commit f7061ffb44 upstream.
The pinctrl pull up/down register on exynos4210 is 2-bit wide for each
pin and it accepts only values of 0, 1 and 3. The pins sd4-bus-width8
were configured with value of 4. The driver does not validate the value
so this overflow effectively set a bit 1 in adjacent pins thus
configuring them to pull down.
The author's intention was probably to set drive strength of 4x. All
other bus-widths pins are configured with pull up and drive strength of
4x. Fix this one with same pattern.
Fixes: 87711d8c7c ("ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[bwh: Backported to 3.16: use literal constant]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7798bf2140 upstream.
On faulting sigreturn we do get SIGSEGV, all right, but anything
we'd put into pt_regs could end up in the coredump. And since
__copy_from_user() never zeroed on arc, we'd better bugger off
on its failure without copying random uninitialized bits of
kernel stack into pt_regs...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: Backported to 3.16:
- Adjust context
- Don't change the single return statement]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4e800c0359 upstream.
Pages clear buffers after ext4 delayed block allocation failed,
However, it does not clean its pte_dirty flag.
if the pages unmap ,in cording to the pte_dirty ,
unmap_page_range may try to call __set_page_dirty,
which may lead to the bugon at
mpage_prepare_extent_to_map:head = page_buffers(page);.
This patch just call clear_page_dirty_for_io to clean pte_dirty
at mpage_release_unused_pages for pages mmaped.
Steps to reproduce the bug:
（1） mmap a file in ext4
addr = (char *)mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_SHARED,
fd, 0);
memset(addr, 'i', 4096);
（2） return EIO at
ext4_writepages->mpage_map_and_submit_extent->mpage_map_one_extent
which causes this log message to be print:
ext4_msg(sb, KERN_CRIT,
"Delayed block allocation failed for "
"inode %lu at logical offset %llu with"
" max blocks %u with error %d",
inode->i_ino,
(unsigned long long)map->m_lblk,
(unsigned)map->m_len, -err);
(3）Unmap the addr cause warning at
__set_page_dirty:WARN_ON_ONCE(warn && !PageUptodate(page));
(4) wait for a minute,then bugon happen.
Signed-off-by: wangguang <wangguang03@zte.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f10e06b744 upstream.
If pg_init_retries is set and a request is queued against a multipath
device with all underlying block device request_queues in the "dying"
state then an infinite loop is triggered because activate_path() never
succeeds and hence never calls pg_init_done().
This change avoids that device removal triggers an infinite loop by
failing the activate_path() which causes the "dying" path to be failed.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3b785fbcf8 upstream.
This avoids that new requests are queued while __dm_destroy() is in
progress.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[js: use md->queue instead of non-present helper]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 541d48f05f upstream.
oss.sgi.com is going away, move contact details over to vger.
Signed-off-by: Dave Chinner <david@fromorbit.com>
[bwh: Backported to 3.16: Also update the git URL, done upstream in commit
9f273c24ec "MAINTAINERS: add/fix git URLs for various subsystems"]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 919ab2524c upstream.
The musb driver calls into this phy driver to disable/enable squelch
detection. This function was introduced in 24fe86a617 ("phy: sun4i-usb:
Add a sunxi specific function for setting squelch-detect"). This
function in turn calls sun4i_usb_phy_write, which uses a mutex to
guard the common access register. Unfortunately musb does this
in atomic context, which results in the following warning with lock
debugging enabled:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:97
in_atomic(): 1, irqs_disabled(): 128, pid: 96, name: kworker/0:2
CPU: 0 PID: 96 Comm: kworker/0:2 Not tainted 4.8.0-rc4-00181-gd502f8ad1c3e #13
Hardware name: Allwinner sun8i Family
Workqueue: events musb_deassert_reset
[<c010bc01>] (unwind_backtrace) from [<c0109237>] (show_stack+0xb/0xc)
[<c0109237>] (show_stack) from [<c02a669b>] (dump_stack+0x67/0x74)
[<c02a669b>] (dump_stack) from [<c05d68c9>] (mutex_lock+0x15/0x2c)
[<c05d68c9>] (mutex_lock) from [<c02c3589>] (sun4i_usb_phy_write+0x39/0xec)
[<c02c3589>] (sun4i_usb_phy_write) from [<c03e6327>] (musb_port_reset+0xfb/0x184)
[<c03e6327>] (musb_port_reset) from [<c03e4917>] (musb_deassert_reset+0x1f/0x2c)
[<c03e4917>] (musb_deassert_reset) from [<c012ecb5>] (process_one_work+0x129/0x2b8)
[<c012ecb5>] (process_one_work) from [<c012f5e3>] (worker_thread+0xf3/0x424)
[<c012f5e3>] (worker_thread) from [<c0132dbd>] (kthread+0xa1/0xb8)
[<c0132dbd>] (kthread) from [<c0105f31>] (ret_from_fork+0x11/0x20)
Since the register access is mmio, we can use a spinlock to guard this
specific access, rather than the mutex that guards the entire phy.
