
[ 0.081615] Working around Cyrix MediaGX virtual DMA bugs.
[ 0.090076] Enable Memory-Write-back mode on Cyrix/NSC processor.
[ 0.100000] Enable Memory access reorder on Cyrix/NSC processor.
[ 0.100070] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.110058] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[ 0.120037] CPU: NSC Geode(TM) Integrated Processor by National Semi (family: 0x5, model: 0x9, stepping: 0x1)
[...]
In order to continue using modern tools, like ssh, to interact with
the software on these old devices, I need modern builds of the OpenWrt
firmware on the devices. I confirmed that the warm boot hang was still
an issue in modern OpenWrt builds (currently using a patched linux
v6.6.65).
Last night, I decided it was time to get to the bottom of the warm
boot hang, and began bisecting. From preserved builds, I narrowed down
the bisection window from late February to late May 2019. During this
period, the OpenWrt builds were using 4.14.x. I was able to build
using period-correct Ubuntu 18.04.6. After a number of bisection
iterations, I identified a kernel bump from 4.14.112 to 4.14.113 as
the commit that introduced the warm boot hang.
07aaa7e3d6
Looking at the upstream changes in the stable kernel between 4.14.112
and 4.14.113 (tig v4.14.112..v4.14.113), I spotted a likely suspect:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=20afb90f730982882e65b01fb8bdfe83914339c5
So, I tried reverting just that kernel change on top of the breaking
OpenWrt commit, and my warm boot hang went away.
Presumably, the warm boot hang is due to some register not getting
cleared in the same way that a loss of power does. That is
approximately as much as I understand about the problem.
More poking/prodding and coaching from Jonas Gorski, it looks
like this test patch fixes the problem on my board: Tested against
v6.6.67 and v4.14.113.
Fixes: 18fb053f9b ("x86/cpu/cyrix: Use correct macros for Cyrix calls on Geode processors")
Debugged-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/CAHP3WfOgs3Ms4Z+L9i0-iBOE21sdMk5erAiJurPjnrL9LSsgRA@mail.gmail.com
Cc: Matthew Whitehead <tedheadster@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73cfc53cc3 ]
A C jump table (such as the one used by the BPF interpreter) is a const
global array of absolute code addresses, and this means that the actual
values in the table may not be known until the kernel is booted (e.g.,
when using KASLR or when the kernel VA space is sized dynamically).
When using PIE codegen, the compiler will default to placing such const
global objects in .data.rel.ro (which is annotated as writable), rather
than .rodata (which is annotated as read-only). As C jump tables are
explicitly emitted into .rodata, this used to result in warnings for
LoongArch builds (which uses PIE codegen for the entire kernel) like
Warning: setting incorrect section attributes for .rodata..c_jump_table
due to the fact that the explicitly specified .rodata section inherited
the read-write annotation that the compiler uses for such objects when
using PIE codegen.
This warning was suppressed by explicitly adding the read-only
annotation to the __attribute__((section(""))) string, by commit
c5b1184dec ("compiler.h: specify correct attribute for .rodata..c_jump_table")
Unfortunately, this hack does not work on Clang's integrated assembler,
which happily interprets the appended section type and permission
specifiers as part of the section name, which therefore no longer
matches the hard-coded pattern '.rodata..c_jump_table' that objtool
expects, causing it to emit a warning
kernel/bpf/core.o: warning: objtool: ___bpf_prog_run+0x20: sibling call from callable instruction with modified stack frame
Work around this, by emitting C jump tables into .data.rel.ro instead,
which is treated as .rodata by the linker script for all builds, not
just PIE based ones.
Fixes: c5b1184dec ("compiler.h: specify correct attribute for .rodata..c_jump_table")
Tested-by: Tiezhu Yang <yangtiezhu@loongson.cn> # on LoongArch
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20250221135704.431269-6-ardb+git@google.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06e2474598 ]
There are no users of annotate_reachable() left.
And the annotate_unreachable() usage in unreachable() is plain wrong;
it will hide dangerous fall-through code-gen.
Remove both.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lore.kernel.org/r/20241128094312.235637588@infradead.org
Stable-dep-of: 73cfc53cc3 ("objtool: Fix C jump table annotations for Clang")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c837de3810 ]
Since barrier_before_unreachable() is empty for !GCC it is trivial to
unify the two definitions. Less is more.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lore.kernel.org/r/20241128094311.924381359@infradead.org
Stable-dep-of: 73cfc53cc3 ("objtool: Fix C jump table annotations for Clang")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cde378a10 ]
params->total_weight is not initialized during bind and not updated when
the bound cdev changes. The cooling device weight will not be used due
to the uninitialized total_weight, until an update via sysfs is
triggered.
The bound cdevs are updated during thermal zone registration, where each
cooling device will be bound to the thermal zone one by one, but
power_allocator_bind() can be called without an additional cdev update
when manually changing the policy of a thermal zone via sysfs.
Add a new function to handle weight update logic, including updating
total_weight, and call it when bind, weight changes, and cdev updates to
ensure total_weight is always correct.
