There's nothing special here to prevent compilation on non ARM hosts.
Matches every other st phy driver.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://patch.msgid.link/20260306222457.8400-2-rosenp@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
EyeQ5 embeds a system-controller called OLB. It features many unrelated
registers, and some of those are registers used to configure the
integration of the RGMII/SGMII Cadence PHY used by MACB/GEM instances.
Wrap in a neat generic PHY provider, exposing two PHYs with standard
phy_init() / phy_set_mode() / phy_power_on() operations.
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20260309-macb-phy-v9-1-5afd87d9db43@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix a malformed MODULE_AUTHOR macro in the RZ/G3E USB3.0 PHY driver where
the author's name and opening angle bracket were missing, leaving only the
email address with a stray closing >. Correct it to the standard Name
<email> format.
Reported-by: Pavel Machek <pavel@nabladev.com>
Closes: https://lore.kernel.org/all/abp4KprlYyU+jMPu@duo.ucw.cz/
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20260319063211.5056-1-biju.das.jz@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When clk_enable() fails, the clock was never enabled. Calling
clk_disable() in this error path is incorrect.
Remove the spurious clk_disable() call from the error handling
in spacemit_usb2phy_init().
Fixes: fe4bc1a086 ("phy: spacemit: support K1 USB2.0 PHY controller")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Reviewed-by: Ze Huang <huang.ze@linux.dev>
Link: https://patch.msgid.link/20260326-k1-usb3-v1-1-0c2b6adf5185@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On Layerscape, some Lynx SerDes consumers go through the PHY framework
(we call these 'managed' for the sake of this discussion; they are some
Ethernet lanes), and some consumers don't go through the PHY framework
(we call these 'unmanaged'; they are some unconverted Ethernet lanes,
plus all SATA and PCIe controllers).
A lane is initially unmanaged, and becomes managed when phy_init() is
called on it. Similarly, it becomes unmanaged again when phy_exit() is
called.
Managed lanes are supposed to have power management through
phy_power_on() and phy_power_off().
The lynx-28g SerDes driver, when it probes, probes on all lanes, but
needs to be careful to keep the unmanaged lanes powered on, because
those might be in use by consumers unaware that they need to call
phy_init() and phy_power_on(). This also applies after phy_exit() is
called - no guarantee is made about how the port may be used
afterwards - may be DPDK, may be something else which is unaware of
the PHY framework.
Given this state table:
State | Consumer calls phy_exit()? | Provider implements phy_exit()?
-------+----------------------------+--------------------------------
(a) | no | no
(b) | no | yes
(c) | yes | no
(d) | yes | yes
we are currently in state (a). This has the problem that when the
consumer fails to probe with -EPROBE_DEFER or is otherwise unbound,
the phy->init_count remains elevated and the lane never returns to the
unmanaged state (temporarily or not) as it should. Furthermore, the
second and subsequent phy_init() consumer calls are never passed on to
the provider driver.
We solve the above problem by implementing phy_exit() in the consumer,
and that moves us to state (c). But this creates the problem that a
balanced set of phy_init() and phy_exit() calls from the consumer will
effectively result in multiple lynx_28g_init() calls as seen by the
SerDes and nothing else - as the optional phy_ops :: exit() is not
implemented. But that actually doesn't work - the 28G Lynx SerDes can't
power down a lane which is already powered down; that call sequence
would time out and fail.
So actually we want to be in state (d), where both the provider and the
consumer implement phy_exit(). But we can only do that safely through
intermediary state (b), where the provider implements it first. This
effectively behaves just like (a), except it offers a safe migration
path for the consumer to call phy_exit() as mandated by the Generic PHY
API.
Extra development notes: ignoring the lynx_28g_power_on() error in
lynx_28g_exit() is a deliberate decision. The consumer can't deal with a
teardown path that is not error-free. Ignoring the error is not silent:
lynx_28g_power_on() -> lynx_28g_lane_reset() will print on failure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260321011451.1557091-4-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current procedure for power_off() and power_on() is the same as the
one used for major lane reconfiguration, aka halting. But this is
incorrect.
One would expect that a powered off lane causes the CDR (clock and data
recovery) loop of the link partner to lose lock onto its RX stream
(which suggests there are no longer any bit transitions => the channel
is inactive). However, it can be observed that this does not take place
(the CDR lock is still there), which means that a halted lane is not
powered off.
