Add definition and parsing for wifi 7 extended fields. These fields
include hardware index which is current reporting, timestamp and self
defined sequences for debug purposes.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126063356.17857-2-pkshih@realtek.com
The chip_ops::fem_setup is to get if a hardware module type contains PA
and LNA that will affect how RF calibrations do. The chip_ops::rfe_gpio
is to set GPIO PIN MUX according to hardware module type too. 8922A
doesn't have these special module types yet, so leave them as NULL.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033813.12562-1-pkshih@realtek.com
Get thermal value as a clue to do RF calibration if the delta is larger
than a threshold, but 8922A doesn't need this, so we only read out the
value when debugging to reduce IO.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033802.12508-1-pkshih@realtek.com
Implement indirect interface v2 to read/write RF registers via PHY
registers for 8922A.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033637.12330-5-pkshih@realtek.com
This function is to set TX/RX path. Especially for 1SS rate, it can select
to TX on one or two antenna. Before this operation, stop hardware to
prevent transmitting/receiving unexpected packets. After that, restore
settings and reset hardware to prevent it stays on abnormal state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033637.12330-4-pkshih@realtek.com
To set TX/RX path or set channel, we need these helpers to stop TX and
restore settings. The sch_tx stands for scheduler TX channel, and the
cfg_ppdu is to stop reporting PPDU status, so we should stop them during
setting.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033637.12330-3-pkshih@realtek.com
Hook implemented handlers to chip_ops, and fill packet frequency and signal
strength to RX status from RX PPDU status packet.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033637.12330-2-pkshih@realtek.com
Hardware puts RX descriptor and packet in RX DMA buffer, so it could be
over one buffer size if packet size is 11454, and then it will be split
into two segments. WiFi 7 chips use larger size of RX descriptor, so
enlarge DMA buffer size according to RX descriptor to have better
performance and simple flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240121071826.10159-5-pkshih@realtek.com
PCI RX ring is a kind of read/write index ring, and DMA and ring index are
asynchronous, so suddenly driver gets newer index ahead before DMA. To
resolve this rare situation, we use a RX tag as helpers to make sure DMA
is done.
The RX tag is a 13-bit value, and range is from 1 ~ 0x1FFF, but 0 isn't
used so should be skipped.
Only enable this validation to coming WiFi 7 chips, because existing
chips use different design and don't really meet this situation.
Add missed rx_ring_eq_is_full for 8851BE by the way.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240121071826.10159-4-pkshih@realtek.com
During SER (system error recovery), expect to deal with
only ISR related to halt. So, refine IMR configuration.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240121071826.10159-3-pkshih@realtek.com
Be higher resolution of SER timer unit from 32ms to 16ms to detect
abnormal situation more accurately, and set hardware watchdog timer to 4ms.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240121071826.10159-2-pkshih@realtek.com
The driver found its inception a little after the year 201. According
git blame output it was added in 2016 so lets go with that.
Fixes: 4d79289598 ("brcmfmac: switch to new platform data")
Reported-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240128093057.164791-3-arend.vanspriel@broadcom.com
We have new features for both ath11k and ath12k. ath12k is now under
heavy refactoring in preparation for MLO support.
Major changes:
ath12k
* refactoring in preparation for Multi-Link Operation (MLO) support
* 1024 Block Ack window size support
* provide firmware wmi logs via a trace event
ath11k
* 36 bit DMA mask support
* support 6 GHz station power modes: Low Power Indoor (LPI), Standard
Power) SP and Very Low Power (VLP)
-----BEGIN PGP SIGNATURE-----
iQFLBAABCgA1FiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmW49dUXHHF1aWNfa3Zh
bG9AcXVpY2luYy5jb20ACgkQbhckVSbrbZsGagf+PmejP9HDXTB8RmL0exK79XyJ
DDn2a1elnnUNwf1SLrRTVZ83dtoN2V48A4/xQUhNfjs7vDUvvRj/vbUx2pe3CGoJ
9qUMO2/U7KxfEb4wo+iib51lD4B00/QaQIqC/nKY6xc85GIdUEdIfMXyEN2OF0Zz
BYEILiQtRdWYWmemesVv7goumpSEsReIdoETwMdVze8/geOluiy6UCBW7bh6BAi8
U9aaDEZuPfuvCWCWeCWNTN+xJNHSdLsdjSPZD+zq0jLHcuD1GmDJYQ5r67ZvUjM+
rS39DnJrDtTfiGMwIieGOy2zSCZZSVlyjFJuL9+P0X5N8A5057YIa+CZjeLCpw==
=mU6W
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20240130' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath
ath.git patches for v6.9
We have new features for both ath11k and ath12k. ath12k is now under
heavy refactoring in preparation for MLO support.
