The 4430 and 4460 version of PandaBoard mostly the same with
exception at least in audio setup.
Use the omap4-panda.dts file as a base and only override the differences
between the revisions.
For audio it is the name of the sound card and the routing information.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
PandaBoard uses twl6040 connected via McPDM for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4 SDP the audio setup includes the twl6040 codec and digital
microphones.
Since OMAP4 SDP is a reference board it has all possible audio interfaces
connected. This information is passed via the ti,audio-routing
property.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The twl6040 provides the audio and vibra support on OMAP4 SDP boards.
It is connected to i2c1 bus with 0x4b address.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DMIC IP is used to connect up to 6 digital microphones directly to OMAP.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McPDM is used on OMAP4 based boards to communicate with an external audio
codec (twl6040).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make sure we prepare/unprepare the clock for the ST U300
I2C driver as is required by the clk API especially if you
use common clock.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The sys_nirq2 is used for twl6040, make sure the pin is configured
correctly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sys_nirq2 is used for twl6040, make sure the pin is configured
correctly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This feature has been around for over 5 years now, and has no
CONFIG_EXPERIMENTAL dependency anymore, so remove the '(EXPERIMENTAL)'
tag from the help text as well.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Link: http://lkml.kernel.org/r/1341583705.4655.18.camel@amber.site
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Indirect extent block is not accounted in i_blocks during allocation
thus we should not decrement i_blocks when we are freeing such block
during truncation.
Reported-by: Steve Nickel <snickel58@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Our emulation should be complete enough that we can emulate guests
while they are in big real mode, or in a mode transition that is not
virtualizable without unrestricted guest support.
Signed-off-by: Avi Kivity <avi@redhat.com>
Guest software doesn't actually depend on it, but vmx will refuse us
entry if we don't. Set the bit in both the cached segment and memory,
just to be nice.
Signed-off-by: Avi Kivity <avi@redhat.com>
Opcode C8.
Only ENTER with lexical nesting depth 0 is implemented, since others are
very rare. We'll fail emulation if nonzero lexical depth is used so data
is not corrupted.
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit 2adb5ad9fe removed ByteOp from MOVZX/MOVSX, replacing them by
SrcMem8, but neglected to fix the dependency in the emulation code
on ByteOp. This caused the instruction not to have any effect in
some circumstances.
Fix by replacing the check for ByteOp with the equivalent src.op_bytes == 1.
Signed-off-by: Avi Kivity <avi@redhat.com>
If we return early from an invalid guest state emulation loop, make
sure we return to it later if the guest state is still invalid.
Signed-off-by: Avi Kivity <avi@redhat.com>
Checking EFLAGS.IF is incorrect as we might be in interrupt shadow. If
that is the case, the main loop will notice that and not inject the interrupt,
causing an endless loop.
Fix by using vmx_interrupt_allowed() to check if we can inject an interrupt
instead.
Signed-off-by: Avi Kivity <avi@redhat.com>
We correctly default to SS when BP is used as a base in 16-bit address mode,
but we don't do that for 32-bit mode.
Fix by adjusting the default to SS when either ESP or EBP is used as the base
register.
Signed-off-by: Avi Kivity <avi@redhat.com>
memop is not initialized; this can lead to a two-byte operation
following a 4-byte operation to see garbage values. Usually
truncation fixes things fot us later on, but at least in one case
(call abs) it doesn't.
Fix by moving memop to the auto-initialized field area.
Signed-off-by: Avi Kivity <avi@redhat.com>
Otherwise, if the guest ends up looping, we never exit the srcu critical
section, which causes synchronize_srcu() to hang.
Signed-off-by: Avi Kivity <avi@redhat.com>
Some userspace (e.g. QEMU 1.1) munge the d and g bits of segment
descriptors, causing us not to recognize them as unusable segments
with emulate_invalid_guest_state=1. Relax the check by testing for
segment not present (a non-present segment cannot be usable).
Signed-off-by: Avi Kivity <avi@redhat.com>
The operand size for these instructions is 8 bytes in long mode, even without
a REX prefix. Set it explicitly.
Triggered while booting Linux with emulate_invalid_guest_state=1.
Signed-off-by: Avi Kivity <avi@redhat.com>
Opcode 0F A2.
Used by Linux during the mode change trampoline while in a state that is
not virtualizable on vmx without unrestricted_guest, so we need to emulate
it is emulate_invalid_guest_state=1.
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of getting an exact leaf, follow the spec and fall back to the last
main leaf instead. This lets us easily emulate the cpuid instruction in the
emulator.
