Commit graph

153,333 commits

Author SHA1 Message Date
Huang, Xiong
5cbdcc2f49 atl1c: clear bit MASTER_CTRL_CLK_SEL_DIS in atl1c_pcie_patch
bit MASTER_CTRL_CLK_SEL_DIS could be set before enter suspend
clear it after resume to enable pclk(PCIE clock) switch to
low frequency(25M) in some circumstances to save power.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 20:14:20 -04:00
Huang, Xiong
7f5544d669 atl1c: refine reg definition of REG_MASTER_CTRL
refine/update register REG_MASTER_CTRL definition according with
hardware spec.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 20:14:20 -04:00
Huang, Xiong
95f9aea769 atl1c: clear PCIE error status in atl1c_reset_pcie
clear PCIE error status (error log is write-1-clear).
REG_PCIE_UC_SEVERITY is removed as it's a standard pcie register,
and using kernle API to access it.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 20:14:20 -04:00
Huang, Xiong
9c277d848d atl1c: remove dmar_dly_cnt and dmaw_dly_cnt
dmar_dly_cnt and dmaw_dly_cnt aren't used by hardware/driver any more.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 20:14:19 -04:00
Huang, Xiong
c08b9b2a5b atl1c: update right threshold for TSO
atl1c_configure_tx used a wrong value of MAX_TX_OFFLOAD_THRESH(9KB)
for TSO threshold.
the right value should be 7KB
Fast Ethernet controller doesn't support Jumbo frame.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 20:14:19 -04:00
Huang, Xiong
969a7ee2a8 atl1c: add module parameter for l1c_wait_until_idle
l1c_wait_until_idle is called for serval modules (TXQ/RXQ/TXMAC/RXMAC).
specific moudle have specific idle/busy status in reg REG_IDLE_STATUS.
the previous code return wrongly if all modules are in idle status,
regardless the 'stop' action is applied on individual module.
Refine the reg REG_IDLE_STATUS definition as well.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 20:14:19 -04:00
Huang, Xiong
9c5282180b atl1c: threshold for ASPM is changed based on chip capability
threshold setting to control ASPM for diff chips are different.
currently, all gigabit-capability chips have limited-ASPM under
100M throughput.

Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 20:14:19 -04:00
Giuseppe CAVALLARO
31ea38eefe stmmac: do not fail when probe and there is no csr clk defined
On some platforms, for example where we are doing the bring-up,
the csr clock is not passed from the framework and the Ethernet
device driver is failing when it can work w/o any issues and
using the default values. So this patch just warnings the case
of the csr clock cannot be acquired but w/o failing the probe
step. I have just tested it on ST STiH415 SoC (ARM).

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 20:09:06 -04:00
Giuseppe CAVALLARO
0f1f88a875 stmmac: verify the dma_cfg platform fields
Recently the dma parameters that can be passed from the platform
have been moved from the plat_stmmacenet_data to the stmmac_dma_cfg.

In case of this new structure is not well allocated the driver can
fails. This is an example how this field is managed in ST platforms

static struct stmmac_dma_cfg gmac_dma_setting = {
        .pbl = 32,
};

static struct plat_stmmacenet_data stih415_ethernet_platform_data[] = {
	{
		.dma_cfg = &gmac_dma_setting,
		.has_gmac = 1,
[snip]

This patch so verifies that the dma_cfg passed from the platform.
In case of it is NULL there is no reason that the driver has to fail
and some default values can be passed. These are ok for all the
Synopsys chips and could impact on performances, only.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
cc: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 20:08:59 -04:00
Francesco Virlinzi
4bfcbd7abc stmmac: Move the mdio_register/_unregister in probe/remove
This patch moves the mdio_register/_unregister in probe/remove
functions and this also is required when hibernation on disk
is done.

Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st,com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st,com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 20:08:49 -04:00
Francesco Virlinzi
3256251f98 stmmac: use custom init/exit functions in pm ops
Freeze and restore can call the custom init/exit functions.
Also the patch adds a custom data field that can be used
for storing platform data useful on restore the embedded
setup (e.g. GPIO, SYSCFG).

Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 20:08:44 -04:00
Rafal Prylowski
2b3c83efc9 dmaengine/ep93xx_dma: Implement double buffering for M2M DMA channels
Add double buffering support for M2M DMA channels. Implement this by using EP93xx
M2M DMA Buffer and Control Finite State Machines to be sure that we are not
disabling the channel when it's actually operating.

Signed-off-by: Rafal Prylowski <prylowski@metasoft.pl>
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
2012-04-20 08:37:19 +10:00
Greg Kroah-Hartman
cae18768ac USB: serial: ipaq: remove product and vendor module parameters
This driver is for devices that are no longer being made, so the ability
to add new device ids when loading the module is not a feature that
anyone uses anymore.  So remove it, which simplifies the startup code a
lot, and saves space.

If you still need to dynamically load device ids, that can be done
through sysfs.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-19 15:17:46 -07:00
Greg Kroah-Hartman
0bf4da35b5 USB: serial: visor: remove product and vendor module parameters
This driver is for devices that are no longer being made, so the ability
to add new device ids when loading the module is not a feature that
anyone uses anymore.  So remove it, which simplifies the startup code a
lot, and saves space.

If you still need to dynamically load device ids, that can be done
through sysfs.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-19 15:16:59 -07:00
David Spinadel
a104104fd7 iwlwifi: Remove inconsistent and redundant declaration
Remove declaration of iwl_alloc_traffic_mem from iwl-agn.h,
from methods that was exposed to support MVM.

MVM doesn't have to use this declaration.

CC: netdev@vger.kernel.org
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 16:55:14 -04:00
Hans Verkuil
f70cfc7f18 [media] vivi: fix duplicate line
This was inadvertently introduced when the integer menu control was added.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 17:24:53 -03:00
Hans Verkuil
ca57681195 [media] v4l2-ctrls.c: zero min/max/step/def values for 64 bit integers
Those fields are meaningless for such control types, and the control framework
should zero them. Otherwise v4l2-compliance will complain about non-zero
min/max/step/def fields.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 17:24:19 -03:00
Hans Verkuil
d1c754a932 [media] V4L2: drivers implementing vidioc_default should also return -ENOTTY
If the vidioc_default implementation doesn't support the ioctl, then drivers
must return -ENOTTY instead of -EINVAL.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 17:23:55 -03:00
Hans Verkuil
ee71e7b3ae [media] V4L: fix incorrect refcounting
Both radio-keene and dsbr100 did one v4l2_device_get too many. Thus the refcount
never became 0 and that causes a memory leak.

Also updated the V4L2 framework documentation accordingly.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 17:23:38 -03:00
Dan Carpenter
aa6d5f2953 [media] pluto2: remove some dead code
buf[] is a 4 character array.  Perhaps this was some debugging code from
back in the day?

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 17:15:32 -03:00
Marcos Paulo de Souza
c1341a16f6 [media] drivers: media: dvb: ddbridge: ddbridge-code: Remove unneeded include of version.h
The output of "make versioncheck" told us that the file
drivers/media/dvb/ddbridge/ddbridge-code.c has a incorrect include of
version.h:

linux/drivers/media/dvb/ddbridge/ddbridge-core.c: 34 linux/version.h not
needed.

After take a look in the code, we can agree to remove it.

Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 16:54:29 -03:00
Marcos Paulo de Souza
af22b83ab8 [media] drivers: media: radio: radio-keene.c: Remove unneeded include of version.h
The output of "make versioncheck" told us that:

drivers/media/radio/radio-keene.c: 31 linux/version.h not needed.

After take a look in the code, we can agree to remove it.

Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 16:54:16 -03:00
Marcos Paulo de Souza
713ca5dfd0 [media] drivers: media: video: adp1653.c: Remove unneeded include of version.h
The output of "make versioncheck" told us that:

drivers/media/video/adp1653.c: 37 linux/version.h not needed.

After we take a look at the code, we can afree to remove it.

Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 16:53:59 -03:00
Mauro Carvalho Chehab
f26cede165 [media] tm6000: don't use KERNEL_VERSION
As reported by Marcos:
> The output of "make versioncheck" told us that:
>
> drivers/staging/media/easycap/easycap_ioctl.c: 2442: need linux/version.h

Now that drivers/media/video/v4l2-ioctl.c fills cap->version:
	case VIDIOC_QUERYCAP:
	{
		struct v4l2_capability *cap = (struct v4l2_capability *)arg;

		if (!ops->vidioc_querycap)
			break;

		cap->version = LINUX_VERSION_CODE;

V4L2 drivers that use video_ioctl2() shouldn't initialize it anymore.

Reported-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 16:49:30 -03:00
Mauro Carvalho Chehab
d8a9c01484 [media] tlg2300: Remove usage of KERNEL_VERSION()
As reported by Marcos:

On 04-18-2012 01:30, Marcos Paulo de Souza wrote:
> The output of "make versioncheck" told us that:
>
> drivers/media/video/tlg2300/pd-video.c: 1669: need linux/version.h
>
> If we take a look at the code, we can see that this file uses the macro
> KERNEL_VERSION.

The V4L2 core now fills it automatically, so drivers shouldn't touch on
cap->version anymore.

Reported by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 16:47:07 -03:00
Giuseppe CAVALLARO
996f73937c icplus: fix interrupt for IC+ 101A/G and 1001LF
This patch fixes and adds the irq handler for the
IC+ 101A/G where we need to read the reg17 to clean
the irq.
Also remove the flag for the 1001LF where no interrupt
can be used for this device.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 15:34:18 -04:00
Bjørn Mork
3bc17d10c9 net: qmi_wwan: support Sierra Wireless MC77xx devices in QMI mode
The MC77xx devices can operate in two modes: "Direct IP" or "QMI",
switchable using a password protected AT command.  Both product ID
and USB interface configuration will change when switched.

The "sierra_net" driver supports the "Direct IP" mode.  This driver
supports the "QMI" mode.

There are also multiple possible USB interface configurations in each
mode, some providing more than one wwan interface.  Like many other
devices made for Windows, different interface types are identified
using a static interface number.  We define a Sierra specific
interface whitelist to support this.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 15:26:42 -04:00
Michal Kubeček
f31c7937c2 bonding: start slaves with link down for ARP monitor
Initialize slave device link state as down if ARP monitor is
active and net_carrier_ok() returns zero. Also shift initial
value of its last_arp_tx so that it doesn't immediately cause
fake detection of "up" state.

When ARP monitoring is used, initializing the slave device with
up link state can cause ARP monitor to detect link failure
before the device is really up (with igb driver, this can take
more than two seconds).

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 15:25:02 -04:00
Dan Carpenter
7e5998aa74 bnx2x: off by one in bnx2x_ets_e3b0_sp_pri_to_cos_set()
The sp_pri_to_cos[] array size depends on the config but lets say it is
BX_E3B0_MAX_NUM_COS_PORT0 and max_num_of_cos is also
DCBX_E3B0_MAX_NUM_COS_PORT0.  In the original code
"pri == max_num_of_cos" was accepted but it is one past the end of the
array.

Also we used "pri" before capping it.  It's a harmless read past the end
of the array, but it would affect which error message gets printed.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 15:22:44 -04:00
Michael Krufky
e631f57804 [media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmware
Rather than loading firmware specific for the xtal frequency, just use
the standard firmware and set the xtal frequency after firmware upload.

The modified firmware will never be released, so we're better off
merging this now rather than waiting for v3.5.

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 16:13:15 -03:00
Konrad Rzeszutek Wilk
186bab1ce0 xen/resume: Fix compile warnings.
linux/drivers/xen/manage.c: In function 'do_suspend':
linux/drivers/xen/manage.c:160:5: warning: 'si.cancelled' may be used uninitialized in this function

Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-19 15:12:49 -04:00
Linus Torvalds
19853301ef Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
 "It's like a grab bag of one liners:

