[ Upstream commit b38dd256e1 ]
Unlike the phone SoCs this was copied from, x1e has a 40-bit physical bus.
The upper address space is used to support more than 32GB of memory.
This fixes issues when DMA buffers are allocated outside the 36-bit range.
Fixes: af16b00578 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251127212943.24480-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bfb696ccd ]
On SDM845 SPI uses hardware-provided chip select, while specifying
cs-gpio makes the driver request GPIO pin, which on DB845c conflicts
with the normal host controllers pinctrl entry.
Drop the cs-gpios property to restore SPI functionality.
Fixes: cb29e7106d ("arm64: dts: qcom: db845c: Add support for MCP2517FD")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260106-wcn3990-pwrctl-v2-7-0386204328be@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5dc4812f6 ]
Follow commit 9c92d36b0b ("arm64: dts: qcom: qrb2210-rb1: Fix UART3
wakeup IRQ storm") and apply the similar fix to the RB2 platform.
Having RX / TX pins as pull up and wakup interrupt as high-level
triggered generates an interrupt storm when trying to suspend the
device. Avoid the storm by using the falling edge trigger (as all other
platforms do).
Fixes: cab60b1665 ("arm64: dts: qcom: qrb4210-rb2: Enable bluetooth")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260106-wcn3990-pwrctl-v2-6-0386204328be@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c941feaa3 ]
The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.
Assign the clock to make sure it is properly configured
Fixes: 8a6b3ca2d3 ("arm64: dts: meson: g12a: add SDIO controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-6-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be2ff5fdb0 ]
The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.
Assign the clocks to make sure they are properly configured
Fixes: 4759fd87b9 ("arm64: dts: meson: g12a: add mmc nodes")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-5-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4067065590 ]
The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.
Assign the clocks to make sure they are properly configured
Fixes: 50662499f9 ("ARM64: dts: meson-gx: Use correct mmc clock source 0")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-4-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13d3fe2318 ]
The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.
Assign the clocks to make sure they are properly configured
Fixes: 221cf34bac ("ARM64: dts: meson-axg: enable the eMMC controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-3-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69330fd236 ]
The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.
Assign the clocks to make sure they are properly configured
Fixes: 520b792e83 ("arm64: dts: amlogic: add some device nodes for C3")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-1-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bd4edd67b ]
Although unlikely, devm_pm_runtime_enable() can fail due to memory
allocations. Without proper error handling, the subsequent
pm_runtime_resume_and_get() call may operate on incorrectly
initialized runtime PM state.
Add error handling to check the return value of
devm_pm_runtime_enable() and return on failure.
Fixes: 25f7d74d45 ("hwspinlock: omap: Use devm_pm_runtime_enable() helper")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20251124104805.135-1-vulab@iscas.ac.cn
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61acc4428a ]
Each A72 core has one watchdog instance associated with it. Since j742s2
has 4 A72 cores, the common file should not define 8 watchdog instances.
Refactor the last 4 extra watchdogs from the common file to j784s4
specific file, as j784s4 has 8 A72 cores and thus hardware description
requires 8 watchdog instances.
Fixes: 9cc161a450 ("arm64: dts: ti: Refactor J784s4 SoC files to a common file")
Signed-off-by: Abhash Kumar Jha <a-kumar2@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://patch.msgid.link/20260112085113.3476193-3-a-kumar2@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24c9d5fb8b ]
The device tree nodes should be ordered by unit addresses in ascending
order.
Correct the order by moving the c71_3 DSP node at the end as it has a
higher unit address.
Signed-off-by: Abhash Kumar Jha <a-kumar2@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://patch.msgid.link/20260112085113.3476193-2-a-kumar2@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Stable-dep-of: 61acc4428a ("arm64: dts: ti: k3-j784s4-j742s2-main-common.dtsi: Refactor watchdog instances for j784s4")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a115d4292 ]
MMC A and C are mis-represented as having their "clkin0" input connected to
xtal while it is actually connected to the MMC clock, probably in an
attempt to provide 24MHz to the device on this input.
