Previously, the AMPDU state bit for a given TID was set before attempting
to start a BA session, which could result in the AMPDU state being marked
active even if ieee80211_start_tx_ba_session() failed. This patch changes
the logic to only set the AMPDU state bit after successfully starting a BA
session, ensuring proper synchronization between AMPDU state and BA session
status.
This fixes potential issues with aggregation state tracking and improves
compatibility with mac80211 BA session management.
Fixes: 44eb173bdd ("wifi: mt76: mt7925: add link handling in mt7925_txwi_free")
Cc: stable@vger.kernel.org
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/d5960fbced0beaf33c30203f7f8fb91d0899c87b.1764228973.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7992 and MT7990 support up to 19 interfaces per band and 32 in total.
Fixes: 8df63a4bbe ("wifi: mt76: mt7996: adjust interface num and wtbl size for mt7992")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20251215063728.3013365-7-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since some radar specifications maintained by the driver are incorrect
and are now also maintained by the firmware, offload the initialization
procedure to the firmware.
This fixes issues for radar detection rate testings.
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20251215063728.3013365-5-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When CSA countdown is going to start, carry UNI_BSS_INFO_BCN_BCC tag to
abort any CCA countdown.
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20251215063728.3013365-4-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
After channel switch, some tags of BSSINFO (rfch) and STAREC (bfer,
rate_ctrl) commands should also be updated. Otherwise, a BSS might not be
able to transmit with its peer using correct bandwidth.
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Link: https://patch.msgid.link/20251215063728.3013365-3-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
RDD_DET_MODE is a firmware command intended for testing and does not
pause TX after radar detection, so remove it from the normal flow;
instead, use the MAC_ENABLE_CTRL firmware command to resume TX after
the radar-triggered channel switch completes.
Fixes: 1529e335f9 ("wifi: mt76: mt7996: rework radar HWRDD idx")
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Link: https://patch.msgid.link/20251215063728.3013365-2-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use correct link_id to report CSA and CCA countdown events, and also
modify mt7996_channel_switch_beacon() to set beacon with the correct
link_id.
Co-developed-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Co-developed-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20251215063728.3013365-1-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- cfg80211/mac80211: S1G and UHR improvements
- hwsim: incumbent signal report test support
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEpeA8sTs3M8SN2hR410qiO8sPaAAFAmm7sb4ACgkQ10qiO8sP
aAD+iQ/+IYWmM1Z/Iu6eZZx/VPrc4Xnj/8UgbalyjetyLRYFNEvawFSdutqZ23uI
FO7vYbzGXMtAlt7fjmxVKMiN4aoX+rISRjG5cnH1qPpeVO8w9fnOZyqmNUFJFboN
ibpr4dqPIS2qZDKegvOa9JO+8KkkPerPWl608eOzXPxoZaZAMnXOhWuV4cWdvuTT
