This bus has three USB-related devices attached to it:
0x25: Maxim 77759 Type-C port controller
0x35: Maxim 20339EWB Surge protection IC
0x36: Maxim 77759 Fuel gauge
0x57: NXP PCA9468 Battery charger
0x66: Maxim 77759 PMIC
0x69: Maxim 77759 Charger
where the Maxim 77759 has multiple i2c slave addresses.
These don't have (upstream) Linux drivers yet, but nevertheless we can
enable the bus so as to allow working on them (and to make i2cdetect /
i2cdump / etc. work).
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240201161258.1013664-8-andre.draszik@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
On the gs101-oriole board, i2c bus 12 has various USB-related
controllers attached to it.
Note the selection of the USI protocol is intentionally left for the
board dts file.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240201161258.1013664-7-andre.draszik@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
submit_flushes
atomic_set(&mddev->flush_pending, 1);
rdev_for_each_rcu(rdev, mddev)
atomic_inc(&mddev->flush_pending);
bi->bi_end_io = md_end_flush
submit_bio(bi);
/* flush io is done first */
md_end_flush
if (atomic_dec_and_test(&mddev->flush_pending))
percpu_ref_put(&mddev->active_io)
-> active_io is not released
if (atomic_dec_and_test(&mddev->flush_pending))
-> missing release of active_io
For consequence, mddev_suspend() will wait for 'active_io' to be zero
forever.
Fix this problem by releasing 'active_io' in submit_flushes() if
'flush_pending' is decreased to zero.
Fixes: fa2bbff7b0 ("md: synchronize flush io with array reconfiguration")
Cc: stable@vger.kernel.org # v6.1+
Reported-by: Blazej Kucman <blazej.kucman@linux.intel.com>
Closes: https://lore.kernel.org/lkml/20240130172524.0000417b@linux.intel.com/
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240201092559.910982-7-yukuai1@huaweicloud.com
Enable the cmu-peric1 clock controller. It feeds additional USI, I3C
and PWM interfaces / busses.
Note that &sysreg_peric1 needs a clock to be able to access its
registers and now that Linux knows about this clock, we need to add it
in this commit as well so as to keep &sysreg_peric1 working, so that
the clock can be enabled as and when needed.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240201161258.1013664-6-andre.draszik@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The Devicetree binding headers for Samsung Exynos and Google GS101 clock
controllers, used by the Samsung clock controller drivers.
-----BEGIN PGP SIGNATURE-----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=TjPm
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-bindings-clk-6.9-3' into next/dt64
dt-bindings for Google GS101 clock controllers for v6.9
The Devicetree binding headers for Samsung Exynos and Google GS101 clock
controllers, used by the Samsung clock controller drivers.
older NULL-pointer dereference in ccp.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEn51F/lCuNhUwmDeSxycdCkmxi6cFAmW8v0cACgkQxycdCkmx
i6ctnRAAht0xsrwQo7pbfQJLdNJb8GgA+E4ym+xbvP/+/Sn+CKWi0wYPIyygYlne
XM1/FMsSxitQvULwJTMsXiEbXRPw+HsDd0SGseUpM+WP491WnzKi6qjjr1z8Hceh
7mpW2wIXV0drAmCS3SCFuPPS7SMgUwD/R4jMm6mf8tYNYc6qU6HF3EV5MKgmJwmq
jbzvWVJ2Wxl7zLx7wAjltM2xAsOPy6PjB2RnEfO0U7i8MFj7scSiRkje1wT2oiJb
wbibaNsbJetNq8e3XmRMHxhzIeZTQWIZxBJU0t2o9NEwCTEbXF1vjU/5kPjIAGCh
8iKhMlWoJ2h8oROFnCI7iO8t3FDZtexfKp/6HAd24jaL+4fsMrL7FRIDZX+O08A1
Kg8vvKjHrm/FF0aOmwWq1Fe/+5TOfHKbYa2/7A2HGWYdtN7Es/9gHidyLoQuBoqc
ZrDlzVIQSm5V4UgIPG/oOY3tVz+uW98QFDXhBHONar0nkZgaVJAuQ1wKFEQzZDch
bvweOsNMYBljD5YvODTCMANxY+xidsr5KkDIe210VvmsnxSe0sTvU0eSM4W07ZFX
ZbjjvOAazMxNB+aFn+aJvyHW96al38L/FrGRVgy9FsESNNt2YahHarW/9Dy0Rgyv
imU+qY83ORSJeVGhwByduen13WquOsdlSATFzDzav6DScOBEbuM=
=sqpx
-----END PGP SIGNATURE-----
Merge tag 'v6.8-p3' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"Fix regressions in cbc and algif_hash, as well as an older
NULL-pointer dereference in ccp"
* tag 'v6.8-p3' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algif_hash - Remove bogus SGL free on zero-length error path
crypto: cbc - Ensure statesize is zero
crypto: ccp - Fix null pointer dereference in __sev_platform_shutdown_locked
According to a syzbot report, end_buffer_async_write(), which handles the
completion of block device writes, may detect abnormal condition of the
buffer async_write flag and cause a BUG_ON failure when using nilfs2.
