The qlink_logging memory region is also used by the modem firmware,
add it to the reserved memories and add it to the MPSS memory regions.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/r/20240123-topic-sm8650-upstream-remoteproc-v7-4-61283f50162f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add Inline Crypto Engine reg and clocks in MMC node and enable CQE
support as Inline Crypto Engine requires CQE to be enabled.
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Link: https://lore.kernel.org/r/20231215095339.3055554-1-quic_viswanat@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add nodes for four WSA8845 speakers. Unlike previous boards like
SM8550-QRD, this board has four speakers spread over two Soundwire buses
instead of two speakers on one bus. Each pair of speakers shares the
reset GPIO thus pinctrl property is only in one of them.
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add Qualcomm Aqstic WCD9385 audio codec on two Soundwire interfaces: RX
and TX.
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add nodes for LPASS Soundwire v2.0.0 controllers. Difference against
SM8550:
1. Update port configs to match reference implementation,
2. LPASS TLMM GPIO14 is not used as WCD_SR_TX_DATA2 pin but as GPIO
(camera).
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the Low Power Audio SubSystem (LPASS) / ADSP audio codec macros on
Qualcomm SM8650. The nodes are exactly the same as on SM8550 and
SM8650.
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the Low Power Audio SubSystem Low Power Island (LPASS LPI) pin
controller device node as part of audio subsystem in Qualcomm X1E80100
SoC.
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231212125632.54021-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the ADSP Generic Packet Router (GPR) device node as part of audio
subsystem in Qualcomm X1E80100 SoC.
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231212125632.54021-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the required nodes to support display on X1E80100.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-8-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add nodes for PCIe 4 and 6 controllers and their PHYs for X1E80100 platform.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-7-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add nodes for all USB controllers and their PHYs for X1E80100 platform.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-6-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add ADSP and CDSP remoteproc nodes on X1E80100 platforms.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-4-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
SMP2P is used for interrupting and being interrupted about remoteproc
state changes related to the audio, compute and sensor subsystems.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-2-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the IPCC node, used to send and receive IPC signals with
remoteprocs.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-1-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add bindings documentation for the X1E80100 Camera Clock Controller.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240202-x1e80100-clock-controllers-v4-5-7fb08c861c7c@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The block is the same between these platforms, at least from devicetree
point of view. So drop the dedicated schema and use the SM8550 one instead.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240202-x1e80100-clock-controllers-v4-1-7fb08c861c7c@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
New memory map layout changes (by Qualcomm firmware) have brought
in updates to base addresses and/or size for different memory regions
like cpcucp_fw, tz-stat, and also introduces new memory regions for
resource manager firmware. The updated memory map also fixes existing
issues pertaining to boot up failure while running memtest, thus
improving stability.
This change brings in these corresponding memory map updates to the
device tree for SA8775P SoC platform, which currently is in its
development stage.
Signed-off-by: Ninad Naik <quic_ninanaik@quicinc.com>
Tested-by: Eric Chanudet <echanude@redhat.com> # sa8775p-ride
Link: https://lore.kernel.org/r/20240125055134.7015-1-quic_ninanaik@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add definition for three LEDs to make sure they can
be enabled base on QCOM LPG LED driver.
Signed-off-by: Hui Liu <quic_huliu@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-lpg-v6-1-f879cecbce69@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the necessary nodes to support the USB-C Altmode path by
adding the following
- WCD939x USBSS Mux I2C device
- nb7vpq904m Redriver I2C device
- Port/Endpoint graph links bettween PMIC-Glink, Mux, Redriver and USB PHY nodes.
WCD939x USBSS port 2 Path to Codec will be added later when Audio support
is added.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240123-topic-sm8650-upstream-altmode-v3-1-300a5ac80e1e@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a device tree for the Xiaomi Redmi Note 9S (curtana) phone, based on
sm7125-xiaomi-common.dtsi.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Joe Mason <buddyjojo06@outlook.com>
Signed-off-by: David Wronek <davidwronek@gmail.com>
Link: https://lore.kernel.org/r/20240121-sm7125-upstream-v4-8-f7d1212c8ebb@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the Xiaomi Redmi Note 9S (curtana) smartphone, which is based
on the Qualcomm SM7125 SoC.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David Wronek <davidwronek@gmail.com>
Link: https://lore.kernel.org/r/20240121-sm7125-upstream-v4-4-f7d1212c8ebb@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Inforce IFC6560 board actually has USB SS lines routed to the USB-C
connector. Enable USB 3.0 PHY and SS mode for the USB3 host.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240116-sdm660-usb3-support-v1-4-2fbd683aea77@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Define USB3 QMP PHY presend on the SDM630 / SDM660 platforms. Enable it by
default in the USB3 host, but (for compatibility), force USB 2.0 mode
for all defined boards. The boards should opt-in to enable USB 3.0
support.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240116-sdm660-usb3-support-v1-3-2fbd683aea77@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add CAMSS block definition for sc8280xp.
