Commit graph

153,333 commits

Author SHA1 Message Date
Huang, Xiong
5e5c0964d9 atl1c: do MAC-reset when PHY link down
There may be tx-skbs still pending in HW when PHY link down.
Reset MAC will make the DMA engine go to the start point.
and release all pending skbs.
Note: Reset MAC will clear any interrupt status and mask.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:44:15 -04:00
Huang, Xiong
0aa76ce332 atl1c: cancel task when interface closed
common_task might be running while close routine is called,
wait/cancel it.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:44:15 -04:00
Huang, Xiong
f56fa56737 atl1c: enlarge L1 response waiting timer
The hardware incorrectly process L0S/L1 entrance if the chipset/root
response after specific/shorter timer and cause system hang.
Enlarge the timeout value to avoid this issue.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:44:14 -04:00
Huang, Xiong
229e6b6e9c atl1c: refine mac address related code
On some platform with EEPROM/OTP existing, the BIOS could overwrite
a new MAC address for the NIC. so, the permanent mac address should
be from BIOS. the address is restored when driver removing.
Voltage raising isn't applicable for l1d.
Replace swab32 with htonl for big/little endian platform.
related Registers are refined as well.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:44:14 -04:00
Huang, Xiong
e119258009 atl1c: remove code of closing register writable attribution
The Close-action is done by atl1c_reset_pcie, remove it from
atl1c_get_permanent_address.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:44:14 -04:00
Huang, Xiong
87eabe6bf0 atl1c: clear WoL status when reset pcie
WoL status is read-clear and should be cleared when in S0
status.
putting it in atl1c_reset_pcie is more suitable than
in atl1c_get_permanent_address.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:44:13 -04:00
Huang, Xiong
903d7ce0cc atl1c: add PHY link event(up/down) patch
On some platforms the PHY settings need to change depending on the
cable link status to get better stability.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:44:13 -04:00
Huang, Xiong
7cb6a291ef atl1c: add workaround for issue of bit INTX-disable for MSI interrupt
All supported devices have one issue that msi interrupt doesn't assert
if pci command register bit (PCI_COMMAND_INTX_DISABLE) is set.
Add workaround in drivers/pci/quirks.c

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:44:12 -04:00
Eric Dumazet
1191cb8348 bnx2x: remove some bloat
Before doing skb->head_frag work on bnx2x driver, I found too much stuff
was inlined in bnx2x/bnx2x_cmn.h for no good reason and made my work not
very easy.

Move some big functions out of this include file to the respective .c
file.

A lot of inline keywords are not needed at all in this huge driver.

   text	   data	    bss	    dec	    hex	filename
 490083	   1270	     56	 491409	  77f91	bnx2x/bnx2x.ko.before
 484206	   1270	     56	 485532	  7689c	bnx2x/bnx2x.ko

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:38:17 -04:00
RongQing.Li
d344c4f310 pch_gbe: reprogram multicast address register on reset
The reset logic after a Rx FIFO overrun will clear the programmed
multicast addresses. This patch fixes the issue by reprogramming the
registers after the reset.

The commit eefc48b ("pch_gbe: reprogram multicast address register on
reset") tried to fix this problem, but it introduces unnecessary
codes. In fact, all multicast addresses have been saved in netdev->mc,
So we can call pch_gbe_set_multi() directly after reset_hw and
reset_rx.

This commit kills 50+ line codes

Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:37:27 -04:00
Eric Dumazet
8d4057a938 tg3: provide frags as skb head
This patch converts tg3 driver, one of our reference drivers, to use new
build_skb() api in frag mode.

Instead of using kmalloc() to allocate the memory block that will be
used by build_skb() as skb->head, we use a page fragment.

This is a followup of patch "net: allow skb->head to be a page fragment"

This allows GRO, TCP coalescing, and splice() to be more efficient.

Incidentally, this also removes SLUB slow path contention in kfree()

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:35:42 -04:00
Eric Dumazet
d3836f21b0 net: allow skb->head to be a page fragment
skb->head is currently allocated from kmalloc(). This is convenient but
has the drawback the data cannot be converted to a page fragment if
needed.

