Add 'nxp,ctrl-ids' for SCMI firmware to configure the board ctrls as
wakeup sources.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX95 has two on-chip temperature sensors, one is inside anamix block.
This is to add the anamix temperature thermal zone and its cooling
device.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the thermal trip points for automotive and extended industrial
temperature qualification processors.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With 'max-rx-timeout-ms' property added in 'Documentation/devicetree/
indings/firmware/arm,scmi.yaml', set the value for i.MX95.
NXP i.MX95 SCMI Firmware designation does not allow timeout, it will not
recover if the Agents use timeout design. So set a large value (5000ms)
here.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Kontron Electronics DL i.MX8MM consists of the BL i.MX8MM board
and a 7" LVDS panel. Provide an overlay that enables the panel.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Kontron Electronics BL i.MX8MM has oboard disply bridges for
DSI->HDMI and DSI->LVDS conversion. The DSI interface is muxed by
a GPIO-controlled switch to one of these two bridges.
By default the HDMI bridge is enabled. The LVDS bridge can be
selected by loading an additional (panel-specific) overlay.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove unused property cooling-max-state and cooling-min-state.
Remove undocument property #cooling-cells for ti,amc6821.
Fix below dtb_check warning:
arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-cx.dtb: fan-temperature-ctrlr@18: '#cooling-cells', 'cooling-max-state', 'cooling-min-state' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/hwmon/ti,amc6821.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
So far, only WFI is supported on i.MX8mp platform. Add support for
deeper cpuidle state "cpu-pd-wait" that would allow for better power
usage during runtime. This is a port from NXP downstream kernel.
Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PCIe of i.MX8MP is dual role PCIe controller, which can work as root
complex (RC) mode and endpoint (EP) mode. Add overlay file to let it work
as EP mode.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add rev2 dtsi. Although uboot fixup can change compatible string
fsl,lx2160a-pcie to fsl,ls2088a-pcie since 2019, it is quite confused and
should correctly reflect hardware status. So add fsl-lx2160a-rev2.dtsi to
overwrite pcie's compatible string.
Add PCIe EP nodes.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PicoITX carrier board.
This system is populated with serial console, EQoS ethernet, eMMC, SD, SPI NOR,
LEDs and USB 3.0 host used in USB 2.0 mode on PicoITX.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for DH electronics i.MX8MP DHCOM SoM on DRC02 carrier board.
This system is populated with two ethernet ports, two CANs, RS485 and RS232,
USB, capacitive buttons and an OLED display.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The IOTA2 Lumpy board is based on the i.MX8MPlus EVK.
Basic features are:
- 4GB LPDDR4
- 64GB eMMC
- 2x 1GB Ethernet
- USB 3.0 Type-C dual role port, without power delivery
- USB 3.0 Type-A host port
- RGB LED - PWM driven
- speaker - PWM driven
- RTC with super capacitor backup
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Toradex Verdin Ivy carrier board support. One notable feature of Ivy
is the analog inputs. These inputs are multiplexed, allowing the same
input to measure either voltage or current. For current measurements,
a GPIO switch enables or disables the shunt resistor. This process is
automatically managed by the Linux kernel using the IIO and MUX
subsystems. Voltage measurement is always enabled, but the voltage
measured by the ADC is scaled by a cascade voltage divider. In the
device tree, the equivalent gain of the voltage divider is used, which
can be calculated as follows:
------------
+ |
.-.
R1=30K | |
| |
'-'
|-------------------
Analog Input (AIN) | |
.-. .-.