Fix this and assign the clock to 24MHz to actually provide the required
rate.
Fixes: 3ab9d54b5d ("arm64: dts: amlogic: enable some device nodes for S4")
Tested-by: Nick Xie <nick@khadas.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-s4-mmc-fixup-v3-2-a4d3e136b3f2@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86124a8bec ]
The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.
This assumption did hold true until but it now, but it is apparently
not the case with s4. The clock has been reported to provide 1GHz
instead. This is most likely due to how the bootloader is using the MMC
clock on this platform.
Regardless of why the MMC clock rate is 1GHz, if the MMC driver expects
24MHz, the clock should be properly assigned, so assign it.
Reported-by: Nick Xie <nick@khadas.com>
Closes: https://lore.kernel.org/linux-amlogic/20260113011931.40424-1-nick@khadas.com/
Fixes: 3ab9d54b5d ("arm64: dts: amlogic: enable some device nodes for S4")
Tested-by: Nick Xie <nick@khadas.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-s4-mmc-fixup-v3-1-a4d3e136b3f2@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71630e581a ]
Motor Control PWM depends on its own supply clock, the clock gate control
is present in TIMCLK_CTRL1 register.
Fixes: b7d41c937e ("ARM: LPC32xx: Add the motor PWM to base dts file")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65ae9ea77e ]
Since commit 4cd2f417a0 ("dt-bindings: pwm: Convert lpc32xx-pwm.txt
to yaml format") both types of PWM controlles on NXP LPC32xx SoC
fairly gained 3 cells, reflect it in the platform dtsi file.
The change removes a dt binding checker warning:
mpwm@400e8000: #pwm-cells:0:0: 3 was expected
Cc: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Stable-dep-of: 71630e581a ("arm: dts: lpc32xx: add clocks property to Motor Control PWM device tree node")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6259094ee8 ]
In svs_enable_debug_write(), the buf allocated by memdup_user_nul()
is leaked if kstrtoint() fails.
Fix this by using __free(kfree) to automatically free buf, eliminating
the need for explicit kfree() calls and preventing leaks.
Fixes: 13f1bbcfb5 ("soc: mediatek: SVS: add debug commands")
Co-developed-by: Jianhao Xu <jianhao.xu@seu.edu.cn>
Signed-off-by: Jianhao Xu <jianhao.xu@seu.edu.cn>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
[Angelo: Added missing cleanup.h inclusion]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fbc09eb0b ]
Commit 74e19ef0ff ("uaccess: Add speculation barrier to
copy_from_user()") added a redundant barrier_nospec() in
copy_from_user(), because powerpc is already calling
barrier_nospec() in allow_read_from_user() and
allow_read_write_user(). But on other architectures that
call to barrier_nospec() was missing. So change powerpc
instead of reverting the above commit and having to fix
other architectures one by one. This is now possible
because barrier_nospec() has also been added in
copy_from_user_iter().
Move barrier_nospec() out of allow_read_from_user() and
allow_read_write_user(). This will also allow reuse of those
functions when implementing masked user access which doesn't
require barrier_nospec().
Don't add it back in raw_copy_from_user() as it is already called
by copy_from_user() and copy_from_user_iter().
Fixes: 74e19ef0ff ("uaccess: Add speculation barrier to copy_from_user()")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/f29612105c5fcbc8ceb7303808ddc1a781f0f6b5.1766574657.git.chleroy@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b2761eb12 ]
The P66's device tree includes the reference design dtsi files, which
defines a node and properties for the touchpanel in the common design.
The P66 dts file then overrides all the properties to match its own
design, but as the touchpanel model is different, a different schema
is matched. This other schema uses a different name for the GPIO.
