commit 3bacc10cd4 upstream.
Fix clamp_align() used in v4l_bound_align_image() to prevent overflow
when passed large value like UINT32_MAX.
In the current implementation:
clamp_align(UINT32_MAX, 8, 8192, 3)
returns 8, because in line:
x = (x + (1 << (align - 1))) & mask;
x overflows to (-1 + 4) & 0x7 = 3, while expected value is 8192.
v4l_bound_align_image() is heavily used in VIDIOC_S_FMT and
VIDIOC_SUBDEV_S_FMT ioctls handlers, and documentation of the latter
explicitly states that:
"The modified format should be as close as possible to the original
request."
-- http://linuxtv.org/downloads/v4l-dvb-apis/vidioc-subdev-g-fmt.html
Thus one would expect, that passing UINT32_MAX as format width and
height will result in setting maximum possible resolution for the
device. Particularly, when the driver doesn't support
VIDIOC_ENUM_FRAMESIZES ioctl, which is common in the codebase.
Fixes changeset: b0d3159be9
Signed-off-by: Maciej Matraszek <m.matraszek@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e351943b08 upstream.
The userspace drm.h include doesn't prefix the drm directory. This can lead
to compile failures as /usr/include/drm/ isn't in the standard gcc include
paths. Fix it to be <drm/drm.h>, which matches the rest of the driver drm
header files that get installed into /usr/include/drm.
Red Hat Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1138759
Fixes: 1d7a5cbf8f
Reported-by: Jeffrey Bastian <jbastian@redhat.com>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c479f4383e upstream.
sg_alloc_table_from_pages() can build us a table with coalesced ranges which
means we need to iterate over pages and not sg table entries when releasing
page references.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Barbalho, Rafael" <rafael.barbalho@intel.com>
Tested-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Remove unused local variable sg.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit b485a7005f upstream.
nv92 hardware has only 16 interrupt lines, while nv94 and later
has 32. Accessing 0xe0c{0,4} registers on nv92 can lead to incorrect
PDISP setup. This is a regression introduced with
commit 9d0f5ec9ee0fd5dc5fc1cc2cf559286431e406e3
Author: Ben Skeggs <bskeggs@redhat.com>
Date: Mon May 12 15:22:42 2014 +1000
gpio: split g92 class from nv50
Reported-by: estece on #nouveau
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 1e99cfa8de upstream.
The translation from the X driver to the KMS one typo'ed a couple
of array indices, causing the HW cursor to look weird (blocky with
leaking edge colors). This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9ff84a1730 upstream.
Without this the aux port does not get detected, and consequently the
touchpad will not work.
https://bugzilla.redhat.com/show_bug.cgi?id=1110011
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit aa97240995 upstream.
Unfortunately, ForcePad capability is not actually exported over PS/2, so
we have to resort to DMI checks.
Reported-by: Nicole Faerber <nicole.faerber@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f74a289b94 upstream.
The framebuffer code uses the current background color to fill the border
when switching consoles, however, this results in inconsistent behavior.
For example:
- start Midnigh Commander
- the border is black
- switch to another console and switch back
- the border is cyan
- type something into the command line in mc
- the border is cyan
- switch to another console and switch back
- the border is black
- press F9 to go to menu
- the border is black
- switch to another console and switch back
- the border is dark blue
When switching to a console with Midnight Commander, the border is random
color that was left selected by the slang subsystem.
This patch fixes this inconsistency by always using black as the
background color when switching consoles.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5b789da8a7 upstream.
The function bitcpy_rev has a bug that may result in screen corruption.
The bug happens under these conditions:
* the end of the destination area of a copy operation is aligned on a long
word boundary
* the end of the source area is not aligned on a long word boundary
* we are copying more than one long word
In this case, the variable shift is non-zero and the variable first is
zero. The statements FB_WRITEL(comp(d0, FB_READL(dst), first), dst) reads
the last long word of the destination and writes it back unchanged
(because first is zero). Correctly, we should write the variable d0 to the
last word of the destination in this case.
This patch fixes the bug by introducing and extra test if first is zero.
The patch also removes the references to fb_memmove in the code that is
commented out because fb_memmove was removed from framebuffer subsystem.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d3051b489a upstream.
A panic was seen in the following sitation.
There are two threads running on the system. The first thread is a system
monitoring thread that is reading /proc/modules. The second thread is
loading and unloading a module (in this example I'm using my simple
dummy-module.ko). Note, in the "real world" this occurred with the qlogic
driver module.
