The hardware performs packet parsing before packet transmission.
Parsing incomplete IPv4, IPv6, TCP, or UDP headers may trigger a TX
hang because the hardware parser expects additional protocol header
data that is not present in the packet.
The hardware performs additional PTP parsing on UDP packets identified
by destination ports 319/320 at the expected UDP destination port
offset.
If such a packet has transport data smaller than RTASE_MIN_PAD_LEN,
the hardware parser expects additional packet data and may trigger a
TX hang.
To avoid these hardware issues, the driver applies the following
workarounds.
Drop malformed packets that may trigger this hardware issue before
transmission.
For IPv4 non-initial fragments, the hardware does not check the
fragment offset before parsing the expected transport header location.
As a result, these packets are still subject to transport header
parsing even though they do not contain a transport header. If the
transport data is shorter than the minimum transport header required
by the hardware parser, pad the transport data to the minimum
transport header length required by the hardware parser. Packets that
also match the hardware PTP parsing conditions continue to follow the
corresponding workaround.
For IPv6 fragmented packets, neither of the above hardware issues
occurs because the hardware only continues packet parsing when the
IPv6 Base Header Next Header field directly indicates UDP. Packets
carrying a Fragment Header do not continue through the subsequent
packet parsing stages.
For packets identified for hardware PTP parsing, pad the transport
data so it reaches RTASE_MIN_PAD_LEN before transmission.
Fixes: d6e882b89f ("rtase: Implement .ndo_start_xmit function")
Cc: stable@vger.kernel.org
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260709103456.83789-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mptcp_get_options() clears only the status group of struct
mptcp_options_received; data_seq, subflow_seq and data_len are filled in
by mptcp_parse_option() exclusively inside the DSS mapping block, which
runs only when the DSS M (mapping present) bit is set.
A peer can send a DSS option with the DATA_FIN flag set but the mapping
bit clear. The parser then records mp_opt->data_fin while leaving
data_len and data_seq uninitialized. For a zero-length segment
mptcp_incoming_options() evaluates
if (mp_opt.data_fin && mp_opt.data_len == 1 &&
mptcp_update_rcv_data_fin(msk, mp_opt.data_seq, mp_opt.dsn64))
which reads the uninitialized data_len and data_seq; KMSAN reports an
uninit-value in mptcp_incoming_options(). The stale data_seq can also be
fed into the receive-side DATA_FIN sequence tracking.
Record the DATA_FIN flag only when the DSS option carries a mapping, so
data_fin is never set without data_seq and data_len also being present.
data_fin is part of the status group that mptcp_get_options() clears up
front, so on the no-map path it stays zero and the zero-length DATA_FIN
branch is simply skipped. A DATA_FIN is always transmitted together with
a mapping (mptcp_write_data_fin() sets use_map along with data_seq and
data_len), so legitimate DATA_FIN handling is unaffected.
Move the pr_debug() that logs the parsed DSS flags below the mapping
block, so it reports the final data_fin value instead of the stale one
it would otherwise print before the assignment.
Fixes: 43b54c6ee3 ("mptcp: Use full MPTCP-level disconnect state machine")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260709191925.2811195-1-michael.bommarito@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure the IPv4/6 and UDP headers are writable before fixing them up in
geneve_post_decap_hint. As skb_ensure_writable can reallocate the skb linear
area, reload the GRO hint header pointer and only set the IPv4/6 header ones
after the call.
Fixes: fd0dd79657 ("geneve: use GRO hint option in the RX path")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/patchset/20260529144713.780938-1-atenart%40kernel.org
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260709125000.141092-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The BCM43752 is not reliable with the default 512-byte SDIO function 2
block size: on an i.MX8MP board with an AMPAK AP6275S module at
SDR104 / 200 MHz, an iperf TX stress test kills WLAN within seconds:
mmc_submit_one: CMD53 sg block write failed -84
brcmf_sdio_dpc: failed backplane access over SDIO, halting operation
Commit d2587c57ff ("brcmfmac: add 43752 SDIO ids and initialization")
set up the 43752 like the 4373 for the F2 watermark but missed the F2
block size, which the 4373 limits to 256 bytes. The vendor driver
(bcmdhd) also programs a 256-byte F2 block size for this chip and runs
the same hardware without errors.
Group the 43752 with the 4373, matching the F2 watermark handling.
With this change a 10-minute bidirectional iperf3 soak completes with
zero SDIO errors at ~270 Mbit/s in each direction.
Backporting note: kernels before v6.18 name this id
SDIO_DEVICE_ID_BROADCOM_CYPRESS_43752, so on those trees the case
label added by this patch must be adjusted to that name. Cherry-picking
the rename commit 74e2ef72bd ("wifi: brcmfmac: fix 43752 SDIO FWVID
incorrectly labelled as Cypress (CYW)") first is not a clean
alternative: on trees before v6.17 its context collides with the 43751
additions, and trees before v6.2 lack the FWVID framework it touches.
Fixes: d2587c57ff ("brcmfmac: add 43752 SDIO ids and initialization")
Cc: stable@vger.kernel.org # see patch description, needs adjustments for <= 6.17
Signed-off-by: LiangCheng Wang <zaq14760@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260715-b43752-f2-blksz-v2-1-f9be49856050@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sk_clone() fails, sk_destruct() is called for the new socket.
If the parent socket has SK_FLAGS_TIMESTAMP in sk->sk_flags,
net_disable_timestamp() is called for the child socket even though
net_enable_timestamp() is not called for it.
Let's call net_enable_timestamp() before any failure path in
sk_clone().
Fixes: 704da560c0 ("tcp: update the netstamp_needed counter when cloning sockets")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/all/20260709032007.9E4D61F000E9@smtp.kernel.org/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260709183315.965751-3-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When sk_clone() fails, sk_destruct() is called for the new socket.
If the parent socket has sk->sk_reuseport_cb, the child will call
reuseport_detach_sock() for the reuseport group.
Let's clear sk->sk_reuseport_cb before any failure path in sk_clone().
Note that this was not a problem before the cited commit because
reuseport_detach_sock() did nothing if the socket was not found in
the reuseport array.
Fixes: 5dc4c4b7d4 ("bpf: Introduce BPF_MAP_TYPE_REUSEPORT_SOCKARRAY")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/all/20260709032007.9E4D61F000E9@smtp.kernel.org/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260709183315.965751-2-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MAC_AUTO_SW (VR_MII_DIG_CTRL1 bit 9) enables automatic XPCS speed
mode switching after CL37 auto-negotiation and is only meaningful in
SGMII MAC mode. The original code unconditionally set this bit on
every call to xgbe_an37_set(), including when called from
xgbe_an37_disable() with enable=false. This left MAC_AUTO_SW=1 after
AN was disabled, causing the XPCS to autonomously switch speed from
stale AN state during subsequent mode changes, breaking SGMII speed
negotiation on 1G copper SFP modules.
Patrick: This was breaking negotiation for all 1G SFP modules,
not just copper modules.