Nilfs2 itself does not use end_buffer_async_write(). But, the async_write
flag is now used as a marker by commit 7f42ec3941 ("nilfs2: fix issue
with race condition of competition between segments for dirty blocks") as
a means of resolving double list insertion of dirty blocks in
nilfs_lookup_dirty_data_buffers() and nilfs_lookup_node_buffers() and the
resulting crash.
This modification is safe as long as it is used for file data and b-tree
node blocks where the page caches are independent. However, it was
irrelevant and redundant to also introduce async_write for segment summary
and super root blocks that share buffers with the backing device. This
led to the possibility that the BUG_ON check in end_buffer_async_write
would fail as described above, if independent writebacks of the backing
device occurred in parallel.
The use of async_write for segment summary buffers has already been
removed in a previous change.
Fix this issue by removing the manipulation of the async_write flag for
the remaining super root block buffer.
Link: https://lkml.kernel.org/r/20240203161645.4992-1-konishi.ryusuke@gmail.com
Fixes: 7f42ec3941 ("nilfs2: fix issue with race condition of competition between segments for dirty blocks")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+5c04210f7c7f897c1e7f@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/00000000000019a97c05fd42f8c8@google.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
DAMON sysfs interface's update_schemes_tried_regions command has a timeout
of two apply intervals of the DAMOS scheme. Having zero value DAMOS
scheme apply interval means it will use the aggregation interval as the
value. However, the timeout setup logic is mistakenly using the sampling
interval insted of the aggregartion interval for the case. This could
cause earlier-than-expected timeout of the command. Fix it.
Link: https://lkml.kernel.org/r/20240202191956.88791-1-sj@kernel.org
Fixes: 7d6fa31a2f ("mm/damon/sysfs-schemes: add timeout for update_schemes_tried_regions")
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org> # 6.7.x
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Syzbot reported a hang issue in migrate_pages_batch() called by mbind()
and nilfs_lookup_dirty_data_buffers() called in the log writer of nilfs2.
While migrate_pages_batch() locks a folio and waits for the writeback to
complete, the log writer thread that should bring the writeback to
completion picks up the folio being written back in
nilfs_lookup_dirty_data_buffers() that it calls for subsequent log
creation and was trying to lock the folio. Thus causing a deadlock.
In the first place, it is unexpected that folios/pages in the middle of
writeback will be updated and become dirty. Nilfs2 adds a checksum to
verify the validity of the log being written and uses it for recovery at
mount, so data changes during writeback are suppressed. Since this is
broken, an unclean shutdown could potentially cause recovery to fail.
Investigation revealed that the root cause is that the wait for writeback
completion in nilfs_page_mkwrite() is conditional, and if the backing
device does not require stable writes, data may be modified without
waiting.
Fix these issues by making nilfs_page_mkwrite() wait for writeback to
finish regardless of the stable write requirement of the backing device.
