SM8150 has (at least) two GPU speed bins. With the support added on the
driver side, wire up bin detection in the DTS to restrict lower-quality
SKUs from running at frequencies they were not validated at.
Tested-by: Marijn Suijten <marijn.suijten@somainline.org> # On Sony Xperia 5 (speed bin 0x3)
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230331-topic-konahana_speedbin-v3-4-2dede22dd7f7@linaro.org
Now that there's display support, there is no reason to assume the default
mode for Adreno should be headless. Keep it like that for boards that
previously enabled it, so as not to create regressions though.
Tested-by: Marijn Suijten <marijn.suijten@somainline.org> # On Sony Xperia 5
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230331-topic-konahana_speedbin-v3-3-2dede22dd7f7@linaro.org
Add the initial device tree support for the Reference Design
Platform(RDP) 468 based on IPQ5332 family of SoCs. This patch carries the
support for Console UART, SPI NOR, eMMC.
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323093120.20558-3-quic_kathirav@quicinc.com
The DSI OPP table on SDM630 is used by one DSI0, but on SDM660 is shared
by two nodes (DSI0 and DSI1), thus it should be rather in top-level, not
in DSI0.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407192605.168666-1-krzysztof.kozlowski@linaro.org
Add a node for RMTFS and associate it with MSA and NAV IDs to enable
modem functionality on SM6115.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406-topic-lenovo_features-v2-2-625d7cb4a944@linaro.org
Bindings require pin configuration nodes to have the function, even if
it is GPIO:
msm8916-thwc-ufi001c.dtb: pinctrl@1000000: sim-ctrl-default-state: 'oneOf' conditional failed, one must be fixed:
'esim-sel-pins', 'sim-en-pins', 'sim-sel-pins' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324202244.744271-1-krzysztof.kozlowski@linaro.org
Add nodes for remoteproc, smp2p and smsm in preparation
for audio support on this platform.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407165345.42800-4-a39.skl@gmail.com
Add nodes for remoteproc, smp2p and smsm to make it possible to use
modem functionality on this platform.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407165345.42800-3-a39.skl@gmail.com
Add nodes for remoteproc, smp2p and smsm to make it possible to use
wifi/bt functionality on this platform.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407165345.42800-2-a39.skl@gmail.com
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180655.128771-2-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180655.128771-1-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180045.126952-1-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-10-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-9-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-8-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-7-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-6-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-5-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-4-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-3-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-2-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-1-krzysztof.kozlowski@linaro.org
Add support for the Xiaomi Mi A3 (xiaomi-laurel-sprout). Here's a
summary on what's defined.
- dmesg output to bootloader preconfigured display
- USB
- UFS
- SD card
- SMD RPM regulators
- Volume Up, Down and Power buttons
- Thermistors
Signed-off-by: Lux Aliaga <they@mint.lgbt>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306170817.3806-7-they@mint.lgbt
Add support for the Xiaomi Mi Pad 5 Pro CSOT variant. The CSOT variant
uses China Star Optoelectronics Technology (CSOT) panel based on NT36523
display controller.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-3-lujianhua000@gmail.com
Add nodes for BOE NT36523 panel found in xiaomi-elish. This panel
is a dual dsi mode panel and the dsi phy type is cphy.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-2-lujianhua000@gmail.com
There are two panel variants of xiaomi-elish, BOE and CSOT panels.
In order to support both panels, so split elish dts into common dtsi
and elish-boe dts.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-1-lujianhua000@gmail.com
Add an initial device tree for the QTI RB1 development board, based on
the QRB2210 (QCM2290 derivative) SoC. This device tree targets the SoM
revision 4, a.k.a. the Mass Production SKU.
To get a successful boot, run:
cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/qrb2210-rb1.dtb >\
.Image.gz-dtb
mkbootimg \
--kernel .Image.gz-dtb \
--ramdisk some_initrd \
--output rb1-boot.img \
--pagesize 4096 \
--base 0x8000 \
--cmdline 'some cmdline'
fastboot boot rb1-boot.img
There's no dtbo or other craziness to worry about.
For the best dev experience, you can erase boot and use fastboot boot
everytime, so that the bootloader doesn't mess with you.
If you have a SoM revision 3 or older (there should be a sticker on it
with text like -r00, where r is the revision), you will need to apply
this additional diff:
aliases {
- serial0 = &uart0;
+ serial0 = &uart4;
/* UART connected to the Micro-USB port via a FTDI chip */
- &uart0 {
+ &uart4 {
That should however only concern preproduction boards.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230403-topic-rb1_qcm-v2-5-dae06f8830dc@linaro.org
Add an initial device tree for the QCM2290 low-end SoC, featuring 4
"customized" Cortex-A53 cores and up to 4 GiB of LPDDR(3/4X).
This revision brings support for:
- TSENS & thermal zones
- SDHCI1/2
- I2C, SPI, UART
- MPSS
- ADSP
- Wi-Fi
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230403-topic-rb1_qcm-v2-3-dae06f8830dc@linaro.org
Drop the qcom,snoc-host-cap-skip-quirk that was never introduced to
solve schema warnings.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406-topic-ath10k_bindings-v3-2-00895afc7764@linaro.org
Enable the SLPI DSP on the SHIFTPHONES SHIFT6mq phone with a
Qualcomm SDM845 SoC.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-6-me@dylanvanassche.be
Enable the SLPI DSP on the Oneplus 6 phone with a Qualcomm SDM845 SoC.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-5-me@dylanvanassche.be
Qualcomm SDM845 SoC features a SLPI DSP which uses FastRPC through
an allocated memory region to load files from the host filesystem
such as sensor configuration files.
Add a FastRPC node at /dev/fastrpc-sdsp and a DMA region, similar to
downstream, to allow userspace to communicate with the SLPI via the
FastRPC interface for initializing the sensors on the SLPI.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-4-me@dylanvanassche.be
SSC_Q6 and ADSP_Q6 are used in the FastRPC driver for accessing
the secure world.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-3-me@dylanvanassche.be