Fixes: ba4bdc9e1d ("PHY: sunxi: Add driver for sunxi usb phy")
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ca26475bf0 upstream.
The commit 9bf448c66d ("ARM: pxa: use generic gpio operation instead of
gpio register") from Oct 17, 2011, leads to the following static checker
warning:
arch/arm/mach-pxa/spitz_pm.c:172 spitz_charger_wakeup()
warn: double left shift '!gpio_get_value(SPITZ_GPIO_KEY_INT)
<< (1 << ((SPITZ_GPIO_KEY_INT) & 31))'
As Dan reported, the value is shifted three times :
- once by gpio_get_value(), which returns either 0 or BIT(gpio)
- once by the shift operation '<<'
- a last time by GPIO_bit(gpio) which is BIT(gpio)
Therefore the calculation lead to a chained or operator of :
- (1 << gpio) << (1 << gpio) = (2^gpio)^gpio = 2 ^ (gpio * gpio)
It is be sheer luck the former statement works, only because each gpio
used is strictly smaller than 6, and therefore 2^(gpio^2) never
overflows a 32 bits value, and because it is used as a boolean value to
check a gpio activation.
As the xxx_charger_wakeup() functions are used as a true/false detection
mechanism, take that opportunity to change their prototypes from integer
return value to boolean one.
Fixes: 9bf448c66d ("ARM: pxa: use generic gpio operation instead of
gpio register")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e895cdce68 upstream.
In commit f02db315b8 ("ipv4: IP_TOS and IP_TTL can be specified as
ancillary data") Francesco added IP_TOS values specified as integer.
However, kernel sends to userspace (at recvmsg() time) an IP_TOS value
in a single byte, when IP_RECVTOS is set on the socket.
It can be very useful to reflect all ancillary options as given by the
kernel in a subsequent sendmsg(), instead of aborting the sendmsg() with
EINVAL after Francesco patch.
So this patch extends IP_TOS ancillary to accept an u8, so that an UDP
server can simply reuse same ancillary block without having to mangle
it.
Jesper can then augment
https://github.com/netoptimizer/network-testing/blob/master/src/udp_example02.c
to add TOS reflection ;)
Fixes: f02db315b8 ("ipv4: IP_TOS and IP_TTL can be specified as ancillary data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Francesco Fusco <ffusco@redhat.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d771fdf941 upstream.
The ramoops buffer may be mapped as either I/O memory or uncached
memory. On ARM64, this results in a device-type (strongly-ordered)
mapping. Since unnaligned accesses to device-type memory will
generate an alignment fault (regardless of whether or not strict
alignment checking is enabled), it is not safe to use memcpy().
memcpy_fromio() is guaranteed to only use aligned accesses, so use
that instead.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Reviewed-by: Puneet Kumar <puneetster@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7e75678d23 upstream.
persistent_ram_update uses vmap / iomap based on whether the buffer is in
memory region or reserved region. However, both map it as non-cacheable
memory. For armv8 specifically, non-cacheable mapping requests use a
memory type that has to be accessed aligned to the request size. memcpy()
doesn't guarantee that.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d5a9bf0b38 upstream.