Fixes: 42fd432fe6 ("amd-xgbe: align CL37 AN sequence as per databook")
Reported-by: Patrick Oppenlander <patrick.oppenlander@gmail.com>
Link: https://lore.kernel.org/netdev/CAEg67GmFS0Q4oSZkz8zWdOzckSth9_vBPiOy6a7-d697C2w2Xg@mail.gmail.com
Signed-off-by: Prashanth Kumar KR <PrashanthKumar.K.R@amd.com>
Tested-by: Patrick Oppenlander <patrick.oppenlander@gmail.com>
Link: https://patch.msgid.link/20260709095006.3683940-1-prashanthkumar.k.r@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This field comes from userspace and should be validated against specific
limits depending on which Shader Model (SM) is available.
Fixes: 504901dbb0 ("drm/vmwgfx: Refactor surface_define to use vmw_surface_metadata")
Reported-by: Zero Day Initiative <zdi-disclosures@trendmicro.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ian Forbes <ian.forbes@broadcom.com>
Reviewed-by: Maaz Mombasawala <maaz.mombasawala@broadcom.com>
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://patch.msgid.link/20260623193314.506257-1-ian.forbes@broadcom.com
Commit 0ab03f353d ("net-gro: Fix GRO flush when receiving a GSO
packet.") added a flush check to skb_gro_receive(), but
skb_gro_receive_list() lacks the same validation.
As a result, packets marked with NAPI_GRO_CB(skb)->flush may still be
re-aggregated.
This allows already-GRO'd packets with existing frag_list to be
re-aggregated into a new GRO session, corrupting the frag_list chain
structure. When skb_segment() attempts to unpack these malformed packets,
it encounters invalid state and triggers a kernel panic.
Scenario (Tethering/Device forwarding):
1. Driver: Generated aggregated packet P1 via LRO with frag_list
2. Dev A: Receives aggregated fraglist packet and flush flag set
3. Dev A: Re-enters GRO, skb_gro_receive_list() is called
4. Missing flush check allows re-aggregation despite flush flag
5. Frag_list chain becomes corrupted (loops or dangling refs)
6. Dev B: TX path calls skb_segment(), crashes on corrupted frag_list
Root cause in skb_segment():
The check at line ~4891:
if (hsize <= 0 && i >= nfrags && skb_headlen(list_skb) &&
(skb_headlen(list_skb) == len || sg)) {
When frag_list is corrupted by double aggregation, when list_skb is
a NULL pointer from skb->next, skb_headlen(list_skb) dereference
NULL/corrupted pointers occurs.
Call Trace:
skb_headlen(NULL skb)
skb_segment
tcp_gso_segment
tcp4_gso_segment
inet_gso_segment
skb_mac_gso_segment
__skb_gso_segment
skb_gso_segment
validate_xmit_skb
validate_xmit_skb_list
sch_direct_xmit
qdisc_restart
__qdisc_run
qdisc_run
net_tx_action
Fix: Add NAPI_GRO_CB(skb)->flush validation to the early-return check in
skb_gro_receive_list(), matching the defensive programming pattern of
skb_gro_receive().
Fixes: 3a1296a38d ("net: Support GRO/GSO fraglist chaining.")
Cc: stable@vger.kernel.org
Signed-off-by: Shiming Cheng <shiming.cheng@mediatek.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260709014704.3625-1-shiming.cheng@mediatek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Avoid redundant allocations when allocating IMSIC page tables
- Apply SBI FWFT LOCK flag only on successful set
- Bound SBI PMU counter mask scan to BITS_PER_LONG, since on RV32
the PMU SBI start/stop helper can only access 32 PMU counters.
- Skip TLB flush when G-stage PTE becomes valid if the Svvptc
extension is available.
- Always show Zicbo[m|z|p] block sizes in ONE_REG
- Inject instruction access fault on unmapped guest fetch
- Use raw spinlock for irqs_pending and irqs_pending_mask
- Fix Spectre-v1 in vector register access via ONE_REG
x86:
- Fixes to SEV selftests.
- Once free_nested() did a VMCLEAR of shadow VMCS, there's no need to VMCLEAR it
again if the kernel is preempted and thread migration happens
- Preserve nested TDP shadow page tables if they are used as roots, instead of
clearing them unnecessarily
- Fix use of stale data if out-of-memory happens after vendor module reload
- Check for invalid/obsolete root *after* making MMU pages available, because
the latter can make a page invalid
- Only reset TSC Deadline Timer in apic_timer_expired on KVM_RUN
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmpfSUwUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOrWQf/S8Za6t7bZbQbJHDV0NXCKufpyKyz
l6WMsLGdn4LFLNqCtKhvQf5lEZ5PKRHFTGoWrO1wQSbREHRUCnfMD5lsSKQA4Grf
0QpQ6YBjXFv6zg0M456/Q/S1oyusyqkXXBS8BxlBQyfqR+ByKx8f4PXTGazfUua3
4SPHr5TUxr6CXy8715OQUGa1Xdf0/5d3OseiAgBwqM31yZPhK0tsar77Cd9P93bs
DC+FzfphHg0gb3s/xSfuVR0BPnqHvQMDF9rS/YKgJgJdZkzHXCo7muWRQmHWK+FR
Q2zOTWSlJATQucC0+2j1yj2Wdhg1itgZTfj/8RaIDRKbmjk0S1bLc3bamg==
=Svds
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"RISC-V:
- Avoid redundant allocations when allocating IMSIC page tables
- Apply SBI FWFT LOCK flag only on successful set
- Bound SBI PMU counter mask scan to BITS_PER_LONG, since on RV32 the
PMU SBI start/stop helper can only access 32 PMU counters.
- Skip TLB flush when G-stage PTE becomes valid if the Svvptc
extension is available.
- Always show Zicbo[m|z|p] block sizes in ONE_REG
- Inject instruction access fault on unmapped guest fetch
- Use raw spinlock for irqs_pending and irqs_pending_mask
- Fix Spectre-v1 in vector register access via ONE_REG
x86:
- Fixes to SEV selftests
- Once free_nested() did a VMCLEAR of shadow VMCS, there's no need to
VMCLEAR it again if the kernel is preempted and thread migration
happens
- Preserve nested TDP shadow page tables if they are used as roots,
instead of clearing them unnecessarily
- Fix use of stale data if out-of-memory happens after vendor module
reload
- Check for invalid/obsolete root *after* making MMU pages available,
because the latter can make a page invalid
- Only reset TSC Deadline Timer in apic_timer_expired on KVM_RUN"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Only reset TSC Deadline Timer in apic_timer_expired on KVM_RUN
KVM: selftests: sev_init2_tests: Derive SEV availability from KVM
KVM: selftests: sev_smoke_test: Only run VM types the host offers
KVM: x86/mmu: Fix use-after-free on vendor module reload
KVM: x86/mmu: Preserve nested TDP shadow page tables if they are used as roots
KVM: x86: Check for invalid/obsolete root *after* making MMU pages available
KVM: nVMX: Hide shadow VMCS right after VMCLEAR
KVM: riscv: Fix Spectre-v1 in vector register access
RISC-V: KVM: Serialize virtual interrupt pending state updates
RISC-V: KVM: Inject instruction access fault on unmapped guest fetch
RISC-V: KVM: Zicbo[m|z|p] block sizes should be always present in ONE_REG
riscv: kvm: Skip TLB flush when G-stage PTE becomes valid with Svvptc
KVM: riscv: PMU: Bound counter mask scan to BITS_PER_LONG
KVM: riscv: SBI FWFT: Apply LOCK flag only on successful set
RISC-V: KVM: Avoid redundant page-table allocations in ioremap topup
prevent_memory_remove_notifier() advances pfn while scanning the requested
range for early memory. When the loop completes, pfn is at or beyond
end_pfn. Passing it to can_unmap_without_split() therefore checks a range
after the one being offlined.