We have three spots were it hurts :

1) GRO aggregation

 When a linear skb must be appended to another skb, GRO uses the
frag_list fallback, very inefficient since we keep all struct sk_buff
around. So drivers enabling GRO but delivering linear skbs to network
stack aren't enabling full GRO power.

2) splice(socket -> pipe).

 We must copy the linear part to a page fragment.
 This kind of defeats splice() purpose (zero copy claim)

3) TCP coalescing.

 Recently introduced, this permits to group several contiguous segments
into a single skb. This shortens queue lengths and save kernel memory,
and greatly reduce probabilities of TCP collapses. This coalescing
doesnt work on linear skbs (or we would need to copy data, this would be
too slow)

Given all these issues, the following patch introduces the possibility
of having skb->head be a fragment in itself. We use a new skb flag,
skb->head_frag to carry this information.

build_skb() is changed to accept a frag_size argument. Drivers willing
to provide a page fragment instead of kmalloc() data will set a non zero
value, set to the fragment size.

Then, on situations we need to convert the skb head to a frag in itself,
we can check if skb->head_frag is set and avoid the copies or various
fallbacks we have.

This means drivers currently using frags could be updated to avoid the
current skb->head allocation and reduce their memory footprint (aka skb
truesize). (thats 512 or 1024 bytes saved per skb). This also makes
bpf/netfilter faster since the 'first frag' will be part of skb linear
part, no need to copy data.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:35:11 -04:00
Willem de Bruijn
49cbb1c1e6 forcedeth: add transmit timestamping support
Insert an skb_tx_timestamp call in both ndo_start_xmit routines
Tested to work for the nv_start_xmit_optimized case

Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:33:27 -04:00
Willem de Bruijn
8373c57d6f bnx2x: add transmit timestamping support
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:33:27 -04:00
Willem de Bruijn
80be3129d7 e1000e: add transmit timestamping support
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:33:26 -04:00
Willem de Bruijn
eab467f563 e1000: add transmit timestamping support
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-30 21:33:25 -04:00
Bjorn Helgaas
29473ec23a Merge branch 'topic/yinghai-hostbridge-cleanup' into next 2012-04-30 16:55:58 -06:00
Konrad Rzeszutek Wilk
977f857ca5 PCI: move mutex locking out of pci_dev_reset function
The intent of git commit 6fbf9e7a90
"PCI: Introduce __pci_reset_function_locked to be used when holding
device_lock." was to have a non-locking function that would call
pci_dev_reset function.

But it fell short of that by just probing and not actually reseting
the device. To make that work we need a way to move the lock
around device_lock to not be in pci_dev_reset (as the caller of
__pci_reset_function_locked already holds said lock). We do this by
renaming pci_dev_reset to __pci_dev_reset and bubbling said mutex out
of __pci_dev_reset to pci_dev_reset (a wrapper around __pci_dev_reset).
The __pci_reset_function_locked  can now call __pci_dev_reset without
having to worry about the dead-lock.

Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-04-30 16:47:26 -06:00
Linus Torvalds
e7a7c9ab41 SCSI fixes on 20120430
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJPnjtXAAoJEDeqqVYsXL0MNWkIAMYc5n06Ac/gdLY8xIIYD6GA
 OzLd/NQ2Q4RqZJsX26OueX2ZjMRYDixBAmiw837K9PvrLUHGfMAaninNyzDgVZ3R
 pbIK45OylIQrvMAl/R7ZzqihfxJjg5utqEUt1M2qv/ikkBJ8+zWAJTQKxRYJ1OAW
 9QDhIP986hljNyZfDuqXBvA4XkngYeCO0WLjBOeYCseSzeV8vOLpmsD/ANHDcqA6
 Ct4uM4KJWF4jHz3sN3w5T3morNwvh42onNcy++911HcH5Nc9bkOqBWQAZ5RtINp9
 8rkUz3OtCCQpZz6ffF3ZXJaopuU3ELfP80t03OScr2T75SxLqLf6mFYVAcR7RpQ=
 =nXrE
 -----END PGP SIGNATURE-----

Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
 "This is a set of SAS and SATA fixes; there are one or two longstanding
  bug fixes, but most of this is regression fixes."

