Add necessary DAI links and DAI name prefixes to enable audio playback
over USB/DisplayPort and HDMI. The HDMI port is not yet enabled, but it
should carry respective DAI name prefix regardless.
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251217120051.98198-4-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Sound DAI devices exposing same set of mixers, e.g. each DisplayPort
controller, need to add dedicated prefix for these mixers to avoid
conflicts and to allow ALSA to properly configure given instance.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251217120051.98198-3-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable IRIS to allow using the hardware-accelerated video codecs. The
firmware is not upstream in linux-firmware yet, so users need to copy it
from Windows to qcom/x1e80100/ASUSTeK/vivobook-s15/qcvss8380.mbn (just like
GPU/ADSP/CDSP firmware).
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Maud Spierings <maud_spierings@hotmail.com>
Link: https://lore.kernel.org/r/20251220-asus_usbc_dp-v3-3-5e244d420d0f@hotmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable the HDMI port on left side of the laptop.
The display signal is routed through a simple Displayport to HDMI
bridge.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Maud Spierings <maud_spierings@hotmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251220-asus_usbc_dp-v3-2-5e244d420d0f@hotmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Asus vivobook s15 has two usb type c ports on the left side, these
use parade ps8830 retimers like the others, enable them to also enable
dp altmode
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Maud Spierings <maud_spierings@hotmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251220-asus_usbc_dp-v3-1-5e244d420d0f@hotmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Samsung S5K3M5 image sensor supports only 4-lane MIPI CSI-2 interface,
which makes the sensor data-lanes property redundant, and it can be
safely removed from the board dts file. Noteworthy that the property
value is incorrect, because conventionally lanes enumeration of image
sensors starts from index 1.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20251222023834.3284370-5-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At first voltage supply properties of Samsung S5K3M5 image sensor got
names following a pad name convention for Omnivision image sensors. Now
the property names were corrected in the sensor dt bindings documentation,
and it should be updated in the SM8550-HDK with the Rear Camera Card
board dts file.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20251222023834.3284370-4-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Samsung S5K3M5 image sensor supports only 4-lane MIPI CSI-2 interface,
which makes the sensor data-lanes property redundant, and it can be
safely removed from the board dts file. Noteworthy that the property
value is incorrect, because conventionally lanes enumeration of image
sensors starts from index 1.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20251222023834.3284370-3-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At first voltage supply properties of Samsung S5K3M5 image sensor got
names following a pad name convention for Omnivision image sensors. Now
the property names were corrected in the sensor dt bindings documentation,
and it should be updated in the SM8550-QRD board dts file.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20251222023834.3284370-2-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The DTS code coding style expects lowercase hex for values and unit
addresses.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251223152559.155703-6-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
DTS coding style prefers hyphens instead of underscores in the node
names. Change should be safe, because node names are not considered an
ABI.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251223152559.155703-5-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The DTS code coding style expects exactly one space around '=' and
before '{' characters.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251223152559.155703-4-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device trees for the Qualcomm X1E and X1P-based Microsoft Surface
Pro 11 machines (codenamed 'Denali').
This device is very similar to the Surface Laptop 7 ('Romulus').
Use a similar strategy to x1-asus-zenbook-a14.dtsi so that we can create
x1e and x1p-specific flavors of the device tree without too much code
duplication.
Hardware support is similar to other X1 machines. The most notable
missing features are:
- Touchscreen and pen
- Cameras (and status LEDs)
Signed-off-by: Dale Whinham <daleyo@gmail.com>
Signed-off-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251220-surface-sp11-for-next-v6-4-81f7451edb77@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the compatibles for the Qualcomm-based Microsoft Surface Pro 11,
using its Denali codename.
The LCD models are using the Qualcomm Snapdragon X1 Plus (X1P64100),
the OLED ones are using the Qualcomm Snapdragon X1 Elite (X1E80100).
Due to the difference in how the built-in panel is being handled
between the OLED variant and LCD one, it is required to have two
separate DTBs, so document the compatible string for both variants.
Signed-off-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251220-surface-sp11-for-next-v6-1-81f7451edb77@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Multiport controller on Hamoa EVK platform is connected to Two Type-A
ports. VBUS for each of these ports are provided by a TPS2559QWDRCTQ1
regulator, controlled from PMIC GPIOs.
Add the necessary regulators and GPIO configuration to power these.