The original submission added the correct GPIO property, but did not
delete the one inherited from the reference design, causing validation
errors.
Explicitly delete the incorrect GPIO property.
Fixes: 2a53aff272 ("ARM: dts: sun5i: Enable touchscreen on Utoo P66")
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251225103616.3203473-4-wens@kernel.org
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7db5fbe508 ]
Trivial change, Analog Devices vendor prefix is "adi", but there is
a valid "ad" vendor prefix of another company, this may explain why
the issue hasn't been discovered by the automatic tests.
A problem of not described compatible value is out of this change scope.
Fixes: c636eeb751 ("arm64: dts: qcom: msm8994-octagon: Add AD7147 and APDS9930 sensors")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251226003923.3341904-1-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3af51501e2 ]
It seems the USB combo SS1 and SS2 ref clocks have another gate, unlike
the SS0. These gates are part of the TCSR clock controller.
At least on Dell XPS 13 (9345), if the ref clock provided by the TCSR
clock controller for SS1 PHY is disabled on the clk_disable_unused late
initcall, the PHY fails to initialize. It doesn't happen on the SS0 PHY
and the SS2 is not used on this device.
This doesn't seem to be a problem on CRD though. It might be that the
RPMh has a vote for it from some other consumer and does not actually
disable it when ther kernel drops its vote.
Either way, these TCSR provided clocks seem to be the correct ones for
the SS1 and SS2, so use them instead.
Fixes: 4af46b7bd6 ("arm64: dts: qcom: x1e80100: Add USB nodes")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Taniya Das <taniya.das@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251103-dts-qcom-x1e80100-fix-combo-ref-clks-v1-1-f395ec3cb7e8@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad33ee060b ]
This regulator is used only for the display, which is enabled by the
bootloader and left on for continuous splash. Mark it as such.
Fixes: 288ef8a426 ("arm64: dts: sdm845: add oneplus6/6t devices")
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251118-dts-oneplus-regulators-v2-3-3e67cea1e4e7@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9b98b9dad ]
The touchscreen isn't enabled by bootloader and doesn't need to be
enabled at boot, only when the driver probes, thus remove the
regulator-boot-on property.
Fixes: 288ef8a426 ("arm64: dts: sdm845: add oneplus6/6t devices")
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251118-dts-oneplus-regulators-v2-1-3e67cea1e4e7@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e814796dfc ]
Historically sdm630.dtsi has used 1 byte length for the gpu_speed_bin
cell, although it spans two bytes (offset 5, size 7 bits). It was being
accepted by the kernel because before the commit 7a06ef7510 ("nvmem:
core: fix bit offsets of more than one byte") the kernel didn't have
length check. After this commit nvmem core rejects QFPROM on sdm630 /
sdm660, making GPU and USB unusable on those platforms.
Set the size of the gpu_speed_bin cell to 2 bytes, fixing the parsing
error. While we are at it, update the length to 8 bits as pointed out by
Alexey Minnekhanov.
Fixes: b190fb0106 ("arm64: dts: qcom: sdm630: Add sdm630 dts file")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Link: https://lore.kernel.org/r/20251211-sdm630-fix-gpu-v2-1-92f0e736dba0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e07ebe744 ]
When devm_platform_ioremap_resource() fails, it returns various
error codes. Returning a hardcoded -ENOMEM masks the actual
failure reason.
Use PTR_ERR() to propagate the actual error code returned by
devm_platform_ioremap_resource() instead of -ENOMEM.
Fixes: 75e0a1e301 ("clk: qcom: define probe by index API as common API")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251217041338.2432-1-vulab@iscas.ac.cn
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53a5c1d98d ]
As per datasheet of the HDMI protection IC the CEC_IC pin has been
configured as open-drain.
Fixes: ddabb3ce3f ("arm64: dts: freescale: add TQMa8MPQL on MBa8MP-RAS314")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8401527abb ]
As per datasheet of the HDMI protection IC the CEC_IC pin has been
configured as open-drain.