Link: https://lkml.kernel.org/r/20240131145657.4209-1-konishi.ryusuke@gmail.com
Fixes: 1d1d1a7672 ("mm: only enforce stable page writes if the backing device requires it")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+ee2ae68da3b22d04cd8d@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/00000000000047d819061004ad6c@google.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
I will lose access to my @linaro.org email address next week, update the
MAINTAINERS file and map it in .mailmap with the new email address.
Link: https://lkml.kernel.org/r/20240201021022.886-1-leo.yan@linux.dev
Signed-off-by: Leo Yan <leo.yan@linux.dev>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Ian Rogers <irogers@google.com>
Cc: James Clark <james.clark@arm.com>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
LRU_SKIP can only be returned if we don't ever dropped lru lock, or we
need to return LRU_RETRY to restart from the head of lru list.
Otherwise, the iteration might continue from a cursor position that was
freed while the locks were dropped.
Actually we may need to introduce another LRU_STOP to really terminate the
ongoing shrinking scan process, when we encounter a warm page already in
the swap cache. The current list_lru implementation doesn't have this
function to early break from __list_lru_walk_one.
Link: https://lkml.kernel.org/r/20240126-zswap-writeback-race-v2-1-b10479847099@bytedance.com
Fixes: b5ba474f3f ("zswap: shrink zswap pool based on memory pressure")
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Nhat Pham <nphamcs@gmail.com>
Cc: Chris Li <chriscli@google.com>
Cc: Yosry Ahmed <yosryahmed@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Add current email address as QUIC email is no longer active.
Link: https://lkml.kernel.org/r/20240131034311.46706-1-john@jmoon.dev
Signed-off-by: John Moon <john@jmoon.dev>
Acked-by: Trilok Soni <quic_tsoni@quicinc.com>
Cc: Elliot Berman <quic_eberman@quicinc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In the per-memcg LRU universe, LRU removal uses entry->objcg to determine
which list count needs to be decreased. Drop the objcg reference after
updating the LRU, to fix a possible use-after-free.
Link: https://lkml.kernel.org/r/20240130013438.565167-1-hannes@cmpxchg.org
Fixes: a65b0e7607 ("zswap: make shrinking memcg-aware")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Yosry Ahmed <yosryahmed@google.com>
Reviewed-by: Nhat Pham <nphamcs@gmail.com>
Reviewed-by: Chengming Zhou <zhouchengming@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We need to leave lazy MMU mode before unlocking.
Link: https://lkml.kernel.org/r/20240126032608.355899-1-senozhatsky@chromium.org
Fixes: b2f557a21b ("mm/madvise: add cond_resched() in madvise_cold_or_pageout_pte_range()")
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Jiexun Wang <wangjiexun@tinylab.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The change [1] missed ARM architecture when fixing major fault accounting
for page fault retry under per-VMA lock.
The user-visible effects is that it restores correct major fault
accounting that was broken after [2] was merged in 6.7 kernel. The
more detailed description is in [3] and this patch simply adds the
same fix to ARM architecture which I missed in [3].
Add missing code to fix ARM architecture fault accounting.
[1] 46e714c729 ("arch/mm/fault: fix major fault accounting when retrying under per-VMA lock")
[2] https://lore.kernel.org/all/20231006195318.4087158-6-willy@infradead.org/
[3] https://lore.kernel.org/all/20231226214610.109282-1-surenb@google.com/
Link: https://lkml.kernel.org/r/20240123064305.2829244-1-surenb@google.com
Fixes: 12214eba19 ("mm: handle read faults under the VMA lock")
Reported-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In memcg_rstat_updated(), we iterate the memcg being updated and its
parents to update memcg->vmstats_percpu->stats_updates in the fast path
(i.e. no atomic updates). According to my math, this is 3 memory loads
(and potentially 3 cache misses) per memcg:
- Load the address of memcg->vmstats_percpu.
- Load vmstats_percpu->stats_updates (based on some percpu calculation).
- Load the address of the parent memcg.
Avoid most of the cache misses by caching a pointer from each struct
memcg_vmstats_percpu to its parent on the corresponding CPU. In this
case, for the first memcg we have 2 memory loads (same as above):
- Load the address of memcg->vmstats_percpu.