  - core: fix page flip error path, reorder object teardown.
  - usb: fix the drm_usb module license.
  - i915: VT switch on SNB with non-native modes fix, and a regression
    fix from 3.3.
  - radeon: missing unreserve on SI, AGP/VRAM setup fix (fixes radeon on
    IA64, but its a generic bug), an rn50 regression from 3.3, turn off
    MSIs on rv515 (it loses rearms every so often)."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  nouveau: Set special lane map for the right chipset
  drm/radeon: fix load detect on rn50 with hardcoded EDIDs.
  drm: Releasing FBs before releasing GEM objects during drm_release
  drm/nouveau/pm: don't read/write beyond end of stack buffer
  drivers: gpu: drm: gma500: mdfld_dsi_output.h: Remove not unneeded include of version.h
  radeon: fix r600/agp when vram is after AGP (v3)
  drm: fix page_flip error handling
  drm/radeon/kms: fix the regression of DVI connector check
  drm/usb: fix module license on drm/usb layer.
  drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
  drm/i915: Hold mode_config lock whilst changing mode for lastclose()
  drm/radeon/si: add missing radeon_bo_unreserve in si_rlc_init() v2
  drm/radeon: disable MSI on RV515
  drm/i915: don't clobber the special upscaling lvds timings
2012-04-19 12:08:11 -07:00
Guennadi Liakhovetski
18311c5395 [media] V4L: mt9m032: fix compilation breakage
Fix the following compilation failure:

linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop':
linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop'
linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format':
linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format'
linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe':
linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove':
linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity'
make[4]: *** [drivers/media/video/mt9m032.o] Error 1

by adding a dependency on VIDEO_V4L2_SUBDEV_API.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 15:39:07 -03:00
viresh kumar
67b508715a ARM: 7392/1: CLKDEV: Optimize clk_find()
clk_find must return as soon as it gets the correct clock. Currently it check
all clocks until it found a lookup with both dev_id and con_id matching.

If only one of them is passed, then we don't actually need to wait for both of
them to match. We can quit as soon as the requested id (dev_id or con_id)
matches.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-04-19 19:34:26 +01:00
Mark Brown
a8a97db984 ARM: 7376/1: clkdev: Implement managed clk_get()
Allow clk API users to simplify their cleanup paths by providing a
managed version of clk_get() and clk_put().

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-04-19 19:34:18 +01:00
Linus Walleij
6026aa907b ARM: 7369/1: amba: add functions to add devices dynamically
Add two functions to add APB and AHB devices to the amba (PrimeCell)
bus dynamically. This is modeled after the static definition
macros recently introduced into <linux/amba/bus.h> and can
help us in factoring out a bunch of code across the kernel.
Since a lot of call sites seem to be using a returned struct
amba device* pointer, let's use that.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-04-19 19:31:33 +01:00
Gianluca Gennari
0bc9d39b8f [media] dib0700: add new USB PID for the Elgato EyeTV DTT stick
Reported working here:
http://ubuntuforums.org/archive/index.php/t-1510188.html
http://ubuntuforums.org/archive/index.php/t-1756828.html
https://sites.google.com/site/slackwarestuff/home/elgato-eyetv

Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 14:43:56 -03:00
Tim Gardner
d74185b40d [media] video: vicam: Add MODULE_FIRMWARE
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 14:40:09 -03:00
Tim Gardner
a020182ad6 [media] staging: go7007: Add MODULE_FIRMWARE
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 14:38:52 -03:00
Gianluca Gennari
a00f559c9f [media] dib7000p: remove duplicate code and comment
Remove duplicate code and comment, probably due to a patch applied twice.

Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19 14:35:57 -03:00
Dan Carpenter
716af4abd6 ksz884x: don't copy too much in netdev_set_mac_address()
MAX_ADDR_LEN is 32.  ETH_ALEN is 6.  mac->sa_data is a 14 byte array, so
the memcpy() is doing a read past the end of the array.  I asked about
this on netdev and Ben Hutchings told me it's supposed to be copying
ETH_ALEN bytes (thanks Ben).

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 13:25:03 -04:00
Konrad Rzeszutek Wilk
3066616ce2 xen/xenbus: Add quirk to deal with misconfigured backends.
A rather annoying and common case is when booting a PVonHVM guest
and exposing the PV KBD and PV VFB - as broken toolstacks don't
always initialize the backends correctly.

