This series reshuffles things around, moving the management of SMD RPM
bus clocks to the interconnect framework where they belong. This helps
us solve a couple of issues:
1. We can work towards unused clk cleanup of RPMCC without worrying
about it killing some NoC bus, resulting in the SoC dying.
Deasserting actually unused RPM clocks (among other things) will
let us achieve "true SoC-wide power collapse states", also known as
VDD_LOW and VDD_MIN.
2. We no longer have to keep tons of quirky bus clock ifs in the icc
driver. You either have a RPM clock and call "rpm set rate" or you
have a single non-RPM clock (like AHB_CLK_SRC) or you don't have any.
3. There's less overhead - instead of going through layers and layers of
the CCF, ratesetting comes down to calling max() and sending a single
RPM message. ICC is very very dynamic so that's a big plus.
The clocks still need to be vaguely described in the clk-smd-rpm driver,
as it gives them an initial kickoff, before actually telling RPM to
enable DVFS scaling. After RPM receives that command, all clocks that
have not been assigned a rate are considered unused and are shut down
in hardware, leading to the same issue as described in point 1.
We can consider marking them __initconst in the future, but this series
is very fat even without that..
Apart from that, it squashes a couple of bugs that really need fixing..
The series is merged through a topic branch to manage the dependencies
between interconnect, Qualcomm clocks and Qualcomm SoC.
Up until now, we've been aggregating the bandwidth values and only
dividing them by the bus width of the source node. This was completely
wrong, as different nodes on a given path may (and usually do) have
varying bus widths. That in turn, resulted in the calculated clock rates
being completely bogus - usually they ended up being much higher, as
NoC_A<->NoC_B links are very wide.
Since we're not using the aggregate bandwidth value for anything other
than clock rate calculations, remodel qcom_icc_bus_aggregate() to
calculate the per-context clock rate for a given provider, taking into
account the bus width of every individual node.
Fixes: 30c8fa3ec6 ("interconnect: qcom: Add MSM8916 interconnect provider driver")
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-22-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Currently, we're setting the aggregated-on-provider bandwidth on each
node, individually. That is of course incorrect and results in far too
high votes. Use the correct values to ensure we're not wasting power.
Fixes: 30c8fa3ec6 ("interconnect: qcom: Add MSM8916 interconnect provider driver")
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-21-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Up until now, for some reason we've only been setting bandwidth values
on the active-only context. That pretty much meant that RPM could lift
all votes when entering sleep mode. Or never sleep at all.
That in turn could potentially break things like USB wakeup, as the
connection between APSS and SNoC/PNoC would simply be dead.
Set the values appropriately.
Fixes: 30c8fa3ec6 ("interconnect: qcom: Add MSM8916 interconnect provider driver")
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-20-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
SMD RPM only provides two buckets, one each for the active-only and
active-sleep RPM contexts. Use the correct constant to allocate and
operate on them.
This will make the qcom,icc.h header no longer work with this driver,
mostly because.. it was never meant to! The commit that introduced
bucket support to SMD RPM was trying to shove a square into a round
hole and it did not work out very well. That said, there are no
active users of SMD RPM ICC + qcom,icc.h, so that doesn't hurt.
Fixes: dcbce7b0a7 ("interconnect: qcom: icc-rpm: Support multiple buckets")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-19-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The interconnect bus clocks are now handled within the ICC framework.
They still however need to get a kickstart *before* we call
clk_smd_rpm_enable_scaling(), or RPM will assume that they should all
be running at 0 kHz and the system will inevitably die.
Separate them out to ensure such a kickstart can still take place.
As a happy accident, the file got smaller:
Total: Before=41951, After=41555, chg -0.94%
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-18-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The sole purpose of bus clocks that were previously registered with
rpmcc was to convey the aggregated bandwidth to RPM. There's no good
reason to keep them outside the interconnect framework, as it only
adds to the plentiful complexity.
Add the required code to handle these clocks from within SMD RPM ICC.
RPM-owned bus clocks are no longer considered a thing, but sadly we
have to allow for the existence of HLOS-owned bus clocks, as some
(mostly older) SoCs (ab)use these for bus scaling (e.g. MSM8998 and
&mmcc AHB_CLK_SRC).
This in turn is trivially solved with a single *clk, which is filled
and used iff qp.bus_clk_desc is absent and we have a "bus" clock-names
entry in the DT node.
This change should(tm) be fully compatible with all sorts of old
Device Trees as far as the interconnect functionality goes (modulo
abusing bus clock handles or wrongly using the qcom,icc.h binding,
but that's a mistake in and of itself).