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] libfc: update mfs boundry checking
  [SCSI] Revert "[SCSI] libsas: fix sas port naming"
  [SCSI] libsas: fix false positive 'device attached' conditions
  [SCSI] libsas, libata: fix start of life for a sas ata_port
  [SCSI] libsas: fix ata_eh clobbering ex_phys via smp_ata_check_ready
  [SCSI] libsas: unify domain_device sas_rphy lifetimes
  [SCSI] libsas: fix sas_get_port_device regression
  [SCSI] libsas: fix sas_find_bcast_phy() in the presence of 'vacant' phys
  [SCSI] libsas: introduce sas_work to fix sas_drain_work vs sas_queue_work
  [SCSI] libata: Pass correct DMA device to scsi host
  [SCSI] scsi_lib: use correct DMA device in __scsi_alloc_queue
2012-04-30 15:33:50 -07:00
Matthew Garrett
fec6c20b57 efi: Validate UEFI boot variables
A common flaw in UEFI systems is a refusal to POST triggered by a malformed
boot variable. Once in this state, machines may only be restored by
reflashing their firmware with an external hardware device. While this is
obviously a firmware bug, the serious nature of the outcome suggests that
operating systems should filter their variable writes in order to prevent
a malicious user from rendering the machine unusable.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-04-30 15:30:18 -07:00
Mark Brown
7a64761432 regmap: Devices using format_write don't support bulk operations
Set the use_single_rw flag for devices that use format_write() since
format_write() doesn't support any form of block operation.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-30 23:30:15 +01:00
Ashish Jangam
2e33caf16f regmap: Converts group operation into single read write operations
Some devices does not support bulk read and write operations, for them
we have series of single write and read operations.

Signed-off-by: Anthony Olech <Anthony.Olech@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Fixed coding style, don't check use_single_rw before assign --broonie ]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-30 23:29:56 +01:00
Mark Brown
f298536728 regmap: Cache single values read from the chip
If we don't have a cached value for a register and we can cache it then
when we do a read a value we should add it to the cache to save rereading
it later on. Do this for single register reads, for block reads the code
would be a little more complex and this covers most practical usage.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-30 22:57:10 +01:00
Arnd Bergmann
ca731a5da0 Merge branch 'ux500-gpio-pins-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/gpio
Linus Walleij <linus.walleij@linaro.org> writes:

 This is a pull request for the GPIO and pin control stuff
 accumulated in the ST-Ericsson tree. Here we have:

 - Improvements and fixes and a custom pin config API from
   Rabin Vincent

 - Device Tree bindings from Lee Jones

 - Some accumulated patches by yours truly.

 - A MSP platform data init patch from Ola Lilja that is merged
   here due to dependency on pin config work. It is to be
   used with work being worked on in parallel in the ALSA
   SoC subsystem.

 If you wonder about the custom pin config implementation this
 is to be used as a transition base as I am rewriting the
 driver to use pinctrl. Expect a final pull request on top
 of this one that will move the ux500 over to pinctrl.

* 'ux500-gpio-pins-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: ux500: Add support for MSP I2S-devices
  drivers/gpio: gpio-nomadik: Add support for irqdomains
  drivers/gpio: gpio-nomadik: Apply Device Tree bindings
  ARM: ux500: update pin handling
  ARM: ux500: implement pin API
  ARM: ux500: remove a bunch of internal pull-ups
  plat-nomadik: new sleep mode pincfg macros
  gpio/nomadik: use ioremap() instead of static mappings
  gpio/nomadik: support low EMI mode
  gpio/nomadik: fix spurious interrupts with SKE
  gpio/nomadik: cache [rf]w?imsc
  gpio/nomadik: don't set SLPM to 1 for non-wakeup pins

Also includes an update to v3.4-rc4.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-04-30 23:53:58 +02:00
Bjorn Helgaas
284f5f9dba PCI: work around Stratus ftServer broken PCIe hierarchy
A PCIe downstream port is a P2P bridge.  Its secondary interface is
a link that should lead only to device 0 (unless ARI is enabled)[1], so
we don't probe for non-zero device numbers.