Fixes: a3cd6db4cc ("thermal: gov_power_allocator: Support new update callback of weights")
Signed-off-by: Yu-Che Cheng <giver@chromium.org>
Link: https://patch.msgid.link/20250222-fix-power-allocator-weight-v2-1-a94de86b685a@chromium.org
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dc23567c2 ]
In almost all places where a thermal zone's list of thermal instances
is walked, there is a check to match a specific trip point and it is
walked in vain whenever there are no cooling devices associated with
the given trip.
To address this, store the lists of thermal instances in trip point
descriptors instead of storing them in thermal zones and adjust all
code using those lists accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/5522726.Sb9uPGUboI@rjwysocki.net
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Stable-dep-of: 0cde378a10 ("thermal: gov_power_allocator: Update total_weight on bind and cdev updates")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 423de5b5bc ]
Since thermal_of_should_bind() terminates the loop after processing
the first child found in cooling-maps, it will never match more than
one cdev to a given trip point which is incorrect, as there may be
cooling-maps associating one trip point with multiple cooling devices.
Address this by letting the loop continue until either all
children have been processed or a matching one has been found.
To avoid adding conditionals or goto statements, put the loop in
question into a separate function and make that function return
right away after finding a matching cooling-maps entry.
Fixes: 94c6110b0b ("thermal/of: Use the .should_bind() thermal zone callback")
Link: https://lore.kernel.org/linux-pm/20250219-fix-thermal-of-v1-1-de36e7a590c4@chromium.org/
Reported-by: Yu-Che Cheng <giver@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Yu-Che Cheng <giver@chromium.org>
Tested-by: Yu-Che Cheng <giver@chromium.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/2788228.mvXUDI8C0e@rjwysocki.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69f3aa6ad9 ]
Use scoped for_each_child_of_node_scoped() when iterating over device
nodes to make code a bit simpler.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241010-b4-cleanup-h-of-node-put-thermal-v4-1-bfbe29ad81f4@linaro.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 423de5b5bc ("thermal/of: Fix cdev lookup in thermal_of_should_bind()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bddf10d26e ]
We triggered the following crash in syzkaller tests:
BUG: Bad page state in process syz.7.38 pfn:1eff3
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1eff3
flags: 0x3fffff00004004(referenced|reserved|node=0|zone=1|lastcpupid=0x1fffff)
raw: 003fffff00004004 ffffe6c6c07bfcc8 ffffe6c6c07bfcc8 0000000000000000
raw: 0000000000000000 0000000000000000 00000000fffffffe 0000000000000000
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x32/0x50
bad_page+0x69/0xf0
free_unref_page_prepare+0x401/0x500
free_unref_page+0x6d/0x1b0
uprobe_write_opcode+0x460/0x8e0
install_breakpoint.part.0+0x51/0x80
register_for_each_vma+0x1d9/0x2b0
__uprobe_register+0x245/0x300
bpf_uprobe_multi_link_attach+0x29b/0x4f0
link_create+0x1e2/0x280
__sys_bpf+0x75f/0xac0
__x64_sys_bpf+0x1a/0x30
do_syscall_64+0x56/0x100
entry_SYSCALL_64_after_hwframe+0x78/0xe2
BUG: Bad rss-counter state mm:00000000452453e0 type:MM_FILEPAGES val:-1
The following syzkaller test case can be used to reproduce:
r2 = creat(&(0x7f0000000000)='./file0\x00', 0x8)
write$nbd(r2, &(0x7f0000000580)=ANY=[], 0x10)
r4 = openat(0xffffffffffffff9c, &(0x7f0000000040)='./file0\x00', 0x42, 0x0)
mmap$IORING_OFF_SQ_RING(&(0x7f0000ffd000/0x3000)=nil, 0x3000, 0x0, 0x12, r4, 0x0)
r5 = userfaultfd(0x80801)
ioctl$UFFDIO_API(r5, 0xc018aa3f, &(0x7f0000000040)={0xaa, 0x20})
r6 = userfaultfd(0x80801)
ioctl$UFFDIO_API(r6, 0xc018aa3f, &(0x7f0000000140))
ioctl$UFFDIO_REGISTER(r6, 0xc020aa00, &(0x7f0000000100)={{&(0x7f0000ffc000/0x4000)=nil, 0x4000}, 0x2})
ioctl$UFFDIO_ZEROPAGE(r5, 0xc020aa04, &(0x7f0000000000)={{&(0x7f0000ffd000/0x1000)=nil, 0x1000}})
r7 = bpf$PROG_LOAD(0x5, &(0x7f0000000140)={0x2, 0x3, &(0x7f0000000200)=ANY=[@ANYBLOB="1800000000120000000000000000000095"], &(0x7f0000000000)='GPL\x00', 0x7, 0x0, 0x0, 0x0, 0x0, '\x00', 0x0, @fallback=0x30, 0xffffffffffffffff, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x10, 0x0, @void, @value}, 0x94)
bpf$BPF_LINK_CREATE_XDP(0x1c, &(0x7f0000000040)={r7, 0x0, 0x30, 0x1e, @val=@uprobe_multi={&(0x7f0000000080)='./file0\x00', &(0x7f0000000100)=[0x2], 0x0, 0x0, 0x1}}, 0x40)
The cause is that zero pfn is set to the PTE without increasing the RSS
count in mfill_atomic_pte_zeropage() and the refcount of zero folio does
not increase accordingly. Then, the operation on the same pfn is performed
in uprobe_write_opcode()->__replace_page() to unconditional decrease the
RSS count and old_folio's refcount.