Implement connector nodes to embed the vbus supply within them. Since
there is no entity currently that can read vbus supply from a Type-A
connector and control it, mark the supplies as always on.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251219161407.2075701-1-krishna.kurapati@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Conform to the new firmware path scheme.
Includes cosmetic cleanups.
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251222-oneplus6-new-fw-path-v1-4-a2d366f9eb89@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Conform to the new firmware path scheme.
Includes cosmetic cleanups.
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251222-oneplus6-new-fw-path-v1-3-a2d366f9eb89@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Conform to the new firmware path scheme.
Includes cosmetic cleanups.
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251222-oneplus6-new-fw-path-v1-2-a2d366f9eb89@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Conform to the new firmware path scheme.
Includes cosmetic cleanups.
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251222-oneplus6-new-fw-path-v1-1-a2d366f9eb89@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable GPU on both qcs9100-ride platforms and provide the path
for zap shader.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251230-a663-gpu-support-v9-4-186722e25387@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable GPU for lemans-evk platform and provide path for zap
shader.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251230-a663-gpu-support-v9-3-186722e25387@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Unlike the CPU, the GPU does not throttle its speed automatically when it
reaches high temperatures.
Set up GPU cooling by throttling the GPU speed
when reaching 105°C.
Signed-off-by: Gaurav Kohli <quic_gkohli@quicinc.com>
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251230-a663-gpu-support-v9-2-186722e25387@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add gpu and gmu nodes for Lemans chipset. Also, add the speedbin
qfprom node and wire it up with GPU node.
Signed-off-by: Puranam V G Tejaswi <quic_pvgtejas@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251230-a663-gpu-support-v9-1-186722e25387@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
To provide access to camera sensors a Rear Camera Card can be connected
to SM8650-HDK board, the camera sensors are:
* Samsung S5K33D ToF camera sensor, connected to CSI0 over MIPI D-PHY,
* Sony IMX766 Wide camera sensor, connected to CSI1 over MIPI C-PHY,
* Omnivision OV64B Ultrawide camera sensor, connected to CSI2 over MIPI C-PHY,
* Samsung S5KJN1 Tele camera sensor, connected to CSI3 over MIPI D-PHY).
Get the initial support of Samsung S5KJN1 camera sensor and two flash leds
on the Rear Camera Card board by adding a board overlay.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20251204041505.131891-5-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support of Samsung S5KJN1 camera sensor connected to CSIPHY3 over
MIPI D-PHY interface.
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20251204041505.131891-4-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add fixed MCLK pin descriptions for all pins with such supported
function.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251204041505.131891-3-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add Qualcomm SM8650 CAMSS device tree node to the platform dtsi file,
the SM8650 CAMSS IP contains
* 6 x CSIPHY,
* 3 x CSID, 2 x CSID Lite,
* 3 x IFE, 2 x IFE Lite.
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20251204041505.131891-2-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add TLMM 120 for hdmi bridge enable.
In general this is the same setup as on the T14s. Since its using simple-bridge
and also is Lenovo, we also use the same realtek,rtd2171 compatible.
The real chip identity is not known yet. The bridge is wired with un-swapped
lanes, though.
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Link: https://lore.kernel.org/r/20260103-tb16-hdmi-v2-2-92b0930fa82e@oldschoolsolutions.biz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The usb_1_ss2 complex has 2 phys, usb_1_ss2_hsphy and usb_1_ss2_qmpphy. On this
laptop, they are used for different peripherals: The hsphy for the fingerprint
reader, the qmpphy to drive a hdmi bridge. The normal logical wiring for the dwc3
controller is to both phys. Delete the port@1 to the qmpphy.
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260103-tb16-hdmi-v2-1-92b0930fa82e@oldschoolsolutions.biz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The recent dt-bindings were updated for the missing RX/TX symbol clocks
for UFS.
Extend the existing list to make sure the DT contains the expected
amount of 'clocks' entries.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260103-ufs_symbol_clk-v2-3-51828cc76236@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Merge the addition of UFS PHY clocks to the Hamoa GCC binding through a
topic branch, to avoid DeviceTree validation warnings, and later allow
referencing the added clock constants.
Add some of the UFS symbol rx/tx muxes were not initially described.
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260103-ufs_symbol_clk-v2-1-51828cc76236@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add initial support for Qualcomm Kaanapali QRD board which enables
SD Card, UFS and booting to shell with UART console.