R2=10K | | R3=30K | |
| | | |
'-' '-'
| |
| |--------
| .-. +
| R4=10K | |
| | | ADC Input (Channels 0 and 1)
| '-'
- | | -
-----------| |--------
=== ===
GND GND
Vin = Analog Input (AIN)
Vout = ADC Input
Rth = Thevenin Equiv. Resistance
Vth = Thevenin Equiv. Voltage
RL = Load Resistor
R1 = 30K, R2 = 10K, R3 = 30K, R4 = 10K
RL = R4 = 10K
Rth = (R1 // R2) + R3 = 37500 Ohms
Vth = (Vin * R2) / (R1 + R2) = Vin/4;
Vout = (Vth * RL)/ (Rth + RL) = Vth/4.75 = Vin/19
Gain = Vout/Vin = 1/19
https://www.toradex.com/products/carrier-board/ivy-carrier-board
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add labels to ti-ads1015 and fec ethernet mdio node to make it easier to
reference them from other nodes.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Toradex Verdin Ivy carrier board support. One notable feature of Ivy
is the analog inputs. These inputs are multiplexed, allowing the same
input to measure either voltage or current. For current measurements,
a GPIO switch enables or disables the shunt resistor. This process is
automatically managed by the Linux kernel using the IIO and MUX
subsystems. Voltage measurement is always enabled, but the voltage
measured by the ADC is scaled by a cascade voltage divider. In the
device tree, the equivalent gain of the voltage divider is used, which
can be calculated as follows:
------------
+ |
.-.
R1=30K | |
| |
'-'
|-------------------
Analog Input (AIN) | |
.-. .-.
R2=10K | | R3=30K | |
| | | |
'-' '-'
| |
| |--------
| .-. +
| R4=10K | |
| | | ADC Input (Channels 0 and 1)
| '-'
- | | -
-----------| |--------
=== ===
GND GND
Vin = Analog Input (AIN)
Vout = ADC Input
Rth = Thevenin Equiv. Resistance
Vth = Thevenin Equiv. Voltage
RL = Load Resistor
R1 = 30K, R2 = 10K, R3 = 30K, R4 = 10K
RL = R4 = 10K
Rth = (R1 // R2) + R3 = 37500 Ohms
Vth = (Vin * R2) / (R1 + R2) = Vin/4;
Vout = (Vth * RL)/ (Rth + RL) = Vth/4.75 = Vin/19
Gain = Vout/Vin = 1/19
https://www.toradex.com/products/carrier-board/ivy-carrier-board
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a label to ti-ads1015 node to make it easier to reference it
from other nodes.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A GPIO fan may be connected to Pollux fan header. The fan should
activate at 60°C and stay active until critical SoC temperature is
reached and the board shuts down.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The device tree defines the touchscreen controller, but it cannot be
enabled because it lacks a reference label.
This commit adds a label to allow it to be referenced and enabled.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add aliases for the RTCs on the Gateworks Venice boards and on the imx8m
SoC. This ensures that the primary RTC is always the one on-board
provided by the Gateworks System Controller (GSC) which is battery
backed as opposed to the one in the IMX8M.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add an overlay file to enable I3C support on the i.MX93, replacing I2C1
with I3C. I3C is compatible with I2C, but it has not yet been enabled in
arm64's defconfig. This overlay allows users to conveniently utilize I3C
on the imx93-9x9-qsb platform until I3C and its driver become more mature
and ready for full switch to I3C.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW74xx D revision has added a M2SKT_GPIO10 GPIO which routes to the
GPIO10 pin of the M.2 socket for compatibility with certain devices.
Add the iomux and a line name for this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DTS code coding style expects exactly one space before '{'
character.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for the Kontron Electronics i.MX8MP SMARC module
(which uses the OSM-S i.MX8MP SoM) on the Kontron SMARC eval carrier.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for the Kontron Electronics OSM-S i.MX8MP SoM
and the matching baseboard BL i.MX8MP.
The SoM hardware complies to the Open Standard Module (OSM) 1.1
specification, size S (https://sget.org/standards/osm).
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add wm8962 sound card which connects to sai3.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In lpi2c2 node, default pinctrl and sleep pinctrl have the same value.