Therefore, two bugs are introduced:
1. The RSS count is incorrect, when process exit, the check_mm() report
error "Bad rss-count".
2. The reserved folio (zero folio) is freed when folio->refcount is zero,
then free_pages_prepare->free_page_is_bad() report error
"Bad page state".
There is more, the following warning could also theoretically be triggered:
__replace_page()
-> ...
-> folio_remove_rmap_pte()
-> VM_WARN_ON_FOLIO(is_zero_folio(folio), folio)
Considering that uprobe hit on the zero folio is a very rare case, just
reject zero old folio immediately after get_user_page_vma_remote().
[ mingo: Cleaned up the changelog ]
Fixes: 7396fa818d ("uprobes/core: Make background page replacement logic account for rss_stat counters")
Fixes: 2b14449835 ("uprobes, mm, x86: Add the ability to install and remove uprobes breakpoints")
Signed-off-by: Tong Tiangen <tongtiangen@huawei.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20250224031149.1598949-1-tongtiangen@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2016066c66 ]
Syskaller triggers a warning due to prev_epc->pmu != next_epc->pmu in
perf_event_swap_task_ctx_data(). vmcore shows that two lists have the same
perf_event_pmu_context, but not in the same order.
The problem is that the order of pmu_ctx_list for the parent is impacted by
the time when an event/PMU is added. While the order for a child is
impacted by the event order in the pinned_groups and flexible_groups. So
the order of pmu_ctx_list in the parent and child may be different.
To fix this problem, insert the perf_event_pmu_context to its proper place
after iteration of the pmu_ctx_list.
The follow testcase can trigger above warning:
# perf record -e cycles --call-graph lbr -- taskset -c 3 ./a.out &
# perf stat -e cpu-clock,cs -p xxx // xxx is the pid of a.out
test.c
void main() {
int count = 0;
pid_t pid;
printf("%d running\n", getpid());
sleep(30);
printf("running\n");
pid = fork();
if (pid == -1) {
printf("fork error\n");
return;
}
if (pid == 0) {
while (1) {
count++;
}
} else {
while (1) {
count++;
}
}
}
The testcase first opens an LBR event, so it will allocate task_ctx_data,
and then open tracepoint and software events, so the parent context will
have 3 different perf_event_pmu_contexts. On inheritance, child ctx will
insert the perf_event_pmu_context in another order and the warning will
trigger.
[ mingo: Tidied up the changelog. ]
Fixes: bd27568117 ("perf: Rewrite core context handling")
Signed-off-by: Luo Gengkun <luogengkun@huaweicloud.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20250122073356.1824736-1-luogengkun@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ecaa75771 ]
divvy_up_power() should use weighted_req_power instead of req_power to
calculate granted_power. Otherwise, granted_power may be unexpected as
the denominator total_req_power is a weighted sum.
This is a mistake made during the previous refactor.
Replace req_power with weighted_req_power in divvy_up_power()
calculation.
Fixes: 912e97c67c ("thermal: gov_power_allocator: Move memory allocation out of throttle()")
Signed-off-by: Yu-Che Cheng <giver@chromium.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/20250219-fix-power-allocator-calc-v1-1-48b860291919@chromium.org
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54e1b4becf ]
IEP driver supports both perout and pps signal generation
but perout feature is faulty with half-cooked support
due to some missing configuration. Remove perout
support from the driver and reject perout requests with
"not supported" error code.
Fixes: c1e0230eea ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250227092441.1848419-1-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cbddbddee ]
Some drivers, like tg3, do not set combined-count:
$ ethtool -l enp4s0f1
Channel parameters for enp4s0f1:
Pre-set maximums:
RX: 4
TX: 4
Other: n/a
Combined: n/a
Current hardware settings:
RX: 4
TX: 1
Other: n/a
Combined: n/a
In the case where combined-count is not set, the ethtool netlink code
in the kernel elides the value and the code in the test:
netnl.channels_get(...)
With a tg3 device, the returned dictionary looks like:
{'header': {'dev-index': 3, 'dev-name': 'enp4s0f1'},
'rx-max': 4,
'rx-count': 4,
'tx-max': 4,
'tx-count': 1}
Note that the key 'combined-count' is missing. As a result of this
missing key the test raises an exception:
# Exception| if channels['combined-count'] == 0:
# Exception| ~~~~~~~~^^^^^^^^^^^^^^^^^^
# Exception| KeyError: 'combined-count'
Change the test to check if 'combined-count' is a key in the dictionary
first and if not assume that this means the driver has separate RX and
TX queues.
With this change, the test now passes successfully on tg3 and mlx5
(which does have a 'combined-count').