Implement the procedure mentioned in the block guide for powering down
a lane, and then back on. This means:
- lynx_28g_power_off() currently emits a HLT_REQ and waits for it to
clear. Rename it to lynx_28g_lane_halt() and keep using it for
lynx_28g_set_mode().
- lynx_28g_power_on() currently emits a RST_REQ and waits for it to
clear. This is the reset procedure - rename it to
lynx_28g_lane_reset(), and keep using it for lynx_28g_set_mode().
The "real" lynx_28g_power_off() should emit a STP_REQ and wait for it to
clear. And the "real" lynx_28g_power_on() should clear the DIS bit and
then perform a lane reset. Hook these methods to the phy_ops ::
power_off() and power_on() instead.
As opposed to lynx_28g_power_off() which is also directly hooked to the
PHY API, lynx_28g_lane_halt() isn't; just to lynx_28g_set_mode(), and
the call is being made in a state where we haven't yet made any change
to the lane. So it does make some limited amount of sense to code this
up such that if it fails, we make an attempt to reset the lane anyway
and let the consumer know that phy_set_mode_ext() failed.
Sort the field definitions in LNaTRSTCTL and LNaRRSTCTL in descending
order, and add new definitions for STP_REQ and DIS, previously unused.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260321011451.1557091-3-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are various circumstances in which a lane halt, or a lane reset,
will fail to complete. If this happens, it will hang the kernel, which
only implements a busy loop with no timeout.
The circumstances in which this will happen are all bugs in nature:
- if we try to power off a powered off lane
- if we try to power off a lane that uses a PLL locked onto the wrong
refclk frequency (wrong RCW, but SoC boots anyway)
Actually, unbounded loops in the kernel are a bad practice, so let's use
read_poll_timeout() with a custom function that reads both LNaTRSTCTL
(lane transmit control register) and LNaRRSTCTL (lane receive control
register) and returns true when the request is done in both directions.
The HLT_REQ bit has to clear, whereas the RST_DONE bit has to get set.
Any time such an error happens, it is catastrophic and there is no point
in trying to propagate it to our callers:
- if lynx_28g_set_mode() -> lynx_28g_power_on() times out, we have
already reconfigured the lane, but returning an error would tell the
caller that we didn't
- if lynx_28g_power_off() times out, again not much for the consumer to
do to help get out of this situation - the phy_power_off() call is
probably made from a context that the consumer can't cancel, or it is
making it to return to a known state from a previous failure.
So just print an error if timeouts happen and let the driver control
flow continue. The entire point is just to not let the kernel freeze.
Suggested-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/lkml/d0c8bbf8-a0c5-469f-a148-de2235948c0f@solid-run.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260321011451.1557091-2-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A repeater is not required for the PHY to function. On systems with
multiple PHY instances connected to a multi-port controller, some PHYs
may be unconnected. All PHYs must still probe successfully even without
attached repeaters, otherwise the controller probe fails.
So make it optional.
Signed-off-by: Wesley Cheng <wesley.cheng@oss.qualcomm.com>
[abel.vesa@oss.qualcomm.com: commit re-worded to reflect actual reason]
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260302-phy-qcom-m31-eusb2-make-repeater-optional-v2-1-dbf714c72056@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 81af9e40e2 ("phy: qcom: qmp-ufs: Fix SM8650 PCS table for Gear 4")
moved QPHY_V6_PCS_UFS_PLL_CNTL register configuration from the shared
sm8650_ufsphy_g5_pcs table to the SM8650-specific sm8650_ufsphy_pcs base
table to fix Gear 4 operation on SM8650.
However, this change inadvertently broke kaanapali and SM8750 SoCs
which also rely on the shared sm8650_ufsphy_g5_pcs table for Gear 5
configuration but use their own sm8750_ufsphy_pcs base table. After the
change, kaanapali PHYs are left without the required PLL_CNTL = 0x33
setting, causing the PHY PLL to remain at its hardware reset default
value, preventing PLL lock and resulting in DME_LINKSTARTUP timeouts.
Fix this by adding the missing QPHY_V6_PCS_UFS_PLL_CNTL = 0x33 entry
to the sm8750_ufsphy_pcs table, mirroring what the original commit
already did for sm8650_ufsphy_pcs.
Cc: stable@vger.kernel.org # v6.19.12
Fixes: 81af9e40e2 ("phy: qcom: qmp-ufs: Fix SM8650 PCS table for Gear 4")
Signed-off-by: Nitin Rawat <nitin.rawat@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260415104851.2763238-1-nitin.rawat@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing PHYPARAM0 tuning values for Exynos7870 are incorrect,
causing the USB 2.0 PHY to fail high-speed negotiation and fall back
to full-speed (12Mbps) operation.