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-17-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assign the necessary definitions to migrate to the new bus clock
handling mechanism.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-16-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assign the necessary definitions to migrate to the new bus clock
handling mechanism.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-15-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assign the necessary definitions to migrate to the new bus clock
handling mechanism.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-14-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assign the necessary definitions to migrate to the new bus clock
handling mechanism.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-13-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assign the necessary definitions to migrate to the new bus clock
handling mechanism.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-12-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assign the necessary definitions to migrate to the new bus clock
handling mechanism.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-11-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the definitions for RPM bus clocks that will be used by many
different platforms.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-10-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Introduce qcom_icc_rpm_set_bus_rate() in preparation for handling RPM
clock resources within the interconnect framework. This lets us greatly
simplify all of the code handling, as setting the rate comes down to:
u32 rate_khz = max(clk.sleep_rate, clk.active_rate, clk_a.active_rate)
write_to_rpm(clock.description, rate_khz);
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-9-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
smd-rpm.h is not very useful as-is and both files are always included
anyway.. Combine them.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-8-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Currently the header does not provide all the required dependencies.
Fix it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-7-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The downstream kernel employs the concept of "keeping the bus alive"
by voting for the minimum (XO/19.2MHz) rate at all times on certain
(well, most) buses. This is a very important thing to have, as if we
either have a lackluster/wrong DT that doesn't specify a (high enough)
vote on a certain bus, we may lose access to the entire bus altogether.
This is very apparent when we only start introducing interconnect
support on a given platform and haven't yet introduced voting on all
peripherals.
The same can happen if we only have a single driver casting a vote on
a certain bus and that driver exits/crashes/suspends.
The keepalive vote is limited to the ACTIVE bucket, as keeping a
permanent vote on the SLEEP one could prevent the platform from properly
entering low power mode states.
Introduce the very same concept, with a slight twist: the vendor
kernel checks whether the rate is zero before setting the minimum
vote, but that's rather silly, as in doing so we're at the mercy
of CCF. Instead, explicitly clamp the rates to always be >= 19.2 MHz
for providers with keep_alive=true.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-6-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
icc_smd_rpm will do bus clock votes itself rather than taking the
unnecessary detour through the clock subsystem. However, it can only
do that after the clocks have been handed off and scaling has been
enabled in the RPM in clk-smd-rpm.
Move the icc_smd_rpm registration from smd-rpm.c to clk-smd-rpm.c
to avoid any possible races. icc_smd_rpm gets the driver data from
the smd-rpm device, so still register the platform device on the
smd-rpm parent device.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
[Konrad: remove unrelated cleanups]
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-5-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In preparation for handling the bus clocks in the icc driver, carve out
some defines and a struct definition to the common rpm header.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-4-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a preprocessor define to indicate the number of RPM contexts/states.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-2-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SMD RPM interconnect driver requires different icc tags to the
RPMh driver. Add bindings to reflect that.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-1-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
With the minimal system suspend support in place for the PCIe driver that
keeps the interconnect path voted, the ALWAYS_ON flag can now be dropped.
Also, the pwrsts PWRSTS_RET_ON flag should be used to allow the GDSCs to
enter the retention state when the parent domain get's turned off during
system suspend.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230707075926.11726-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Update my email address from the defunct codeaurora.org domain to the
current quicinc.com domain.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20230627173123.9221-1-quic_tdas@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There are 10 more GDSCs that we've not been caring about, and by extension
(and perhaps even more importantly), not putting to sleep. Add them.
Fixes: d65d005f9a ("clk: qcom: add sc8280xp GCC driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230620-topic-sc8280_gccgdsc-v2-3-562c1428c10d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
All of the 8280's GCC GDSCs can and should use the retain registers so
as not to lose their state when entering lower power modes.
Fixes: d65d005f9a ("clk: qcom: add sc8280xp GCC driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230620-topic-sc8280_gccgdsc-v2-1-562c1428c10d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There are 10 more GDSCs that we've not been caring about, and by extension
(and perhaps even more importantly), not putting to sleep. Add them.
Fixes: a66a82f2a5 ("dt-bindings: clock: Add Qualcomm SC8280XP GCC bindings")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230620-topic-sc8280_gccgdsc-v2-2-562c1428c10d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the nowadays-prefered and marginally faster way of looking up parent
clocks in the device tree. It also allows for clock-names-independent
operation, so long as the order (which is enforced by schema) is kept.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230315-topic-lagoon_gpu-v2-1-afcdfb18bb13@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the clocks needed for enabling USB in IPQ9574
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/d1c5aa4a8535c645fdb06df62a562918516ba0c6.1686289721.git.quic_varada@quicinc.com
[bjorn: Clock defines split out to separate commit]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the clocks needed for enabling USB in IPQ9574
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/d1c5aa4a8535c645fdb06df62a562918516ba0c6.1686289721.git.quic_varada@quicinc.com
[bjorn: Split from driver patch, to allow merging into dts tree]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On msm8226 we also have OXILICX_GDSC but we need a slighly different
config, with a .cxcs defined for clock but with no parent.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20230506-msm8226-oxilicx-v2-1-f7e4ebff3d61@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.