I have here a FPGA behind PCIe which exports SRAM which I use for
pstore. Now it seems that the FPGA no longer supports cmpxchg based
updates and writes back 0xff…ff and returns the same. This leads to
crash during crash rendering pstore useless.
Since I doubt that there is much benefit from using cmpxchg() here, I am
dropping this atomic access and use the spinlock based version.
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Rabin Vincent <rabinv@axis.com>
Tested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
[kees: remove "_locked" suffix since it's the only option now]
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 93e3b4e663 upstream.
Now, ext4_do_update_inode() clears high 16-bit fields of uid/gid
of deleted and evicted inode to fix up interoperability with old
kernels. However, it checks only i_dtime of an inode to determine
whether the inode was deleted and evicted, and this is very risky,
because i_dtime can be used for the pointer maintaining orphan inode
list, too. We need to further check whether the i_dtime is being
used for the orphan inode list even if the i_dtime is not NULL.
We found that high 16-bit fields of uid/gid of inode are unintentionally
and permanently cleared when the inode truncation is just triggered,
but not finished, and the inode metadata, whose high uid/gid bits are
cleared, is written on disk, and the sudden power-off follows that
in order.
Signed-off-by: Daeho Jeong <daeho.jeong@samsung.com>
Signed-off-by: Hobin Woo <hobin.woo@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 24b923f073 upstream.
This device uses GPIOs: 28 to switch between analog and
digital modes: on digital mode, it should be set to 1.
The code that sets it on analog mode is OK, but it misses
the logic that sets it on digital mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1871d718a9 upstream.
The cx231xx_set_agc_analog_digital_mux_select() callers
expect it to return 0 or an error. Returning a positive value
makes the first attempt to switch between analog/digital to fail.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 505a0ea706 upstream.
With the current settings, only one channel locks properly.
That's likely because, when this driver was written, Brazil
were still using experimental transmissions.
Change it to reproduce the settings used by the newer drivers.
That makes it lock on other channels.
Tested with both PixelView SBTVD Hybrid (cx231xx-based) and
C3Tech Digital Duo HDTV/SDTV (em28xx-based) devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit dafb65fb98 upstream.
On this frontend, it takes a while to start output normal
TS data. That only happens on state S9. On S8, the TS output
is enabled, but it is not reliable enough.
However, the zigzag loop is too fast to let it sync.
As, on practical tests, the zigzag software loop doesn't
seem to be helping, but just slowing down the tuning, let's
switch to hardware algorithm, as the tuners used on such
devices are capable of work with frequency drifts without
any help from software.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0733424c9b upstream.
Exported pwm channels aren't removed before the pwmchip and are
leaked. This results in invalid sysfs files. This fix removes
all exported pwm channels before chip removal.
Signed-off-by: David Hsu <davidhsu@google.com>
Fixes: 76abbdde2d ("pwm: Add sysfs interface")
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0c9d349153 upstream.
Some RTL8821AE devices sold in Great Britain have the country code of
0x25 encoded in their EEPROM. This value is not tested in the routine
that establishes the regulatory info for the chip. The fix is to set
this code to have the same capabilities as the EU countries. In addition,
the channels allowed for COUNTRY_CODE_ETSI were more properly suited
for China and Israel, not the EU. This problem has also been fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 02b5fffbe9 upstream.
Driver rtlwifi maintains its own regulatory information, The Chrome Autotest
(https://www.chromium.org/chromium-os/testing/autotest-user-doc)
showed some errors. This patch adds the necessary information for rtlwifi.
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ee26c013cd upstream.
Without this patch irq_domain_disassociate() cannot properly release the
interrupt. In fact, irq_map_generic_chip() checks a bit on 'gc->installed'
but said bit is never cleared, only set.
Commit 088f40b7b0 ("genirq: Generic chip: Add linear irq domain support")
added irq_map_generic_chip() function and also stated "This lacks a removal
function for now".
This commit provides an implementation of an unmap function that can be
called by irq_domain_disassociate().