So "sleep" pinctrl is redundant and remove it.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add following peripherals support for the Emtop i.MX8M Mini Baseboard
* Wi-Fi
* Audio
* SD card
* RTC
* CAN bus
* USB OTG
Signed-off-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add USB4 HOST to Apalis-iMX8QM SOM and its carrier boards.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for audio-codec NAU88C22 present on the Apalis Evaluation
Board v1.2 carrier board.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add audio support to Apalis-iMX8QM and its carrier boards. These includes:
* On SOM i2s sound card
* On SOM spdif sound card
* Enabling Audiomix and Asynchronous Sample Rate Converter
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set critical/alert thermal thresholds for all relevant SOC
temperature trips to the IT value (max T_junction 105 degree
Celsius) in accordance with the IT grade of the SOM.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no adma pwm on iMX8QM, so remove it from the DT. When enabled,
this cause warnings on resource partition ownership check by U-Boot
that receives messages from SCU firmware saying that these resources are
not owned:
Booting using the fdt blob at 0x9d400000
Loading Device Tree to 00000000fd622000, end 00000000fd66efff ... OK
Disable pwm@5a190000 rsrc 188 not owned
Disable clock-controller@5a590000 rsrc 188 not owned
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disable SD/eMMC UHS modes for NXP boards which do not set VCCQ voltage
supply to 1.8V by default, such as S32G274A-EVB and S32G274A-RDB2.
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add dbi2 and iatu reg for i.MX8MM PCIe EP.
For i.MX8M PCIe EP, the dbi2 and atu addresses are pre-defined in the
driver. This method is not good.
In commit b7d67c6130 ("PCI: imx6: Add iMX95 Endpoint (EP) support"),
Frank suggests to fetch the dbi2 and atu from DT directly. This commit is
preparation to do that for i.MX8MM PCIe EP.
These changes wouldn't break driver function. When "dbi2" and "atu"
properties are present, i.MX PCIe driver would fetch the according base
addresses from DT directly. If only two reg properties are provided, i.MX
PCIe driver would fall back to the old method.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add dbi2 and iatu reg for i.MX8MP PCIe EP.
For i.MX8M PCIe EP, the dbi2 and atu addresses are pre-defined in the
driver. This method is not good.
In commit b7d67c6130 ("PCI: imx6: Add iMX95 Endpoint (EP) support"),
Frank suggests to fetch the dbi2 and atu from DT directly. This commit is
preparation to do that for i.MX8MP PCIe EP.
These changes wouldn't break driver function. When "dbi2" and "atu"
properties are present, i.MX PCIe driver would fetch the according base
addresses from DT directly. If only two reg properties are provided, i.MX
PCIe driver would fall back to the old method.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add dbi2 and iatu reg for i.MX8MQ PCIe EP.
For i.MX8M PCIe EP, the dbi2 and atu addresses are pre-defined in the
driver. This method is not good.
In commit b7d67c6130 ("PCI: imx6: Add iMX95 Endpoint (EP) support"),
Frank suggests to fetch the dbi2 and atu from DT directly. This commit is
preparation to do that for i.MX8MQ PCIe EP.
These changes wouldn't break driver function. When "dbi2" and "atu"
properties are present, i.MX PCIe driver would fetch the according base
addresses from DT directly. If only two reg properties are provided, i.MX
PCIe driver would fall back to the old method.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cpu_emergency_register_virt_callback() function is used
unconditionally by the x86 kvm code, but it is declared (and defined)
conditionally:
#if IS_ENABLED(CONFIG_KVM_INTEL) || IS_ENABLED(CONFIG_KVM_AMD)
void cpu_emergency_register_virt_callback(cpu_emergency_virt_cb *callback);
...
leading to a build error when neither KVM_INTEL nor KVM_AMD support is
enabled:
arch/x86/kvm/x86.c: In function ‘kvm_arch_enable_virtualization’:
arch/x86/kvm/x86.c:12517:9: error: implicit declaration of function ‘cpu_emergency_register_virt_callback’ [-Wimplicit-function-declaration]
12517 | cpu_emergency_register_virt_callback(kvm_x86_ops.emergency_disable_virtualization_cpu);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/x86/kvm/x86.c: In function ‘kvm_arch_disable_virtualization’:
arch/x86/kvm/x86.c:12522:9: error: implicit declaration of function ‘cpu_emergency_unregister_virt_callback’ [-Wimplicit-function-declaration]
12522 | cpu_emergency_unregister_virt_callback(kvm_x86_ops.emergency_disable_virtualization_cpu);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix the build by defining empty helper functions the same way the old
cpu_emergency_disable_virtualization() function was dealt with for the
same situation.
