The Renesas RZ/T2H (R9A09G077) SoC includes a Temperature Sensor Unit
(TSU). The device provides real-time temperature measurements for
thermal management, utilizing a single dedicated channel for temperature
sensing.
The TSU loads calibration data via SMC SIP.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251126130356.2768625-9-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move the "interrupt-parent = <&plic>" property from the soc node to the
top node, for consistency with
arch/arm64/boot/dts/renesas/r9a07g043u.dtsi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/97d3d70e42832f4ffa3888bec792b692a7ab700f.1767719409.git.geert+renesas@glider.be
This watchdog can't be used with Linux because the firmware needs it on
R-Car V3H boards. Sadly, it doesn't mark the node as reserved, so this
is added manually here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251215031318.2219-6-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/V2N SoC includes a Thermal Sensor Unit (TSU) block designed
to measure the junction temperature. The device provides real-time
temperature measurements for thermal management, utilizing two dedicated
channels for temperature sensing:
- TSU0, which is located near the DRP-AI block
- TSU1, which is located near the CPU and DRP-AI block
Since TSU1 is physically closer the CPU and the highest temperature
spot, it is used for CPU throttling through a passive trip and cooling
map. TSU0 is configured only with a critical trip.
Add TSU nodes along with thermal zones and keep them enabled in the SoC
DTSI.
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251209091115.8541-4-ovidiu.panait.rb@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/N2H (R9A09G087) SoC has three instances of the DMAC IP.
Add support for them.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251205151254.2970669-7-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/T2H (R9A09G077) SoC has three instances of the DMAC IP.
Add support for them.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251205151254.2970669-6-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/N2H (R9A09G087) SoC has an Interrupt Controller (ICU)
block that routes external interrupts to the GIC's SPIs, with the
ability of level-translation, and can also produce software and
aggregate error interrupts.
Add support for it.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251201112933.488801-5-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/T2H (R9A09G077) SoC has an Interrupt Controller (ICU)
block that routes external interrupts to the GIC's SPIs, with the
ability of level-translation, and can also produce software and
aggregate error interrupts.
Add support for it.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251201112933.488801-4-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
SMARC2 board dtsi is common for multiple SoCs. So Move aliases
to board DTS as SoC may have different IPs for a given alias.
eg: RZ/G3S does not have RSCI interface.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20251129185203.380002-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the NMI connected user pushbutton on the RZ/V2N EVK.
The button is wired to the SoC NMI input and can be used to wake the
system from low-power states.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251125224533.294235-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add node for the Interrupt Control Unit IP found on the Renesas
RZ/V2N SoC, and modify the pinctrl node as its interrupt parent
is the ICU node.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251125224533.294235-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the four SPI controllers on the Renesas RZ/N2H Soc.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251119161434.595677-14-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the four SPI controllers on the Renesas RZ/T2H Soc.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251119161434.595677-13-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the USB3.0 (CH0) host controllers on the RZ/V2N Evaluation Kit.