Consequently, a valid request can be rejected based on the following
range, while a request that would split a leaf mapping can be accepted if
the shifted range can be unmapped without a split. This was observed with
CXL DAX memory, where the final memory block was incorrectly allowed to
be offlined.
Pass arg->start_pfn into can_unmap_without_split() so it checks the
requested range.
Fixes: 95a58852b0 ("arm64/mm: Reject memory removal that splits a kernel leaf mapping")
Signed-off-by: Richard Cheng <icheng@nvidia.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
- tracing/probes: Avoid temporary buffer truncation in match_command_args()
Compare argument name, delimiter, and comm expression directly instead of
formatting into a stack buffer to prevent false matching failures.
- tracing/probes: Prevent out-of-bounds write in __trace_probe_log_err()
Return early when trace_probe_log.argc is zero to prevent out-of-bounds
access when constructing the formatted error command string.
- tracing/probes: Fix potential underflow in LEN_OR_ZERO macro
Ensure buffer length is greater than current position before subtraction
to prevent unsigned size underflow when formatting print strings.
- tracing/eprobe: Fix exact system name matching in eprobe_dyn_event_match()
Check system name null-termination to avoid partial prefix matching when
comparing event probe target system names.
-----BEGIN PGP SIGNATURE-----
iQFPBAABCgA5FiEEh7BulGwFlgAOi5DV2/sHvwUrPxsFAmpfMPgbHG1hc2FtaS5o
aXJhbWF0c3VAZ21haWwuY29tAAoJENv7B78FKz8bDm8IAJ3GuBwQOTcVyn1+7Poh
fOtXOD9yMIV2YYoe6MDD/ZF1JCCnJgzgjPOqRbZjM4uGE8QbEuGnrwwu3zRiNON3
JU1R5aOxadflNhOnY7HxPjDHTwxJ5z+Ju10wPM+YE3M9gLKia8uzCabdEgYEly01
Rx6kpGKdsNgtJ/uAbrZlx++YtJCmBI1j+SdnRgNSejbcJUBtTmt+VYA+oh7ISF0f
Fuhw6MuznpnA9JkLrPJaUI6KLiNLEoLQVS2gqhCD0PvrlDGF/h+b7Qbv9ML0C8YW
W0p38Sq0Pc9lNlukYJlkh1A4H7lbAGpdGgZVoCvMQZt1ccy+H1QYfXzrFRlYyRWk
n6g=
=pC9O
-----END PGP SIGNATURE-----
Merge tag 'probes-fixes-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull probes fixes from Masami Hiramatsu:
- Avoid temporary buffer truncation in match_command_args()
Compare argument name, delimiter, and comm expression directly
instead of formatting into a stack buffer to prevent false
matching failures
- Prevent out-of-bounds write in __trace_probe_log_err()
Return early when trace_probe_log.argc is zero to prevent
out-of-bounds access when constructing the formatted error
command string
- Fix potential underflow in LEN_OR_ZERO macro
Ensure buffer length is greater than current position before
subtraction to prevent unsigned size underflow when formatting
print strings
- Fix exact system name matching in eprobe_dyn_event_match()
Check system name null-termination to avoid partial prefix
matching when comparing event probe target system names
* tag 'probes-fixes-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/eprobe: Fix exact system name matching in eprobe_dyn_event_match()
tracing/probes: Fix potential underflow in LEN_OR_ZERO macro
tracing/probes: Prevent out-of-bounds write in __trace_probe_log_err()
tracing/probes: Avoid temporary buffer truncation in trace_probe_match_command_args()
Address size fault, level -1 is encoded as 0b101001 or 0x29 according to
the Arm ARM. Correct the value to match the spec. This also matches the
offset of "level -1 address size fault" in the fault_info array in
fault.c.
Fixes: fb8a3eba9c ("KVM: arm64: Only read HPFAR_EL2 when value is architecturally valid")
Signed-off-by: Steven Price <steven.price@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
-----BEGIN PGP SIGNATURE-----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=1jNx
-----END PGP SIGNATURE-----
Merge tag 'for-7.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"I'm catching up with the fix backlog in the development branch, so
here's a number of them and will probably send one more for this or
the next rc:
- relocation fixes:
- skip attempting compression on reloc inodes
- exclude inline extents from file extent offset checks
- fix minor memory leak after error when adding reloc root
- fix root cleanup after inserting and merging
- fix clearing folio tags after writeback
- clear logging flag of extent map before splitting
- fix unsigned 32/64 type conversions when accounting dirty metadata,
leading to continually exceeding threshold
- fix regression in 32bit compat ioctl for subvolume info
- fix type of SEARCH_TREE ioctl buffer in UAPI header
- fix expression in ASSERT expression which can be unconditionally
evaluated on some compilers
- only account delalloc bytes for regular inodes"
* tag 'for-7.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix GET_SUBVOL_INFO after compat refactor
btrfs: free mapping node on duplicate reloc root insert
btrfs: fix a regression where PAGECACHE_TAG_DIRTY is never cleared
btrfs: don't propagate EXTENT_FLAG_LOGGING to split extent maps
btrfs: fix u32 to s64 type conversion in dirty_metadata_bytes accounting
btrfs: fix NULL pointer deref during assertion in btrfs_backref_free_node()
btrfs: only account delalloc bytes for regular file inodes in btrfs_getattr()
btrfs: reject inline file extents item in get_new_location()
btrfs: do not try compression for data reloc inodes
btrfs: declare btrfs_ioctl_search_args_v2::buf as __u8
btrfs: fix reloc root cleanup in merge_reloc_roots()
btrfs: fix use-after-free on reloc root after error in insert_dirty_subvol()
The MSI Crosshair A16 HX D7WFKG has an internal digital microphone
connected through AMD ACP6x, but the system does not expose the
AcpDmicConnected ACPI property. As a result, acp_yc_mach does not bind
and no DMIC capture device is created.
Add a DMI quirk for this model. This was tested on a system with board
MS-15PL, BIOS E15PLAMS.10B, and AMD ACP6x rev 0x62. After applying the
quirk, the internal microphone appears as an acp6x DMIC capture device
and records correctly.
Signed-off-by: 郑鸿源 <spark_psc@outlook.com>
Reviewed-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://patch.msgid.link/20260721-master-v1-1-6f56d5a54d96@outlook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A bug was reported when rtla-timerlat-top tool performs on-threshold
actions, even though no threshold was hit. This is reproduced even if no
threshold is set at all:
$ rtla timerlat top -q -c 0 --on-threshold shell,command='echo BAD'
BAD
Timer Latency
...