Maybe we could instead have made the call sites conditional, since the
callers (kvm_arch_{en,dis}able_virtualization()) have an empty weak
fallback. I'll leave that to the kvm people to argue about, this at
least gets the build going for that particular config.
Fixes: 590b09b1d8 ("KVM: x86: Register "emergency disable" callbacks when virt is enabled")
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: Kai Huang <kai.huang@intel.com>
Cc: Chao Gao <chao.gao@intel.com>
Cc: Farrah Chen <farrah.chen@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
imx: use devie name instead of genereic imx_mu_chan as interrupt name
qcom: enable sa8255p and qcs8300 ipc controllers
bcm2835: Fix timeout during suspend mode
mailbox: convert to use use of_property_match_string
mediatek: enable mt8188
spreadtrum: use devm_clk_get_enabled helpers
rockchip: fix device-id typo
-----BEGIN PGP SIGNATURE-----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=nCRH
-----END PGP SIGNATURE-----
Merge tag 'mailbox-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox
Pull mailbox updates from Jassi Brar:
- fix kconfig dependencies (mhu-v3, omap2+)
- use devie name instead of genereic imx_mu_chan as interrupt name
(imx)
- enable sa8255p and qcs8300 ipc controllers (qcom)
- Fix timeout during suspend mode (bcm2835)
- convert to use use of_property_match_string (mailbox)
- enable mt8188 (mediatek)
- use devm_clk_get_enabled helpers (spreadtrum)
- fix device-id typo (rockchip)
* tag 'mailbox-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox:
mailbox, remoteproc: omap2+: fix compile testing
dt-bindings: mailbox: qcom-ipcc: Document QCS8300 IPCC
dt-bindings: mailbox: qcom-ipcc: document the support for SA8255p
dt-bindings: mailbox: mtk,adsp-mbox: Add compatible for MT8188
mailbox: Use of_property_match_string() instead of open-coding
mailbox: bcm2835: Fix timeout during suspend mode
mailbox: sprd: Use devm_clk_get_enabled() helpers
mailbox: rockchip: fix a typo in module autoloading
mailbox: imx: use device name in interrupt name
mailbox: ARM_MHU_V3 should depend on ARM64
I2C host fixes for v6.12-rc1 (from Andi)
The DesignWare driver now has the correct ENABLE-ABORT sequence,
ensuring ABORT can always be sent when needed.
In the SynQuacer controller we now check for PCLK as an optional
clock, allowing ACPI to directly provide the clock rate.
The recent KEBA driver required a dependency fix in Kconfig.
The XIIC driver now has a corrected power suspend sequence.
-----BEGIN PGP SIGNATURE-----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=CZPe
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.12-rc1-additional_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- fix DesignWare driver ENABLE-ABORT sequence, ensuring ABORT can
always be sent when needed
- check for PCLK in the SynQuacer controller as an optional clock,
allowing ACPI to directly provide the clock rate
- KEBA driver Kconfig dependency fix
- fix XIIC driver power suspend sequence
* tag 'i2c-for-6.12-rc1-additional_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: xiic: Fix pm_runtime_set_suspended() with runtime pm enabled
i2c: keba: I2C_KEBA should depend on KEBA_CP500
i2c: synquacer: Deal with optional PCLK correctly
i2c: designware: fix controller is holding SCL low while ENABLE bit is disabled
- handle chained SGLs in the new tracing code (Christoph Hellwig)
-----BEGIN PGP SIGNATURE-----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=zjTS
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-6.12-2024-09-29' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fix from Christoph Hellwig:
- handle chained SGLs in the new tracing code (Christoph Hellwig)
* tag 'dma-mapping-6.12-2024-09-29' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: fix DMA API tracing for chained scatterlists
These are mostly minor updates. There are two drivers (lpfc and
mpi3mr) which missed the initial pull and a core change to retry a
start/stop unit which affect suspend/resume.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZvh4QiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQajAQDx561I
cgbPZjZkSOYp+qJowaphyySZ1SS8pfMlVAIiXQEAs4SqhIN8e9QWpgI0bA7X7xtB
UiOUsIHPHM+BFU6kbJQ=
=qjsp
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"These are mostly minor updates.