Major changes:
ath12k
* refactoring in preparation for Multi-Link Operation (MLO) support
* 1024 Block Ack window size support
* provide firmware wmi logs via a trace event
ath11k
* 36 bit DMA mask support
* support 6 GHz station power modes: Low Power Indoor (LPI), Standard
Power) SP and Very Low Power (VLP)
Add cfg80211, mac80211 and iwlwifi to the all_tests config
so that the unit tests (enabled by KUNIT_ALL_TESTS) will be
run by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This *mostly* reverts commit 1e1b11b6a1 ("nl80211/cfg80211: Specify
band specific min RSSI thresholds with sched scan").
During the review of a new patch [1] it was observed that the
functionality being modified was not actually being used by any
in-tree driver. Further research determined that the functionality was
originally introduced to support a new Android interface, but that
interface was subsequently abandoned. Since the functionality has
apparently never been used, remove it. However, to mantain the
sanctity of the UABI, keep the nl80211.h assignments, but clearly mark
them as obsolete.
Cc: Lin Ma <linma@zju.edu.cn>
Cc: Vamsi Krishna <quic_vamsin@quicinc.com>
Link: https://lore.kernel.org/linux-wireless/20240119151201.8670-1-linma@zju.edu.cn/ [1]
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240125-for-next-v1-1-fd79e01c6c09@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wiphy_work infra ensures that the entire worker will run
with the wiphy mutex. It is useful to have RX handlers
running as a wiphy_work, when we don't want the handler to
run in parallel with mac80211 work (to avoid races).
For example - BT notification can disable eSR starting from the next
patch.
In ieee80211_set_active_links we first check that eSR is
allowed, (drv_can_activate_links) and then activate it.
If the BT notif was received after drv_can_activate_links
(which returned true), and before the activation - eSR will be
activated when it shouldn't.
If BT notif is handled with the wiphy mutex, it can't run in
parallel to ieee80211_set_active_links, which also holds that
mutex.
Add the necessary infrastructure here, for use in the next commit.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240123200528.ce83d16cdec8.I35ef53fa23f58b9ec17924099238b61deafcecd7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This callback checks if a given bitmap of active_links
will be supported by the driver or not.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240123200528.a26fd48bfe3d.I03ae6b4c7fd24e8701660a68cec9403dc3469a0e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This command version adds two news fields:
sbb_bandwidth and sbb_ctrl_channel_loc
They will be populated later.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.82ab4140fff9.Icfba4819fe0b7ac8219ab671c632e25f5fbbaf6f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Without SMP the function is just a stub that returns an error code. Add
a compile time check for CONFIG_SMP in the interest of not logging an
error if setting affinity is not possible anyway.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.ed9094390731.Ic4e5e019c01fd4231b99cf4919af5d19d6353869@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should - at least for now - advertise common nominal packet
padding of 16µs instead of the more specific PPE thresholds.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.4312e176dfdc.Ide75980ff57257a31e86e6ac5948a8f97aaab577@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link ID in time event data is -1 when the time event is cleared.
Change the type of the link ID in the time event data structure
and in the affected function from unsigned to signed.
Fixes: 1350658373 ("wifi: iwlwifi: support link_id in SESSION_PROTECTION cmd")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240123200528.50d4941f946c.Iea990b118c69bc3e1eb61c1d134c9d470b3a17ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's either the pldr_sync case, in which case we didn't want
or do the retry loops anyway, or things will just continue to
fail. Remove the retry loop that was added in a previous attempt
to address the issue that was later (though still a bit broken)
addressed by the pldr_sync case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.f80a88a18799.I48f21eda090f4cc675f40e99eef69a986d21b500@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the STEP (the interface between MAC and PHY) is in URM
(a lower speed mode) then we cannot use 320 MHz MCS > 9.