Fix TXVREFTUNE (transmitter voltage reference) from 14 to 3,
TXRESTUNE (transmitter impedance) from 3 to 2, and SQRXTUNE
(squelch threshold) from 6 to 5. Also explicitly set
TXPREEMPPULSETUNE to 0, which was previously missing from the
tuning table despite being included in the register mask.
All values are derived from the vendor kernel for the Samsung
Galaxy A6 (SM-A600FN), as no public hardware documentation is
available for the Exynos7870 USB DRD PHY. With these corrections,
the PHY successfully negotiates high-speed (480Mbps) operation.
Fixes: 588d5d20ca ("phy: exynos5-usbdrd: add exynos7870 USBDRD support")
Cc: stable@vger.kernel.org
Tested-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Łukasz Lebiedziński <kernel@lvkasz.us>
Link: https://patch.msgid.link/20260406135627.234835-1-kernel@lvkasz.us
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code reads a single hs_term_range_adj value from bit field
[10:7] of FUSE_SKU_CALIB_0 and applies it to all USB2 pads uniformly.
However, on SoCs that support per-pad termination, each pad has its own
hs_term_range_adj field: pad 0 in FUSE_SKU_CALIB_0[10:7], and pads 1-3
in FUSE_USB_CALIB_EXT_0 at bit offsets [8:5], [12:9], and [16:13]
respectively.
Fix the calibration by reading per-pad values from the appropriate fuse
registers. For SoCs that do not support per-pad termination, replicate
pad 0's value to all pads to maintain existing behavior.
Add a has_per_pad_term flag to the SoC data to indicate whether per-pad
termination values are available in FUSE_USB_CALIB_EXT_0.
Fixes: 1ef535c6ba ("phy: tegra: xusb: Add Tegra194 support")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Wei-Cheng Chen <weichengc@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260504033305.2283145-1-weichengc@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The initial sa8775p eDP PHY binding contribution missed adding support for
voting on the eDP reference clock. This went unnoticed because the UFS PHY
driver happened to enable the same clock.
After commit 77d2fa54a9 ("scsi: ufs: qcom : Refactor phy_power_on/off
calls"), the eDP reference clock is no longer kept enabled, which results
in the following PHY power-on failure:
phy phy-aec2a00.phy.10: phy poweron failed --> -110
To fix this, explicit voting for the eDP reference clock is required.
This patch adds the eDP reference clock for sa8775p eDP PHY and updates
the corresponding example node.
Signed-off-by: Ritesh Kumar <quic_riteshk@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260128114853.2543416-2-quic_riteshk@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 81791c45c8 ("phy: qcom: qmp-usbc: Add QCS615 USB/DP PHY config
and DP mode support") chose to name QCS615 DP PHY variables/functions
with qmp_v2 prefix, by assuming that QMP PHY registers are versioned
as a whole. However, the reality is that the registers are versioned
in sub-modules like QSERDES COM and QSERDES TXRX respectively, e.g.
QCS615 DP PHY has registers of QSERDES COM v2 and QSERDES TXRX v3.
Thus it may cause confusion that qmp_v2_xxx table and functions access
QSERDES TXRX v3 registers.
Rename QCS615 DP PHY variables and functions to be prefixed by qcs615
instead of qmp_v2. This better aligns with how the driver names USB3 PHY
variables for QCM2290 etc.
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Link: https://patch.msgid.link/20260314051325.198137-5-shengchao.guo@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The register definitions in header qserdes-txrx-v2 and qserdes-txrx-v3
are actually identical. Considering that QSERDES TX/RX v2 is already
defined by header qserdes-txrx, qserdes-txrx-v2 is really just
a duplication of qserdes-txrx-v3 for QSERDES TX/RX v3. Switch
qcom-qmp-usbc driver to use v3 registers.
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260314051325.198137-4-shengchao.guo@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As the code comments in the headers say, both qserdes-com and
qserdes-com-v2 define QSERDES COM registers for QMP V2 PHY. Switch
phy-qcom-qmp drivers to use register definitions in qserdes-com-v2
to make the QSERDES COM version explicit.
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260314051325.198137-3-shengchao.guo@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A few registers that could be used by phy-qcom-qmp drivers are missing
from qserdes-com-v2 header. Add them.