The bug is due to incorrect logic in timerlat_top_bpf_main_loop().
The loop uses timerlat_bpf_wait(), the return values of which are:
- > 0 (number of ringbuffer entries): at least 1 CPU hit threshold
- = 0: time out
- < 0: wait was interrupted by a signal
Commit 3138df6f0c ("rtla/timerlat: Exit top main loop on any non-zero
wait_retval") changed the condition for "threshold hit" from
"wait_reval == 1" (exactly 1 CPU hit threshold) to "wait_retval != 0",
to fix a race where multiple CPUs hit the threshold at the same time.
That also made it incorrectly include a signal (< 0), coming from either
duration expired (SIGALRM) or user interrupt (SIGINT).
Check for wait_retval greater than zero in the if condition to cover all
return values correctly.
Fixes: 3138df6f0c ("rtla/timerlat: Exit top main loop on any non-zero wait_retval")
Reported-by: Attila Fazekas <afazekas@redhat.com>
Reviewed-by: Wander Lairson Costa <wander@redhat.com>
Link: https://lore.kernel.org/r/20260713141047.687877-1-tglozar@redhat.com
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
The legacy firmware update path does not support per-component updates.
If a user specifies a component parameter with devlink flash, reject
the request with -EOPNOTSUPP rather than silently ignoring the component
parameter and flashing the entire firmware image.
Fixes: 49ce92fbee ("pds_core: add FW update feature to devlink")
Signed-off-by: Nikhil P. Rao <nikhil.rao@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260708163649.128620-1-nikhil.rao@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
vc4_gem_object_mmap() rejects a writable mapping of a validated shader
BO, but leaves VM_MAYWRITE set. Userspace can map the BO read-only and
then turn it writable with mprotect().
Validated shader BOs must stay read-only: the validator checks the
instructions once and the GPU trusts them afterwards. A writable
mapping lets userspace rewrite the code after validation, bypassing the
validator.
Clear VM_MAYWRITE on the read-only path so the mapping cannot be
upgraded, as i915 already does for its read-only objects.
Fixes: 463873d570 ("drm/vc4: Add an API for creating GPU shaders in GEM BOs.")
Cc: stable@vger.kernel.org
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/dri-devel/20260720085554.B0AF01F000E9@smtp.kernel.org/
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Link: https://patch.msgid.link/20260721011558.1672477-1-lilinmao@kylinos.cn
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
pmsr_parse_ftm() rejects a request that omits NOMINAL_TIME only for
non-trigger-based PD ranging. It then reads the attribute
unconditionally for every non-trigger-based request:
out->ftm.nominal_time =
nla_get_u32(tb[NL80211_PMSR_FTM_REQ_ATTR_NOMINAL_TIME]);
For the other non-trigger-based request types NOMINAL_TIME is optional,
so tb[...] can be NULL and nla_get_u32() dereferences a NULL pointer.
Keep the requirement for PD ranging and read the nominal-time value only
when the attribute is present.
Fixes: 8823a9b0e7 ("wifi: cfg80211: add NTB continuous ranging and FTM request type support")
Cc: stable@vger.kernel.org
Assisted-by: Codex:gpt-5
Assisted-by: Claude:opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260708195911.84365-5-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This PR contains quite a few fixes, mostly found by LLMs. Notably:
- missing validation of TLVs length
- missing validation on the revision of BIOS tables
- missing validation of fw responses length
- protect against double free of RX pointers
- avoid double deregistration of the tzone core
- validate fields in FW responses before using them
- fix off-by-one in WLAN_EID_EXT_CAPABILITY parsing
- Add missing support for UNII-9
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQM3A3Pv7vbm9vtjWbacY7uyt+OfQUCal9OxwAKCRDacY7uyt+O
fWfkAQDb/MrxlM6sihTSHBQ+lrLPgp0JYTkSHYGI606/CFO4swD+PLcMPeDvUm1+
fIP1NybrXA3jVfmt4EEm6VVF1LL8bwI=
=wkfs
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-fixes-2026-07-21' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Miri Korenblit says:
====================
wifi: iwlwif: fixes - 2026-07-21
This PR contains quite a few fixes, mostly found by LLMs. Notably:
- missing validation of TLVs length
- missing validation on the revision of BIOS tables
- missing validation of fw responses length
- protect against double free of RX pointers
- avoid double deregistration of the tzone core
- validate fields in FW responses before using them
- fix off-by-one in WLAN_EID_EXT_CAPABILITY parsing
- Add missing support for UNII-9
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
hwsim_tx_info_frame_received_nl() casts the HWSIM_ATTR_TX_INFO payload
to a struct hwsim_tx_rate * and unconditionally reads
IEEE80211_TX_MAX_RATES entries (8 bytes) from it. The policy only bounds
the attribute from above (NLA_BINARY .len is a maximum) and the op sets
GENL_DONT_VALIDATE_STRICT, so a short or zero-length attribute is
accepted and the loop reads past the payload.
Require the exact length in the policy, so a malformed attribute is
rejected before the handler runs.
Signed-off-by: Ibrahim Hashimov <security@auditcode.ai>
Assisted-by: AuditCode-AI:2026.07
Link: https://patch.msgid.link/20260721115346.17236-1-security@auditcode.ai
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
brcmf_fw_crashed() and the debugfs "reset" entry both schedule
drvr->bus_reset, whose callback recovers drvr through container_of()
and dereferences it. The removal path frees drvr (brcmf_free ->
wiphy_free) without draining the work, so a bus_reset callback pending
or running during removal can outlive drvr.
Cancellation cannot live in brcmf_detach() or brcmf_free(): the work
callback reaches teardown through the bus .reset op (PCIe
brcmf_pcie_reset -> brcmf_detach; SDIO brcmf_sdio_bus_reset ->
brcmf_sdiod_remove -> brcmf_free), so cancelling there would wait for
the running work and deadlock.
Add a per-bus mutex (bus_reset_lock) and route all arming through
brcmf_bus_schedule_reset(), which under the lock skips when the bus is
marked removing. Each bus remove entry calls
brcmf_bus_cancel_reset_work(), which under the same lock sets removing
and cancels the work. Holding the mutex across cancel_work_sync() makes
the set-removing + drain step atomic. Every producer reaches the arming
path from process context -- the PCIe firmware-halt notification runs in
the threaded IRQ handler (brcmf_pcie_isr_thread) and the SDIO hostmail
path runs from the data workqueue -- so the mutex is taken only in
sleepable contexts. Where applicable the remove entry first stops the
firmware-crash producer: on PCIe mask the mailbox and synchronize_irq;
on SDIO unregister the bus interrupt and cancel the data worker, which
also reports firmware halts through brcmf_fw_crashed(). The mutex is
initialized at bus allocation. The SDIO suspend power-off path frees
drvr through the same brcmf_sdiod_remove() and takes the same lock;
resume re-allows the work only on a successful re-probe.