- Load vmstats_percpu->stats_updates (based on some percpu calculation).
Then for each additional memcg, we need a single load to get the
parent's stats_updates directly. This reduces the number of loads from
O(3N) to O(2+N) -- where N is the number of memcgs we need to iterate.
Additionally, stash a pointer to memcg->vmstats in each struct
memcg_vmstats_percpu such that we can access the atomic counter that all
CPUs fold into, memcg->vmstats->stats_updates.
memcg_should_flush_stats() is changed to memcg_vmstats_needs_flush() to
accept a struct memcg_vmstats pointer accordingly.
In struct memcg_vmstats_percpu, make sure both pointers together with
stats_updates live on the same cacheline. Finally, update
mem_cgroup_alloc() to take in a parent pointer and initialize the new
cache pointers on each CPU. The percpu loop in mem_cgroup_alloc() may
look concerning, but there are multiple similar loops in the cgroup
creation path (e.g. cgroup_rstat_init()), most of which are hidden
within alloc_percpu().
According to Oliver's testing [1], this fixes multiple 30-38%
regressions in vm-scalability, will-it-scale-tlb_flush2, and
will-it-scale-fallocate1. This comes at a cost of 2 more pointers per
CPU (<2KB on a machine with 128 CPUs).
[1] https://lore.kernel.org/lkml/ZbDJsfsZt2ITyo61@xsang-OptiPlex-9020/
[yosryahmed@google.com: fix struct memcg_vmstats_percpu size and alignment]
Link: https://lkml.kernel.org/r/20240203044612.1234216-1-yosryahmed@google.com
Link: https://lkml.kernel.org/r/20240124100023.660032-1-yosryahmed@google.com
Signed-off-by: Yosry Ahmed <yosryahmed@google.com>
Fixes: 8d59d2214c ("mm: memcg: make stats flushing threshold per-memcg")
Tested-by: kernel test robot <oliver.sang@intel.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202401221624.cb53a8ca-oliver.sang@intel.com
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Greg Thelen <gthelen@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The helper function nilfs_recovery_copy_block() of
nilfs_recovery_dsync_blocks(), which recovers data from logs created by
data sync writes during a mount after an unclean shutdown, incorrectly
calculates the on-page offset when copying repair data to the file's page
cache. In environments where the block size is smaller than the page
size, this flaw can cause data corruption and leak uninitialized memory
bytes during the recovery process.
Fix these issues by correcting this byte offset calculation on the page.
Link: https://lkml.kernel.org/r/20240124121936.10575-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit c33c794828 ("mm: ptep_get() conversion") converted all (non-arch)
call sites to use ptep_get() instead of doing a direct dereference of the
pte. Full rationale can be found in that commit's log.
Since then, UFFDIO_MOVE has been implemented which does 7 direct pte
dereferences. Let's fix those up to use ptep_get().
I've asserted in the past that there is no reliable automated mechanism to
catch these; I'm relying on a combination of Coccinelle (which throws up a
lot of false positives) and some compiler magic to force a compiler error
on dereference. But given the frequency with which new issues are coming
up, I'll add it to my todo list to try to find an automated solution.
Link: https://lkml.kernel.org/r/20240123141755.3836179-1-ryan.roberts@arm.com
Fixes: adef440691 ("userfaultfd: UFFDIO_MOVE uABI")
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Suren Baghdasaryan <surenb@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
After the recent changes nobody use siglock to read the values protected
by stats_lock, we can kill spin_lock_irq(¤t->sighand->siglock) and
update the comment.
With this patch only __exit_signal() and thread_group_start_cputime() take
stats_lock under siglock.
Link: https://lkml.kernel.org/r/20240123153359.GA21866@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Dylan Hatch <dylanbhatch@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
lock_task_sighand() can trigger a hard lockup. If NR_CPUS threads call
do_task_stat() at the same time and the process has NR_THREADS, it will
spin with irqs disabled O(NR_CPUS * NR_THREADS) time.