vEnL+Ma4ckkOV6QdBFazYaxAyTt3Mpqj5ULodixtKPMdgB3P+6mAVipp/icE5R1P
R/Vd7Fn+0r7wb/4+1S6DcCBvT6V6Ui94bIRF9DB5LGG/9iLPrGYRD52qQpetzXzA
Si238bs7qi/6t6Q5tfzK1LZVnzZXTUqcWGS6ba4JiMxrLTAK1AEmcLved6A48ywt
YH9zImLRBRMSANbH27BoWvijT5YZGMetH06cTdFmZ8MMGoYV7CWBxVOaIroH7WMx
exMnWEcX6PUVMtlIR4FTGwX/nalGbvnBtoMv9ei3NRb2Dkart8OFT6vIDfy6TBnD
BzAUE3pDAW3I7ukbLQGJ3mmanZpHtF/Xgfr5Y9EbZHPjtC08l7cwdd2zn0n3Q2qu
JGlzZiut6sJTfnRESbUvJ6fnCMdGARpQxq6p2At3njJW0sncvyV9WFKh4A+ReaDr
PQ24fgapG5PNEISevO+/FV1z2qZ0+IbHSmcH+BIoktBnPUBLZFo=
=cLVw
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2026-03-19' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Aside from various small improvements/cleanups, not much:
- cfg80211/mac80211: S1G and UHR improvements
- hwsim: incumbent signal report test support
* tag 'wireless-next-2026-03-19' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (31 commits)
qtnfmac: use alloc_netdev macro for single queue devices
wifi: libertas: don't kill URBs in interrupt context
wifi: libertas: use USB anchors for tracking in-flight URBs
wifi: nl80211: use int for band coming from netlink
wifi: rsi_91x_usb: do not pause rfkill polling when stopping mac80211
wifi: mac80211: fix STA link removal during link removal
wifi: nl80211: reject S1G/60G with HT chantype
wifi: ieee80211: fix definition of EHT-MCS 15 in MRU
wifi: cfg80211: check non-S1G width with S1G chandef
wifi: cfg80211: restrict cfg80211_chandef_create() to only HT-based bands
wifi: mac80211: don't use cfg80211_chandef_create() for default chandef
wifi: mac80211: Remove deleted sta links in ieee80211_ml_reconf_work()
wifi: b43: use register definitions in nphy_op_software_rfkill
wifi: cfg80211: split control freq check from chandef check
wifi: mac80211: always use full chanctx compatible check
wifi: mac80211: refactor chandef tracing macros
wifi: mac80211: validate HE 6 GHz operation when EHT is used
wifi: nl80211: split out UHR operation information
wifi: mwifiex: drop redundant device reference
wifi: rt2x00: drop redundant device reference
...
====================
Link: https://patch.msgid.link/20260319082439.79875-3-johannes@sipsolutions.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In network setup as below:
fastpath bypass
.----------------------------------------.
/ \
| IP - forwarding |
| / \ v
| / wan ...
| /
| |
| |
| brlan.1
| |
| +-------------------------------+
| | vlan 1 |
| | |
| | brlan (vlan-filtering) |
| | +---------------+
| | | DSA-SWITCH |
| | vlan 1 | |
| | to | |
| | untagged 1 vlan 1 |
| +---------------+---------------+
. / \
----->wlan1 lan0
. .
. ^
^ vlan 1 tagged packets
untagged packets
br_vlan_fill_forward_path_mode() sets DEV_PATH_BR_VLAN_UNTAG_HW when
filling in from brlan.1 towards wlan1. But it should be set to
DEV_PATH_BR_VLAN_UNTAG in this case. Using BR_VLFLAG_ADDED_BY_SWITCHDEV
is not correct. The dsa switchdev adds it as a foreign port.
The same problem for all foreignly added dsa vlans on the bridge.
First add the vlan, trying only native devices.
If this fails, we know this may be a vlan from a foreign device.
Use BR_VLFLAG_TAGGING_BY_SWITCHDEV to make sure DEV_PATH_BR_VLAN_UNTAG_HW
is set only when there if no foreign device involved.