The CN4 connector on the EVK provides access to the USB3.0 channel.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251119110505.100253-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the USB3.0 (CH0) and USB3.1 (CH1) host controllers on the RZ/V2H
Evaluation Kit. The CN4 stacked connector on the EVK provides access to
both channels, with CH0 corresponding to USB3.0 and CH1 to USB3.1.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251119110505.100253-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
1.8V operation of SD1 requires the jumper to be placed on the correct
pins of a connector on these Evaluation Kits. 1.8V is needed to achieve
the higher rated speeds like SDR104. Add a note about it to make sure no
one else spends too much time figuring this out.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251022073141.1989762-1-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The only core fix is in doc; all the others are in drivers, with the
biggest impacts in libsas being the rollback on error handling and in
ufs coming from a couple of error handling fixes, one causing a crash
if it's activated before scanning and the other fixing W-LUN
resumption.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iLgEABMIAGAWIQTnYEDbdso9F2cI+arnQslM7pishQUCaT4RWBsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMSwyLDImHGphbWVzLmJvdHRvbWxleUBoYW5zZW5wYXJ0bmVy
c2hpcC5jb20ACgkQ50LJTO6YrIVfSgEA23oY0kPjLLkNj4KAjLoWVPmZ/5efKw49
m6YUwfvzTS8BAIq4eFHVecwAM8FAe9NwuOKgO5d9u6epAy6wzBeP2jly
=cpHq
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The only core fix is in doc; all the others are in drivers, with the
biggest impacts in libsas being the rollback on error handling and in
ufs coming from a couple of error handling fixes, one causing a crash
if it's activated before scanning and the other fixing W-LUN
resumption"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: qcom: Fix confusing cleanup.h syntax
scsi: libsas: Add rollback handling when an error occurs
scsi: device_handler: Return error pointer in scsi_dh_attached_handler_name()
scsi: ufs: core: Fix a deadlock in the frequency scaling code
scsi: ufs: core: Fix an error handler crash
scsi: Revert "scsi: libsas: Fix exp-attached device scan after probe failure scanned in again after probe failed"
scsi: ufs: core: Fix RPMB link error by reversing Kconfig dependencies
scsi: qla4xxx: Use time conversion macros
scsi: qla2xxx: Enable/disable IRQD_NO_BALANCING during reset
scsi: ipr: Enable/disable IRQD_NO_BALANCING during reset
scsi: imm: Fix use-after-free bug caused by unfinished delayed work
scsi: target: sbp: Remove KMSG_COMPONENT macro
scsi: core: Correct documentation for scsi_device_quiesce()
scsi: mpi3mr: Prevent duplicate SAS/SATA device entries in channel 1
scsi: target: Reset t_task_cdb pointer in error case
scsi: ufs: core: Fix EH failure after W-LUN resume error
client from Max, a fix that hardens osdmap parsing code from myself
(marked for stable) and a few assorted fixups.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmk8YxITHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi702B/9Mfj0HQSAaWCyMz6GJAv8+1ijVTSbG
nTFeMmipYZhPn188OvWqHsf1cw9rWY0fzenIEW05Tk3YmMvYdeRmCcOkZdeG06xw
um8XxX4L8315E0b98CCpQpVa02ux7XoNtBPjeHccl8PEErJQgQJrQ3Cc/C8kk5U5
a0KlfeVRXYWkOPJva3+wosOu0t9QgJ9ABt5stqcvYDfdkKfvatQMBN3N1nNRKkFH
yhNPv+nRtypSk8jiHhKeeCVmosC0L7MnKuO593vDr761cY5mKrgKFqc2LLlPF6r0
/p13s5SG6X38RUegWCjcK4XRJAzVcR/tyod8LkVVp8d5DC/ptcyy8H+I
=h1gC
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-6.19-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"We have a patch that adds an initial set of tracepoints to the MDS
client from Max, a fix that hardens osdmap parsing code from myself
(marked for stable) and a few assorted fixups"
* tag 'ceph-for-6.19-rc1' of https://github.com/ceph/ceph-client:
rbd: stop selecting CRC32, CRYPTO, and CRYPTO_AES
ceph: stop selecting CRC32, CRYPTO, and CRYPTO_AES
libceph: make decode_pool() more resilient against corrupted osdmaps
libceph: Amend checking to fix `make W=1` build breakage
ceph: Amend checking to fix `make W=1` build breakage
ceph: add trace points to the MDS client
libceph: fix log output race condition in OSD client
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=jbkd
-----END PGP SIGNATURE-----
Merge tag 'smp-urgent-2025-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug fix from Ingo Molnar:
- Fix CPU hotplug callbacks to disable interrupts on UP kernels
* tag 'smp-urgent-2025-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu: Make atomic hotplug callbacks run with interrupts disabled on UP