When doing this, the following panic occurred:
------------[ cut here ]------------
kernel BUG at kernel/module.c:3739!
invalid opcode: 0000 [#1] SMP
Modules linked in: binfmt_misc sg nfsv3 rpcsec_gss_krb5 nfsv4 dns_resolver nfs fscache intel_powerclamp coretemp kvm_intel kvm crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel lrw igb gf128mul glue_helper iTCO_wdt iTCO_vendor_support ablk_helper ptp sb_edac cryptd pps_core edac_core shpchp i2c_i801 pcspkr wmi lpc_ich ioatdma mfd_core dca ipmi_si nfsd ipmi_msghandler auth_rpcgss nfs_acl lockd sunrpc xfs libcrc32c sr_mod cdrom sd_mod crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit drm_kms_helper ttm isci drm libsas ahci libahci scsi_transport_sas libata i2c_core dm_mirror dm_region_hash dm_log dm_mod [last unloaded: dummy_module]
CPU: 37 PID: 186343 Comm: cat Tainted: GF O-------------- 3.10.0+ #7
Hardware name: Intel Corporation S2600CP/S2600CP, BIOS RMLSDP.86I.00.29.D696.1311111329 11/11/2013
task: ffff8807fd2d8000 ti: ffff88080fa7c000 task.ti: ffff88080fa7c000
RIP: 0010:[<ffffffff810d64c5>] [<ffffffff810d64c5>] module_flags+0xb5/0xc0
RSP: 0018:ffff88080fa7fe18 EFLAGS: 00010246
RAX: 0000000000000003 RBX: ffffffffa03b5200 RCX: 0000000000000000
RDX: 0000000000001000 RSI: ffff88080fa7fe38 RDI: ffffffffa03b5000
RBP: ffff88080fa7fe28 R08: 0000000000000010 R09: 0000000000000000
R10: 0000000000000000 R11: 000000000000000f R12: ffffffffa03b5000
R13: ffffffffa03b5008 R14: ffffffffa03b5200 R15: ffffffffa03b5000
FS: 00007f6ae57ef740(0000) GS:ffff88101e7a0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000404f70 CR3: 0000000ffed48000 CR4: 00000000001407e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffffffffa03b5200 ffff8810101e4800 ffff88080fa7fe70 ffffffff810d666c
ffff88081e807300 000000002e0f2fbf 0000000000000000 ffff88100f257b00
ffffffffa03b5008 ffff88080fa7ff48 ffff8810101e4800 ffff88080fa7fee0
Call Trace:
[<ffffffff810d666c>] m_show+0x19c/0x1e0
[<ffffffff811e4d7e>] seq_read+0x16e/0x3b0
[<ffffffff812281ed>] proc_reg_read+0x3d/0x80
[<ffffffff811c0f2c>] vfs_read+0x9c/0x170
[<ffffffff811c1a58>] SyS_read+0x58/0xb0
[<ffffffff81605829>] system_call_fastpath+0x16/0x1b
Code: 48 63 c2 83 c2 01 c6 04 03 29 48 63 d2 eb d9 0f 1f 80 00 00 00 00 48 63 d2 c6 04 13 2d 41 8b 0c 24 8d 50 02 83 f9 01 75 b2 eb cb <0f> 0b 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41
RIP [<ffffffff810d64c5>] module_flags+0xb5/0xc0
RSP <ffff88080fa7fe18>
Consider the two processes running on the system.
CPU 0 (/proc/modules reader)
CPU 1 (loading/unloading module)
CPU 0 opens /proc/modules, and starts displaying data for each module by
traversing the modules list via fs/seq_file.c:seq_open() and
fs/seq_file.c:seq_read(). For each module in the modules list, seq_read
does
op->start() <-- this is a pointer to m_start()
op->show() <- this is a pointer to m_show()
op->stop() <-- this is a pointer to m_stop()
The m_start(), m_show(), and m_stop() module functions are defined in
kernel/module.c. The m_start() and m_stop() functions acquire and release
the module_mutex respectively.
ie) When reading /proc/modules, the module_mutex is acquired and released
for each module.
m_show() is called with the module_mutex held. It accesses the module
struct data and attempts to write out module data. It is in this code
path that the above BUG_ON() warning is encountered, specifically m_show()
calls
static char *module_flags(struct module *mod, char *buf)
{
int bx = 0;
BUG_ON(mod->state == MODULE_STATE_UNFORMED);
...
The other thread, CPU 1, in unloading the module calls the syscall
delete_module() defined in kernel/module.c. The module_mutex is acquired
for a short time, and then released. free_module() is called without the
module_mutex. free_module() then sets mod->state = MODULE_STATE_UNFORMED,
also without the module_mutex. Some additional code is called and then the
module_mutex is reacquired to remove the module from the modules list:
/* Now we can delete it from the lists */
mutex_lock(&module_mutex);
stop_machine(__unlink_module, mod, NULL);
mutex_unlock(&module_mutex);
This is the sequence of events that leads to the panic.
CPU 1 is removing dummy_module via delete_module(). It acquires the
module_mutex, and then releases it. CPU 1 has NOT set dummy_module->state to
MODULE_STATE_UNFORMED yet.
CPU 0, which is reading the /proc/modules, acquires the module_mutex and
acquires a pointer to the dummy_module which is still in the modules list.
CPU 0 calls m_show for dummy_module. The check in m_show() for
MODULE_STATE_UNFORMED passed for dummy_module even though it is being
torn down.
Meanwhile CPU 1, which has been continuing to remove dummy_module without
holding the module_mutex, now calls free_module() and sets
dummy_module->state to MODULE_STATE_UNFORMED.