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduce kvm_cpuid() to perform the leaf limit check and calculate
register values, and let kvm_emulate_cpuid() just handle reading and
writing the registers from/to the vcpu. This allows us to reuse
kvm_cpuid() in a context where directly reading and writing registers
is not desired.
Signed-off-by: Avi Kivity <avi@redhat.com>
In protected mode, the CPL is defined as the lower two bits of CS, as set by
the last far jump. But during the transition to protected mode, there is no
last far jump, so we need to return zero (the inherited real mode CPL).
Fix by reading CPL from the cache during the transition. This isn't 100%
correct since we don't set the CPL cache on a far jump, but since protected
mode transition will always jump to a segment with RPL=0, it will always
work.
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently the MMU's ->new_cr3() callback does nothing when guest paging
is disabled or when two-dimentional paging (e.g. EPT on Intel) is active.
This means that an emulated write to cr3 can be lost; kvm_set_cr3() will
write vcpu-arch.cr3, but the GUEST_CR3 field in the VMCS will retain its
old value and this is what the guest sees.
This bug did not have any effect until now because:
- with unrestricted guest, or with svm, we never emulate a mov cr3 instruction
- without unrestricted guest, and with paging enabled, we also never emulate a
mov cr3 instruction
- without unrestricted guest, but with paging disabled, the guest's cr3 is
ignored until the guest enables paging; at this point the value from arch.cr3
is loaded correctly my the mov cr0 instruction which turns on paging
However, the patchset that enables big real mode causes us to emulate mov cr3
instructions in protected mode sometimes (when guest state is not virtualizable
by vmx); this mov cr3 is effectively ignored and will crash the guest.
The fix is to make nonpaging_new_cr3() call mmu_free_roots() to force a cr3
reload. This is awkward because now all the new_cr3 callbacks to the same
thing, and because mmu_free_roots() is somewhat of an overkill; but fixing
that is more complicated and will be done after this minimal fix.
Observed in the Window XP 32-bit installer while bringing up secondary vcpus.
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch mutes the false positive compiler warning:
drivers/i2c/busses/i2c-mxs.c: In function 'mxs_i2c_xfer_msg':
drivers/i2c/busses/i2c-mxs.c:206:8: warning: 'data' may be used uninitialized in this function [-Wuninitialized]
drivers/i2c/busses/i2c-mxs.c:196:6: note: 'data' was declared here
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The core and irq Arizona parts should be boolean as they depend on non
exported symbols.
This fixes the following build errors:
ERROR: "wm5102_aod" [drivers/mfd/arizona-irq.ko] undefined!
ERROR: "wm5102_irq" [drivers/mfd/arizona-irq.ko] undefined!
ERROR: "irq_set_chip_and_handler_name" [drivers/mfd/arizona-irq.ko] undefined!
ERROR: "wm5102_patch" [drivers/mfd/arizona-core.ko] undefined!
ERROR: "arizona_irq_init" [drivers/mfd/arizona-core.ko] undefined!
ERROR: "arizona_irq_exit" [drivers/mfd/arizona-core.ko] undefined!
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
CP_INTC code in entry-macro.S code reads SECR1n register to see if
an interrupt was indeed pending. This register is actually marked as
write-only in the OMAP-L138 TRM. Moreover, the code just checks to see
the entire register is non-zero and does not check a specific interrupt
number.
Fix this to use interrupt pending bit in GIPR register for this purpose.
GIPR register is already being read to know the highest priority interrupt
pending.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
When we are mounting filesystem, we can load one partition table before
finding out that we cannot complete processing of logical volume descriptor
and trying the reserve descriptor. Free the table properly before trying
the reserve descriptor.
Signed-off-by: Jan Kara <jack@suse.cz>
Cleanup the confused goto label, since the big lock has been removed.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The variable "offset" is not needed. Remove it.
Signed-off-by: Ashish Sangwan <ashish.sangwan2@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The UDF file-system does not need the 's_dirt' superblock flag because it does
not define the 'write_super()' method. This flag was set to 1 in few places and
set to 0 in '->sync_fs()' and was basically useless. Stop using it because it
is on its way out.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
If ext3_setup_super() fails i.e. due to a too-high revision,
the error is logged in dmesg but the fs is not mounted RO as
indicated.
Tested by:
[164152.114551] EXT3-fs (sdb6): error: revision level too high, forcing read-only mode
/dev/sdb6 /mnt/test2 ext3 rw,seclabel,relatime,errors=continue,user_xattr,acl,barrier=1,data=ordered 0 0
^^
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Andreas Dilger <adilger@whamcloud.com>
Signed-off-by: Jan Kara <jack@suse.cz>
checkpatch.pl warns:
"WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>"
Below patch fixes it.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>