Change do_task_stat() to use sig->stats_lock to gather the statistics
outside of ->siglock protected section, in the likely case this code will
run lockless.
Link: https://lkml.kernel.org/r/20240123153357.GA21857@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Dylan Hatch <dylanbhatch@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "fs/proc: do_task_stat: use sig->stats_".
do_task_stat() has the same problem as getrusage() had before "getrusage:
use sig->stats_lock rather than lock_task_sighand()": a hard lockup. If
NR_CPUS threads call lock_task_sighand() at the same time and the process
has NR_THREADS, spin_lock_irq will spin with irqs disabled O(NR_CPUS *
NR_THREADS) time.
This patch (of 3):
thread_group_cputime() does its own locking, we can safely shift
thread_group_cputime_adjusted() which does another for_each_thread loop
outside of ->siglock protected section.
Not only this removes for_each_thread() from the critical section with
irqs disabled, this removes another case when stats_lock is taken with
siglock held. We want to remove this dependency, then we can change the
users of stats_lock to not disable irqs.
Link: https://lkml.kernel.org/r/20240123153313.GA21832@redhat.com
Link: https://lkml.kernel.org/r/20240123153355.GA21854@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Dylan Hatch <dylanbhatch@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
lock_task_sighand() can trigger a hard lockup. If NR_CPUS threads call
getrusage() at the same time and the process has NR_THREADS, spin_lock_irq
will spin with irqs disabled O(NR_CPUS * NR_THREADS) time.
Change getrusage() to use sig->stats_lock, it was specifically designed
for this type of use. This way it runs lockless in the likely case.
TODO:
- Change do_task_stat() to use sig->stats_lock too, then we can
remove spin_lock_irq(siglock) in wait_task_zombie().
- Turn sig->stats_lock into seqcount_rwlock_t, this way the
readers in the slow mode won't exclude each other. See
https://lore.kernel.org/all/20230913154907.GA26210@redhat.com/
- stats_lock has to disable irqs because ->siglock can be taken
in irq context, it would be very nice to change __exit_signal()
to avoid the siglock->stats_lock dependency.
Link: https://lkml.kernel.org/r/20240122155053.GA26214@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Dylan Hatch <dylanbhatch@google.com>
Tested-by: Dylan Hatch <dylanbhatch@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "getrusage: use sig->stats_lock", v2.
This patch (of 2):
thread_group_cputime() does its own locking, we can safely shift
thread_group_cputime_adjusted() which does another for_each_thread loop
outside of ->siglock protected section.
This is also preparation for the next patch which changes getrusage() to
use stats_lock instead of siglock, thread_group_cputime() takes the same
lock. With the current implementation recursive read_seqbegin_or_lock()
is fine, thread_group_cputime() can't enter the slow mode if the caller
holds stats_lock, yet this looks more safe and better performance-wise.
Link: https://lkml.kernel.org/r/20240122155023.GA26169@redhat.com
Link: https://lkml.kernel.org/r/20240122155050.GA26205@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Dylan Hatch <dylanbhatch@google.com>
Tested-by: Dylan Hatch <dylanbhatch@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
For shared memory of type SHM_HUGETLB, hugetlb pages are reserved in
shmget() call. If SHM_NORESERVE flags is specified then the hugetlb pages
are not reserved. However when the shared memory is attached with the
shmat() call the hugetlb pages are getting reserved incorrectly for
SHM_HUGETLB shared memory created with SHM_NORESERVE which is a bug.
-------------------------------
Following test shows the issue.
$cat shmhtb.c
int main()
{
int shmflags = 0660 | IPC_CREAT | SHM_HUGETLB | SHM_NORESERVE;
int shmid;
shmid = shmget(SKEY, SHMSZ, shmflags);
if (shmid < 0)
{
printf("shmat: shmget() failed, %d\n", errno);
return 1;
}
printf("After shmget()\n");
system("cat /proc/meminfo | grep -i hugepages_");
shmat(shmid, NULL, 0);
printf("\nAfter shmat()\n");
system("cat /proc/meminfo | grep -i hugepages_");
shmctl(shmid, IPC_RMID, NULL);
return 0;
}
#sysctl -w vm.nr_hugepages=20
#./shmhtb
After shmget()
HugePages_Total: 20
HugePages_Free: 20
HugePages_Rsvd: 0
HugePages_Surp: 0
After shmat()
HugePages_Total: 20
HugePages_Free: 20
HugePages_Rsvd: 5 <--
HugePages_Surp: 0
--------------------------------
Fix is to ensure that hugetlb pages are not reserved for SHM_HUGETLB shared
memory in the shmat() call.