Fixes: 418d1d840e ("arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be4d4543f7 ]
The FF-A specification allows NOTIFICATION_INFO_GET to return either a
64-bit (FFA_FN64_SUCCESS) or a 32-bit (FFA_SUCCESS) response, depending on
whether the firmware chooses the SMC64 or SMC32 calling convention.
The driver previously detected the response format by checking ret.a0, but
still interpreted the returned ID lists (x3..x17 or w3..w7) as if they always
followed the 64-bit SMC64 layout. In the SMC32 case, the upper 32 bits of
each argument register are undefined by the calling convention, meaning the
driver could read stale or garbage values when parsing notification IDs.
This resulted in incorrectly decoded partition/VCPU IDs whenever the FF-A
firmware used an SMC32 return path.
Fix the issue by:
- Introducing logic to map list indices to the correct u16 offsets,
depending on whether the response width matches the kernel word size
or is a 32-bit response on a 64-bit kernel.
- Ensuring that the packed ID list is parsed using the proper layout,
avoiding reads from undefined upper halves in the SMC32 case.
With this change, NOTIFICATION_INFO_GET now correctly interprets ID list
entries regardless of the response width, aligning the driver with the FF-A
specification.
Fixes: 3522be48d8 ("firmware: arm_ffa: Implement the NOTIFICATION_INFO_GET interface")
Reported-by: Sourav Mohapatra <sourav.mohapatra@arm.com>
Message-Id: <20251218142001.2457111-1-sudeep.holla@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72f1268361 ]
The snprintf() can't really overflow because we're writing a max of 42
bytes to a PAGE_SIZE buffer. But my static checker complains because
the limit calculation doesn't take the first 11 space characters that
we wrote into the buffer into consideration. Fix this for the sake of
correctness even though it doesn't affect runtime.
Also delete an earlier "space -= n;" which was not used.
Fixes: 68d086f89b ("i5400_edac: improve debug messages to better represent the filled memory")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://patch.msgid.link/ccd06b91748e7ed8e33eeb2ff1e7b98700879304.1765290801.git.dan.carpenter@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b5c7e83ac ]
The snprintf() can't really overflow because we're writing a max of 42
bytes to a PAGE_SIZE buffer. But the limit calculation doesn't take
the first 11 bytes that we wrote into consideration so the limit is
not correct. Just fix it for correctness even though it doesn't
affect runtime.
Fixes: 64e1fdaf55 ("i5000_edac: Fix the logic that retrieves memory information")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://patch.msgid.link/07cd652c51e77aad5a8350e1a7cd9407e5bbe373.1765290801.git.dan.carpenter@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fe01a7955 ]
Fail the driver probe if the region can't be mapped
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez@oss.qualcomm.com>
Fixes: 20bb6c9de1 ("soc: qcom: smem: map only partitions used by local HOST")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251209074610.3751781-1-jorge.ramirez@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5669645c05 ]
persistent_ram_save_old() can be called multiple times for the same
persistent_ram_zone (e.g., via ramoops_pstore_read -> ramoops_get_next_prz
for PSTORE_TYPE_DMESG records).
Currently, the function only allocates prz->old_log when it is NULL,
but it unconditionally updates prz->old_log_size to the current buffer
size and then performs memcpy_fromio() using this new size. If the
buffer size has grown since the first allocation (which can happen
across different kernel boot cycles), this leads to:
1. A heap buffer overflow (OOB write) in the memcpy_fromio() calls
2. A subsequent OOB read when ramoops_pstore_read() accesses the buffer
using the incorrect (larger) old_log_size
The KASAN splat would look similar to:
BUG: KASAN: slab-out-of-bounds in ramoops_pstore_read+0x...
Read of size N at addr ... by task ...