Therefore, limit the MCS in our capabilities in this case.
Note that this also limits the TX/rate scaling since that
takes both TX and RX capabilities into account.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.02bae683b7fc.Id5efbb71d45da02c8c4e211d20396637ddd44da8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver should not send 160 MHz BW support for 5 GHz
band in HE if PCI subsystem device ID indicates no 160 MHz support.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Reviewed-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240126085924.77c248ce6986.I558e8d0cf19dc862b1c4124df78a4cb690095bb2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to print this, it's a known issue and
the workaround works just fine. Make the reallocation
message just a debug message.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.329d5f2ee7f7.I0bfc6dde17fe2c738129f3aba746c6cba57589f9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the new 802.11be device with limites capabilities:
- 320 MHz isn't supported
- MCSs 12 and 13 are not supported
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.8529bd2acedf.I25dccb7bbeb21b8df2123fad51dde7fcf137a508@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We used to have a test built into the code for this internally,
but now we can put that into kunit and let everyone run it, to
verify the devinfo table ordering if it's changed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.a4a8af7c091f.I0fb09083317b331168b99b8db39656a126a5cc4d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch makes duration in scan request be applicable when using
SW scan, but only accepts durations greater than the default value for
the following reasons:
1. Most APs have a beacoon interval of 100ms.
2. Sending and receiving probe require some delay.
3. Setting channel to HW also requires some delays
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Link: https://msgid.link/20240123054752.22833-1-michael-cy.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This does not change anything effectively, but it is closer to what the
code is trying to achieve here. i.e. select the link data if it is an
MLD and fall back to using the deflink otherwise.
Fixes: 0f99f08783 ("wifi: mac80211: Print local link address during authentication")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.4c4b1c40eb3c.I2771621dee328c618536596b7e56232df42a79c8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When parsing 6 GHz operation, don't set the bss_conf
values. We only commit to that later in association,
so move the code there. Also clear it later.
While at it, handle IEEE80211_6GHZ_CTRL_REG_VLP_AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.c2da4bc515e8.I219ca40e15c0fbaff0e7c3e83ca4b92ecbc1f8ae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To simplify the code in the next patch, disallow drivers
supporting 40 MHz in HT but not HE, since we'd otherwise
have to track local maximum bandwidth per mode there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.da15fe3214d2.I4df51ad2f4c844615c168bf9bdb498925b3c77d4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For verifying the required HE capabilities are supported
locally, we access the HE capability element of the AP.
Simplify that access, we've already parsed and validated
it when parsing elements.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.2ef62b43caeb.I8baa604dd3f3399e08b86c99395a2c6a1185d35d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We already parse all the BSS elements into elems, there's
really no need to separately find EHT/ML again. Remove the
extra code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.c4a55da9f778.I112b1ef00904c4183ac7644800f8daa8a4449875@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only user of this function passes a lot of pointers
directly from the parsed elements, so it's simpler to
just pass the entire elements parsing struct. This also
shows that the ht_cap is actually unused.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.f0653cd5e7dd.I8bd5ee848074029a9f0495c95e4339546ad8fe15@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertise MLD capabilities and operations in AP mode that
say that up to 15 links are supported simultaneously.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.52a1d48b67e6.Ie459df742944d24d6401683d54d2f3ac44834803@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When going into an MLO connection, validate that the link IDs
match what userspace indicated, and that the AP MLD addresses
and capabilities are all matching between the links.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.ff83c034cb9a.I9962db0bfa8c73b37b8d5b59a3fad7f02f2129ae@changeid
[roll in extra fix from Miri to actually check the return value]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The association response is more likely to be correct
than a random scan result, which really also should be
correct, but we generally prefer to take data from the
association response, so do that here as well.