Link: https://lkml.kernel.org/r/1706040282-12388-1-git-send-email-prakash.sangappa@oracle.com
Signed-off-by: Prakash Sangappa <prakash.sangappa@oracle.com>
Acked-by: Muchun Song <muchun.song@linux.dev>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Now that the driver core can properly handle constant struct bus_type,
move the pci_epf_bus_type variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240204-bus_cleanup-pci-v1-1-300267a1e99e@marliere.net
[mani: modified subject to reflect subsys prefix]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair per netns
and one unregister_netdevice_many() call.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-17-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair per netns
and one unregister_netdevice_many() call.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-16-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair
and one unregister_netdevice_many() call.
This patch takes care of ipip, ip_vti, and ip_gre tunnels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-15-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair
and one unregister_netdevice_many() call.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-14-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair
and one unregister_netdevice_many() call.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-13-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair
and one unregister_netdevice_many() call.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-12-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair
and one unregister_netdevice_many() call.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-11-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair per netns
and one unregister_netdevice_many() call.
v4: (Paolo feedback : https://netdev-3.bots.linux.dev/vmksft-net/results/453141/17-udpgro-fwd-sh/stdout )
- Changed vxlan_destroy_tunnels() to use vxlan_dellink()
instead of unregister_netdevice_queue to propely remove
devices from vn->vxlan_list.
- vxlan_destroy_tunnels() can simply iterate one list (vn->vxlan_list)
to find all devices in the most efficient way.
- Moved sanity checks in a separate vxlan_exit_net() method.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-10-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
unregister_nexthop_notifier() assumes the caller does not hold rtnl.
We need in the following patch to use it from a context
already holding rtnl.
Add __unregister_nexthop_notifier().
unregister_nexthop_notifier() becomes a wrapper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-9-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair per netns
and one unregister_netdevice_many() call per netns.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-8-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair,
and one unregister_netdevice_many() call.
Note: it should be possible to remove the synchronize_net()
call from geneve_sock_release() in a future patch.
v4: move WARN_ON_ONCE(!list_empty(&gn->sock_list))
into geneve_exit_net(), after devices have been unregistered.
(Antoine Tenart feedback)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-7-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair,
and one unregister_netdevice_many() call.
v2: Added bond_net_pre_exit() method to make sure bond_destroy_sysfs()
is called before we unregister the devices in bond_net_exit_batch_rtnl
(Antoine Tenart : https://lore.kernel.org/netdev/170688415193.5216.10499830272732622816@kwain/)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-6-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair,
and one unregister_netdevice_many() call.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
exit_batch_rtnl() is called while RTNL is held.
This saves one rtnl_lock()/rtnl_unlock() pair.
We also need to create nexthop_net_exit()
to make sure net->nexthop.devhash is not freed too soon,
otherwise we will not be able to unregister netdev
from exit_batch_rtnl() methods.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Many (struct pernet_operations)->exit_batch() methods have
to acquire rtnl.
In presence of rtnl mutex pressure, this makes cleanup_net()
very slow.
This patch adds a new exit_batch_rtnl() method to reduce
number of rtnl acquisitions from cleanup_net().
exit_batch_rtnl() handlers are called while rtnl is locked,
and devices to be killed can be queued in a list provided
as their second argument.
A single unregister_netdevice_many() is called right
before rtnl is released.
exit_batch_rtnl() handlers are called before ->exit() and
->exit_batch() handlers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arınç ÜNAL says:
====================
MT7530 DSA Subdriver Improvements Act II
This is the second patch series with the goal of simplifying the MT7530 DSA
subdriver and improving support for MT7530, MT7531, and the switch on the
MT7988 SoC.