CPU 0 now calls module_flags() with dummy_module and ...
static char *module_flags(struct module *mod, char *buf)
{
int bx = 0;
BUG_ON(mod->state == MODULE_STATE_UNFORMED);
and BOOM.
Acquire and release the module_mutex lock around the setting of
MODULE_STATE_UNFORMED in the teardown path, which should resolve the
problem.
Testing: In the unpatched kernel I can panic the system within 1 minute by
doing
while (true) do insmod dummy_module.ko; rmmod dummy_module.ko; done
and
while (true) do cat /proc/modules; done
in separate terminals.
In the patched kernel I was able to run just over one hour without seeing
any issues. I also verified the output of panic via sysrq-c and the output
of /proc/modules looks correct for all three states for the dummy_module.
dummy_module 12661 0 - Unloading 0xffffffffa03a5000 (OE-)
dummy_module 12661 0 - Live 0xffffffffa03bb000 (OE)
dummy_module 14015 1 - Loading 0xffffffffa03a5000 (OE+)
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 56ec16cb1e upstream.
If cn_add_callback() fails in dm_ulog_tfr_init(), it does not
deallocate prealloced memory but calls cn_del_callback().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit b8839b8c55 upstream.
The math in both blk_stack_limits() and queue_limit_alignment_offset()
assume that a block device's io_min (aka minimum_io_size) is always a
power-of-2. Fix the math such that it works for non-power-of-2 io_min.
This issue (of alignment_offset != 0) became apparent when testing
dm-thinp with a thinp blocksize that matches a RAID6 stripesize of
1280K. Commit fdfb4c8c1 ("dm thin: set minimum_io_size to pool's data
block size") unlocked the potential for alignment_offset != 0 due to
the dm-thin-pool's io_min possibly being a non-power-of-2.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 82cfb90bc9 upstream.
Commit 98683650 "Merge branch 'drbd-8.4_ed6' into
for-3.8-drivers-drbd-8.4_ed6" switches to the new augment API, but the
new API requires that the tree is augmented before rb_insert_augmented()
is called, which is missing.
So we add the augment-code to drbd_insert_interval() when it travels the
tree up to down before rb_insert_augmented(). See the example in
include/linux/interval_tree_generic.h or Documentation/rbtree.txt.
drbd_insert_interval() may cancel the insertion when traveling, in this
case, the just added augment-code does nothing before cancel since the
@this node is already in the subtrees in this case.
CC: Michel Lespinasse <walken@google.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0e825862f3 upstream.
When __scan frees the required number of buffer entries that the
shrinker requested (nr_to_scan becomes zero) it must return. Before
this fix the __scan code exited only the inner loop and continued in the
outer loop -- which could result in reduced performance due to extra
buffers being freed (e.g. unnecessarily evicted thinp metadata needing
to be synchronously re-read into bufio's cache).
Also, move dm_bufio_cond_resched to __scan's inner loop, so that
iterating the bufio client's lru lists doesn't result in scheduling
latency.
Reported-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit eb76faf53b upstream.
The 'last_accessed' member of the dm_buffer structure was only set when
the the buffer was created. This led to each buffer being discarded
after dm_bufio_max_age time even if it was used recently. In practice
this resulted in all thinp metadata being evicted soon after being read
-- this is particularly problematic for metadata intensive workloads
like multithreaded small random IO.
'last_accessed' is now updated each time the buffer is moved to the head
of the LRU list, so the buffer is now properly discarded if it was not
used in dm_bufio_max_age time.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit abab13b5c4 upstream.
We currently divide the queue depth by 4 as our batch wakeup
count, but we split the wakeups over BT_WAIT_QUEUES number of
wait queues. This defaults to 8. If the product of the resulting
batch wake count and BT_WAIT_QUEUES is higher than the device
queue depth, we can get into a situation where a task goes to
sleep waiting for a request, but never gets woken up.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Fixes: 4bb659b156
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 12ea729645 upstream.
blkback does not unmap persistent grants when frontend goes to Closed
state (e.g. when blkfront module is being removed). This leads to the
following in guest's dmesg:
[ 343.243825] xen:grant_table: WARNING: g.e. 0x445 still in use!
[ 343.243825] xen:grant_table: WARNING: g.e. 0x42a still in use!
...
When load module -> use device -> unload module sequence is performed multiple times
it is possible to hit BUG() condition in blkfront module:
[ 343.243825] kernel BUG at drivers/block/xen-blkfront.c:954!
[ 343.243825] invalid opcode: 0000 [#1] SMP
[ 343.243825] Modules linked in: xen_blkfront(-) ata_generic pata_acpi [last unloaded: xen_blkfront]
...
[ 343.243825] Call Trace:
[ 343.243825] [<ffffffff814111ef>] ? unregister_xenbus_watch+0x16f/0x1e0
[ 343.243825] [<ffffffffa0016fbf>] blkfront_remove+0x3f/0x140 [xen_blkfront]
...