Also guard brcmf_fw_crashed() against a NULL bus_if/drvr: it can fire
before brcmf_attach() wires up drvr, and it dereferences drvr
(bphy_err/brcmf_dev_coredump) before reaching the arming gate.
The bus_reset work is shared across buses, so the drain is applied to
every remove path: PCIe (the .reset op introduced by the Fixes commit),
SDIO (arms the same work through brcmf_fw_crashed()), and USB (via the
debugfs "reset" entry). cancel_work_sync() drains a running or pending
bus_reset work item before removal frees drvr, and patch 1/2 makes the
scratch-buffer release safe when reset teardown has already released
those DMA buffers.
This patch fixes the lifetime of the bus_reset work item itself. It does
not attempt to address the separate, pre-existing lifetime of the
asynchronous firmware completion started by the PCIe reset path. That
callback needs its own lifetime/ownership protocol and is being tracked
separately.
This issue was found by an in-house static analysis tool.
Fixes: 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Assisted-by: Codex:gpt-5.6
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260718024353.3147201-3-fanwu01@zju.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
brcmf_pcie_release_scratchbuffers() frees the shared.scratch and
shared.ringupd DMA buffers with dma_free_coherent() but does not clear
the pointers afterwards, unlike the sibling release_ringbuffers() which
NULLs commonrings/flowrings/idxbuf on release.
Both the bus_reset .reset callback (brcmf_pcie_reset) and
brcmf_pcie_remove() call release_scratchbuffers. When reset teardown
has run before removal, remove's own teardown would call
dma_free_coherent() a second time on the already-freed DMA allocation.
NULL the pointers after free, matching release_ringbuffers(), so a later
release observes that the allocation has already been released. This
patch makes repeated sequential release safe; the reset-work lifetime is
handled separately by the following patch.
This issue was found by an in-house static analysis tool.
Fixes: 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Assisted-by: Codex:gpt-5.6
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260718024353.3147201-2-fanwu01@zju.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an AP buffers frames for a station on its per-station TXQs and the
station subsequently enters power save, sta_ps_start() records the
buffered TIDs in txq_buffered_tids but does not update the TIM. The
station's TIM bit is only ever set when a further frame is buffered
while the station is already asleep
(ieee80211_tx_h_unicast_ps_buf() -> sta_info_recalc_tim()).
If no further downlink frame arrives for that station the beacon
TIM never advertises the buffered traffic. A station relying on the
TIM then remains in doze indefinitely on top of a non-empty queue. Its
TXQs were removed from the scheduler's active list at PS entry, nothing
pages it, and the flow deadlocks until an unrelated event wakes the
station.
Recalculate the TIM at the end of sta_ps_start(), so traffic
already buffered at PS entry is advertised immediately.
sta_info_recalc_tim() already consults txq_buffered_tids, which is
updated above, and is safe in this context (it is already called
from equivalent paths such as the tx handlers and
ieee80211_handle_filtered_frame()).
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Andrew Pope <andrew.pope@morsemicro.com>
Link: https://patch.msgid.link/20260717011751.79524-1-andrew.pope@morsemicro.com
[add wifi: subject prefix]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
dmar_latency_disable() intends to zero out only the single
latency_statistic entry for the given type, but the memset size was
computed as sizeof(*lstat) * DMAR_LATENCY_NUM, which clears the entire
array starting from &lstat[type].
When type > 0, this writes beyond the end of the allocated array,
corrupting adjacent memory.
Fix by using sizeof(*lstat) to clear only the target entry.
Fixes: 55ee5e67a5 ("iommu/vt-d: Add common code for dmar latency performance monitors")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Will Deacon <will@kernel.org>
The ivrs_acpihid command-line parser appends entries to a fixed
four-element early_acpihid_map array. Unlike the sibling IOAPIC and HPET
parsers, it does not reject a fifth entry before incrementing the map size.
Check the capacity at the common found label before parsing the HID and
UID or writing the entry.
Fixes: ca3bf5d47c ("iommu/amd: Introduces ivrs_acpihid kernel parameter")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: Ankit Soni <Ankit.Soni@amd.com>
Signed-off-by: Will Deacon <will@kernel.org>
mwifiex_tdls_add_ht_oper() gates its follow-the-AP-bandwidth path on
bss_desc->bcn_ht_cap being present, but then dereferences a different
pointer, bss_desc->bcn_ht_oper:
if (ISSUPP_CHANWIDTH40(priv->adapter->hw_dot_11n_dev_cap) &&
bss_desc->bcn_ht_cap &&
ISALLOWED_CHANWIDTH40(bss_desc->bcn_ht_oper->ht_param))
bcn_ht_cap and bcn_ht_oper are populated independently while parsing the
associated AP's beacon in mwifiex_update_bss_desc_with_ie(): an AP that
advertises an HT Capabilities element but no HT Operation element leaves
bcn_ht_cap non-NULL and bcn_ht_oper NULL. Setting up a TDLS link to a
peer while associated to such an AP then dereferences the NULL
bcn_ht_oper and crashes the kernel. Every other bcn_ht_oper user in the
driver NULL-checks it first.
Guard on the pointer that is actually dereferenced.
Found by 0sec automated security-research tooling (https://0sec.ai).
Fixes: 396939f940 ("mwifiex: add HT operation IE in TDLS setup confirm")
Cc: stable@vger.kernel.org
Assisted-by: 0sec:multi-model
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20260716103042.88469-1-doruk@0sec.ai
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace deprecated one-element arrays with flexible array members.
CONFIG_FORTIFY_SOURCE reports the following warning when
one-element arrays are used as variable-length buffers:
sta_cmd.c:1033 mwifiex_sta_prepare_cmd
memcpy: detected field-spanning write (size 84) of single field
"domain->triplet" at .../marvell/mwifiex/sta_cmd.c:1033 (size 3)
Convert affected structs to use flexible array members.
- Preserve existing wire layouts.
- Use DECLARE_FLEX_ARRAY() for structs inside affected unions.
Tested-on: WRT3200ACM, OpenWrt
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20260716001728.57799-1-gvalkov@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
at76_guess_freq() checks only that the received frame is at least a bare
802.11 header (24 bytes) before subtracting the fixed management-body
offset:
len -= el_off;
For both beacon and probe response frames, el_off is 36. If the frame is
shorter than el_off, subtracting it causes the calculated IE length to
wrap. The length is eventually passed to cfg80211_find_elem_match() as a
very large unsigned value, so the element walk runs beyond the RX skb.
This path is reached from at76_rx_tasklet() while scanning. If the device
delivers a truncated beacon or probe response, the oversized IE length
causes an out-of-bounds read during scanning.
Skip the IE lookup if the frame does not reach the variable elements,
before subtracting el_off.
Fixes: 1264b95146 ("at76c50x-usb: add driver")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Huihui Huang <hhhuang@smu.edu.sg>
Link: https://patch.msgid.link/20260715140815.1242033-1-hhhuang@smu.edu.sg
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Hardware implementations report Scalable-Mode Page-walk Coherency Support
via the SMPWCS field in the extended capability register. If the hardware
does not support page-walk coherency, a clflush is required every time
the page table entries (which are walked by the IOMMU hardware) are
updated.