Fixes: 1cf2704242 ("net: selftest: add test for netdev netlink queue-get API")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: David Wei <dw@davidwei.uk>
Link: https://patch.msgid.link/20250226181957.212189-1-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d253726ff ]
Non IP flow, with vlan tag not working as expected while
running below command for vlan-priority. fixed that.
ethtool -N eth1 flow-type ether vlan 0x8000 vlan-mask 0x1fff action 0 loc 0
Fixes: 1274daede3 ("net: mvpp2: cls: Add steering based on vlan Id and priority.")
Signed-off-by: Harshal Chaudhari <hchaudhari@marvell.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250225042058.2643838-1-hchaudhari@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49806fe6e6 ]
In certain cases, napi_get_frags() returns an skb that points to an old
received fragment, This skb may have its skb->ip_summed, csum, and other
fields set from previous fragment handling.
Some network drivers set skb->ip_summed to either CHECKSUM_COMPLETE or
CHECKSUM_UNNECESSARY when getting skb from napi_get_frags(), while
others only set skb->ip_summed when RX checksum offload is enabled on
the device, and do not set any value for skb->ip_summed when hardware
checksum offload is disabled, assuming that the skb->ip_summed
initiated to zero by napi_reuse_skb, ionic driver for example will
ignore/unset any value for the ip_summed filed if HW checksum offload is
disabled, and if we have a situation where the user disables the
checksum offload during a traffic that could lead to the following
errors shown in the kernel logs:
<IRQ>
dump_stack_lvl+0x34/0x48
__skb_gro_checksum_complete+0x7e/0x90
tcp6_gro_receive+0xc6/0x190
ipv6_gro_receive+0x1ec/0x430
dev_gro_receive+0x188/0x360
? ionic_rx_clean+0x25a/0x460 [ionic]
napi_gro_frags+0x13c/0x300
? __pfx_ionic_rx_service+0x10/0x10 [ionic]
ionic_rx_service+0x67/0x80 [ionic]
ionic_cq_service+0x58/0x90 [ionic]
ionic_txrx_napi+0x64/0x1b0 [ionic]
__napi_poll+0x27/0x170
net_rx_action+0x29c/0x370
handle_softirqs+0xce/0x270
__irq_exit_rcu+0xa3/0xc0
common_interrupt+0x80/0xa0
</IRQ>
This inconsistency sometimes leads to checksum validation issues in the
upper layers of the network stack.
To resolve this, this patch clears the skb->ip_summed value for each
reused skb in by napi_reuse_skb(), ensuring that the caller is responsible
for setting the correct checksum status. This eliminates potential
checksum validation issues caused by improper handling of
skb->ip_summed.
Fixes: 76620aafd6 ("gro: New frags interface to avoid copying shinfo")
Signed-off-by: Mohammad Heib <mheib@redhat.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250225112852.2507709-1-mheib@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d52da23b6 ]
Recently a bug was discovered where the server had entered TCP_ESTABLISHED
state, but the upper layers were not notified.
The same 5-tuple packet may be processed by different CPUSs, so two
CPUs may receive different ack packets at the same time when the
state is TCP_NEW_SYN_RECV.
In that case, req->ts_recent in tcp_check_req may be changed concurrently,
which will probably cause the newsk's ts_recent to be incorrectly large.
So that tcp_validate_incoming will fail. At this point, newsk will not be
able to enter the TCP_ESTABLISHED.
cpu1 cpu2
tcp_check_req
tcp_check_req
req->ts_recent = rcv_tsval = t1
req->ts_recent = rcv_tsval = t2
syn_recv_sock
tcp_sk(child)->rx_opt.ts_recent = req->ts_recent = t2 // t1 < t2
tcp_child_process
tcp_rcv_state_process
tcp_validate_incoming
tcp_paws_check
if ((s32)(rx_opt->ts_recent - rx_opt->rcv_tsval) <= paws_win)
// t2 - t1 > paws_win, failed
tcp_v4_do_rcv
tcp_rcv_state_process
// TCP_ESTABLISHED
The cpu2's skb or a newly received skb will call tcp_v4_do_rcv to get
the newsk into the TCP_ESTABLISHED state, but at this point it is no
longer possible to notify the upper layer application. A notification
mechanism could be added here, but the fix is more complex, so the
current fix is used.
In tcp_check_req, req->ts_recent is used to assign a value to
tcp_sk(child)->rx_opt.ts_recent, so removing the change in req->ts_recent
and changing tcp_sk(child)->rx_opt.ts_recent directly after owning the
req fixes this bug.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c07be96d8 ]
As part of switchdev environment setup, uplink VSI is configured as
default for both Tx and Rx. Default Rx VSI is also used by promiscuous
mode. If promisc mode is enabled and an attempt to enter switchdev mode
is made, the setup will fail because Rx VSI is already configured as
default (rule exists).
Reproducer:
devlink dev eswitch set $PF1_PCI mode switchdev
ip l s $PF1 up
ip l s $PF1 promisc on
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
In switchdev setup, use ice_set_dflt_vsi() instead of plain
ice_cfg_dflt_vsi(), which avoids repeating setting default VSI for Rx if
it's already configured.