Normally The HVM guest is using the VGA driver and the emulated
keyboard for this (though upstream version of QEMU implements
PV KBD, but still uses a VGA driver). We provide a very basic
two-stage wait mechanism - where we wait for 30 seconds for all
devices, and then for 270 for all them except the two mentioned.

That allows us to wait for the essential devices, like network
or disk for the full 6 minutes.

To trigger this, put this in your guest config:

vfb = [ 'vnc=1, vnclisten=0.0.0.0 ,vncunused=1']

instead of this:
vnc=1
vnclisten="0.0.0.0"

CC: stable@kernel.org
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
[v3: Split delay in non-essential (30 seconds) and essential
 devices per Ian and Stefano suggestion]
[v4: Added comments per Stefano suggestion]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-19 12:45:01 -04:00
Henrik Rydberg
273a50fbcd nouveau: Set special lane map for the right chipset
The refactoring of the nv50 logic, introduced in 8663bc7c, modified the
test for the special lane map used on some Apple computers with Nvidia
chipsets. The tested MBA3,1 would still boot, but resume from suspend
stopped working. This patch restores the old test, which fixes the problem.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-04-19 16:37:53 +01:00
Dave Airlie
a09d431f34 drm/radeon: fix load detect on rn50 with hardcoded EDIDs.
When the force changes went in back in 3.3.0, we ended up returning
disconnected in the !force case, and the connected in when forced,
as it hit the hardcoded check.

Fix it so all exits go via the hardcoded check and stop spurious
modesets on platforms with hardcoded EDIDs.

Reported-by: Evan McNabb (Red Hat)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-04-19 16:02:18 +01:00
Prathyush
4e47e02d1a drm: Releasing FBs before releasing GEM objects during drm_release
During DRM release, all the FBs and gem objects are released. If
a gem object is being used as a FB and set to a crtc, it must not
be freed before releasing the framebuffer first.

If FBs are released first, the crtc using the FB is disabled first
so now the GEM object can be freed safely. The CRTC will be enabled
again when the driver restores fbdev mode.

Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-04-19 14:40:41 +01:00
Jim Meyering
5799d9e2ea drm/nouveau/pm: don't read/write beyond end of stack buffer
NUL-terminate after strncpy.

If the parameter "profile" has length 16 or more, then strncpy
leaves "string" with no NUL terminator, so the following search
for '\n' may read beyond the end of that 16-byte buffer.
If it finds a newline there, then it will also write beyond the
end of that stack buffer.

Signed-off-by: Jim Meyering <meyering@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-04-19 14:38:54 +01:00
Marcos Paulo de Souza
5edaad8700 drivers: gpu: drm: gma500: mdfld_dsi_output.h: Remove not unneeded include of version.h
The output of "make versioncheck" points a incorrect include of
version.h in the drivers/gpu/drm/gma500/mdfld_dsi_output.h:

drivers/gpu/drm/gma500/mdfld_dsi_output.h: 32 linux/version.h not needed.

If we take a look in the file, we can agree to remove it.

Cc: David Airlie <airlied@linux.ie>
Cc: <dri-devel@lists.freedesktop.org>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-04-19 14:38:02 +01:00
Jerome Glisse
dfc6ae5bd7 radeon: fix r600/agp when vram is after AGP (v3)
If AGP is placed in the middle, the size_af is off-by-one, it results
in VRAM being placed at 0x7fffffff instead of 0x8000000.

v2: fix the vram_start setup.
v3: also fix r7xx & newer ASIC

Reported-by: russiane39 on #radeon

Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-04-19 14:37:42 +01:00
Joonyoung Shim
aef6a7eeac drm: fix page_flip error handling
Free event and restore event_space only when page_flip->flags has
DRM_MODE_PAGE_FLIP_EVENT if page_flip() is failed.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-04-19 14:36:51 +01:00
Dave Airlie
d6b8395262 Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
  drm/i915: Hold mode_config lock whilst changing mode for lastclose()
  drm/i915: don't clobber the special upscaling lvds timings
2012-04-19 14:13:52 +01:00