Some Stratus ftServer systems have a PCIe downstream port (02:00.0) that
leads to both an upstream port (03:00.0) and a downstream port (03:01.0),
and 03:01.0 has important devices below it:

  [0000:02]-+-00.0-[03-3c]--+-00.0-[04-09]--...
                            \-01.0-[0a-0d]--+-[USB]
                                            +-[NIC]
                                            +-...

Previously, we didn't enumerate device 03:01.0, so USB and the network
didn't work.  This patch adds a DMI quirk to scan all device numbers,
not just 0, below a downstream port.

Based on a patch by Prarit Bhargava.

[1] PCIe spec r3.0, sec 7.3.1

CC: Myron Stowe <mstowe@redhat.com>
CC: Don Dutile <ddutile@redhat.com>
CC: James Paradis <james.paradis@stratus.com>
CC: Matthew Wilcox <matthew.r.wilcox@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-04-30 15:21:02 -06:00
Yinghai Lu
4fa2649a01 PCI: add host bridge release support
We need a hook to release host bridge resources allocated when creating
root bus.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-04-30 14:52:43 -06:00
Yinghai Lu
7b54366358 PCI: add generic device into pci_host_bridge struct
Use that device for pci_root_bus bridge pointer.

Use pci_release_bus_bridge_dev() to release allocated pci_host_bridge in
remove path.

Use root bus bridge pointer to get host bridge pointer instead of searching
host bridge list.  That leaves the host bridge list unused, so remove it.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-04-30 13:53:42 -06:00
Yinghai Lu
459f58ce51 PCI: rename pci_host_bridge() to find_pci_root_bridge()
pci_host_bridge() looks like a C++ constructor.  Also separate
find_pci_root_bus() out.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-04-30 13:53:08 -06:00
Yinghai Lu
610929e119 PCI: move host bridge-related code to host-bridge.c
Move host bridge-related code from probe.c to a new host-bridge.c.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-04-30 13:36:14 -06:00
Linus Torvalds
fbf717629f Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
 "Here are a handful more fixes for powerpc.  The irq stuff are all
  regression fixes, and Gavin's patch is a simple compile fix."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  tty/serial/pmac_zilog: Fix "nobody cared" IRQ message
  powerpc/pseries: Rivet CONFIG_EEH for pSeries platform
  powerpc/irqdomain: Fix broken NR_IRQ references
  powerpc/8xx: Fix NR_IRQ bugs and refactor 8xx interrupt controller
2012-04-30 11:07:53 -07:00
Linus Torvalds
84e92ef4f7 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
 "A simple fix for a recent regression in Synaptics driver"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics - fix regression with "image sensor" trackpads
2012-04-30 10:13:48 -07:00
Justin P. Mattock
589b3d06fd staging: rtl8192u Fix typos.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-30 10:48:48 -04:00
Michael Hennerich
f316983fe0 staging: iio: adc: convert ADI drivers to use kfifo.
sw_ring is depreciated and therefore won't move out of staging.
Prerequisite for lifting affected drivers is to convert them to kfifo.
Update copyright.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-30 10:28:10 -04:00
Steffen Müller
166cb70e97 usb: add USB_QUIRK_RESET_RESUME for M-Audio 88es
Tested-by: Steffen Müller <steffen.mueller@radio-frei.de>
Signed-off-by: Steffen Müller <steffen.mueller@radio-frei.de>
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-30 10:26:42 -04:00
Oliver Neukum
12a98b2bd8 USB: cdc-wdm: cleanup error codes
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