[ tglx: Made the function static and removed the export as we have neither
a prototype nor a modular user. ]
Fixes: 088f40b7b0 ("genirq: Generic chip: Add linear irq domain support")
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mason <slash.tmp@free.fr>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/579F5C5A.2070507@laposte.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bwh: Backported to 3.16: open-code irq_domain_get_irq_data(),
irq_domain_set_info()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 071133a209 upstream.
The value for the second channel in _ENUM_DOUBLE (double channel) MUXs
is not correctly updated, due to using the wrong bit shift.
Use the correct bit shift, so both channels toggle together.
Fixes: 3727b49684 (ASoC: dapm: Consolidate MUXs and value MUXs)
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 432746f8e0 upstream.
When we call symbol__fixup_duplicate() we use algorithms to pick the
"best" symbols for cases where there are various functions/aliases to an
address, and those check zero size symbols, which, before calling
symbol__fixup_end() are _all_ symbols in a just parsed kallsyms file.
So first fixup the end, then fixup the duplicates.
Found while trying to figure out why 'perf test vmlinux' failed, see the
output of 'perf test -v vmlinux' to see cases where the symbols picked
as best for vmlinux don't match the ones picked for kallsyms.
Cc: Anton Blanchard <anton@samba.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: 694bf407b0 ("perf symbols: Add some heuristics for choosing the best duplicate symbol")
Link: http://lkml.kernel.org/n/tip-rxqvdgr0mqjdxee0kf8i2ufn@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3a402a7095 upstream.
When TIF_SINGLESTEP is set for a task, the single-step state machine is
enabled and we must take care not to reset it to the active-not-pending
state if it is already in the active-pending state.
Unfortunately, that's exactly what user_enable_single_step does, by
unconditionally setting the SS bit in the SPSR for the current task.
This causes failures in the GDB testsuite, where GDB ends up missing
expected step traps if the instruction being stepped generates another
trap, e.g. PTRACE_EVENT_FORK from an SVC instruction.
This patch fixes the problem by preserving the current state of the
stepping state machine when TIF_SINGLESTEP is set on the current thread.
Reported-by: Yao Qi <yao.qi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e330b9a6bb upstream.
of_irq_get[_byname]() return 0 iff irq_create_of_mapping() call fails.
Returning both error code and 0 on failure is a sign of a misdesigned API,
it makes the failure check unnecessarily complex and error prone. We should
rely on the platform IRQ resource in this case, not return 0, especially
as 0 can be a valid IRQ resource too...
Fixes: aff008ad81 ("platform_get_irq: Revert to platform_get_resource if of_irq_get fails")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4d31a2588a upstream.
The variable i contains a total number of resources (including
IORESOURCE_IRQ). However, we want the dmem_region_start to point
after the last resource of type IORESOURCE_MEM. The original behaviour
leads (very likely) to skipping several UIO mapping regions and makes
them useless. Fix this by computing dmem_region_start from the uiomem
which points to the last used UIO mapping.
Fixes: 0a0c3b5a24 ("Add new uio device for dynamic memory allocation")
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 95a8d19f28 upstream.
In case nf_conntrack_tuple_taken did not find a conflicting entry
check that all entries in this hash slot were tested and restart
in case an entry was moved to another chain.
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: ea781f197d ("netfilter: nf_conntrack: use SLAB_DESTROY_BY_RCU and get rid of call_rcu()")
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[bwh: Backported to 3.16:
- Adjust context
- Use NF_CT_STAT_INC(), not the _ATOMIC variant, since we disable BHs]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9a0a5c4cb1 upstream.
Since we keep shadow copies of which interrupt sources are enabled
through the intrl2_*_mask_{set,clear} macros, make sure that the
ordering in which we do these two operations: update the copy, then
unmask the register is correct.
This is not currently a problem because we actually do not use them, but
we will in a subsequent patch optimizing register accesses, so better be
safe here.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8e2e031799 upstream.
Similar to the AR93xx and the AR94xx series, the AR95xx also have the same
quirk for the Bus Reset. It will lead to instant system reset if the
device is assigned via VFIO to a KVM VM. I've been able reproduce this
behavior with a MikroTik R11e-2HnD.