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260314051325.198137-2-shengchao.guo@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The mvebu_a3700_utmi_phy_power_off() function tries to modify the
USB2_PHY_CTRL register by using the IO address of the PHY IP block along
with the readl/writel IO accessors. However, the register exist in the
USB miscellaneous register space, and as such it must be accessed via
regmap like it is done in the mvebu_a3700_utmi_phy_power_on() function.
Change the code to use regmap_update_bits() for modífying the register
to fix this.
Fixes: cc8b7a0ae8 ("phy: add A3700 UTMI PHY driver")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20260321-a3700-utmi-fix-usb2_phy_ctrl-access-v1-1-6005ff4b5058@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
kconfiglint reports:
K006: config PHY_TEGRA_XUSB selects USB_CONN_GPIO which depends on
GPIOLIB, but PHY_TEGRA_XUSB does not depend on GPIOLIB
K002: config PHY_TEGRA_XUSB selects visible symbol USB_CONN_GPIO
which has dependencies
USB_CONN_GPIO was introduced in commit 4602f3bff2 ("usb: common: add USB
GPIO based connection detection driver") with a hard dependency on GPIOLIB,
since it needs GPIO pins to detect USB cable connection state.
Commit f67213cee2 ("phy: tegra: xusb: Add usb-role-switch support") added
`select USB_CONN_GPIO` to PHY_TEGRA_XUSB to support USB role switching via
GPIO-based detection. At that time, PHY_TEGRA_XUSB depended only on
`ARCH_TEGRA`, and both the ARM32 and ARM64 ARCH_TEGRA Kconfig definitions
select GPIOLIB, so the missing explicit GPIOLIB guard was not a functional
problem — GPIOLIB is always available when ARCH_TEGRA is enabled.
Later, commit 0d5c9bc7c6 ("phy: tegra: Select USB_COMMON for
usb_get_maximum_speed()") added `depends on USB_SUPPORT` but still did not
address the GPIOLIB gap.
The select can force USB_CONN_GPIO on without its GPIOLIB dependency being
satisfied if the Kconfig dependencies were ever restructured. Make the
select conditional with `select USB_CONN_GPIO if GPIOLIB` to make the
dependency explicit. This mirrors how other drivers handle optional
GPIO-dependent selects throughout the kernel.
Assisted-by: Claude:claude-opus-4-6 kconfiglint
Signed-off-by: Sasha Levin <sashal@kernel.org>
Link: https://patch.msgid.link/20260426000309.54959-1-sashal@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 5fff41e1f8 ("IB/core: Fix race condition in resolving IP to MAC")
changed the workqueue "addr_wq" to a single-threaded wq.
Commit e19c0d2378 ("RDMA/rdma_cm: Remove process_req and timer sorting")
eliminated global work and started using per-req work.
Now we no longer have the race, change "addr_wq" back to multi-threaded
workqueue to speed up multiple addr resolutions.
Signed-off-by: Surabhi Gogte <sgogte@purestorage.com>
Link: https://patch.msgid.link/20260410001549.3149060-1-sgogte@purestorage.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Document the compatible for the USB QMP PHY found on the Qualcomm Eliza
SoC.
It is fully compatible with the one found on Qualcomm SM8650, so add it
with the SM8650 as fallback.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://patch.msgid.link/20260504-eliza-bindings-qmp-phy-v2-1-849c4de8d75f@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Synopsys eUSB2 PHY found on the Eliza SoC is fully compatible with the
one found the SM8550.
So document it by adding the compatible to the list that has the SM8550
one as fallback.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://patch.msgid.link/20260504-eliza-bindings-phy-eusb2-v2-1-fa3a1fd65ab1@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no point to allow selecting core SoC drivers like interconnects
for Qualcomm ARMv7 SoCs when building ARM64 kernel, and vice versa.
This makes kernel configuration more difficult as many do not remember
the Qualcomm SoCs model names/numbers and their properties like
architecture. No features should be lost because:
1. There won't be a single image for ARMv7 and ARMv8/9 SoCs.
2. Newer ARMv8/9 SoCs won't be running in arm32 emulation mode.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260428-interconnect-qcom-clean-arm64-v1-2-e6bc3f7832db@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
In preparation to adding support for several firmware revisions to be
used for a platform, extract the firmware description data. It
incorporates firmware name, HFI ops and buffer requirements of the
particular firmware build.
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
[bod: Made struct iris_firmware_desc into static consts to pass media CI]
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
The linux-firmware is providing the vpuNN_pM.mbn firmware for SM8250
since August of 2024. Stop using the legacy firmware name
(vpu-1.0/venus.mbn) and switch to the standard firmware name schema
(vpu/vpu20_p4.mbn).
