The call of usb_set_interface() and a delay are superfluous when the
device has been already disconnected. Add a disconnection check
before doing it.
Link: https://patch.msgid.link/20240808091522.31415-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current MIDI input flush on HDSP and HDSPM drivers relies on the
hardware reporting the right value. If the hardware doesn't give the
proper value but returns -1, it may be stuck at an infinite loop.
Add a counter and break if the loop is unexpectedly too long.
Link: https://patch.msgid.link/20240808091513.31380-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASIHPI driver stores some values in the static array upon a response
from the driver, and its index depends on the firmware. We shouldn't
trust it blindly.
This patch adds a sanity check of the array index to fit in the array
size.
Link: https://patch.msgid.link/20240808091454.30846-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At the code refactoring of USB-audio quirk handling, I assumed that
the quirk entries of Stanton ScratchAmp devices were only about the
device name, and moved them completely into the rename table.
But it seems that the device requires the quirk entry so that it's
probed by the driver itself.
This re-adds back the quirk entries of ScratchAmp, but in a
minimalistic manner.
Fixes: 5436f59bc5 ("ALSA: usb-audio: Move device rename and profile quirks to an internal table")
Link: https://patch.msgid.link/20240808081803.22300-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
Move the conflicting declaration to the end of the structure. Notice
that `struct snd_sof_pcm` ends in a flexible-array member through
`struct snd_soc_tplg_pcm` -> `struct snd_soc_tplg_private`.
Whith this, fix the following warnings:
sound/soc/sof/sof-audio.h:350:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
./include/trace/events/../../../sound/soc/sof/sof-audio.h:350:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
sound/soc/amd/../sof/amd/../sof-audio.h:350:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
sound/soc/sof/amd/../sof-audio.h:350:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
sound/soc/sof/intel/../sof-audio.h:350:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
sound/soc/sof/mediatek/mt8186/../../sof-audio.h:350:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
sound/soc/sof/mediatek/mt8195/../../sof-audio.h:350:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/ZrDvt6eyeFyajq6l@cute
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ZSC Control register programming sequence for ACP D0 and D3 state
transitions for ACP7.0 onwards. This will allow ACP to enter low power
state when ACP enters D3 state. When ACP enters D0 State, ZSC control
should be disabled.
Tested-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://patch.msgid.link/20240807085154.1987681-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As module device table added for AMD SoundWire machine driver MODULE_ALIAS
is not required. Remove MODULE_ALIAS for AMD SoundWire machine driver.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240807050846.1616725-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that regmap_read_bypassed() has been added to the kernel it is
preferable to wake the device with a read rather than a write as the
utility function can be called at a time before the device has been
identified.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Link: https://patch.msgid.link/20240807142715.47077-1-simont@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Exynos7885 SoC has a DWC3 USB Controller with Exynos USB PHY which in
theory supports USB3 SuperSpeed, but is only used as USB2 in all known
devices.
These, of course, need some clocks.
Add indices for these clocks.
Signed-off-by: David Virag <virag.david003@gmail.com>
Link: https://lore.kernel.org/r/20240806121157.479212-4-virag.david003@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The numbering in Exynos7885's FSYS CMU bindings has 4 duplicated by
accident, with the rest of the bindings continuing with 5.
Fix this by moving CLK_MOUT_FSYS_USB30DRD_USER to the end as 11.
Since CLK_MOUT_FSYS_USB30DRD_USER is not used in any device tree as of
now, and there are no other clocks affected (maybe apart from
CLK_MOUT_FSYS_MMC_SDIO_USER which the number was shared with, also not
used in a device tree), this is the least impactful way to solve this
problem.
Fixes: cd268e309c ("dt-bindings: clock: Add bindings for Exynos7885 CMU_FSYS")
Cc: stable@vger.kernel.org
Signed-off-by: David Virag <virag.david003@gmail.com>
Link: https://lore.kernel.org/r/20240806121157.479212-2-virag.david003@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Building with Sparse enabled prints this warning for cpu_to_le16()
calls:
warning: incorrect type in assignment (different base types)
expected unsigned short [usertype]
got restricted __le16 [usertype]
And this warning for le16_to_cpu() calls:
warning: cast to restricted __le16
Declare the target buffer as __le16 to fix both warnings.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Acked-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240716161725.41408-2-jose.exposito89@gmail.com
Bindings expect the LED node names to follow certain pattern, see
dtbs_check warnings:
at91sam9g15ek.dtb: leds: 'pb18', 'pd21' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Link: https://lore.kernel.org/r/20240701164952.577277-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
These properties are common for all i2c subnodes. Allows to add i2c device
nodes (like an rtc for example) in other .dts files including
sam9x60.dtsi without requiring to repeat these properties for each i2c
device again and again.