Fixes: c3e59ee4e7 ("PCI: Mark Atheros AR93xx to avoid bus reset")
Signed-off-by: Maik Broemme <mbroemme@libmpq.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 72b4f6a5e9 upstream.
On x86_32, when an interrupt happens from kernel space, SS and SP aren't
pushed and the existing stack is used. So pt_regs is effectively two
words shorter, and the previous stack pointer is normally the memory
after the shortened pt_regs, aka '®s->sp'.
But in the rare case where the interrupt hits right after the stack
pointer has been changed to point to an empty stack, like for example
when call_on_stack() is used, the address immediately after the
shortened pt_regs is no longer on the stack. In that case, instead of
'®s->sp', the previous stack pointer should be retrieved from the
beginning of the current stack page.
kernel_stack_pointer() wants to do that, but it forgets to dereference
the pointer. So instead of returning a pointer to the previous stack,
it returns a pointer to the beginning of the current stack.
Note that it's probably outside of kernel_stack_pointer()'s scope to be
switching stacks at all. The x86_64 version of this function doesn't do
it, and it would be better for the caller to do it if necessary. But
that's a patch for another day. This just fixes the original intent.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 0788aa6a23 ("x86: Prepare removal of previous_esp from i386 thread_info structure")
Link: http://lkml.kernel.org/r/472453d6e9f6a2d4ab16aaed4935f43117111566.1471535549.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2cf9a57811 upstream.
clk-divider uses clk_readl()/clk_writel() everywhere, except in
clk_divider_round_rate(), where plain readl() is used. Change this to
clk_readl(), as it makes a difference on powerpc.
Fixes: e6d5e7d90b ("clk-divider: Fix READ_ONLY when divider > 1")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit aceeffbb59 upstream.
This was lost with commit 2c55b750a8
("[SCSI] zfcp: Redesign of the debug tracing for SAN records.")
but is necessary for problem determination, e.g. to see the
currently active zone set during automatic port scan.
For the large GPN_FT response (4 pages), save space by not dumping
any empty residual entries.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 2c55b750a8 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.")
Reviewed-by: Alexey Ishchuk <aishchuk@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 94db3725f0 upstream.
commit 2c55b750a8
("[SCSI] zfcp: Redesign of the debug tracing for SAN records.")
started to add FC_CT_HDR_LEN which made zfcp dump random data
out of bounds for RSPN GS responses because u.rspn.rsp
is the largest and last field in the union of struct zfcp_fc_req.
Other request/response types only happened to stay within bounds
due to the padding of the union or
due to the trace capping of u.gspn.rsp to ZFCP_DBF_SAN_MAX_PAYLOAD.
Timestamp : ...
Area : SAN
Subarea : 00
Level : 1
Exception : -
CPU id : ..
Caller : ...
Record id : 2
Tag : fsscth2
Request id : 0x...
Destination ID : 0x00fffffc
Payload short : 01000000 fc020000 80020000 00000000
xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx <===
00000000 00000000 00000000 00000000
Payload length : 32 <===
struct zfcp_fc_req {
[0] struct zfcp_fsf_ct_els ct_els;
[56] struct scatterlist sg_req;
[96] struct scatterlist sg_rsp;
union {
struct {req; rsp;} adisc; SIZE: 28+28= 56
struct {req; rsp;} gid_pn; SIZE: 24+20= 44
struct {rspsg; req;} gpn_ft; SIZE: 40*4+20=180
struct {req; rsp;} gspn; SIZE: 20+273= 293
struct {req; rsp;} rspn; SIZE: 277+16= 293
[136] } u;
}
SIZE: 432
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 2c55b750a8 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.")
Reviewed-by: Alexey Ishchuk <aishchuk@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 771bf03537 upstream.
With commit 2c55b750a8
("[SCSI] zfcp: Redesign of the debug tracing for SAN records.")
we lost the N_Port-ID where an ELS response comes from.