[ 343.243825] RIP [<ffffffffa0016aae>] blkif_free+0x34e/0x360 [xen_blkfront]
[ 343.243825] RSP <ffff88001eb8fdc0>
We don't need to keep these grants if we're disconnecting as frontend might already
forgot about them. Solve the issue by moving xen_blkbk_free_caches() call from
xen_blkif_free() to xen_blkif_disconnect().
Now we can see the following:
[ 928.590893] xen:grant_table: WARNING: g.e. 0x587 still in use!
[ 928.591861] xen:grant_table: WARNING: g.e. 0x372 still in use!
...
[ 929.592146] xen:grant_table: freeing g.e. 0x587
[ 929.597174] xen:grant_table: freeing g.e. 0x372
...
Backend does not keep persistent grants any more, reconnect works fine.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6fbc198cf6 upstream.
On restore, virtio pci does the following:
+ set features
+ init vqs etc - device can be used at this point!
+ set ACKNOWLEDGE,DRIVER and DRIVER_OK status bits
This is in violation of the virtio spec, which
requires the following order:
- ACKNOWLEDGE
- DRIVER
- init vqs
- DRIVER_OK
This behaviour will break with hypervisors that assume spec compliant
behaviour. It seems like a good idea to have this patch applied to
stable branches to reduce the support butden for the hypervisors.
Cc: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 923190d32d upstream.
sb_finish_set_opts() can race with inode_free_security()
when initializing inode security structures for inodes
created prior to initial policy load or by the filesystem
during ->mount(). This appears to have always been
a possible race, but commit 3dc91d4 ("SELinux: Fix possible
NULL pointer dereference in selinux_inode_permission()")
made it more evident by immediately reusing the unioned
list/rcu element of the inode security structure for call_rcu()
upon an inode_free_security(). But the underlying issue
was already present before that commit as a possible use-after-free
of isec.
Shivnandan Kumar reported the list corruption and proposed
a patch to split the list and rcu elements out of the union
as separate fields of the inode_security_struct so that setting
the rcu element would not affect the list element. However,
this would merely hide the issue and not truly fix the code.
This patch instead moves up the deletion of the list entry
prior to dropping the sbsec->isec_lock initially. Then,
if the inode is dropped subsequently, there will be no further
references to the isec.
Reported-by: Shivnandan Kumar <shivnandan.k@samsung.com>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5152970538 upstream.
pci_enable_msi() can return failure with both positive and negative
integers -- it returns 0 for success -- but is only tested here for
"if (ret < 0)". This causes us to try to use MSI on the RTS5249 SD
reader in the Dell XPS 11 when enabling MSI failed, causing:
[ 1.737110] rtsx_pci: probe of 0000:05:00.0 failed with error -110
Reported-by: D. Jared Dominguez <Jared_Dominguez@Dell.com>
Tested-by: D. Jared Dominguez <Jared_Dominguez@Dell.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6a71f38dd8 upstream.
In the resume path, the ADC invokes am335x_tsc_se_set_cache() with 0 as
the steps argument if continous mode is not in use. This in turn disables
all steps and so the TSC is not working until one ADC sampling is
performed.
This patch fixes it by writing the current cached mask instead of the
passed steps.
Fixes: 7ca6740cd1 ("mfd: input: iio: ti_amm335x: Rework TSC/ADCA
synchronization")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6ac734d224 upstream.
After enabling and disabling ADC continuous mode via sysfs, ts_print_raw
fails to return any data. This is because when ADC is configured for
continuous mode, it disables touch screen steps.These steps are not
re-enabled when ADC continuous mode is disabled. Therefore existing values
of REG_SE needs to be cached before enabling continuous mode and
disabling touch screen steps and enabling ADC steps. The cached value
are to be restored to REG_SE once ADC is disabled.
Fixes: 7ca6740cd1 ("mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 48e9a6c1f5 upstream.
The call to topology_init is too late for the set_sched_topology call.
The initial scheduling domain structure has already been established
with default topology array. Use the smp_cpus_done() call to get the
s390 specific topology array registered early enough.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2a2361228c upstream.
Starting with Linux 3.12 processes get stuck in D state forever in
UserModeLinux under sync heavy workloads. This bug was introduced by
commit 805f11a0d5 (um: ubd: Add REQ_FLUSH suppport).
Fix bug by adding a check if FLUSH request was successfully submitted to
the I/O thread and keeping the FLUSH request on the request queue on
submission failures.
Fixes: 805f11a0d5 (um: ubd: Add REQ_FLUSH suppport)
Signed-off-by: Thorsten Knabe <linux@thorsten-knabe.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 66339c31bc upstream.
dl_bw_of() dereferences rq->rd which has to have RCU read lock held.
Probability of use-after-free isn't zero here.
Also add lockdep assert into dl_bw_cpus().
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140922183624.11015.71558.stgit@localhost
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f9865f06f7 upstream.