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Link: https://patch.msgid.link/20260317110347.363875-1-ericwouds@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
* use bitops.h API when possible
* send netlink notification in case of client float event
* implement support for asymmetric peer IDs
* consolidate memory allocations during crypto operations
* add netlink notification check in selftests
* add FW mark check in selftest
-----BEGIN PGP SIGNATURE-----
iJEEABYIADkWIQQKU153ubb5unbkl6Gx/ZpNW1HNdwUCabkqjRsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMSwyLDIACgkQsf2aTVtRzXdlaAEA4fQA41/tbgsciMSf7aqT
lEAbZF/6DnsFZiTmuUfqPvQA/3+R0uiJlUTB3NGhhXXXikP4Yj61lWMDjw//lvYJ
74IG
=elM6
-----END PGP SIGNATURE-----
Merge tag 'ovpn-net-next-20260317' of https://github.com/OpenVPN/ovpn-net-next
Antonio Quartulli says:
====================
Included features:
* use bitops.h API when possible
* send netlink notification in case of client float event
* implement support for asymmetric peer IDs
* consolidate memory allocations during crypto operations
* add netlink notification check in selftests
* add FW mark check in selftest
* tag 'ovpn-net-next-20260317' of https://github.com/OpenVPN/ovpn-net-next:
ovpn: consolidate crypto allocations in one chunk
selftests: ovpn: add test for the FW mark feature
selftests: ovpn: check asymmetric peer-id
ovpn: add support for asymmetric peer IDs
selftests: ovpn: add notification parsing and matching
ovpn: notify userspace on client float event
ovpn: pktid: use bitops.h API
ovpn: use correct array size to parse nested attributes in ovpn_nl_key_swap_doit
selftests: ovpn: allow compiling ovpn-cli.c with mbedtls3
====================
Link: https://patch.msgid.link/20260317104023.192548-1-antonio@openvpn.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
chan.hdrlen is read once at channel registration by
ppp_register_net_channel(), and used to set the PPP net device's
hard_header_len. It was set to PPPOL2TP_L2TP_HDR_SIZE_NOSEQ (6), which
is 4 bytes too small if sequence numbers are later enabled via
setsockopt(PPPOL2TP_SO_SENDSEQ), causing unnecessary skb reallocations
on the TX path.
The setsockopt handler attempted to change netdev's hard_header_len by
updating chan.hdrlen, but the PPP layer never re-reads it after the
registration, so the update had no effect.
To avoid the unnecessary reallocations, set chan.hdrlen to
PPPOL2TP_L2TP_HDR_SIZE_SEQ (10) unconditionally at registration and
remove the ineffective update in the setsockopt callback.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://patch.msgid.link/20260317054141.524879-1-dqfext@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The test depends on accepting a packet that is larger than the
advertised window and that does not trigger an immediate ACK.
Previously, the test might still pass even if kernel behavior changed
unexpectedly. Add assertions verifying that the large packet was
accepted and no ACK was sent.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Link: https://patch.msgid.link/20260316-improve_tcp_neg_usable_wnd_test-v1-1-f16d5e365107@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Serialization for the TX path was enforced by calling
usb_kill_urb()/usb_kill_anchored_urbs(), to prevent transmission before
a previous URB was completed. usb_tx_block() can be called from
interrupt context (e.g. in the HCD giveback path), so we can't always
use it to kill in-flight URBs.
Prevent sleeping during interrupt context by checking the tx_submitted
anchor for existing URBs. We now return -EBUSY, to indicate there's
a pending request.
Reported-by: syzbot+74afbb6355826ffc2239@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=74afbb6355826ffc2239
Fixes: d66676e6ca ("wifi: libertas: fix WARNING in usb_tx_block")
Signed-off-by: Heitor Alves de Siqueira <halves@igalia.com>
Link: https://patch.msgid.link/20260313-libertas-usb-anchors-v1-2-915afbe988d7@igalia.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The libertas driver currently handles URB lifecycles manually, which
makes it non-trivial to check if specific URBs are pending or not. Add
anchors for TX/RX URBs, and use those to track in-flight requests.
Signed-off-by: Heitor Alves de Siqueira <halves@igalia.com>
Link: https://patch.msgid.link/20260313-libertas-usb-anchors-v1-1-915afbe988d7@igalia.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was pointed out before, but there are issues with just
removing the <0 check since enum representation isn't fixed,
nla_type() returns int but really can only return small
non-negative values, etc. Now newer versions of sparse are
also starting to warn on it. Just use int for the band var.
Link: https://patch.msgid.link/20260316123050.8c2d9f3426a0.I86acfa785982993fbffd148cc59049991bd6158f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Removing rsi_91x USB adapter could cause rtnetlink to lock up.
When rsi_mac80211_stop is called, wiphy_lock is locked. Call to
wiphy_rfkill_stop_polling would wait until the work queue has
finished, but because the work queue waits for wiphy_lock, that
would never happen.