With commit 7c7dc19681
("[SCSI] zfcp: Simplify handling of ct and els requests")
we lost the N_Port-ID where a CT response comes from.
It's especially useful if the request SAN trace record
with D_ID was already lost due to trace buffer wrap.
GS uses an open WKA port handle and ELS just a D_ID, and
only for ELS we could get D_ID from QTCB bottom via zfcp_fsf_req.
To cover both cases, add a new field to zfcp_fsf_ct_els
and fill it in on request to use in SAN response trace.
Strictly speaking the D_ID on SAN response is the FC frame's S_ID.
We don't need a field for the other end which is always us.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 2c55b750a8 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.")
Fixes: 7c7dc19681 ("[SCSI] zfcp: Simplify handling of ct and els requests")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7c964ffe58 upstream.
This information was lost with
commit a54ca0f62f
("[SCSI] zfcp: Redesign of the debug tracing for HBA records.")
but is required to debug e.g. invalid handle situations.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: a54ca0f62f ("[SCSI] zfcp: Redesign of the debug tracing for HBA records.")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d27a7cb919 upstream.
Since commit a54ca0f62f
("[SCSI] zfcp: Redesign of the debug tracing for HBA records.")
HBA records no longer contain WWPN, D_ID, or LUN
to reduce duplicate information which is already in REC records.
In contrast to "regular" target ports, we don't use recovery to open
WKA ports such as directory/nameserver, so we don't get REC records.
Therefore, introduce pseudo REC running records without any
actual recovery action but including D_ID of WKA port on open/close.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: a54ca0f62f ("[SCSI] zfcp: Redesign of the debug tracing for HBA records.")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0102a30a6f upstream.
bring back
commit d21e9daa63
("[SCSI] zfcp: Dont use 0 to indicate invalid LUN in rec trace")
which was lost with
commit ae0904f60f
("[SCSI] zfcp: Redesign of the debug tracing for recovery actions.")
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: ae0904f60f ("[SCSI] zfcp: Redesign of the debug tracing for recovery actions.")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 35f040df97 upstream.
While retaining the actual filtering according to trace level,
the following commits started to write such filtered records
with a hardcoded record level of 1 instead of the actual record level:
commit 250a1352b9
("[SCSI] zfcp: Redesign of the debug tracing for SCSI records.")
commit a54ca0f62f
("[SCSI] zfcp: Redesign of the debug tracing for HBA records.")
Now we can distinguish written records again for offline level filtering.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 250a1352b9 ("[SCSI] zfcp: Redesign of the debug tracing for SCSI records.")
Fixes: a54ca0f62f ("[SCSI] zfcp: Redesign of the debug tracing for HBA records.")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4eeaa4f3f1 upstream.
On a successful end of reopen port forced,
zfcp_erp_strategy_followup_success() re-uses the port erp_action
and the subsequent zfcp_erp_action_cleanup() now
sees ZFCP_ERP_SUCCEEDED with
erp_action->action==ZFCP_ERP_ACTION_REOPEN_PORT
instead of ZFCP_ERP_ACTION_REOPEN_PORT_FORCED
but must not perform zfcp_scsi_schedule_rport_register().
We can detect this because the fresh port reopen erp_action
is in its very first step ZFCP_ERP_STEP_UNINITIALIZED.
Otherwise this opens a time window with unblocked rport
(until the followup port reopen recovery would block it again).
If a scsi_cmnd timeout occurs during this time window
fc_timed_out() cannot work as desired and such command
would indeed time out and trigger scsi_eh. This prevents
a clean and timely path failover.
This should not happen if the path issue can be recovered
on FC transport layer such as path issues involving RSCNs.
Also, unnecessary and repeated DID_IMM_RETRY for pending and
undesired new requests occur because internally zfcp still
has its zfcp_port blocked.