In the SVA case, page tables are managed by the CPU mm core, not by the
IOMMU driver. Because the IOMMU driver has no way of knowing whether the
CPU page table management code has ensured coherency via clflush, the
driver must deny SVA if the hardware does not support coherent paging.
Fixes: ff3dc6521f ("iommu/vt-d: Fix CPU and IOMMU SVM feature matching checks")
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Samiullah Khawaja <skhawaja@google.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
mwifiex_process_uap_event() handles EVENT_UAP_STA_ASSOC by exposing the
(re)association request IEs that the firmware copies into the event:
sinfo->assoc_req_ies = &event->data[len];
len = (u8 *)sinfo->assoc_req_ies - (u8 *)&event->frame_control;
sinfo->assoc_req_ies_len = le16_to_cpu(event->len) - (u16)len;
event->len is supplied by the device firmware and is never validated,
and the subtraction is unchecked. assoc_req_ies points into
adapter->event_body[MAX_EVENT_SIZE], a fixed-size array embedded in the
kmalloc()'d struct mwifiex_adapter.
On the ap_11n_enabled path mwifiex_set_sta_ht_cap() walks these IEs with
cfg80211_find_ie(), whose for_each_element() loop dereferences each
element header. A firmware-reported event->len larger than the bytes
actually received makes assoc_req_ies_len describe IEs that extend past
event_body, so the walk reads out of the adapter slab object, a
slab-out-of-bounds read (KASAN: slab-out-of-bounds in cfg80211_find_ie).
An event->len smaller than the header instead makes the int subtraction
negative, which wraps to a huge size_t when stored in assoc_req_ies_len.
The same length is handed to cfg80211_new_sta(), so a more modest
over-claim can also copy stale event_body bytes into the
NL80211_CMD_NEW_STATION notification.
A malicious or malfunctioning mwifiex device (USB/SDIO/PCIe) can deliver
such an event while the interface is in AP/uAP mode.
Validate event->len before use: reject a length that underflows the
header or that would place the IEs outside the event_body[] buffer the
event was copied into. event->len here is struct mwifiex_assoc_event.len,
a payload field internal to this event, not the transport frame length,
so it is validated in this handler rather than at the generic
MWIFIEX_TYPE_EVENT receive path, which only sees the event cause and the
transport frame length. The bound is against event_body[MAX_EVENT_SIZE]
rather than the actually-received length because the transports store the
event differently (USB and SDIO leave the 4-byte event header in
event_skb, PCIe strips it via skb_pull), whereas event_body is the single
fixed buffer all of them copy the event into. This is the event-path
analogue of the receive-path bounds checks added in commit 1195852816
("wifi: mwifiex: Fix OOB and integer underflow when rx packets").
Fixes: e568634ae7 ("mwifiex: add AP event handling framework")
Signed-off-by: HE WEI (ギカク) <skyexpoc@gmail.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20260715135711.34688-1-skyexpoc@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This information can be considered part of the capabilities and should
also be copied to the NAN data station.
Fixes: 27e9b326b6 ("wifi: mac80211: support NAN stations")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260714141038.15620aa5324b.I049254b854ac91c32e0768eb7c819f32eda34218@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When vhost owns the virtio-net header, i.e. when
VHOST_NET_F_VIRTIO_NET_HDR is negotiated, sock_hlen is 0,
meaning that no header will be forwarded to the TAP device.
In the current vhost_net_build_xdp() implementation,
when sock_hlen == 0, the gso pointer can point at the start of the
Ethernet frame instead of a virtio-net header.
This results in a wrong interpretation of the destination MAC address
bytes as struct virtio_net_hdr fields.
This can, for some MAC addresses, trigger -EINVAL and return early
before the TX descriptor is completed, which can stall vhost-net TX.
Before 97b2409f28, the gso pointer was set to the zeroed padding area,
using it as a synthetic virtio-net header. Restore that behavior.
Fixes: 97b2409f28 ("vhost-net: reduce one userspace copy when building XDP buff")
Signed-off-by: Enrico Zanda <enrico.zanda@arm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://patch.msgid.link/20260708152242.2268848-1-enrico.zanda@arm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
wilc_parse_assoc_resp_info() computes the trailing IE length as
ies_len = buffer_len - sizeof(*res);
without first checking that buffer_len is at least sizeof(struct
wilc_assoc_resp) (6 bytes). buffer_len is the length reported for a
received association response (host_int_parse_assoc_resp_info() passes
hif_drv->assoc_resp / assoc_resp_info_len straight in) and must be
validated before the driver accesses the fixed header.
For a frame shorter than the 6-byte fixed header, the subtraction wraps.
For a four-byte response the result is truncated to a u16 ies_len of
65534, so kmemdup() then attempts to copy 65534 bytes starting at
buffer + sizeof(*res), beyond the valid association-response data
(CWE-125). A response shorter than four bytes can also cause an
out-of-bounds read of res->status_code at offsets 2 and 3.
Reject frames too short to hold the fixed header before touching the
header or computing ies_len. Also set the connection status to a failure
on this path: the caller falls through to a
"conn_info->status == WLAN_STATUS_SUCCESS" check after the parser
returns, so leaving the status untouched could let a malformed short
response be treated as a successful association.
Fixes: c5c77ba18e ("staging: wilc1000: Add SDIO/SPI 802.11 driver")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Huihui Huang <hhhuang@smu.edu.sg>
Link: https://patch.msgid.link/20260714091811.3596126-1-hhhuang@smu.edu.sg
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The most significant change is to fix an ath12k regression which led
to low MLO RX throughput on WCN7850.
The remainder are an assortment of minor bug fixes spread across many
of the ath drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCalUE+AAKCRAsFbugiYzL
e41eAQD9fk23dZo0OlT3lWl4AO2VmUECeXFZ0SqCGMQ828t07wEA1NF/1Nzyf7xV
6S4gOVCX+lX8lm9AISx8lBcA6llb5g8=
=aNPp
-----END PGP SIGNATURE-----
Merge tag 'ath-current-20260713' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git update for v7.2-rc4
The most significant change is to fix an ath12k regression which led
to low MLO RX throughput on WCN7850.
The remainder are an assortment of minor bug fixes spread across many
of the ath drivers.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix regression in rgpower table loading, caused by using
request_firmware(): when the requested firmware does not exist, e.g.
nxp/rgpower_WW.bin does not exist on OpenWRT builds for WRT3200ACM,
request_firmware() falls back to firmware_fallback_sysfs(), which expects
the firmware to be provided by user space using SYSFS. No such utility is
provided in this configuration, so the entire system locks up for 60
seconds, until the request times out. During this time, no other log
messages are observed, and the device does not respond to commands over
UART.
The request_firmware() call is performed in the following context:
current->comm kworker/1:2 in_task 1 irqs_disabled 0 in_atomic 0
Fixed by using request_firmware_direct(). This prevents fallback to SYSFS,
and avoids delay. The rgpower table is optional. The driver falls back
to the device tree power table if the firmware is not present.
The error code is printed for debugging and returned to the caller,
which only cares for success or failure, so there are no side effects.