Commit f363e45fd1 ("net/ceph: make ceph_msgr_wq non-reentrant")
effectively removed WQ_MEM_RECLAIM flag from ceph_msgr_wq. This is
wrong - libceph is very much a memory reclaim path, so restore it.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Tested-by: Micha Krause <micha@krausam.de>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 24dff96a37 upstream.
we used to check for "nobody else could start doing anything with
that opened file" by checking that refcount was 2 or less - one
for descriptor table and one we'd acquired in fget() on the way to
wherever we are. That was race-prone (somebody else might have
had a reference to descriptor table and do fget() just as we'd
been checking) and it had become flat-out incorrect back when
we switched to fget_light() on those codepaths - unlike fget(),
it doesn't grab an extra reference unless the descriptor table
is shared. The same change allowed a race-free check, though -
we are safe exactly when refcount is less than 2.
It was a long time ago; pre-2.6.12 for ioctl() (the codepath leading
to ppp one) and 2.6.17 for sendmsg() (netlink one). OTOH,
netlink hadn't grown that check until 3.9 and ppp used to live
in drivers/net, not drivers/net/ppp until 3.1. The bug existed
well before that, though, and the same fix used to apply in old
location of file.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 99358a1ca5 upstream.
schedule_delayed_work() happening when the work is already pending is
a cheap no-op. Don't bother with ->wbuf_queued logics - it's both
broken (cancelling ->wbuf_dwork leaves it set, as spotted by Jeff Harris)
and pointless. It's cheaper to let schedule_delayed_work() handle that
case.
Reported-by: Jeff Harris <jefftharris@gmail.com>
Tested-by: Jeff Harris <jefftharris@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6d13f69444 upstream.
AFAICS, prepend_name() is broken on SMP alpha. Disclaimer: I don't have
SMP alpha boxen to reproduce it on. However, it really looks like the race
is real.
CPU1: d_path() on /mnt/ramfs/<255-character>/foo
CPU2: mv /mnt/ramfs/<255-character> /mnt/ramfs/<63-character>
CPU2 does d_alloc(), which allocates an external name, stores the name there
including terminating NUL, does smp_wmb() and stores its address in
dentry->d_name.name. It proceeds to d_add(dentry, NULL) and d_move()
old dentry over to that. ->d_name.name value ends up in that dentry.
In the meanwhile, CPU1 gets to prepend_name() for that dentry. It fetches
->d_name.name and ->d_name.len; the former ends up pointing to new name
(64-byte kmalloc'ed array), the latter - 255 (length of the old name).
Nothing to force the ordering there, and normally that would be OK, since we'd
run into the terminating NUL and stop. Except that it's alpha, and we'd need
a data dependency barrier to guarantee that we see that store of NUL
__d_alloc() has done. In a similar situation dentry_cmp() would survive; it
does explicit smp_read_barrier_depends() after fetching ->d_name.name.
prepend_name() doesn't and it risks walking past the end of kmalloc'ed object
and possibly oops due to taking a page fault in kernel mode.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3dcbad52cf upstream.
Unless an LSM labels a file during d_instantiate(), newly created
files are not labeled with an initial security.evm xattr, until
the file closes. EVM, before allowing a protected, security xattr
to be written, verifies the existing 'security.evm' value is good.
For newly created files without a security.evm label, this
verification prevents writing any protected, security xattrs,
until the file closes.
Following is the example when this happens:
fd = open("foo", O_CREAT | O_WRONLY, 0644);
setxattr("foo", "security.SMACK64", value, sizeof(value), 0);
close(fd);
While INTEGRITY_NOXATTRS status is handled in other places, such
as evm_inode_setattr(), it does not handle it in all cases in
evm_protect_xattr(). By limiting the use of INTEGRITY_NOXATTRS to
newly created files, we can now allow setting "protected" xattrs.
Changelog:
- limit the use of INTEGRITY_NOXATTRS to IMA identified new files
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 211de6eba8 upstream.
The idiot who did 4a1c0f262f ("perf: Fix lockdep warning on process exit")
forgot to pay attention and fix all similar cases. Do so now.
In particular, unclone_ctx() must be called while holding ctx->lock,
therefore all such sites are broken for the same reason. Pull the
put_ctx() call out from under ctx->lock.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Probably-also-reported-by: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 4a1c0f262f ("perf: Fix lockdep warning on process exit")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Cong Wang <cwang@twopensource.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140930172308.GI4241@worktop.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit df24fb859a upstream.
Add preempt_disable() + preempt_enable() around math_state_restore() in
__restore_xstate_sig(). Otherwise __switch_to() after __thread_fpu_begin()
can overwrite fpu->state we are going to restore.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20140902175717.GA21649@redhat.com
Reviewed-by: Suresh Siddha <sbsiddha@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0e6d3112a4 upstream.
It is currently possible to execve() an x32 executable on an x86_64
kernel that has only ia32 compat enabled. However all its syscalls
will fail, even _exit(). This usually causes it to segfault.
Change the ELF compat architecture check so that x32 executables are
rejected if we don't support the x32 ABI.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Link: http://lkml.kernel.org/r/1410120305.6822.9.camel@decadent.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ba29e721eb upstream.