I have done a simple ping test to confirm basic communication on all switch
ports on MCM and standalone MT7530, and MT7531 switch with this patch
series applied.
MT7621 Unielec, MCM MT7530:
rgmii-only-gmac0-mt7621-unielec-u7621-06-16m.dtb
gmac0-and-gmac1-mt7621-unielec-u7621-06-16m.dtb
tftpboot 0x80008000 mips-uzImage.bin; tftpboot 0x83000000 mips-rootfs.cpio.uboot; tftpboot 0x83f00000 $dtb; bootm 0x80008000 0x83000000 0x83f00000
MT7622 Bananapi, MT7531:
gmac0-and-gmac1-mt7622-bananapi-bpi-r64.dtb
tftpboot 0x40000000 arm64-Image; tftpboot 0x45000000 arm64-rootfs.cpio.uboot; tftpboot 0x4a000000 $dtb; booti 0x40000000 0x45000000 0x4a000000
MT7623 Bananapi, standalone MT7530:
rgmii-only-gmac0-mt7623n-bananapi-bpi-r2.dtb
gmac0-and-gmac1-mt7623n-bananapi-bpi-r2.dtb
tftpboot 0x80008000 arm-zImage; tftpboot 0x83000000 arm-rootfs.cpio.uboot; tftpboot 0x83f00000 $dtb; bootz 0x80008000 0x83000000 0x83f00000
This patch series is the continuation of the patch series linked below.
https://lore.kernel.org/r/20230522121532.86610-1-arinc.unal@arinc9.com
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
====================
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-0-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's no need to clear the config->supported_interfaces bitmap before
reporting the supported interfaces as all bits in the bitmap will already
be initialized to zero when the phylink_config structure is allocated. The
"config" pointer points to &dp->phylink_config, and "dp" is allocated by
dsa_port_touch() with kzalloc(), so all its fields are filled with zeroes.
There's no code that would change the bitmap beforehand. Remove it.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-7-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the switch on the MT7988 SoC, as shown in Block Diagram 8.1.1.3 on page
125 of "MT7988A Wi-Fi 7 Generation Router Platform: Datasheet (Open
Version) v0.1", there are only 4 PHYs. That's port 0 to 3. Set the case for
ports which connect to switch PHYs to '0 ... 3'.
Port 4 and 5 are not used at all in this design.
Link: https://wiki.banana-pi.org/Banana_Pi_BPI-R4#Documents [1]
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-6-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The pad_setup function pointer was introduced with 88bdef8be9 ("net: dsa:
mt7530: Extend device data ready for adding a new hardware"). It was being
used to set up the core clock and port 6 of the MT7530 switch, and pll of
the MT7531 switch.
All of these were moved to more appropriate locations, and it was never
used for the switch on the MT7988 SoC. Therefore, this function pointer
hasn't got a use anymore. Remove it.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-5-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mt7530_pad_clk_setup() is called if port 6 is enabled. It used to do more
things than setting up port 6. That part was moved to more appropriate
locations, mt7530_setup() and mt7530_pll_setup().
Now that all it does is set up port 6, rename it to mt7530_setup_port6(),
and move it to a more appropriate location, under mt7530_mac_config().
Change mt7530_setup_port6() to void as there're no error cases.
Leave an empty mt7530_pad_clk_setup() to satisfy the pad_setup function
pointer.
This is the code path for setting up the ports before:
dsa_switch_ops :: phylink_mac_config() -> mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt753x_info :: mac_port_config() -> mt7530_mac_config()
-> mt7530_setup_port5()
-> mt753x_pad_setup()
-> mt753x_info :: pad_setup() -> mt7530_pad_clk_setup()
This is after:
dsa_switch_ops :: phylink_mac_config() -> mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt753x_info :: mac_port_config() -> mt7530_mac_config()
-> mt7530_setup_port5()
-> mt7530_setup_port6()
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-4-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>