Fixes: 7b6f16a258 ("wifi: mwifiex: add rgpower table loading support")
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20260712221709.7099-1-gvalkov@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The program header scan handles PT_INTERP from a switch nested in the
scan loop, so its break leaves the switch and not the loop. A binary
carrying more than one PT_INTERP runs the case again and overwrites both
interpreter_name and interpreter. The previous name allocation leaks and
so does the previous interpreter reference, along with the write denial
open_exec() took on it. The denial is never released, so the file stays
unwritable for as long as the system runs.
An unprivileged caller reaches this with a crafted binary and repeats it
at will. binfmt_elf stops at the first PT_INTERP. Do the same here.
The flaw dates back to the driver's introduction in the pre-git history
tree introduced in v2.6.11 by 91808d6ebe39 ("[PATCH] FRV: Add FDPIC ELF
binary format driver").
Link: https://patch.msgid.link/20260721-gezittert-medium-kreide-b41fc1f0277e@brauner
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: Jori Koolstra <jkoolstra@xs4all.nl>
Signed-off-by: Christian Brauner (Amutable) <brauner@kernel.org>
wanxl_pci_init_one() stores the freshly allocated card in driver data
before the PLX BAR is mapped. Several early probe failures then unwind
through wanxl_pci_remove_one(), including failure to allocate the coherent
status area or to restore the DMA mask.
wanxl_pci_remove_one() unconditionally calls wanxl_reset(), and
wanxl_reset() dereferences card->plx. On those early failures card->plx
is still NULL, so the error path can dereference a NULL MMIO pointer.
Only issue the hardware reset once the BAR mapping exists. The remaining
cleanup in wanxl_pci_remove_one() already checks whether later resources
were allocated.
This issue was found by a static analysis checker and confirmed by
manual source review.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
Link: https://patch.msgid.link/20260708143415.3169358-1-ruoyuw560@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
nfp_cpp_resource_find() allocates a CPP mutex handle for the matching
resource-table entry and then reports success. nfp_resource_try_acquire()
immediately passes that handle to nfp_cpp_mutex_trylock().
However, nfp_cpp_mutex_alloc() returns NULL on failure. If that happens
for a matching table entry, the resource lookup still returns success and
the following trylock dereferences a NULL mutex pointer while opening the
resource.
nfp_resource_acquire() already treats failure to allocate the table mutex
as -ENOMEM. Do the same for the resource mutex and fail the lookup before
publishing the rest of the resource handle.
This issue was found by a static analysis checker and confirmed by
manual source review.
Fixes: f01a216157 ("nfp: add support for resources")
Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260708143408.3168425-1-ruoyuw560@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When ieee80211_vif_update_links() adds new links it allocates a link
container for each and calls ieee80211_link_init() (which registers the
per-link debugfs files with file->private_data pointing into the container)
and ieee80211_link_setup(). If the subsequent drv_change_vif_links() fails,
the error path restores the old pointers and jumps to 'free', which frees
the new containers but never removes their debugfs entries or stops the
links. The debugfs files survive with file->private_data dangling at the
freed container, so a later open()+read() (e.g. link-1/txpower)
dereferences freed memory in ieee80211_if_read_link(), a use-after-free.
The removal path already dismantles links correctly via
ieee80211_tear_down_links(), which removes each link's keys and debugfs
entries and calls ieee80211_link_stop(); the add path on the error branch
does not. Commit be1ba9ed22 ("wifi: mac80211: avoid weird state in error
path") hardened this same error path for the link-removal case
(new_links == 0) but left the newly-added links' teardown unaddressed.
drv_change_vif_links() can fail at runtime on MLO drivers (internal
allocation / queue / firmware command failures).
Remove the new links' debugfs entries and stop them before freeing.
BUG: KASAN: slab-use-after-free in ieee80211_if_read_link (net/mac80211/debugfs_netdev.c:127)
Read of size 8 at addr ffff888011290000 by task exploit/145
Call Trace:
...
ieee80211_if_read_link (net/mac80211/debugfs_netdev.c:127)
short_proxy_read (fs/debugfs/file.c:373)
vfs_read (fs/read_write.c:572)
ksys_read (fs/read_write.c:716)
do_syscall_64 (arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
...
Oops: general protection fault, probably for non-canonical address 0xdffffc000000000a
RIP: 0010:ieee80211_if_read_link (net/mac80211/debugfs_netdev.c:127)
Kernel panic - not syncing: Fatal exception
Fixes: 170cd6a66d ("wifi: mac80211: add netdev per-link debugfs data and driver hook")
Reported-by: Weiming Shi <bestswngs@gmail.com>
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Link: https://patch.msgid.link/20260711210302.2098404-1-xmei5@asu.edu
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The stop value is derived from bprm->p >> PAGE_SHIFT. The index variable
is an unsigned long. If bprm->p drops below PAGE_SIZE and stop becomes
zero the loop condition index >= stop is always true.
After the index == 0 iteration the decrement wraps to ULONG_MAX and
bprm->page[ULONG_MAX] reads sizeof(void *) bytes in front of the array.
The pointer has wrapped to -1. That garbage pointer is then passed to
kmap_local_page() and PAGE_SIZE bytes are copied from wherever that
lands into the stack of the process being created. And the loop doesn't
terminate either...
Getting there only requires bprm->p < PAGE_SIZE. On !MMU
bprm_set_stack_limit() and bprm_hit_stack_limit() are empty. So the only
constraint on how far bprm->p is pushed down is valid_arg_len(), i.e.
that each individual string still fits in what is left.
bprm->p starts at PAGE_SIZE * MAX_ARG_PAGES - sizeof(void *) so a
single argument or environment string of a little over 31 pages leaves
it in the first page:
Oops - load access fault [#1]
CPU: 0 UID: 0 PID: 1 Comm: victim Not tainted 7.2.0-rc4 #1
epc : __memcpy+0xd4/0xf8
ra : transfer_args_to_stack+0xaa/0xae
s4 : ffffffffffffffff s2 : 0000000000000000
a1 : ffffffdc98000000 a2 : 0000000000001000
status: 0000000a00001880 badaddr: ffffffdc98000000 cause: 0000000000000005
[<801a5324>] __memcpy+0xd4/0xf8
[<800d5f6a>] load_flat_binary+0x43a/0x65e
[<800a2de4>] bprm_execve+0x1d4/0x316
[<800a351a>] do_execveat_common+0x12e/0x138
[<800a3d44>] __riscv_sys_execve+0x38/0x4e
Kernel panic - not syncing: Fatal exception in interrupt
This is an arcane bug but we should still fix it.
Count down from MAX_ARG_PAGES so the loop ends when index reaches stop,
stop == 0 included. The iterations performed are unchanged for every
other value of stop.
Only CONFIG_MMU=n builds are affected, transfer_args_to_stack() is used
by binfmt_flat and binfmt_elf_fdpic on nommu only.
The loop predates git history. commit 7e7ec6a934
("elf_fdpic_transfer_args_to_stack(): make it generic") only moved it
from binfmt_elf_fdpic.c into fs/exec.c and narrowed the copy to the used
part of the first page. The condition and the decrement are unchanged
from 2.6.12-rc2.