The conditions are likely extremely hard to hit:
0. Crash with a ramoops write of less-than-record-max-size bytes.
1. Reboot: ramoops registers, pstore_get_records(0) reads old crash,
allocates old_log with size X
2. Crash handler registered, timer started (if pstore_update_ms >= 0)
3. Oops happens (non-fatal, system continues)
4. pstore_dump() writes oops via ramoops_pstore_write() size Y (>X)
5. pstore_new_entry = 1, pstore_timer_kick() called
6. System continues running (not a panic oops)
7. Timer fires after pstore_update_ms milliseconds
8. pstore_timefunc() → schedule_work() → pstore_dowork() → pstore_get_records(1)
9. ramoops_get_next_prz() → persistent_ram_save_old()
10. buffer_size() returns Y, but old_log is X bytes
11. Y > X: memcpy_fromio() overflows heap
Requirements:
- a prior crash record exists that did not fill the record size
(almost impossible since the crash handler writes as much as it
can possibly fit into the record, capped by max record size and
the kmsg buffer almost always exceeds the max record size)
- pstore_update_ms >= 0 (disabled by default)
- Non-fatal oops (system survives)
Free and reallocate the buffer when the new size differs from the
previously allocated size. This ensures old_log always has sufficient
space for the data being copied.
Fixes: 201e4aca5a ("pstore/ram: Should update old dmesg buffer before reading")
Signed-off-by: Sai Ritvik Tanksalkar <stanksal@purdue.edu>
Link: https://patch.msgid.link/20260201132240.2948732-1-stanksal@purdue.edu
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc2f39d6ac ]
Currently, hwrng_fill is not cleared until the hwrng_fillfn() thread
exits. Since hwrng_unregister() reads hwrng_fill outside the rng_mutex
lock, a concurrent hwrng_unregister() may call kthread_stop() again on
the same task.
Additionally, if hwrng_unregister() is called immediately after
hwrng_register(), the stopped thread may have never been executed. Thus,
hwrng_fill remains dirty even after hwrng_unregister() returns. In this
case, subsequent calls to hwrng_register() will fail to start new
threads, and hwrng_unregister() will call kthread_stop() on the same
freed task. In both cases, a use-after-free occurs:
refcount_t: addition on 0; use-after-free.
WARNING: ... at lib/refcount.c:25 refcount_warn_saturate+0xec/0x1c0
Call Trace:
kthread_stop+0x181/0x360
hwrng_unregister+0x288/0x380
virtrng_remove+0xe3/0x200
This patch fixes the race by protecting the global hwrng_fill pointer
inside the rng_mutex lock, so that hwrng_fillfn() thread is stopped only
once, and calls to kthread_run() and kthread_stop() are serialized
with the lock held.
To avoid deadlock in hwrng_fillfn() while being stopped with the lock
held, we convert current_rng to RCU, so that get_current_rng() can read
current_rng without holding the lock. To remove the lock from put_rng(),
we also delay the actual cleanup into a work_struct.
Since get_current_rng() no longer returns ERR_PTR values, the IS_ERR()
checks are removed from its callers.
With hwrng_fill protected by the rng_mutex lock, hwrng_fillfn() can no
longer clear hwrng_fill itself. Therefore, if hwrng_fillfn() returns
directly after current_rng is dropped, kthread_stop() would be called on
a freed task_struct later. To fix this, hwrng_fillfn() calls schedule()
now to keep the task alive until being stopped. The kthread_stop() call
is also moved from hwrng_unregister() to drop_current_rng(), ensuring
kthread_stop() is called on all possible paths where current_rng becomes
NULL, so that the thread would not wait forever.
Fixes: be4000bc46 ("hwrng: create filler thread")
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Lianjie Wang <karin0.zst@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e74b96d77d ]
The HW RNG core allows for manual selection of which RNG device to use,
but does not allow for no device to be enabled. It may be desirable to
do this on systems with only a single suitable hardware RNG, where we
need exclusive access to other functionality on this device. In
particular when performing TPM firmware upgrades this lets us ensure the
kernel does not try to access the device.