As follow-on errors with scsi_eh, it can cause,
in the worst case, permanently lost paths due to one of:
sd <scsidev>: [<scsidisk>] Medium access timeout failure. Offlining disk!
sd <scsidev>: Device offlined - not ready after error recovery
For fix validation and to aid future debugging with other recoveries
we now also trace (un)blocking of rports.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 5767620c38 ("[SCSI] zfcp: Do not unblock rport from REOPEN_PORT_FORCED")
Fixes: a2fa0aede0 ("[SCSI] zfcp: Block FC transport rports early on errors")
Fixes: 5f852be9e1 ("[SCSI] zfcp: Fix deadlock between zfcp ERP and SCSI")
Fixes: 338151e066 ("[SCSI] zfcp: make use of fc_remote_port_delete when target port is unavailable")
Fixes: 3859f6a248 ("[PATCH] zfcp: add rports to enable scsi_add_device to work again")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 70369f8e15 upstream.
In the hardware data router case, introduced with kernel 3.2
commit 86a9668a8d ("[SCSI] zfcp: support for hardware data router")
the ELS/GS request&response length needs to be initialized
as in the chained SBAL case.
Otherwise, the FCP channel rejects ELS requests with
FSF_REQUEST_SIZE_TOO_LARGE.
Such ELS requests can be issued by user space through BSG / HBA API,
or zfcp itself uses ADISC ELS for remote port link test on RSCN.
The latter can cause a short path outage due to
unnecessary remote target port recovery because the always
failing ADISC cannot detect extremely short path interruptions
beyond the local FCP channel.
Below example is decoded with zfcpdbf from s390-tools:
Timestamp : ...
Area : SAN
Subarea : 00
Level : 1
Exception : -
CPU id : ..
Caller : zfcp_dbf_san_req+0408
Record id : 1
Tag : fssels1
Request id : 0x<reqid>
Destination ID : 0x00<target d_id>
Payload info : 52000000 00000000 <our wwpn > [ADISC]
<our wwnn > 00<s_id> 00000000
00000000 00000000 00000000 00000000
Timestamp : ...
Area : HBA
Subarea : 00
Level : 1
Exception : -
CPU id : ..
Caller : zfcp_dbf_hba_fsf_res+0740
Record id : 1
Tag : fs_ferr
Request id : 0x<reqid>
Request status : 0x00000010
FSF cmnd : 0x0000000b [FSF_QTCB_SEND_ELS]
FSF sequence no: 0x...
FSF issued : ...
FSF stat : 0x00000061 [FSF_REQUEST_SIZE_TOO_LARGE]
FSF stat qual : 00000000 00000000 00000000 00000000
Prot stat : 0x00000100
Prot stat qual : 00000000 00000000 00000000 00000000
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 86a9668a8d ("[SCSI] zfcp: support for hardware data router")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit bd77befa5b upstream.
For an NPIV-enabled FCP device, zfcp can erroneously show
"NPort (fabric via point-to-point)" instead of "NPIV VPORT"
for the port_type sysfs attribute of the corresponding
fc_host.
s390-tools that can be affected are dbginfo.sh and ziomon.
zfcp_fsf_exchange_config_evaluate() ignores
fsf_qtcb_bottom_config.connection_features indicating NPIV
and only sets fc_host_port_type to FC_PORTTYPE_NPORT if
fsf_qtcb_bottom_config.fc_topology is FSF_TOPO_FABRIC.
Only the independent zfcp_fsf_exchange_port_evaluate()
evaluates connection_features to overwrite fc_host_port_type
to FC_PORTTYPE_NPIV in case of NPIV.
Code was introduced with upstream kernel 2.6.30
commit 0282985da5
("[SCSI] zfcp: Report fc_host_port_type as NPIV").
This works during FCP device recovery (such as set online)
because it performs FSF_QTCB_EXCHANGE_CONFIG_DATA followed by
FSF_QTCB_EXCHANGE_PORT_DATA in sequence.
However, the zfcp-specific scsi host sysfs attributes
"requests", "megabytes", or "seconds_active" trigger only
zfcp_fsf_exchange_config_evaluate() resetting fc_host
port_type to FC_PORTTYPE_NPORT despite NPIV.
The zfcp-specific scsi host sysfs attribute "utilization"
triggers only zfcp_fsf_exchange_port_evaluate() correcting
the fc_host port_type again in case of NPIV.