Moving the call to rsi_disconnect avoids the lock up.
Signed-off-by: Ville Nummela <ville.nummela@kempower.com>
Link: https://patch.msgid.link/20260318081912.87744-1-ville.nummela@kempower.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_sta_free_link() only frees the link and doesn't
unhash it, so it can't be used here. Instead this needs
to use ieee80211_sta_remove_link(), which unhashes it. An
argument against it was that it also calls the driver and
that already happened, but calls to the driver removing a
link that's already removed are suppressed, so that's not
actually an issue. Use it to fix the hashtable.
Reported-and-tested-by: Jouni Malinen <j@w1.fi>
Fixes: 84674b03d8 ("wifi: mac80211: Remove deleted sta links in ieee80211_ml_reconf_work()")
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260318180622.9240067117e9.I45fb2b7f04d75e48d2f3e9c6650ef9f54a314f5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Haiyang Zhang says:
====================
add ethtool COALESCE_RX_CQE_FRAMES/NSECS and use it in MANA driver
Add two parameters for drivers supporting Rx CQE Coalescing.
ETHTOOL_A_COALESCE_RX_CQE_FRAMES:
Maximum number of frames that can be coalesced into a CQE or
writeback.
ETHTOOL_A_COALESCE_RX_CQE_NSECS:
Max time in nanoseconds after the first packet arrival in a
coalesced CQE or writeback to be sent.
Also implement it in MANA driver with the new parameter and
counters.
====================
Link: https://patch.msgid.link/20260317191826.1346111-1-haiyangz@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For RX CQEs with type CQE_RX_COALESCED_4, to measure the coalescing
efficiency, add counters to count how many contains 2, 3, 4 packets
respectively.
Also, add a counter for the error case of first packet with length == 0.
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://patch.msgid.link/20260317191826.1346111-4-haiyangz@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Our NIC can have up to 4 RX packets on 1 CQE. To support this feature,
check and process the type CQE_RX_COALESCED_4. The default setting is
disabled, to avoid possible regression on latency.
And, add ethtool handler to switch this feature. To turn it on, run:
ethtool -C <nic> rx-cqe-frames 4
To turn it off:
ethtool -C <nic> rx-cqe-frames 1
The rx-cqe-nsec is the time out value in nanoseconds after the first
packet arrival in a coalesced CQE to be sent. It's read-only for this
NIC.
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://patch.msgid.link/20260317191826.1346111-3-haiyangz@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add two parameters for drivers supporting Rx CQE coalescing /
descriptor writeback.
ETHTOOL_A_COALESCE_RX_CQE_FRAMES:
Maximum number of frames that can be coalesced into a CQE or
writeback.
ETHTOOL_A_COALESCE_RX_CQE_NSECS:
Max time in nanoseconds after the first packet arrival in a
coalesced CQE or writeback to be sent.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://patch.msgid.link/20260317191826.1346111-2-haiyangz@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Not used in mlx5e, clean it up.
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20260317104548.15697-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When running vmtest.sh inside a nested VM the running kernel may not be
installed on the filesystem at the standard /boot/ or /usr/lib/modules/
paths.
Previously, this would cause vng to fail with "does not exist" since it
could not find the kernel image. Instead, this patch uses --dry-run to
detect if the kernel is available. If not, then we fall back to the
kernel in the kernel source tree. If that fails, then we die.
This way runners, like NIPA, can use vng --run arch/x86/boot/bzImage to
setup an outer VM, and vmtest.sh will still do the right thing setting
up the inner VM.