Fixes: 50d62022f4 ("ice: default Tx rule instead of to queue")
Reported-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Closes: https://lore.kernel.org/intel-wired-lan/PH0PR11MB50138B635F2E5CEB7075325D961F2@PH0PR11MB5013.namprd11.prod.outlook.com
Reviewed-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79990cf5e7 ]
If ice_ena_vfs() fails after calling ice_create_vf_entries(), it frees
all VFs without removing them from snapshot PF-VF mailbox list, leading
to list corruption.
Reproducer:
devlink dev eswitch set $PF1_PCI mode switchdev
ip l s $PF1 up
ip l s $PF1 promisc on
sleep 1
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
Trace (minimized):
list_add corruption. next->prev should be prev (ffff8882e241c6f0), but was 0000000000000000. (next=ffff888455da1330).
kernel BUG at lib/list_debug.c:29!
RIP: 0010:__list_add_valid_or_report+0xa6/0x100
ice_mbx_init_vf_info+0xa7/0x180 [ice]
ice_initialize_vf_entry+0x1fa/0x250 [ice]
ice_sriov_configure+0x8d7/0x1520 [ice]
? __percpu_ref_switch_mode+0x1b1/0x5d0
? __pfx_ice_sriov_configure+0x10/0x10 [ice]
Sometimes a KASAN report can be seen instead with a similar stack trace:
BUG: KASAN: use-after-free in __list_add_valid_or_report+0xf1/0x100
VFs are added to this list in ice_mbx_init_vf_info(), but only removed
in ice_free_vfs(). Move the removing to ice_free_vf_entries(), which is
also being called in other places where VFs are being removed (including
ice_free_vfs() itself).
Fixes: 8cd8a6b17d ("ice: move VF overflow message count into struct ice_mbx_vf_info")
Reported-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Closes: https://lore.kernel.org/intel-wired-lan/PH0PR11MB50138B635F2E5CEB7075325D961F2@PH0PR11MB5013.namprd11.prod.outlook.com
Reviewed-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59f4d59b25 ]
E830 adds hardware support to prevent the VF from overflowing the PF
mailbox with VIRTCHNL messages. E830 will use the hardware feature
(ICE_F_MBX_LIMIT) instead of the software solution ice_is_malicious_vf().
To prevent a VF from overflowing the PF, the PF sets the number of
messages per VF that can be in the PF's mailbox queue
(ICE_MBX_OVERFLOW_WATERMARK). When the PF processes a message from a VF,
the PF decrements the per VF message count using the E830_MBX_VF_DEC_TRIG
register.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 79990cf5e7 ("ice: Fix deinitializing VF in error path")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18912c5206 ]
Currently, we report -ETOOSMALL (err) only on the first iteration
(!sent). When we get put_cmsg error after a bunch of successful
put_cmsg calls, we don't signal the error at all. This might be
confusing on the userspace side which will see truncated CMSGs
but no MSG_CTRUNC signal.
Consider the following case:
- sizeof(struct cmsghdr) = 16
- sizeof(struct dmabuf_cmsg) = 24
- total cmsg size (CMSG_LEN) = 40 (16+24)
When calling recvmsg with msg_controllen=60, the userspace
will receive two(!) dmabuf_cmsg(s), the first one will
be a valid one and the second one will be silently truncated. There is no
easy way to discover the truncation besides doing something like
"cm->cmsg_len != CMSG_LEN(sizeof(dmabuf_cmsg))".
Introduce new put_devmem_cmsg wrapper that reports an error instead
of doing the truncation. Mina suggests that it's the intended way
this API should work.
Note that we might now report MSG_CTRUNC when the users (incorrectly)
call us with msg_control == NULL.
Fixes: 8f0b3cc9a4 ("tcp: RX path for devmem TCP")
Reviewed-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250224174401.3582695-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e7c6779e3 ]
ASUS VivoBook 15 with SSID 1043:1460 took an incorrect quirk via the
pin pattern matching for ASUS (ALC256_FIXUP_ASUS_MIC), resulting in
the two built-in mic pins (0x13 and 0x1b). This had worked without
problems casually in the past because the right pin (0x1b) was picked
up as the primary device. But since we fixed the pin enumeration for
other bugs, the bogus one (0x13) is picked up as the primary device,
hence the bug surfaced now.
For addressing the regression, this patch explicitly specifies the
quirk entry with ALC256_FIXUP_ASUS_MIC_NO_PRESENCE, which sets up only
the headset mic pin.
Fixes: 3b4309546b ("ALSA: hda: Fix headset detection failure due to unstable sort")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219807
Link: https://patch.msgid.link/20250225154540.13543-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 769c1b7929 ]
When SPI is used for control, the driver must hold the SPI bus lock
while issuing the sequence of writes to perform a soft reset.
>From the time the driver writes the SYSTEM_RESET command until the
driver does a write to terminate the reset, there must not be any
activity on the SPI bus lines. If there is any SPI activity during the
soft-reset, another soft-reset will be triggered. The state of the SPI
chip select is irrelevant.