The answer is "No. No we cannot".
I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street. And at the yearly
maintainer summit, we will all sing the alphabet song together.
I doubt I will keep doing this. At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.
Repeats: 80e62bc848 ("MAINTAINERS: re-sort all entries and fields")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- swiotlb area sizing fixes (Petr Tesarik)
-----BEGIN PGP SIGNATURE-----
iQI/BAABCgApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAmSq57sLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYOh0xAAkwklIxxzXvNlgjvy2hdgPWImPS8tGPDSIsqA9TDD
WDZq89nz/ndnchdPObDvyJXmfBgqa0qCHqopBVPqMKv5a1pKZhrRXYlbajGQQwji
MIqefTLZ/VGw7bDpEivOt+yadwQ3KxuxWWs7/JPKLLReSJ22H8P+jkrK7P7kBL5X
YaMtZG9d86fvFHnQHKdAOlF1iCvnoZDHPcvaZbI6m5mMSZ+HIYqK5pP1MTUEAbIU
MX4ZSI7/mL0q67+kZuM/NCSeq1pH0Cd0D2DGm+8k/y87G81GS6E5Wgg+xO7vYiXf
5ChuwlAO9K9KhH7NIRkKhkad/Ii89ENXSyv5gmPRoKYK5FXajnHSlJTUrZojV6XC
Pbsd9ATVzV0rY61EPyh6G1a+Ttp/pwMp+W0I2fi032GVAePQ/vhB9x9O+2O/3QiC
v80nUSatkciZncWqkguhp3NONsRmLKep3CCQnEAA/gLs27B0avdQeslnqbOOUQKd
Si+djIoel8ONjQ+mW8eFCsVYMH1xFSo0aGsgGe0y2cyBE3DN1AW9eRnOXWT4C1PR
UyDlx8ACs87ojec+YRQFYk2/PbsU7CQiH1pteXvBHcbhiVUAvrtXtg6ANQ+7066P
IIduAZmlHcHb1BhyrSQbAtRllVLIp/l9IAkCSY9SvL0tjh/B5CaRBD5m2Taow5I/
KUI=
=4Lfc
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
- swiotlb area sizing fixes (Petr Tesarik)
* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: reduce the number of areas to match actual memory pool size
swiotlb: always set the number of areas before allocating the pool
boot reordering work
-----BEGIN PGP SIGNATURE-----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=RZFV
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fpu fix from Borislav Petkov:
- Do FPU AP initialization on Xen PV too which got missed by the recent
boot reordering work
* tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/xen: Fix secondary processors' FPU initialization
On shutdown or kexec, the kernel tries to park the non-boot CPUs with an
INIT IPI. But the same code path is also used by the crash utility. If the
CPU which panics is not the boot CPU then it sends an INIT IPI to the boot
CPU which resets the machine. Prevent this by validating that the CPU which
runs the stop mechanism is the boot CPU. If not, leave the other CPUs in
HLT.
-----BEGIN PGP SIGNATURE-----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=DOCF
-----END PGP SIGNATURE-----
Merge tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A single fix for the mechanism to park CPUs with an INIT IPI.
On shutdown or kexec, the kernel tries to park the non-boot CPUs with
an INIT IPI. But the same code path is also used by the crash utility.
If the CPU which panics is not the boot CPU then it sends an INIT IPI
to the boot CPU which resets the machine.
Prevent this by validating that the CPU which runs the stop mechanism
is the boot CPU. If not, leave the other CPUs in HLT"
* tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smp: Don't send INIT to boot CPU
* Fix an uninitialized variable warning.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ2qTKExjcn+O1o2YRKO3ySh0YRpgUCZKjUjwAKCRBKO3ySh0YR
pn92AQC4gY9GOyKcc/aiAd/t1u8gGxnFtcN06xh4TdVArMM4/AD/UtEKx9LYuaSF
pyhw5SfzxI555HfXkA8ci/D+BxguVQs=
=/vX1
-----END PGP SIGNATURE-----
Merge tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fix from Darrick Wong:
"Nothing exciting here, just getting rid of a gcc warning that I got
tired of seeing when I turn on gcov"
* tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix uninit warning in xfs_growfs_data
-----BEGIN PGP SIGNATURE-----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=F8D0
-----END PGP SIGNATURE-----
Merge tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- fix potential use after free in unmount
- minor cleanup
- add worker to cleanup stale directory leases
* tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Add a laundromat thread for cached directories
smb: client: remove redundant pointer 'server'
cifs: fix session state transition to avoid use-after-free issue
Lockdep is certainly right to complain about
(&vma->vm_lock->lock){++++}-{3:3}, at: vma_start_write+0x2d/0x3f
but task is already holding lock:
(&mapping->i_mmap_rwsem){+.+.}-{3:3}, at: mmap_region+0x4dc/0x6db
Invert those to the usual ordering.