Due to job control issues in vng, a workaround is used to prevent 'make
kselftest TARGETS=vsock' from hanging until test timeout. A PR has been
placed upstream to solve the issue in vng:
https://github.com/arighi/virtme-ng/pull/453
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260316-vsock-vmtest-autodetect-kernel-v2-1-5eec7b4831f8@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq Toukan says:
====================
mlx5-next updates 2026-03-17
The following pull-request contains common mlx5 updates
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Expose MLX5_UMR_ALIGN definition
{net/RDMA}/mlx5: Add LAG demux table API and vport demux rules
net/mlx5: Add VHCA RX flow destination support for FW steering
net/mlx5: LAG, replace mlx5_get_dev_index with LAG sequence number
net/mlx5: E-switch, modify peer miss rule index to vhca_id
net/mlx5: LAG, use xa_alloc to manage LAG device indices
net/mlx5: LAG, replace pf array with xarray
net/mlx5: Add silent mode set/query and VHCA RX IFC bits
net/mlx5: Add IFC bits for shared headroom pool PBMC support
net/mlx5: Expose TLP emulation capabilities
net/mlx5: Add TLP emulation device capabilities
====================
Link: https://patch.msgid.link/20260317075844.12066-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The calculation done by qed_calc_crc32c() is the standard
least-significant-bit-first CRC-32C except it uses
most-significant-bit-first order for the actual CRC variable. That is
equivalent to bit-reflecting the input and output CRC. Replace it with
equivalent calls to the corresponding library functions.
Tested with a simple userspace program which tested that the old and new
implementations of qed_mcast_bin_from_mac() produce the same outputs.
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Link: https://patch.msgid.link/20260316221453.66078-1-ebiggers@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq Toukan says:
====================
net/mlx5: Support PTM on ARM architecture
This series by Carolina refactors mlx5 crosststamp initialization and
enables cross-timestamp support on ARM.
====================
Link: https://patch.msgid.link/20260316133607.8738-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend cross-timestamp support for ARM systems that implement the ARM
architected timer.
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260316133607.8738-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the crosststamp registration logic into a dedicated helper,
mlx5_init_crosststamp().
This prepares the code for a follow-up patch around PTM handling.
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260316133607.8738-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bartosz Golaszewski says:
====================
net: mdio-gpio: remove unneeded headers
This removes linux/mdio-gpio.h and linux/platform_data/mdio-gpio.h as
they are not needed due to the symbols either being used by the
mdio-gpio module alone or not used at all.
====================
Link: https://patch.msgid.link/20260316-gpio-mdio-hdr-cleanup-v1-0-2df696f74728@oss.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The three defines from the linux/mdio-gpio.h header are only used in the
mdio-gpio module. There's no reason to have them in a public header.
Move them into the driver and remove mdio-gpio.h.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260316-gpio-mdio-hdr-cleanup-v1-1-2df696f74728@oss.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit says:
====================
remove Kconfig sysmbol MDIO_BUS
MDIO-based regmap is the last user of config symbol MDIO_BUS.
MDIO access needs a MII bus, which requires PHYLIB for the provider part.
Therefore make REGMAP_MDIO depend on PHYLIB, what allows to remove
config symbol MDIO_BUS.
====================
Link: https://patch.msgid.link/bc63cf87-3dba-4ab6-9c84-caa7357c3273@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After usage of config symbol MDIO_BUS has been removed from REGMAP_MIO
as last user, the symbol can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/9cdf83e9-470d-45da-8efe-ace0decf0204@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MDIO-based regmap is the last user of config symbol MDIO_BUS.
MDIO access needs a MII bus, which requires PHYLIB for the provider part.
Therefore make REGMAP_MDIO depend on PHYLIB, what allows to remove
config symbol MDIO_BUS in a follow-up patch.
Note: After c5a219395b ("regmap: Move selecting for REGMAP_MDIO and
REGMAP_IRQ") switching to "depends on" should be fine, w/o risk
of a circular dependency.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/a21a3b3e-272e-4c61-986e-48a2cb3421d9@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for reporting HDS (Header-Data Split) threshold via
ethtool. When applicable, mlx5 hardware splits packets of all sizes with
no configurable threshold, so report both hds-thresh and hds-thresh-max
as 0 (i.e. always split regardless of size).