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Finalize the logical separation of the software and hardware interface
descriptions by moving hardware properties to the files specific to the
particular VPU version.
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Having firmware-related fields in platform data results in the tying
platform data to the HFI firmware data rather than the actual hardware.
For example, SM8450 uses Gen2 firmware, so currently its platform data
should be placed next to the other gen2 platforms, although it has the
VPU2.0 core, similar to the one found on SM8250 and SC7280 and so the
hardware-specific platform data is also close to those devices.
Split firmware data to a separate struct, separating hardware-related
data from the firmware interfaces.
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
The HW response time is a constant between platforms. Remove it from the
iris_platform_data structure and use it directly.
Suggested-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
The get_instance() is a callback tightly connected to the HFI
implementation. Move it into the new iris_hfi_sys_ops structure, merging
all core callbacks into a single vtable.
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
There is little point in having two different structures for HFI-related
core ops. Merge both of them into the new iris_hfi_ops structure.
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Calling HFI instance-specific ops should not require double indirection
through the core ops. Split instance-specific ops to a separate struct,
keep a pointer to it in struct iris_inst and set it directly in the
get_instance function.
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
To note that iris_set_num_comv() is gen2-internal, rename it to
iris_hfi_gen2_set_num_comv() and then stop using hfi_ops indirection to
set session property (like other functions in this file do).
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
The set_preset_registers is (currently) common to all supported devices.
Extract it to a iris_vpu_common.c and call it directly from
iris_vpu_power_on(). Later, if any of the devices requires special
handling, it can be sorted out separately.
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
The PAS ID, the authentication service ID, used by the Iris is a
constant and it is not expected to change anytime. Drop it from the
platform data and use the constant instead.
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
With the Iris and Venus driver having more or less feature parity for
"HFI 6xx" platforms and with Iris gaining support for SC7280, flip the
switch. Use Iris by default for SM8250 and SC7280, the platforms which
are supported by both drivers, and use Venus only if Iris is not
compiled at all. Use IS_ENABLED to strip out the code and data
structures which are used by the disabled platforms.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
[bod: Moved two conditional compats inside of one ifdef for ci]
[bod: Changed IS_V6(core) (0) to ((void)(core), 0) for ci]
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
As SC7180 is the only remaining user of the non-TZ / non-PAS setup which
uses the video-firmware subnode, move its definition from the common
schema to the SC7180-specific one.
These properties do not accurately describe the hardware. Future
platforms that are going to support non-TZ setup will use different
semantics and different DT ABI (using the iommu-map property).
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
The only users of the non-PAS setup on SC7280 platform are the ChromeOS
devices, which were cancelled before reaching end users. Iris, the
alternative driver for the same hardware, does not support non-PAS
setup. It is expected that in future both Venus and Iris devices will
use different ABI for non-PAS (EL2) setup.
In order to declare only the future-proof hardware description drop
support for non-PAS setup from the SC7280 Venus schema (breaking almost
non-existing SC7280 ChromeOS devices).
The dropped iommus entry reflects the extra stream, which should not be
treated in the same way as the main one (which doesn't match the usage
described by the iommus definition).
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
On SM8250 most of the video clocks are powered by the MMCX domain, while
the PLL is powered on by the MX domain. Extend the driver to support
scaling both power domains, while keeping compatibility with the
existing DTs, which define only the MX domain.
Fixes: 0aeabfa29a ("media: venus: core: add sm8250 DT compatible and resource data")
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
On SM8250 most of the video clocks are powered by the MMCX domain, while
the PLL is powered on by the MX domain. Extend the driver to support
scaling both power domains, while keeping compatibility with the
existing DTs, which define only the MX domain.
Fixes: 79865252ac ("media: iris: enable video driver probe of SM8250 SoC")
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
First of all, on SM8250 Iris (ex-Venus) core needs to scale clocks which
are powered by the MMCX domain. Add MMCX domain to the list of the power
domain to be used on this platform.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Now as all UBWC configuration bits were migrated to be used or derived
from the global UBWC platform-specific data, drop the unused struct and
field definitions.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Tested-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
The UBWC max_channels spreading is specified in the Iris driver, but it
also can be calculated from the platform UBWC config. Use the platform
UBWC configuration instead of specifying it directly in the source.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Tested-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
The UBWC bank spreading is specified both in the Iris driver and in the
platform UBWC config. Use the platform UBWC configuration instead of
specifying it directly in the source.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Tested-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