Link: https://patch.msgid.link/20260721-hochachtung-staumauer-pigmente-15d71f7d7d04@brauner
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: David Hildenbrand (Arm) <david@kernel.org>
Signed-off-by: Christian Brauner (Amutable) <brauner@kernel.org>
need_sync is a per-IOMMU flag shared by all domains and devices behind
that IOMMU. It is set whenever a command is queued with sync == true and
cleared when a completion-wait (CWAIT) command is queued. However, a
cleared need_sync only means that a covering CWAIT has been queued, not
that all previously queued commands have actually completed in hardware.
iommu_completion_wait() read need_sync locklessly and returned early
when it was false. This breaks the "block until all previously queued
commands have completed" contract in a multi-CPU scenario:
CPU2: queue inv-B => need_sync = true
CPU1: queue CWAIT(N); need_sync = false; then wait_on_sem(N)
CPU2: read need_sync == false => return 0 (no wait!)
CPU2 returns without waiting for any sequence number even though its
inv-B may not have completed yet (CWAIT(N), queued after inv-B, has not
been signaled). CPU2 then proceeds to, for example, free page-table
pages while the IOMMU can still walk stale translations, opening a
use-after-free window. This is a logical race in the meaning of the
flag, not a memory-visibility issue, so barriers alone do not help.
Fix it without losing the optimization of avoiding redundant CWAIT
commands: take iommu->lock before testing need_sync, and when it is
false do not return early but wait for the last allocated sequence
number (cmd_sem_val). Since need_sync == false implies no sync command
was queued after the last CWAIT, that CWAIT is FIFO-ordered after every
not-yet-completed command, so waiting for its sequence number guarantees
all prior commands (possibly queued by another CPU) have completed. The
common path with pending work is unchanged and no extra hardware command
is issued.
Signed-off-by: Guanghui Feng <guanghuifeng@linux.alibaba.com>
Fixes: 815b33fdc2 ("x86/amd-iommu: Cleanup completion-wait handling")
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Will Deacon <will@kernel.org>
- Avoid redundant page-table allocations in ioremap pcache topup
- Apply SBI FWFT LOCK flag only on successful set
- Bound SBI PMU counter mask scan to BITS_PER_LONG
- Skip TLB flush when G-stage PTE becomes valid with Svvptc
- Zicbo[m|z|p] block sizes should be always present in ONE_REG
- Inject instruction access fault on unmapped guest fetch
- Serialize virtual interrupt pending state updates using raw spinlock
- Fix Spectre-v1 in vector register access via ONE_REG
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEZdn75s5e6LHDQ+f/rUjsVaLHLAcFAmpbMVwACgkQrUjsVaLH
LAdENhAAi5eWE2WACOp50yy+e9/K/n7WFyGsnAg1u157HR0ywBIfOKA9Q3fGnHs/
WUeqXjtjnVLJFB/LfG3aF9O4PLyU+iZ2g7On5O4ZXQMY2wpueHBZ2fyvUFmrWKl6
JwwgluMxeX1IIhJdhSe0hUU8sxcurYtmuxMKO/2lkYcqxfn6UGpBHONkNGVBncsJ
RcaU2lQBnv+8hJ0wlCb0hep9R34YkjF1rmti71tru7XqnF3rq2Z5PBITjfBHXmeB
6iYvVnpSvPiEvxF8454dvQ9bbXmh3OS+ncI/qjS1u2fkrQrM00eZs2bKzUpW7LlG
7ZA5Rm+EQPbHoPV1EKHXXip7uSZ7U8nm9CxMCADI7zZi1K3qvKnnRtA4MahLxO2o
WSxWEW7ONHskZWz1YZUyqpPCutJQOtKaIu7ITzS0aHep9UB/3Lrs1sA9hRTEINUl
9O1Nusro+wdlG1SsycWXPNoyHvEnN1h2FjWLRpr54X9mEQtCCg0/qNvwo6CPZNwH
E9lWgx7rcFnmy24ln01fHOtTD5IKRNis2MUswqNVyc3X7gOft+w8/1QE/MHYC9cl
LF7b12xCOFp1PMkicgVYwWRQ+6qrvidFvWOWqVtcRmfMw6TjXIrB5Fr/MYg8gBL/
N6uzyk3+UmSiFehbElXww3YEiqd81KzKgeEsU74/T2yyAEflVYA=
=jcT0
-----END PGP SIGNATURE-----
Merge tag 'kvm-riscv-fixes-7.2-1' of https://github.com/kvm-riscv/linux into HEAD
KVM/riscv fixes for 7.2, take #1
- Avoid redundant page-table allocations in ioremap pcache topup
- Apply SBI FWFT LOCK flag only on successful set
- Bound SBI PMU counter mask scan to BITS_PER_LONG
- Skip TLB flush when G-stage PTE becomes valid with Svvptc
- Zicbo[m|z|p] block sizes should be always present in ONE_REG
- Inject instruction access fault on unmapped guest fetch
- Serialize virtual interrupt pending state updates using raw spinlock
- Fix Spectre-v1 in vector register access via ONE_REG
On Intel platforms with a VMX preemption timer and APICv, if a VMM
calls KVM_GET_LAPIC before KVM_GET_MSRS to save the vCPU state, it is
possible to lose a pending timer interrupt.
If the thread running these ioctls is migrated to another core after
calling KVM_GET_LAPIC but before KVM_GET_MSRS and the guest is using
their LAPIC timer in TSC-deadline mode, not only does the save LAPIC
state not carry the pending interrupt, the TSCDEADLINE MSR will be
zeroed.
After migration across CPUs, KVM_GET_MSRS calls vcpu_load, posting the
interrupt and clearing the MSR:
vcpu_load() ->
kvm_arch_vcpu_load() ->
kvm_lapic_restart_hv_timer() ->
start_hv_timer() ->
apic_timer_expired() ->
kvm_apic_inject_pending_timer_irqs()
. post interrupt into the LAPIC state
. clear IA32_TSCDEADLINE
The saved LAPIC state will be missing the pending interrupt and the saved
MSR will be zero. Oops.
Fix by only posting an interrupt when we're attempting to enter the guest
(vcpu->wants_to_run == true), not for vcpu_load from other paths.
Assisted-by: gemini:gemini-3.1-pro-preview
Debugged-by: David Matlack <dmatlack@google.com>
Debugged-by: Sean Christopherson <seanjc@google.com>
Debugged-by: Jim Mattson <jmattson@google.com>
Debugged-by: James Houghton <jthoughton@google.com>
Signed-off-by: Venkatesh Srinivas <venkateshs@chromium.org>
Message-ID: <20260715234234.15382-2-venkateshs@chromium.org>
Reviewed-by: James Houghton <jthoughton@google.com>
Reviewed-by: Chao Gao <chao.gao@intel.com>
Cc: stable@vger.kernel.org
Fixes: ae95f566b3 ("KVM: X86: TSCDEADLINE MSR emulation fastpath", 2020-05-15)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