Found on a custom board after adding this in .dts:
&flx5 {
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
i2c5: i2c@600 {
pinctrl-0 = <&pinctrl_flx5_default>;
status = "okay";
pcf8523: rtc@68 {
compatible = "nxp,pcf8523";
reg = <0x68>;
};
};
};
… which created a warning like this:
[…]:236.4-17: Warning (reg_format): /ahb/apb/flexcom@f0004000/i2c@600/rtc@68:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
[…]: Warning (pci_device_reg): Failed prerequisite 'reg_format'
[…]: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
[…]: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
[…]/linux-6.6.25/arch/arm/boot/dts/microchip/sam9x60.dtsi:283.19-299.7: Warning (i2c_bus_bridge): /ahb/apb/flexcom@f0004000/i2c@600: incorrect #address-cells for I2C bus also defined at […]:228.16-238.4
[…]/linux-6.6.25/arch/arm/boot/dts/microchip/sam9x60.dtsi:283.19-299.7: Warning (i2c_bus_bridge): /ahb/apb/flexcom@f0004000/i2c@600: incorrect #size-cells for I2C bus also defined at […]:228.16-238.4
[…]: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
[…]: Warning (i2c_bus_reg): Failed prerequisite 'i2c_bus_bridge'
[…]: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
[…]:234.19-237.5: Warning (avoid_default_addr_size): /ahb/apb/flexcom@f0004000/i2c@600/rtc@68: Relying on default #address-cells value
[…]:234.19-237.5: Warning (avoid_default_addr_size): /ahb/apb/flexcom@f0004000/i2c@600/rtc@68: Relying on default #size-cells value
[…]: Warning (avoid_unnecessary_addr_size): Failed prerequisite 'avoid_default_addr_size'
[…]: Warning (unique_unit_address): Failed prerequisite 'avoid_default_addr_size'
This probably should have been done with commit 84f23f3284 ("ARM: dts:
at91: sam9x60: move flexcom definitions") already, where those
address-cells and size-cells properties were left in the board .dts
files instead of moving them to the dtsi.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20240528153109.439407-1-ada@thorsis.com
[claudiu.beznea: adjusted commit message as the properties are not
required anymore]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Contrary to the vendor-kernel the pmu-io-domains are not enabled by
default. This resulted in the value not being set according to the
regulator, which in turn made the gmac0 interface that is connected
to the vccio4 supply inoperable.
Fixes: 64b7f16fb3 ("arm64: dts: rockchip: add 2 pmu_io_domain supplies for Qnap-TS433")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240805162052.3345768-1-heiko@sntech.de
Now that all users of snd_print*() are gone, let's drop the functions
completely. This also makes CONFIG_SND_VERBOSE_PRINTK redundant, and
it's dropped, too.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-55-tiwai@suse.de
The legacy snd_print*() helpers will be dropped now. Clean up the
corresponding documentation, too.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-54-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
The debug prints with a special macro snd_printddd() are replaced with
the conditional pr_debug(). Unfortunately dev_dbg() can't be applied
well due to the lack of the reference to the device pointer.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-53-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-52-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-51-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-50-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-49-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-48-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Some superfluous debug prints are dropped, and some ambiguous messages
are slightly rephrased. The sk.dev pointer is set properly for
allowing to call dev_*() functions, too.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-45-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Some functions are changed to receive snd_card object for calling
dev_*() functions, too.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-44-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-43-tiwai@suse.de
Replace an open-coded printk warning with dev_warn() for code
simplicity and consistency.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-42-tiwai@suse.de
Use pr_debug() instead of open-coded printk().
Also drop a few snd_printdd() calls that can be better done via
ftrace.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-40-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-39-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
The device pointer is stored in struct cmdif for calling dev_*()
functions.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-38-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-37-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-36-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
The device pointer is stored in struct soundscape for calling
dev_*().
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-35-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Some functions are changed to receive a device pointer to be passed to
dev_*() calls.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-34-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Some functions are changed to receive snd_card pointer for referring
to the device pointer for dev_*() calls, too.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-31-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
The card pointer is stored in struct snd_opti9xx and snd_miro to be
referred for dev_*() calls.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-30-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
The card pointer is stored in struct snd_opl3sa2 to be referred for
dev_*() calls.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-29-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-28-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
Some commented-out debug prints and dead code are dropped as well.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-27-tiwai@suse.de
Use the standard print API with dev_*() instead of the old house-baked
one. It gives better information and allows dynamically control of
debug prints.
For referring to the device, introduce snd_card pointer to struct
snd_es18xx.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807133452.9424-26-tiwai@suse.de