Evaluate fsf_qtcb_bottom_config.connection_features
in zfcp_fsf_exchange_config_evaluate() where it belongs to.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 0282985da5 ("[SCSI] zfcp: Report fc_host_port_type as NPIV")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d50b3f43db upstream.
When using efifb with a 16-bit (5:6:5) visual, fbcon's text is rendered
in the wrong colors - e.g. text gray (#aaaaaa) is rendered as green
(#50bc50) and neighboring pixels have slightly different values
(such as #50bc78).
The reason is that fbcon loads its 16 color palette through
efifb_setcolreg(), which in turn calculates a 32-bit value to write
into memory for each palette index.
Until now, this code could only handle 8-bit visuals and didn't mask
overlapping values when ORing them.
With this patch, fbcon displays the correct colors when a qemu VM is
booted in 16-bit mode (in GRUB: "set gfxpayload=800x600x16").
Fixes: 7c83172b98 ("x86_64 EFI boot support: EFI frame buffer driver") # v2.6.24+
Signed-off-by: Max Staudt <mstaudt@suse.de>
Acked-By: Peter Jones <pjones@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9504a89247 upstream.
While VGA hotplugging worked(ish) before, it looks like that was mainly
because we'd unintentionally enable it in
valleyview_crt_detect_hotplug() when we did a force trigger. This
doesn't work reliably enough because whenever the display powerwell on
vlv gets disabled, the values set in VLV_ADPA get cleared and
consequently VGA hotplugging gets disabled. This causes bugs such as one
we found on an Intel NUC, where doing the following sequence of
hotplugs:
- Disconnect all monitors
- Connect VGA
- Disconnect VGA
- Connect HDMI
Would result in VGA hotplugging becoming disabled, due to the powerwells
getting toggled in the process of connecting HDMI.
Changes since v3:
- Expose intel_crt_reset() through intel_drv.h and call that in
vlv_display_power_well_init() instead of
encoder->base.funcs->reset(&encoder->base);
Changes since v2:
- Use intel_encoder structs instead of drm_encoder structs
Changes since v1:
- Instead of handling the register writes ourself, we just reuse
intel_crt_detect()
- Instead of resetting the ADPA during display IRQ installation, we now
reset them in vlv_display_power_well_init()
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rebase over dev_priv/drm_device embedding.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.16:
- Adjust filename, context
- Open-code for_each_intel_encoder()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 28cf71ce3e upstream.
This lets call intel_crt_reset() in contexts where IRQs are disabled and
as such, can't hold the locks required to work with the connectors.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 31051c85b5 upstream.
inode_change_ok() will be resposible for clearing capabilities and IMA
extended attributes and as such will need dentry. Give it as an argument
to inode_change_ok() instead of an inode. Also rename inode_change_ok()
to setattr_prepare() to better relect that it does also some
modifications in addition to checks.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
[bwh: Backported to 3.16:
- Drop changes to orangefs, overlayfs
- Adjust filenames, context
- In nfsd, pass dentry to nfsd_sanitize_attrs()
- Update ext3 as well]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6249033076 upstream.
To avoid clearing of capabilities or security related extended
attributes too early, inode_change_ok() will need to take dentry instead
of inode. Propagate it down to fuse_do_setattr().
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
[bwh: Backported to 3.16: open-code file_dentry()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 69bca80744 upstream.
To avoid clearing of capabilities or security related extended
attributes too early, inode_change_ok() will need to take dentry instead
of inode. Propagate dentry down to functions calling inode_change_ok().
This is rather straightforward except for xfs_set_mode() function which
does not have dentry easily available. Luckily that function does not
call inode_change_ok() anyway so we just have to do a little dance with
function prototypes.
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
[bwh: Backported to 3.16:
- Keep XFS_ERROR() calls
- Adjust context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This reverts commit be9df69943, which was
commit 31051c85b5 upstream. The backport
breaks fuse and makes a mess of xfs, which can be improved by picking
further upstream commits as I should have done in the first place.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