Before:
root@debian-qemu-efi:~# grep "" /sys/devices/virtual/misc/hw_random/rng_*
/sys/devices/virtual/misc/hw_random/rng_available:tpm-rng-0
/sys/devices/virtual/misc/hw_random/rng_current:tpm-rng-0
/sys/devices/virtual/misc/hw_random/rng_quality:1024
/sys/devices/virtual/misc/hw_random/rng_selected:0
After:
root@debian-qemu-efi:~# grep "" /sys/devices/virtual/misc/hw_random/rng_*
/sys/devices/virtual/misc/hw_random/rng_available:tpm-rng-0 none
/sys/devices/virtual/misc/hw_random/rng_current:tpm-rng-0
/sys/devices/virtual/misc/hw_random/rng_quality:1024
/sys/devices/virtual/misc/hw_random/rng_selected:0
root@debian-qemu-efi:~# echo none > /sys/devices/virtual/misc/hw_random/rng_current
root@debian-qemu-efi:~# grep "" /sys/devices/virtual/misc/hw_random/rng_*
/sys/devices/virtual/misc/hw_random/rng_available:tpm-rng-0 none
/sys/devices/virtual/misc/hw_random/rng_current:none
grep: /sys/devices/virtual/misc/hw_random/rng_quality: No such device
/sys/devices/virtual/misc/hw_random/rng_selected:1
(Observe using bpftrace no calls to TPM being made)
root@debian-qemu-efi:~# echo "" > /sys/devices/virtual/misc/hw_random/rng_current
root@debian-qemu-efi:~# grep "" /sys/devices/virtual/misc/hw_random/rng_*
/sys/devices/virtual/misc/hw_random/rng_available:tpm-rng-0 none
/sys/devices/virtual/misc/hw_random/rng_current:tpm-rng-0
/sys/devices/virtual/misc/hw_random/rng_quality:1024
/sys/devices/virtual/misc/hw_random/rng_selected:0
(Observe using bpftrace that calls to the TPM resume)
Signed-off-by: Jonathan McDowell <noodles@meta.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: cc2f39d6ac ("hwrng: core - use RCU and work_struct to fix race condition")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccb679fdae ]
The starfive_aes_aead_do_one_req() function allocates rctx->adata with
kzalloc() but fails to free it if sg_copy_to_buffer() or
starfive_aes_hw_init() fails, which lead to memory leaks.
Since rctx->adata is unconditionally freed after the write_adata
operations, ensure consistent cleanup by freeing the allocation in these
earlier error paths as well.
Compile tested only. Issue found using a prototype static analysis tool
and code review.
Fixes: 7467147ef9 ("crypto: starfive - Use dma for aes requests")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46a03ea50b ]
Remove duplicate entries from the bprm_stack_limits KUnit test vector
table. The duplicates do not add coverage and only increase test size.
Signed-off-by: Titouan Ameline de Cadeville <titouan.ameline@gmail.com>
Fixes: 60371f43e5 ("exec: Add KUnit test for bprm_stack_limits()")
Link: https://patch.msgid.link/20260203175950.43710-1-titouan.ameline@gmail.com
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94894c9c47 ]
CPU0 becomes overloaded when hosting a CPU-bound RT task, a non-CPU-bound
RT task, and a CFS task stuck in kernel space. When other CPUs switch from
RT to non-RT tasks, RT load balancing (LB) is triggered; with
HAVE_RT_PUSH_IPI enabled, they send IPIs to CPU0 to drive the execution
of rto_push_irq_work_func. During push_rt_task on CPU0,
if next_task->prio < rq->donor->prio, resched_curr() sets NEED_RESCHED
and after the push operation completes, CPU0 calls rto_next_cpu().
Since only CPU0 is overloaded in this scenario, rto_next_cpu() should
ideally return -1 (no further IPI needed).