Hu (hujianyang <hujianyang@huawei.com>) discovered an issue in the
'empty_log_bytes()' function, which calculates how many bytes are left in the
log:
"
If 'c->lhead_lnum + 1 == c->ltail_lnum' and 'c->lhead_offs == c->leb_size', 'h'
would equalent to 't' and 'empty_log_bytes()' would return 'c->log_bytes'
instead of 0.
"
At this point it is not clear what would be the consequences of this, and
whether this may lead to any problems, but this patch addresses the issue just
in case.
Tested-by: hujianyang <hujianyang@huawei.com>
Reported-by: hujianyang <hujianyang@huawei.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 052c28073f upstream.
Hu (hujianyang@huawei.com) discovered a race condition which may lead to a
situation when UBIFS is unable to mount the file-system after an unclean
reboot. The problem is theoretical, though.
In UBIFS, we have the log, which basically a set of LEBs in a certain area. The
log has the tail and the head.
Every time user writes data to the file-system, the UBIFS journal grows, and
the log grows as well, because we append new reference nodes to the head of the
log. So the head moves forward all the time, while the log tail stays at the
same position.
At any time, the UBIFS master node points to the tail of the log. When we mount
the file-system, we scan the log, and we always start from its tail, because
this is where the master node points to. The only occasion when the tail of the
log changes is the commit operation.
The commit operation has 2 phases - "commit start" and "commit end". The former
is relatively short, and does not involve much I/O. During this phase we mostly
just build various in-memory lists of the things which have to be written to
the flash media during "commit end" phase.
During the commit start phase, what we do is we "clean" the log. Indeed, the
commit operation will index all the data in the journal, so the entire journal
"disappears", and therefore the data in the log become unneeded. So we just
move the head of the log to the next LEB, and write the CS node there. This LEB
will be the tail of the new log when the commit operation finishes.
When the "commit start" phase finishes, users may write more data to the
file-system, in parallel with the ongoing "commit end" operation. At this point
the log tail was not changed yet, it is the same as it had been before we
started the commit. The log head keeps moving forward, though.
The commit operation now needs to write the new master node, and the new master
node should point to the new log tail. After this the LEBs between the old log
tail and the new log tail can be unmapped and re-used again.
And here is the possible problem. We do 2 operations: (a) We first update the
log tail position in memory (see 'ubifs_log_end_commit()'). (b) And then we
write the master node (see the big lock of code in 'do_commit()').
But nothing prevents the log head from moving forward between (a) and (b), and
the log head may "wrap" now to the old log tail. And when the "wrap" happens,
the contends of the log tail gets erased. Now a power cut happens and we are in
trouble. We end up with the old master node pointing to the old tail, which was
erased. And replay fails because it expects the master node to point to the
correct log tail at all times.
This patch merges the abovementioned (a) and (b) operations by moving the master
node change code to the 'ubifs_log_end_commit()' function, so that it runs with
the log mutex locked, which will prevent the log from being changed benween
operations (a) and (b).
Reported-by: hujianyang <hujianyang@huawei.com>
Tested-by: hujianyang <hujianyang@huawei.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 07e19dff63 upstream.
The 'mst_mutex' is not needed since because 'ubifs_write_master()' is only
called on the mount path and commit path. The mount path is sequential and
there is no parallelism, and the commit path is also serialized - there is only
one commit going on at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 475d0db742 upstream.
total_objects could be 0 and is used as a denom.
While total_objects is a "long", total_objects == 0 unlikely happens for
3.12 and later kernels because 32-bit architectures would not be able to
hold (1 << 32) objects. However, total_objects == 0 may happen for kernels
between 3.1 and 3.11 because total_objects in prune_super() was an "int"
and (e.g.) x86_64 architecture might be able to hold (1 << 32) objects.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c2ca0fcd20 upstream.
This patch makes it possible to kill a process looping in
cont_expand_zero. A process may spend a lot of time in this function, so
it is desirable to be able to kill it.
It happened to me that I wanted to copy a piece data from the disk to a
file. By mistake, I used the "seek" parameter to dd instead of "skip". Due
to the "seek" parameter, dd attempted to extend the file and became stuck
doing so - the only possibility was to reset the machine or wait many
hours until the filesystem runs out of space and cont_expand_zero fails.
We need this patch to be able to terminate the process.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d1419d50c1 upstream.
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
Fixes: ff984e57d3 ("mmc: Add realtek pcie sdmmc host driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d4d1144908 upstream.
As soon as the CD IRQ is requested, it can trigger, since it's an
externally controlled event. If it does, delayed_work host->detect will
be scheduled.
Many host controller probe()s are roughly structured as:
*_probe() {
host = sdhci_pltfm_init();
mmc_of_parse(host->mmc);
rc = sdhci_add_host(host);
if (rc) {
sdhci_pltfm_free();
return rc;
}
In 3.17, CD IRQs can are enabled quite early via *_probe() ->
mmc_of_parse() -> mmc_gpio_request_cd() -> mmc_gpiod_request_cd_irq().