A repeated soft-reset does not in itself cause any problems, and it is
not an infinite loop. The problem is a race between these resets and
the driver polling for boot completion. There is a time window between
soft resets where the driver could read HALO_STATE as 2 (fully booted)
while the chip is actually soft-resetting. Although this window is
small, it is long enough that it is possible to hit it in normal
operation.
To prevent this race and ensure the chip really is fully booted, the
driver calls spi_bus_lock() to prevent other activity while resetting.
It then issues the SYSTEM_RESET mailbox command. After allowing
sufficient time for reset to take effect, the driver issues a PING
mailbox command, which will force completion of the full soft-reset
sequence. The SPI bus lock can then be released. The mailbox is
checked for any boot or wakeup response from the firmware, before the
value in HALO_STATE will be trusted.
This does not affect SoundWire or I2C control.
Fixes: 8a731fd37f ("ASoC: cs35l56: Move utility functions to shared file")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250225131843.113752-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe08b7d508 ]
Change calls to async regmap write functions to use the normal
blocking writes so that the cs35l56 driver can use spi_bus_lock() to
gain exclusive access to the SPI bus.
As this is part of a fix, it makes only the minimal change to swap the
functions to the blocking equivalents. There's no need to risk
reworking the buffer allocation logic that is now partially redundant.
The async writes are a 12-year-old workaround for inefficiency of
synchronous writes in the SPI subsystem. The SPI subsystem has since
been changed to avoid the overheads, so this workaround should not be
necessary.
The cs35l56 driver needs to use spi_bus_lock() prevent bus activity
while it is soft-resetting the cs35l56. But spi_bus_lock() is
incompatible with spi_async() calls, which will fail with -EBUSY.
Fixes: 8a731fd37f ("ASoC: cs35l56: Move utility functions to shared file")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250225131843.113752-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bd566703e ]
OA exponent value of 0 is a valid value for periodic reports. Allow user
to pass 0 for the OA sampling interval since it gets converted to 2 gt
clock ticks.
v2: Update the check in xe_oa_stream_init as well (Ashutosh)
v3: Fix mi-rpc failure by setting default exponent to -1 (CI)
v4: Add the Fixes tag
Fixes: b6fd51c621 ("drm/xe/oa/uapi: Define and parse OA stream properties")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250221213352.1712932-1-umesh.nerlige.ramappa@intel.com
(cherry picked from commit 30341f0b8e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85d3f9e84e ]
Whereas all properties can be specified during OA stream open, when the OA
stream is reconfigured only the config_id and syncs can be specified.
v2: Use separate function table for reconfig case (Jonathan)
Change bool function args to enum (Matt B)
v3: s/xe_oa_set_property_funcs/xe_oa_set_property_funcs_open/ (Jonathan)
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Suggested-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241022200352.1192560-8-ashutosh.dixit@intel.com
Stable-dep-of: 5bd566703e ("drm/xe/oa: Allow oa_exponent value of 0")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9920c8b88c ]
In addition to stream open, add xe_sync support to the OA config ioctl,
where it is even more useful. This allows e.g. Mesa to replay a workload
repeatedly on the GPU, each time with a different OA configuration, while
precisely controlling (at batch buffer granularity) the workload segment
for which a particular OA configuration is active, without introducing
stalls in the userspace pipeline.
v2: Emit OA config even when config id is same as previous, to ensure
consistent sync behavior (Jose)
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241022200352.1192560-7-ashutosh.dixit@intel.com
Stable-dep-of: 5bd566703e ("drm/xe/oa: Allow oa_exponent value of 0")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc4e6994d5 ]
No code changes, only code movement so that functions used during stream
open can be reused for the stream reconfiguration
ioctl (DRM_XE_OBSERVATION_IOCTL_CONFIG).
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241022200352.1192560-6-ashutosh.dixit@intel.com
Stable-dep-of: 5bd566703e ("drm/xe/oa: Allow oa_exponent value of 0")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 343dd246fd ]
Introduce 'struct xe_oa_fence' which includes the dma_fence used to signal
output fences in the xe_sync array. The fences are signaled
asynchronously. When there are no output fences to signal, the OA
configuration wait is synchronously re-introduced into the ioctl.
v2: Don't wait in the work, use callback + delayed work (Matt B)
Use a single, not a per-fence spinlock (Matt Brost)
v3: Move ofence alloc before job submission (Matt)
Assert, don't fail, from dma_fence_add_callback (Matt)
Additional dma_fence_get for dma_fence_wait (Matt)
Change dma_fence_wait to non-interruptible (Matt)
v4: Introduce last_fence to prevent uaf if stream is closed with
pending OA config jobs
v5: Remove oa_fence_lock, move spinlock back into xe_oa_fence to
prevent uaf
Suggested-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241022200352.1192560-5-ashutosh.dixit@intel.com
Stable-dep-of: 5bd566703e ("drm/xe/oa: Allow oa_exponent value of 0")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de2c211868 ]
We found an issue when using bpf_redirect with ipvs NAT mode after
commit ff70202b2d ("dev_forward_skb: do not scrub skb mark within
the same name space"). Particularly, we use bpf_redirect to return
the skb directly back to the netif it comes from, i.e., xnet is
false in skb_scrub_packet(), and then ipvs_property is preserved
and SNAT is skipped in the rx path.
ipvs_property has been already cleared when netns is changed in
commit 2b5ec1a5f9 ("netfilter/ipvs: clear ipvs_property flag when
SKB net namespace changed"). This patch just clears it in spite of
netns.