However, multiple CPUs invoking tell_cpu_to_push() during LB increments
rd->rto_loop_next. Even when rd->rto_cpu is set to -1, the mismatch between
rd->rto_loop and rd->rto_loop_next forces rto_next_cpu() to restart its
search from -1. With CPU0 remaining overloaded (satisfying rt_nr_migratory
&& rt_nr_total > 1), it gets reselected, causing CPU0 to queue irq_work to
itself and send self-IPIs repeatedly. As long as CPU0 stays overloaded and
other CPUs run pull_rt_tasks(), it falls into an infinite self-IPI loop,
which triggers a CPU hardlockup due to continuous self-interrupts.
The trigging scenario is as follows:
cpu0 cpu1 cpu2
pull_rt_task
tell_cpu_to_push
<------------irq_work_queue_on
rto_push_irq_work_func
push_rt_task
resched_curr(rq) pull_rt_task
rto_next_cpu tell_cpu_to_push
<-------------------------- atomic_inc(rto_loop_next)
rd->rto_loop != next
rto_next_cpu
irq_work_queue_on
rto_push_irq_work_func
Fix redundant self-IPI by filtering the initiating CPU in rto_next_cpu().
This solution has been verified to effectively eliminate spurious self-IPIs
and prevent CPU hardlockup scenarios.
Fixes: 4bdced5c9a ("sched/rt: Simplify the IPI based RT balancing logic")
Suggested-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Suggested-by: K Prateek Nayak <kprateek.nayak@amd.com>
Signed-off-by: Chen Jinghuang <chenjinghuang2@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
Link: https://patch.msgid.link/20260122012533.673768-1-chenjinghuang2@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cb3b27693 ]
The defer params were not cleared in __dl_clear_params. Clear them.
Without this is some of my test cases are flaking and the DL timer is
not starting correctly AFAICS.
Fixes: a110a81c52 ("sched/deadline: Deferrable dl server")
Signed-off-by: Joel Fernandes <joelagnelf@nvidia.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Andrea Righi <arighi@nvidia.com>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Tested-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/20260126100050.3854740-2-arighi@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef92b98f5f ]
The interrupt handler iio_trigger_generic_data_rdy_poll() will invoke other
interrupt handlers and this supposed to happen from hard interrupt context.
Use IRQF_NO_THREAD to forbid forced-threading.
Fixes: 0ab13674a9 ("media: pci: mgb4: Added Digiteq Automotive MGB4 driver")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-21-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 553b4999cb ]
Using a threaded interrupt without a dedicated primary handler mandates
the IRQF_ONESHOT flag to mask the interrupt source while the threaded
handler is active. Otherwise the interrupt can fire again before the
threaded handler had a chance to run.
Mark explained that this should not happen with this hardware since it
is a slow irqchip which is behind an I2C/ SPI bus but the IRQ-core will
refuse to accept such a handler.
Set IRQF_ONESHOT so the interrupt source is masked until the secondary
handler is done.
Fixes: 1c6c69525b ("genirq: Reject bogus threaded irq requests")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260128095540.863589-16-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c858d6c66 ]
Passing IRQF_ONESHOT ensures that the interrupt source is masked until
the secondary (threaded) handler is done. If only a primary handler is
used then the flag makes no sense because the interrupt can not fire
(again) while its handler is running.
The flag also prevents force-threading of the primary handler and the
irq-core will warn about this.
Remove IRQF_ONESHOT from irqflags.
Fixes: a29d64a45e ("EDAC, altera: Add IRQ Flags to disable IRQ while handling")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-11-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd81f07e9a ]
There is no added value in efct_intr_msix() compared to
irq_default_primary_handler().
Using a threaded interrupt without a dedicated primary handler mandates
the IRQF_ONESHOT flag to mask the interrupt source while the threaded
handler is active. Otherwise the interrupt can fire again before the
threaded handler had a chance to run.