The internal error codes returned in the write() code
path cannot be simply passed on to user space.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-30 09:58:56 -04:00
Bjørn Mork
880bca3a2a USB: cdc-wdm: add debug messages on cleanup
Device state cleanup is done in either wdm_disconnect or
wdm_release depending on the order they are called. Adding
a couple of debug messages to document the program flow.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-30 09:57:27 -04:00
David Mackey
15ed103a98 edac: Fix spelling errors.
Signed-off-by: David Mackey <tdmackey@twitter.com>
Signed-off-by: Vinson Lee <vlee@twitter.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-04-30 13:28:41 +02:00
Jesper Juhl
90449e5dee qla1280: Remove redundant NULL check before release_firmware() call
release_firmware() checks for NULL pointers internally so checking
before calling the function is redundant.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-04-30 13:25:43 +02:00
Jesper Juhl
3cc6e78777 remoteproc: remove redundant NULL check before release_firmware()
release_firmware deals gracefully with NULL pointers, so checking
first is redundant.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-04-30 13:24:45 +02:00
Jesper Juhl
cf92549f1c qla2xxx: Remove redundant NULL check before release_firmware() call.
release_firmware() checks for NULL pointers internally so checking
before calling it is redundant.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-04-30 13:23:57 +02:00
Jesper Juhl
ee51f4432e aic94xx: Get rid of redundant NULL check before release_firmware() call
release_firmware() checks for NULL pointers internally, so checking
before calling the function is redundant.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-04-30 13:22:58 +02:00
Jesper Juhl
53c0ad522e tehuti: delete redundant NULL check before release_firmware()
release_firmware() checks for NULL pointers - no need to test before
the call.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-04-30 13:21:10 +02:00
Jesper Juhl
62baaf34dd qlogic: get rid of a redundant test for NULL before call to release_firmware()
Since release_firmware() deals gracefully with being passed a NULL
pointer there is no reason to test explicitly before calling the
function.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-04-30 13:20:06 +02:00
Jesper Juhl
294ca868ed bna: remove redundant NULL test before release_firmware()
release_firmware() does its own NULL test so explicit test before call
is unneeded.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-04-30 13:18:51 +02:00
Jesper Juhl
e3c5530b96 tg3: remove redundant NULL test before release_firmware() call
There is no need to test for a NULL pointer before calling
release_firmware - the function does that on its own.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-04-30 13:17:53 +02:00
Jesper Juhl
b2cbf2e31b typhoon: get rid of redundant conditional before all to release_firmware()
There's no need to test for a NULL pointer before calling
release_firmware() since the function does that check itself, so
remove the redundant test.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-04-30 13:16:45 +02:00
Jesper Juhl
c69a6ca1a4 radeon_cp: Remove unneeded tests for NULL before calling release_firmware()
release_firmware() does its own tests for NULL pointers so there's no
need to explicitly test before calling it.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-04-30 13:15:31 +02:00
Nicolas Ferre
028fdd87b7 hwrng: Kconfig - modify default state for atmel-rng driver
In order to prevent building the Atmel hw_random driver for each and every
configuration, add a "default" Kconfig state in relation with
CONFIG_ARCH_AT91.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2012-04-30 20:00:35 +10:00
Sebastian Andrzej Siewior
e6a3b5e288 usb: dwc3: ep0: add LPM handling
On device loading the driver enables LPM and the acceptance of U1 and U2
states. The [Set|Clear]Feature requests for "U1/U2" are forwarded
directly to the hardware and allow / forbid the initiation of the low
power links.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-04-30 11:31:21 +03:00
Vasanthakumar Thiagarajan
93b42cae16 ath6kl: Complete failed tx packet in ath6kl_htc_tx_from_queue()
Return status of ath6kl_htc_tx_issue() is ignored in
ath6kl_htc_tx_from_queue(), but failed tx packet is
is not cleaned up. To fix memory leak in this case, call
completion with error. Also, throw an error debug message
when tx fails in ath6kl_sdio_write_async() due to shortage
in bus request buffer.

kvalo: change the error message to WARN_ON_ONCE()

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-04-30 10:56:24 +03:00