Fixes: 2b5ec1a5f9 ("netfilter/ipvs: clear ipvs_property flag when SKB net namespace changed")
Signed-off-by: Philo Lu <lulie@linux.alibaba.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Link: https://patch.msgid.link/20250222033518.126087-1-lulie@linux.alibaba.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0da83ab025 ]
If stream names of DAI driver are duplicated there'll be warnings when
machine driver tries to add widgets on a route:
[ 8.831335] fsl-asoc-card sound-wm8960: ASoC: sink widget CPU-Playback overwritten
[ 8.839917] fsl-asoc-card sound-wm8960: ASoC: source widget CPU-Capture overwritten
Use different stream names to avoid such warnings.
DAI names in AUDMIX are also updated accordingly.
Fixes: 15c9583904 ("ASoC: fsl_sai: Add separate DAI for transmitter and receiver")
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://patch.msgid.link/20250217010437.258621-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b0c02f9b8 ]
The ES8328 codec driver, which is also used for the ES8388 chip that
appears to have an identical register map, claims that the output can
either take the route from DAC->Mixer->Output or through DAC->Output
directly. To the best of what I could find, this is not true, and
creates problems.
Without DACCONTROL17 bit index 7 set for the left channel, as well as
DACCONTROL20 bit index 7 set for the right channel, I cannot get any
analog audio out on Left Out 2 and Right Out 2 respectively, despite the
DAPM routes claiming that this should be possible. Furthermore, the same
is the case for Left Out 1 and Right Out 1, showing that those two don't
have a direct route from DAC to output bypassing the mixer either.
Those control bits toggle whether the DACs are fed (stale bread?) into
their respective mixers. If one "unmutes" the mixer controls in
alsamixer, then sure, the audio output works, but if it doesn't work
without the mixer being fed the DAC input then evidently it's not a
direct output from the DAC.
ES8328/ES8388 are seemingly not alone in this. ES8323, which uses a
separate driver for what appears to be a very similar register map,
simply flips those two bits on in its probe function, and then pretends
there is no power management whatsoever for the individual controls.
Fair enough.
My theory as to why nobody has noticed this up to this point is that
everyone just assumes it's their fault when they had to unmute an
additional control in ALSA.
Fix this in the es8328 driver by removing the erroneous direct route,
then get rid of the playback switch controls and have those bits tied to
the mixer's widget instead, which until now had no register to play
with.
Fixes: 567e4f9892 ("ASoC: add es8328 codec driver")
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://patch.msgid.link/20250222-es8328-route-bludgeoning-v1-1-99bfb7fb22d9@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f15176b8b6 ]
When the kernel is compiled without LED framework support the
rtl8366rb fails to build like this:
rtl8366rb.o: in function `rtl8366rb_setup_led':
rtl8366rb.c:953:(.text.unlikely.rtl8366rb_setup_led+0xe8):
undefined reference to `led_init_default_state_get'
rtl8366rb.c:980:(.text.unlikely.rtl8366rb_setup_led+0x240):
undefined reference to `devm_led_classdev_register_ext'
As this is constantly coming up in different randconfig builds,
bite the bullet and create a separate file for the offending
code, split out a header with all stuff needed both in the
core driver and the leds code.
Add a new bool Kconfig option for the LED compile target, such
that it depends on LEDS_CLASS=y || LEDS_CLASS=RTL8366RB
which make LED support always available when LEDS_CLASS is
compiled into the kernel and enforce that if the LEDS_CLASS
is a module, then the RTL8366RB driver needs to be a module
as well so that modprobe can resolve the dependencies.
Fixes: 32d6170054 ("net: dsa: realtek: add LED drivers for rtl8366rb")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202502070525.xMUImayb-lkp@intel.com/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa52f15c74 ]
Stats calculations involve a RMW to add the stat update to the existing
value. This is currently not protected by any synchronization mechanism,
so data races are possible. Add a spinlock to protect the update. The
reader side could be protected using u64_stats, but we would still need
a spinlock for the update side anyway. And we always do an update
immediately before reading the stats anyway.
Fixes: 89e5785fc8 ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20250220162950.95941-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c30d6eedd ]
Use ip4h_dscp() to get the DSCP from the IPv4 header, then convert the
dscp_t value to __u8 with inet_dscp_to_dsfield().
Then, when we'll convert .flowi4_tos to dscp_t, we'll just have to drop
the inet_dscp_to_dsfield() call.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/f48335504a05b3587e0081a9b4511e0761571ca5.1730292157.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 27843ce6ba ("ipvlan: ensure network headers are in skb linear part")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e863e5db6 ]
Pass a dscp_t variable to ip_route_input(), instead of a plain u8, to
prevent accidental setting of ECN bits in ->flowi4_tos.