There are two drivers (lpfc and mpi3mr) which missed the initial
pull and a core change to retry a start/stop unit which affect
suspend/resume"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi: lpfc: Update lpfc version to 14.4.0.5
scsi: lpfc: Support loopback tests with VMID enabled
scsi: lpfc: Revise TRACE_EVENT log flag severities from KERN_ERR to KERN_WARNING
scsi: lpfc: Ensure DA_ID handling completion before deleting an NPIV instance
scsi: lpfc: Fix kref imbalance on fabric ndlps from dev_loss_tmo handler
scsi: lpfc: Restrict support for 32 byte CDBs to specific HBAs
scsi: lpfc: Update phba link state conditional before sending CMF_SYNC_WQE
scsi: lpfc: Add ELS_RSP cmd to the list of WQEs to flush in lpfc_els_flush_cmd()
scsi: mpi3mr: Update driver version to 8.12.0.0.50
scsi: mpi3mr: Improve wait logic while controller transitions to READY state
scsi: mpi3mr: Update MPI Headers to revision 34
scsi: mpi3mr: Use firmware-provided timestamp update interval
scsi: mpi3mr: Enhance the Enable Controller retry logic
scsi: sd: Fix off-by-one error in sd_read_block_characteristics()
scsi: pm8001: Do not overwrite PCI queue mapping
scsi: scsi_debug: Remove a useless memset()
scsi: pmcraid: Convert comma to semicolon
scsi: sd: Retry START STOP UNIT commands
scsi: mpi3mr: A performance fix
scsi: ufs: qcom: Update MODE_MAX cfg_bw value
...
Assorted minor syzbot fixes, and for bigger stuff:
- Fix two disk accounting rewrite bugs
- Disk accounting keys use the version field of bkey so that journal
replay can tell which updates have been applied to the btree. This is
set in the transaction commit path, after we've gotten our journal
reservation (and our time ordering), but the
BCH_TRANS_COMMIT_skip_accounting_apply flag that journal replay uses
was incorrectly skipping this for new updates generated prior to
journal replay.
This fixes the underlying cause of an assertion pop in
disk_accounting_read.
- A couple fixes for disk accounting + device removal. Checking if
acocunting replicas entries were marked in the superblock was being
done at the wrong point, when deltas in the journal could still zero
them out, and then additionally we'd try to add a missing replicas
entry to the superblock without checking if it referred to an invalid
(removed) device.
- A whole slew of repair fixes
- fix infinite loop in propagate_key_to_snapshot_leaves(), this fixes
an infinite loop when repairing a filesystem with many snapshots
- fix incorrect transaction restart handling leading to occasional
"fsck counted ..." warnings"
- fix warning in __bch2_fsck_err() for bkey fsck errors
- check_inode() in fsck now correctly checks if the filesystem was
clean
- there shouldn't be pending logged ops if the fs was clean, we now
check for this
- remove_backpointer() doesn't remove a dirent that doesn't actually
point to the inode
- many more fsck errors are AUTOFIX
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEKnAFLkS8Qha+jvQrE6szbY3KbnYFAmb4QtsACgkQE6szbY3K
bnYx4A//bhGgZYgP55FxduuxUH8XjX2eOnXwuPv/MmYO/4oCok5VBa9bRDTVXhIK
PtY4pP2IJZ3+u963mwbwJAawsPA01AEEty9tE+AdXbltDRQ03I33OEuIy0HFIso2
s8VBkVPbru6yU4RCCvYNIVvRG/9GOL+J0GgrR1t05zHVyKXe1FuS00Yq5+z3niNP
HtuGTsD273Nnhikz47bqyD+M6VizU+uzSUFLgnB3zrzpb+gPSGETSwgc4ggajlM4