Use the default primary interrupt handler by specifying NULL and set
IRQF_ONESHOT so the interrupt source is masked until the secondary
handler is done.
Fixes: 4df84e8466 ("scsi: elx: efct: Driver initialization routines")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-8-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28abed6569 ]
There is no added value in btintel_pcie_msix_isr() compared to
irq_default_primary_handler().
Using a threaded interrupt without a dedicated primary handler mandates
the IRQF_ONESHOT flag to mask the interrupt source while the threaded
handler is active. Otherwise the interrupt can fire again before the
threaded handler had a chance to run.
Use the default primary interrupt handler by specifying NULL and set
IRQF_ONESHOT so the interrupt source is masked until the secondary
handler is done.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-7-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6bc712877 ]
Passing IRQF_ONESHOT ensures that the interrupt source is masked until the
secondary (threaded) handler is done. If only a primary handler is used
then the flag makes no sense because the interrupt cannot fire (again)
while its handler is running.
The flag also prevents force-threading of the primary handler and the
irq-core will warn about this.
The flag was added to match the flag on the shared handler which uses a
threaded handler and therefore IRQF_ONESHOT. This is no longer needed
because devm_request_irq() now passes IRQF_COND_ONESHOT for this case.
Revert adding IRQF_ONESHOT to irqflags.
Fixes: 8f812373d1 ("platform/x86: intel: int0002_vgpio: Pass IRQF_ONESHOT to request_irq()")
Reported-by: Borah, Chaitanya Kumar <chaitanya.kumar.borah@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260128095540.863589-3-bigeasy@linutronix.de
Closes: https://lore.kernel.org/all/555f1c56-0f74-41bf-8bd2-6217e0aab0c6@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 943b052ded ]
The flag IRQF_COND_ONESHOT was already force-added to request_irq() because
the ACPI SCI interrupt handler is using the IRQF_ONESHOT flag which breaks
all shared handlers.
devm_request_irq() needs the same change since some users, such as
int0002_vgpio, are using this function instead.
Add IRQF_COND_ONESHOT to the flags passed to devm_request_irq().
Fixes: c37927a203 ("genirq: Set IRQF_COND_ONESHOT in request_irq()")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-2-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6557f1565d ]
While making some maps in Cilium read-only from the BPF side, we noticed
that the bpf_xdp_store_bytes proto is incorrect. In particular, the
verifier was throwing the following error:
; ret = ctx_store_bytes(ctx, l3_off + offsetof(struct iphdr, saddr),
&nat->address, 4, 0);
635: (79) r1 = *(u64 *)(r10 -144) ; R1=ctx() R10=fp0 fp-144=ctx()
636: (b4) w2 = 26 ; R2=26
637: (b4) w4 = 4 ; R4=4
638: (b4) w5 = 0 ; R5=0
639: (85) call bpf_xdp_store_bytes#190
write into map forbidden, value_size=6 off=0 size=4
nat comes from a BPF_F_RDONLY_PROG map, so R3 is a PTR_TO_MAP_VALUE.
The verifier checks the helper's memory access to R3 in
check_mem_size_reg, as it reaches ARG_CONST_SIZE argument. The third
argument has expected type ARG_PTR_TO_UNINIT_MEM, which includes the
MEM_WRITE flag. The verifier thus checks for a BPF_WRITE access on R3.
Given R3 points to a read-only map, the check fails.
Conversely, ARG_PTR_TO_UNINIT_MEM can also lead to the helper reading
from uninitialized memory.
This patch simply fixes the expected argument type to match that of
bpf_skb_store_bytes.
Fixes: 3f364222d0 ("net: xdp: introduce bpf_xdp_pointer utility routine")
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Link: https://lore.kernel.org/r/9fa3c9f72d806e82541071c4df88b8cba28ad6a9.1769875479.git.paul.chaignon@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