Callers of ip_route_input() to consider are:
* input_action_end_dx4_finish() and input_action_end_dt4() in
net/ipv6/seg6_local.c. These functions set the tos parameter to 0,
which is already a valid dscp_t value, so they don't need to be
adjusted for the new prototype.
* icmp_route_lookup(), which already has a dscp_t variable to pass as
parameter. We just need to remove the inet_dscp_to_dsfield()
conversion.
* br_nf_pre_routing_finish(), ip_options_rcv_srr() and ip4ip6_err(),
which get the DSCP directly from IPv4 headers. Define a helper to
read the .tos field of struct iphdr as dscp_t, so that these
function don't have to do the conversion manually.
While there, declare *iph as const in br_nf_pre_routing_finish(),
declare its local variables in reverse-christmas-tree order and move
the "err = ip_route_input()" assignment out of the conditional to avoid
checkpatch warning.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/e9d40781d64d3d69f4c79ac8a008b8d67a033e8d.1727807926.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 27843ce6ba ("ipvlan: ensure network headers are in skb linear part")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 913c83a610 ]
Pass a dscp_t variable to icmp_route_lookup(), instead of a plain u8,
to prevent accidental setting of ECN bits in ->flowi4_tos. Rename that
variable ("tos" -> "dscp") to make the intent clear.
While there, reorganise the function parameters to fill up horizontal
space.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/294fead85c6035bcdc5fcf9a6bb4ce8798c45ba1.1727807926.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 27843ce6ba ("ipvlan: ensure network headers are in skb linear part")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c180188ec0 ]
Commit 7acf8a1e8a ("Replace 2 jiffies with sysctl netdev_budget_usecs
to enable softirq tuning") added a possibility to set
net_hotdata.netdev_budget_usecs, but added no lower bound checking.
Commit a4837980fd ("net: revert default NAPI poll timeout to 2 jiffies")
made the *initial* value HZ-dependent, so the initial value is at least
2 jiffies even for lower HZ values (2 ms for 1000 Hz, 8ms for 250 Hz, 20
ms for 100 Hz).
But a user still can set improper values by a sysctl. Set .extra1
(the lower bound) for net_hotdata.netdev_budget_usecs to the same value
as in the latter commit. That is to 2 jiffies.
Fixes: a4837980fd ("net: revert default NAPI poll timeout to 2 jiffies")
Fixes: 7acf8a1e8a ("Replace 2 jiffies with sysctl netdev_budget_usecs to enable softirq tuning")
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Dmitry Yakunin <zeil@yandex-team.ru>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Link: https://patch.msgid.link/20250220110752.137639-1-jirislaby@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e4427f8f5 ]
After commit 22600596b6 ("ipv4: give an IPv4 dev to blackhole_netdev")
IPv4 neighbors can be constructed on the blackhole net device, but they
are constructed with an output function (neigh_direct_output()) that
simply calls dev_queue_xmit(). The latter will transmit packets via
'skb->dev' which might not be the blackhole net device if dst_dev_put()
switched 'dst->dev' to the blackhole net device while another CPU was
using the dst entry in ip_output(), but after it already initialized
'skb->dev' from 'dst->dev'.
Specifically, the following can happen:
CPU1 CPU2
udp_sendmsg(sk1) udp_sendmsg(sk2)
udp_send_skb() [...]
ip_output()
skb->dev = skb_dst(skb)->dev
dst_dev_put()
dst->dev = blackhole_netdev
ip_finish_output2()
resolves neigh on dst->dev
neigh_output()
neigh_direct_output()
dev_queue_xmit()
This will result in IPv4 packets being sent without an Ethernet header
via a valid net device:
tcpdump: verbose output suppressed, use -v[v]... for full protocol decode
listening on enp9s0, link-type EN10MB (Ethernet), snapshot length 262144 bytes
22:07:02.329668 20:00:40:11:18:fb > 45:00:00:44:f4:94, ethertype Unknown
(0x58c6), length 68:
0x0000: 8dda 74ca f1ae ca6c ca6c 0098 969c 0400 ..t....l.l......
0x0010: 0000 4730 3f18 6800 0000 0000 0000 9971 ..G0?.h........q
0x0020: c4c9 9055 a157 0a70 9ead bf83 38ca ab38 ...U.W.p....8..8
0x0030: 8add ab96 e052 .....R
Fix by making sure that neighbors are constructed on top of the
blackhole net device with an output function that simply consumes the
packets, in a similar fashion to dst_discard_out() and
blackhole_netdev_xmit().
Fixes: 8d7017fd62 ("blackhole_netdev: use blackhole_netdev to invalidate dst entries")
Fixes: 22600596b6 ("ipv4: give an IPv4 dev to blackhole_netdev")
Reported-by: Florian Meister <fmei@sfs.com>
Closes: https://lore.kernel.org/netdev/20250210084931.23a5c2e4@hermes.local/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250220072559.782296-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