2P10Vc4L/Nb3KYV9RW+C3WpRfUR/o8BZA3wjJfNo0JeA4iDaUbltSjpCA07EcAnA
3D6Omzqkm4aobL2WlvioT0UhZx4t8X/8x5t5F9HyX52i1k+g87oMT9/KIKec1Dzd
8vQCwCdXFfWaLSZoOJsHyIljip7BuRLKhWwKosdzzLIAnRQy5StxAhsG99fNStu6
JOWICPNCn1b6SkktnoKou1unL+K5RczeNfAxMAjcJjTD7IIAmytLe4mdRbP9q+Oa
x8no7pttbb4JnoRvfo42GVz8KWQR07oN/Zy7mH3K4Y0Ix+xDOrLqlfLIDLGpxMNv
HZz+UPchdlfpYJO+nTLoAOGXZWnKDqg70SAEcWKDc82Ri4vNOhraYDZvXrzl9qE+
63RPzqDbg3uXGxLYMvujjPe610QkPxS9zKKyDvUZZx0ZiUX4CjI=
=cdrz
-----END PGP SIGNATURE-----
Merge tag 'bcachefs-2024-09-28' of git://evilpiepirate.org/bcachefs
Pull more bcachefs updates from Kent Overstreet:
"Assorted minor syzbot fixes, and for bigger stuff:
Fix two disk accounting rewrite bugs:
- Disk accounting keys use the version field of bkey so that journal
replay can tell which updates have been applied to the btree.
This is set in the transaction commit path, after we've gotten our
journal reservation (and our time ordering), but the
BCH_TRANS_COMMIT_skip_accounting_apply flag that journal replay
uses was incorrectly skipping this for new updates generated prior
to journal replay.
This fixes the underlying cause of an assertion pop in
disk_accounting_read.
- A couple of fixes for disk accounting + device removal.
Checking if acocunting replicas entries were marked in the
superblock was being done at the wrong point, when deltas in the
journal could still zero them out, and then additionally we'd try
to add a missing replicas entry to the superblock without checking
if it referred to an invalid (removed) device.
A whole slew of repair fixes:
- fix infinite loop in propagate_key_to_snapshot_leaves(), this fixes
an infinite loop when repairing a filesystem with many snapshots
- fix incorrect transaction restart handling leading to occasional
"fsck counted ..." warnings
- fix warning in __bch2_fsck_err() for bkey fsck errors
- check_inode() in fsck now correctly checks if the filesystem was
clean
- there shouldn't be pending logged ops if the fs was clean, we now
check for this
- remove_backpointer() doesn't remove a dirent that doesn't actually
point to the inode
- many more fsck errors are AUTOFIX"
* tag 'bcachefs-2024-09-28' of git://evilpiepirate.org/bcachefs: (35 commits)
bcachefs: check_subvol_path() now prints subvol root inode
bcachefs: remove_backpointer() now checks if dirent points to inode
bcachefs: dirent_points_to_inode() now warns on mismatch
bcachefs: Fix lost wake up
bcachefs: Check for logged ops when clean
bcachefs: BCH_FS_clean_recovery
bcachefs: Convert disk accounting BUG_ON() to WARN_ON()
bcachefs: Fix BCH_TRANS_COMMIT_skip_accounting_apply
bcachefs: Check for accounting keys with bversion=0
bcachefs: rename version -> bversion
bcachefs: Don't delete unlinked inodes before logged op resume
bcachefs: Fix BCH_SB_ERRS() so we can reorder
bcachefs: Fix fsck warnings from bkey validation
bcachefs: Move transaction commit path validation to as late as possible
bcachefs: Fix disk accounting attempting to mark invalid replicas entry
bcachefs: Fix unlocked access to c->disk_sb.sb in bch2_replicas_entry_validate()
bcachefs: Fix accounting read + device removal
bcachefs: bch_accounting_mode
bcachefs: fix transaction restart handling in check_extents(), check_dirents()
bcachefs: kill inode_walker_entry.seen_this_pos
...