This drop contains definitions for the following components on sc8280xp:
VFE * 4
VFE Lite * 4
CSID * 4
CSIPHY * 4
This dtsi definition has been developed and validated on a Lenovo X13s
laptop.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240111-linux-next-24-01-02-sc8280xp-camss-core-dtsi-v4-4-cdd5c57ff1dc@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
sc8280xp has four Camera Control Interface (CCI) blocks which pinout to
two I2C master controllers for each CCI.
The CCI I2C pins are not muxed so we define them in the dtsi.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240111-linux-next-24-01-02-sc8280xp-camss-core-dtsi-v4-3-cdd5c57ff1dc@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
With the necessary support in place for supplying VDD_GFX from the
MAX20411 regulator, enable the GPU clock controller, GMU, Adreno SMMU
and the GPU on the SA8295P ADP.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240125-sa8295p-gpu-v4-7-7011c2a63037@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SA8295P ADP has a MAX20411 LDO regulator on I2C 12, supplying the
VDD_GFX pads. Enable the bus and add the maxim,max20411 device on the
bus.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240125-sa8295p-gpu-v4-6-7011c2a63037@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SA8295P and SA8540P uses an external regulator (max20411), and
gfx.lvl is not provided by rpmh. Drop the power-domains property of the
gpucc node to reflect this.
Fixes: eec51ab2fd ("arm64: dts: qcom: sc8280xp: Add GPU related nodes")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240125-sa8295p-gpu-v4-5-7011c2a63037@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Specify the file name for the squashed/non-split firmware with the .mbn
extension instead of the split .mdt. The kernel can load both but the
squashed version is preferred in dts nowadays.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240110-fp4-mbn-v1-1-45e7e33b1834@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
It seems, the only actual mentions of PM2250 can be found are related to
the Qualcomm RB1 platform. However even RB1 schematics use PM4125 as a
PMIC name. Rename PM2250 to PM4125 to follow the documentation.
Note, this doesn't change the compatible strings. There was a previous
argument regarding renaming of compat strings.
Fixes: c309b9a540 ("arm64: dts: qcom: Add initial PM2250 device tree")
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240128-pm2250-pm4125-rename-v2-2-d51987e9f83a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Via the PMIC GLINK driver we can get info about fuel gauge, charger and
USB connector events. Add the node to the dts and configure USB so that
role switching works.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231220-fp5-pmic-glink-v1-3-2a1f8e3c661c@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Make it easier to understand what the reg in those nodes is by using the
constants provided by qcom,q6dsp-lpass-ports.h.
Name nodes according to dt-binding expectations.
Fix for
```
arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dtb: service@4: dais: Unevaluated properties are not allowed ('qi2s@22', 'qi2s@23' were unexpected)
```
Fixes: b7b7342868 ("arm64: dts: qcom: sdm845-oneplus-*: add audio devices")
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20231229200245.259689-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
It seems we also need to reserve a region of 81 MiB called "removed_mem"
otherwise we can easily hit the following error with higher RAM usage:
[ 1467.809274] Internal error: synchronous external abort: 0000000096000010 [#2] SMP
Fixes: eee9602ad6 ("arm64: dts: qcom: qcm6490: Add device-tree for Fairphone 5")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231229-fp5-reserved-mem-v1-1-87bb818f1397@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
When the properties num-channels & qcom,num-ees are not specified, the
driver tries to read the values from registers, but this read fails and
resets the device if the interconnect from the qcom,qce node is not
already active when that happens.
Add the static properties to not touch any registers during probe, the
rest of the time when the BAM is used by QCE then the interconnect will
be active already.
Fixes: d488f903a8 ("arm64: dts: qcom: sc7280: add QCrypto nodes")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231229-sc7280-cryptobam-fixup-v1-1-bd8f68589b80@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add changes to support safety IRQ handling
support for ethernet.
Signed-off-by: Suraj Jaiswal <quic_jsuraj@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240110111649.2256450-3-quic_jsuraj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