Fixes: 33313a747e ("mm: lock newly mapped VMA which can be modified after it becomes visible")
Cc: stable@vger.kernel.org
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZKmgXAAKCRDdBJ7gKXxA
joqDAP0V520Jy0cyJrRMvaQRFMqtVeDOdTpAue7ZOQHSi/LZnAD9EEAxDpYF/V4x
PO27ixXQ4Glm2iYgH7bDX7J73WiA3wg=
=JsYW
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull hotfixes from Andrew Morton:
"16 hotfixes. Six are cc:stable and the remainder address post-6.4
issues"
The merge undoes the disabling of the CONFIG_PER_VMA_LOCK feature, since
it was all hopefully fixed in mainline.
* tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
lib: dhry: fix sleeping allocations inside non-preemptable section
kasan, slub: fix HW_TAGS zeroing with slub_debug
kasan: fix type cast in memory_is_poisoned_n
mailmap: add entries for Heiko Stuebner
mailmap: update manpage link
bootmem: remove the vmemmap pages from kmemleak in free_bootmem_page
MAINTAINERS: add linux-next info
mailmap: add Markus Schneider-Pargmann
writeback: account the number of pages written back
mm: call arch_swap_restore() from do_swap_page()
squashfs: fix cache race with migration
mm/hugetlb.c: fix a bug within a BUG(): inconsistent pte comparison
docs: update ocfs2-devel mailing list address
MAINTAINERS: update ocfs2-devel mailing list address
mm: disable CONFIG_PER_VMA_LOCK until its fixed
fork: lock VMAs of the parent process when forking
When forking a child process, the parent write-protects anonymous pages
and COW-shares them with the child being forked using copy_present_pte().
We must not take any concurrent page faults on the source vma's as they
are being processed, as we expect both the vma and the pte's behind it
to be stable. For example, the anon_vma_fork() expects the parents
vma->anon_vma to not change during the vma copy.
A concurrent page fault on a page newly marked read-only by the page
copy might trigger wp_page_copy() and a anon_vma_prepare(vma) on the
source vma, defeating the anon_vma_clone() that wasn't done because the
parent vma originally didn't have an anon_vma, but we now might end up
copying a pte entry for a page that has one.
Before the per-vma lock based changes, the mmap_lock guaranteed
exclusion with concurrent page faults. But now we need to do a
vma_start_write() to make sure no concurrent faults happen on this vma
while it is being processed.
This fix can potentially regress some fork-heavy workloads. Kernel
build time did not show noticeable regression on a 56-core machine while
a stress test mapping 10000 VMAs and forking 5000 times in a tight loop
shows ~5% regression. If such fork time regression is unacceptable,
disabling CONFIG_PER_VMA_LOCK should restore its performance. Further
optimizations are possible if this regression proves to be problematic.
Suggested-by: David Hildenbrand <david@redhat.com>
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Closes: https://lore.kernel.org/all/dbdef34c-3a07-5951-e1ae-e9c6e3cdf51b@kernel.org/
Reported-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Closes: https://lore.kernel.org/all/b198d649-f4bf-b971-31d0-e8433ec2a34c@applied-asynchrony.com/
Reported-by: Jacob Young <jacobly.alt@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217624
Fixes: 0bff0aaea0 ("x86/mm: try VMA lock-based page fault handling first")
Cc: stable@vger.kernel.org
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mmap_region adds a newly created VMA into VMA tree and might modify it
afterwards before dropping the mmap_lock. This poses a problem for page
faults handled under per-VMA locks because they don't take the mmap_lock
and can stumble on this VMA while it's still being modified. Currently
this does not pose a problem since post-addition modifications are done
only for file-backed VMAs, which are not handled under per-VMA lock.
However, once support for handling file-backed page faults with per-VMA
locks is added, this will become a race.
Fix this by write-locking the VMA before inserting it into the VMA tree.
Other places where a new VMA is added into VMA tree do not modify it
after the insertion, so do not need the same locking.
Cc: stable@vger.kernel.org
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