Signed-off-by: Nimrod Oren <noren@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20260317104934.16124-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geert Uytterhoeven says:
====================
dt-bindings: net: micrel: Fix KSZ8041RNLI dtbs_check warnings
"make dtbs_check" reports several warnings due to some KSZ8041RNLI PHY
nodes having the "micrel,led-mode" property, while the DT bindings
prohibit this.
Apparently the DT bindings are incorrect, so this patch series fixes
that, after a customary cleanup.
====================
Link: https://patch.msgid.link/cover.1773734298.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Micrel KSZ8041RNLI supports LED mode, just like KSZ8041.
This fixes (a.o.) the following "make dtbs_check" warning:
arch/arm/boot/dts/renesas/r8a7791-koelsch.dtb: ethernet-phy@1 (ethernet-phy-id0022.1537): False schema does not allow 1
from schema $id: http://devicetree.org/schemas/net/micrel.yaml
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stefan Eichenberger <eichest@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/efad6c7e024b3a9aa2882db65909ee5bbbcbdc45.1773734298.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Donald points out that the current naive implementation using dicts
breaks if policy is recursive (child nest uses policy idx already
used by its parent).
Lean more into the NlPolicy class. This lets us "render" the policy
on demand, when user accesses it. If someone wants to do an infinite
walk that's on them :) Show policy info as attributes of the class
and use dict format to descend into sub-policies for extra neatness.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20260313232047.2068518-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King says:
====================
net: stmmac: clean up descriptor handling part 1
Part 1 of cleaning up the stmmac descriptor handling. Rearrange the
struct stmmac_tx_info to pack better, and introduce helpers for
duplicated code handing the transmit and receive descriptors. Remove
unnecessary struct members that are only transitorily used.
====================
Link: https://patch.msgid.link/abUtGH9KB03PH5Ne@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We use a lot of ->queue_index where we already have the queue / channel
index (which are actually the same index), which has been used to get
the queue struct. Since queue and queue_index are identical in
priv->(tx|rx)_queue[queue]->queue_index there is no point using the
queue_index where we already have queue.
Use queue rather than queue_index.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w1LWy-0000000DGT8-2Hoc@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is only one place where tx_q->tx_tail_addr is used - the new
stmmac_set_queue_tx_tail_ptr(). Make this a local variable and remove
it from struct stmmac_tx_queue.
This commit does not change the semantics - the hardware relies upon
the descriptor ring not crossing a 4GiB boundary as the high address
bits are programmed into a separate register via stmmac_init_tx_chan().
Hence, truncating the DMA address to 32-bit is fine as the register it
will be programmed into is 32-bit, and the high bits are handled
elsewhere.
Also change the type of desc_size to size_t, as this variable is
initialised from sizeof().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w1LWt-0000000DGT2-1oeO@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Setting the queue transmit tail pointer follows a common pattern:
calculate the DMA address, and then call stmmac_set_tx_tail_ptr().
The only difference between all the call sites is the index used.
Factor this out into a static function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w1LWo-0000000DGSw-1MCe@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide a helper to get the hardware transmit descriptor that takes
account of whether extended format and TBS are being used, returning
the base struct dma_desc pointer. This avoids multiple instances where
these tests are open coded.
We need to update dwmac4_display_ring() to cope the passed head
pointer always pointing at the struct dma_desc by using
dma_desc_to_edesc() to convert it to struct dma_edesc. This is the
only stmmac_display_ring() implementation that this affects.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w1LWe-0000000DGSj-0KtE@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are three sites that configure the hardware for the receive
buffer size using the same logic to determine the buffer size.
Add a helper so there is only one copy of this code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w1LWT-0000000DGSX-3fxc@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Two out of the three sites that set the receive buffer size (via
stmmac_set_dma_bfsize()) check for rx_q->xsk_pool &&
rx_q->buf_alloc_num. One uses just rx_q->xsk_pool.
Discussing with Yoong Siang Song, the conclusion is that
stmmac_dma_operation_mode() is missing the rx_q->buf_alloc_num
check. Add this check.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w1LWO-0000000DGSR-3CaB@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