Also reset the data so it doesn't hang around from an
old connection to a non-MLO connection, drivers would
hopefully not look at it, but less surprise this way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.1d10f1d1dbab.I545e955675e2269a52496a22ae7822d95b40235e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertise EMLSR and EMLMR capability on the AP side to be
a better compliant AP MLD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.dc8786efa787.Ic460c13a91d770c208ac16d0b3e94941bab9b8eb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If software crypto is used, simply add support for SPP A-MSDUs
(and use it whenever enabled as required by the cfg80211 API).
If hardware crypto is used, leave it up to the driver to set
the NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT flag and then check
sta->spp_amsdu or the IEEE80211_KEY_FLAG_SPP_AMSDU key flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.b8ada4514e2b.I1ac25d5f158165b5a88062a5a5e4c4fbeecf9a5d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add SPP (signaling and payload protected) AMSDU support.
Since userspace has to build the RSNX element, add an extended
feature flag to indicate that this is supported.
In order to avoid downgrade/mismatch attacks, add a flag to the assoc
command on the station side, so that we can be sure that the value of
the flag comes from the same RSNX element that will be validated by
the supplicant against the 4-way-handshake. If we just pulled the
data out of a beacon/probe response, we could theoretically look an
RSNX element from a different frame, with a different value for this
flag, than the supplicant is using to validate in the
4-way-handshake.
Note that this patch is only geared towards software crypto
implementations or hardware ones that can perfectly implement SPP
A-MSDUs, i.e. are able to switch the AAD construction on the fly for
each TX/RX frame.
For more limited hardware implementations, more capability
advertisement would be required, e.g. if the hardware has no way
to switch this on the fly but has only a global configuration that
must apply to all stations.
The driver could of course *reject* mismatches, but the supplicant
must know so it can do things like not negotiating SPP A-MSDUs on
a T-DLS link when connected to an AP that doesn't support it, or
similar.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.fadac8df7030.I9240aebcba1be49636a73c647ed0af862713fc6f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertise support for negotiated TTLM in AP mode for testing
purposes. In addition, declare support for some extended
capabilities that are globally advertised by mac80211.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.3f54382f8449.I42b2f7c52f7574448cc8da3ad3db45075e4e0baa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update neg_ttlm and active_links according to the new mapping,
and send a negotiated TID-to-link map request with the new mapping.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.eeb385d771df.I2a5441c14421de884dbd93d1624ce7bb2c944833@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Same as in BSS_CHANGED_VALID_LINKS, set the active
links to all the usable links.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.3c28da3534e9.I76846c5dd693f930d4828e411c734639708b5a1a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Accept the request if all TIDs are mapped to the same link set,
otherwise reject it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.dfa8e132d0cd.I5fbec1fef933980819ea39c1227f37d307ab1145@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An MLD may send TID-to-Link mapping request frame to negotiate
TID to link mapping with a peer MLD.
Support handling negotiated TID-to-Link mapping request frame
by parsing the frame, asking the driver whether it supports the
received mapping or not, and sending a TID-to-Link mapping response
to the AP MLD.
Theoretically, links that became inactive due to the received TID-to-Link
mapping request, can be selected to be activated but this would require
tearing down the negotiated TID-to-Link mapping, which is still not
supported.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.0bc1a24fcc9d.Ie72e47dc6f8c77d4a2f0947b775ef6367fe0edac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the relevant definitions and structures for TID to Link mapping
negotiation request/response/teardown according to P802.11be_D4.0.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.9ef2b866c8c7.Ieaf7dadea9961e0edc55d19c99f0f9fbae591de6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the reporting AP is part of the same MLD, then an entry in the RNR is
required in order to discover it again from the BSS generated from the
per-STA profile in the Multi-Link Probe Response.
We need this because we do not have a direct concept of an MLD AP and
just do the lookup from one to the other on the fly if needed. As such,
we need to ensure that this lookup will work both ways.
Fixes: 2481b5da9c ("wifi: cfg80211: handle BSS data contained in ML probe responses")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.4cb3dbb1d84f.I7c74edec83c5d7598cdd578929fd0876d67aef7f@changeid
[roll in off-by-one fix and test updates from Benjamin]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In 'cfg80211_michael_mic_failure()', avoid extra call to 'strlen()'
by using the value returned by 'sprintf()'. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://msgid.link/20240110054246.371651-1-dmantipov@yandex.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