Written with help from Jishnu Prakash (added RPMhPD nodes), Nitin Rawat
(added ufs) and Manish Pandey (added SD Card).
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251215-knp-dts-v4-5-1541bebeb89f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add initial support for Qualcomm Kaanapali MTP board which enables PCIe,
SD Card, UFS and booting to shell with UART console.
Written with help from Jishnu Prakash (added RPMhPD nodes), Nitin Rawat
(added UFS), Manish Pandey (added SD Card) and Qiang Yu (added PCIe).
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251215-knp-dts-v4-4-1541bebeb89f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Physical client IDs are used on Glymur Inter Process Communication
Controller (IPCC), add a corresponding header file.
Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20251031-knp-ipcc-v3-3-62ffb4168dff@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On earlier platforms, Inter Process Communication Controller (IPCC) used
virtual client IDs and performed virtual-to-physical mapping in hardware,
so the IDs defined in dt-bindings/mailbox/qcom-ipcc.h are common across
platforms. Physical client IDs instead of virtual client IDs are used for
qcom new platforms like Kaanapali, which will be parsed by the devicetree
and passed to hardware to use Physical client IDs directly. Since physical
client IDs could vary across platforms, add a corresponding header file
for the Kaanapali platform.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20251031-knp-ipcc-v3-2-62ffb4168dff@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the Kaanapali SoC binding and the boards which use it.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251215-knp-dts-v4-1-1541bebeb89f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Introduce new binding for the Medion SPRCHRGD 14 S1 notebook with
X1E78100 SoC.
Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251204155212.230058-5-ggo@tuxedocomputers.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Introduce new binding for the TUXEDO Elite 14 Gen1 laptop with X1E78100
SoC.
Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20251204155212.230058-3-ggo@tuxedocomputers.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
TUXEDO Computers GmbH is a German supplier for computers.
Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20251204155212.230058-2-ggo@tuxedocomputers.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On X Elite, there is a crypto engine IP block similar to ones found on
SM8x50 platforms.
Describe the crypto engine and its BAM.
Tested-by: Wenjia Zhang <wenjia.zhang@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251211-crypto_dt_node_x1e80100-v6-1-03830ed53352@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The only core fix is in doc; all the others are in drivers, with the
biggest impacts in libsas being the rollback on error handling and in
ufs coming from a couple of error handling fixes, one causing a crash
if it's activated before scanning and the other fixing W-LUN
resumption.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iLgEABMIAGAWIQTnYEDbdso9F2cI+arnQslM7pishQUCaT4RWBsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMSwyLDImHGphbWVzLmJvdHRvbWxleUBoYW5zZW5wYXJ0bmVy
c2hpcC5jb20ACgkQ50LJTO6YrIVfSgEA23oY0kPjLLkNj4KAjLoWVPmZ/5efKw49
m6YUwfvzTS8BAIq4eFHVecwAM8FAe9NwuOKgO5d9u6epAy6wzBeP2jly
=cpHq
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The only core fix is in doc; all the others are in drivers, with the
biggest impacts in libsas being the rollback on error handling and in
ufs coming from a couple of error handling fixes, one causing a crash
if it's activated before scanning and the other fixing W-LUN
resumption"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: qcom: Fix confusing cleanup.h syntax
scsi: libsas: Add rollback handling when an error occurs
scsi: device_handler: Return error pointer in scsi_dh_attached_handler_name()
scsi: ufs: core: Fix a deadlock in the frequency scaling code
scsi: ufs: core: Fix an error handler crash
scsi: Revert "scsi: libsas: Fix exp-attached device scan after probe failure scanned in again after probe failed"
scsi: ufs: core: Fix RPMB link error by reversing Kconfig dependencies
scsi: qla4xxx: Use time conversion macros
scsi: qla2xxx: Enable/disable IRQD_NO_BALANCING during reset
scsi: ipr: Enable/disable IRQD_NO_BALANCING during reset
scsi: imm: Fix use-after-free bug caused by unfinished delayed work
scsi: target: sbp: Remove KMSG_COMPONENT macro
scsi: core: Correct documentation for scsi_device_quiesce()
scsi: mpi3mr: Prevent duplicate SAS/SATA device entries in channel 1
scsi: target: Reset t_task_cdb pointer in error case
scsi: ufs: core: Fix EH failure after W-LUN resume error