Note that in linux-next, mmc_of_parse() calls mmc_gpio*d*_request_cd()
rather than mmc_gpio_request_cd(), and mmc_gpio*d*_request_cd() doesn't
call mmc_gpiod_request_cd_irq(). However, this issue still exists if
mmc_gpio_request_cd() is called directly before mmc_start_host().
sdhci_add_host() may fail part way through (e.g. due to deferred
probe for a vmmc regulator), and sdhci_pltfm_free() does nothing to
unrequest the CD IRQ nor cancel the delayed_work. sdhci_pltfm_free() is
coded to assume that if sdhci_add_host() failed, then the delayed_work
cannot (or should not) have been triggered.
This can lead to the following with CONFIG_DEBUG_OBJECTS_* enabled, when
kfree(host) is eventually called inside sdhci_pltfm_free():
WARNING: CPU: 2 PID: 6 at lib/debugobjects.c:263 debug_print_object+0x8c/0xb4()
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x18
The object being complained about is host->detect.
There's no need to request the CD IRQ so early; mmc_start_host() already
requests it. For most SDHCI hosts at least, the typical call path that
does this is: *_probe() -> sdhci_add_host() -> mmc_add_host() ->
mmc_start_host(). Therefore, remove the call to mmc_gpiod_request_cd_irq()
from mmc_gpio_request_cd(). This also matches mmc_gpio*d*_request_cd(),
which already doesn't call mmc_gpiod_request_cd_irq().
However, some host controller drivers call mmc_gpio_request_cd() after
mmc_start_host() has already been called, and assume that this will also
call mmc_gpiod_request_cd_irq(). Update those drivers to explicitly call
mmc_gpiod_request_cd_irq() themselves. Ideally, these drivers should be
modified to move their call to mmc_gpio_request_cd() before their call
to mmc_add_host(). However that's too large a change for stable.
This solves the problem (eliminates the kernel error message above),
since it guarantees that the IRQ can't trigger before mmc_start_host()
is called.
The critical point here is that once sdhci_add_host() calls
mmc_add_host() -> mmc_start_host(), sdhci_add_host() is coded not to
fail. In other words, if there's a chance that mmc_start_host() may have
been called, and CD IRQs triggered, and the delayed_work scheduled,
sdhci_add_host() won't fail, and so cleanup is no longer via
sdhci_pltfm_free() (which doesn't free the IRQ or cancel the work queue)
but instead must be via sdhci_remove_host(), which calls mmc_remove_host()
-> mmc_stop_host(), which does free the IRQ and cancel the work queue.
CC: Russell King <linux@arm.linux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6f67cc6fd1 upstream.
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
Fixes: c7f6558d84 ("mmc: Add realtek USB sdmmc host driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit b315376573 upstream.
.set_uhs_signaling field is currently initialised twice once to the
arch specific callback pxav3_set_uhs_signaling, and also to the generic
sdhci_set_uhs_signaling callback.
This means that uhs is currently broken for this platform currently, as pxav3
has some special constriants which means it can't use the generic callback.
This happened in
commit 96d7b78cfc ("mmc: sdhci: convert sdhci_set_uhs_signaling() into a library function")
commit a702c8abb2 ("mmc: host: split up sdhci-pxa, create sdhci-pxav3.c")'
Fix this and hopefully prevent it happening in the future by ensuring named
initialisers always follow the declaration order in the structure definition.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit dea67c4ec8 upstream.
781e989cf5 ("mmc: sdhci: convert to new SDIO IRQ handling") and
bf3b5ec66b ("mmc: sdio_irq: rework sdio irq handling") disabled
the use of our own custom threaded IRQ handler, but left in an
unconditional wake_up_process() on that handler at resume-time.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80151
In addition, the check for MMC_CAP_SDIO_IRQ capability is added
before enable sdio IRQ.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 31d9f8faf9 upstream.
Current caching implementation during regcache_sync() call bypasses
all register writes of values that are already known as default
(regmap reg_defaults). Same time in TLV320AIC3x codecs register 5
(AIC3X_PLL_PROGC_REG) write should be immediately followed by register
6 write (AIC3X_PLL_PROGD_REG) even if it was not changed. Otherwise
both registers will not be written.
This brings to issue that appears particulary in case of 44.1kHz
playback with 19.2MHz master clock. In this case AIC3X_PLL_PROGC_REG
is 0x6e while AIC3X_PLL_PROGD_REG is 0x0 (same as register
default). Thus AIC3X_PLL_PROGC_REG also remains not written and we get
wrong playback speed.
In this patch snd_soc_read() is used to get cached pll values and
snd_soc_write() (unlike regcache_sync() this function doesn't bypasses
hardware default values) to write them to registers.
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e5092c96c9 upstream.
Coverity spotted the following possible use-after-free condition in
dapm_create_or_share_mixmux_kcontrol():
If kcontrol is NULL, and (wname_in_long_name && kcname_in_long_name)
validates to true, 'name' will be set to an allocated string, and be
freed a few lines later via the 'long_name' alias. 'name', however,
is used by dev_err() in case snd_ctl_add() fails.
Fix this by adding a jump label that frees 'long_name' at the end of
the function.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 37017ac684 upstream.
The Broadcom OSB4 IDE Controller (vendor and device IDs: 1166:0211)
does not support 64-KB DMA transfers.
Whenever a 64-KB DMA transfer is attempted,
the transfer fails and messages similar to the following
are written to the console log:
[ 2431.851125] sr 0:0:0:0: [sr0] Unhandled sense code
[ 2431.851139] sr 0:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 2431.851152] sr 0:0:0:0: [sr0] Sense Key : Hardware Error [current]
[ 2431.851166] sr 0:0:0:0: [sr0] Add. Sense: Logical unit communication time-out
[ 2431.851182] sr 0:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 76 f4 00 00 40 00
[ 2431.851210] end_request: I/O error, dev sr0, sector 121808
When the libata and pata_serverworks modules
are recompiled with ATA_DEBUG and ATA_VERBOSE_DEBUG defined in libata.h,
the 64-KB transfer size in the scatter-gather list can be seen
in the console log:
[ 2664.897267] sr 9:0:0:0: [sr0] Send:
[ 2664.897274] 0xf63d85e0
[ 2664.897283] sr 9:0:0:0: [sr0] CDB:
[ 2664.897288] Read(10): 28 00 00 00 7f b4 00 00 40 00
[ 2664.897319] buffer = 0xf6d6fbc0, bufflen = 131072, queuecommand 0xf81b7700
[ 2664.897331] ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 7f b4 00 00 40
[ 2664.897338] ata_scsi_translate: ENTER
[ 2664.897345] ata_sg_setup: ENTER, ata1
[ 2664.897356] ata_sg_setup: 3 sg elements mapped
[ 2664.897364] ata_bmdma_fill_sg: PRD[0] = (0x66FD2000, 0xE000)
[ 2664.897371] ata_bmdma_fill_sg: PRD[1] = (0x65000000, 0x10000)
------------------------------------------------------> =======
[ 2664.897378] ata_bmdma_fill_sg: PRD[2] = (0x66A10000, 0x2000)
[ 2664.897386] ata1: ata_dev_select: ENTER, device 0, wait 1
[ 2664.897422] ata_sff_tf_load: feat 0x1 nsect 0x0 lba 0x0 0x0 0xFC
[ 2664.897428] ata_sff_tf_load: device 0xA0
[ 2664.897448] ata_sff_exec_command: ata1: cmd 0xA0
[ 2664.897457] ata_scsi_translate: EXIT
[ 2664.897462] leaving scsi_dispatch_cmnd()
[ 2664.897497] Doing sr request, dev = sr0, block = 0
[ 2664.897507] sr0 : reading 64/256 512 byte blocks.
[ 2664.897553] ata_sff_hsm_move: ata1: protocol 7 task_state 1 (dev_stat 0x58)
[ 2664.897560] atapi_send_cdb: send cdb
[ 2666.910058] ata_bmdma_port_intr: ata1: host_stat 0x64
[ 2666.910079] __ata_sff_port_intr: ata1: protocol 7 task_state 3
[ 2666.910093] ata_sff_hsm_move: ata1: protocol 7 task_state 3 (dev_stat 0x51)
[ 2666.910101] ata_sff_hsm_move: ata1: protocol 7 task_state 4 (dev_stat 0x51)
[ 2666.910129] sr 9:0:0:0: [sr0] Done:
[ 2666.910136] 0xf63d85e0 TIMEOUT
lspci shows that the driver used for the Broadcom OSB4 IDE Controller is
pata_serverworks:
00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8e [Master SecP SecO PriP])
Flags: bus master, medium devsel, latency 64
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=4]
I/O ports at 1440 [size=16]
Kernel driver in use: pata_serverworks
The pata_serverworks driver supports five distinct device IDs,
one being the OSB4 and the other four belonging to the CSB series.
The CSB series appears to support 64-KB DMA transfers,
as tests on a machine with an SAI2 motherboard
containing a Broadcom CSB5 IDE Controller (vendor and device IDs: 1166:0212)
showed no problems with 64-KB DMA transfers.
This problem was first discovered when attempting to install openSUSE
from a DVD on a machine with an STL2 motherboard.
Using the pata_serverworks module,
older releases of openSUSE will not install at all due to the timeouts.
Releases of openSUSE prior to 11.3 can be installed by disabling
the pata_serverworks module using the brokenmodules boot parameter,
which causes the serverworks module to be used instead.
Recent releases of openSUSE (12.2 and later) include better error recovery and
will install, though very slowly.
On all openSUSE releases, the problem can be recreated
on a machine containing a Broadcom OSB4 IDE Controller
by mounting an install DVD and running a command similar to the following:
find /mnt -type f -print | xargs cat > /dev/null
The patch below corrects the problem.
Similar to the other ATA drivers that do not support 64-KB DMA transfers,
the patch changes the ata_port_operations qc_prep vector to point to a routine
that breaks any 64-KB segment into two 32-KB segments and
changes the scsi_host_template sg_tablesize element to reduce by half
the number of scatter/gather elements allowed.
These two changes affect only the OSB4.
Signed-off-by: Scott Carter <ccscott@funsoft.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
