If the OTP is empty, the NVM_GET_INFO command returns
with flags' bit(0) on. This means the FW returns the
default values for working with. This is allowed, so
use this returned data.
Fixes: e9e1ba3dbf ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The return status check of iwl_pcie_gen2_build_amsdu
was buggy. Fix it.
Fixes: 6ffe5de35b ("iwlwifi: pcie: add AMSDU to gen2")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While waiting for queues to empty,
If txq_id == IWL_MVM_INVALID_QUEUE for all txq_ids,
ret is used uninitialized.
Found by Klocwork.
Fixes: d6d517b773 ("iwlwifi: add wait for tx queue empty")
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FIFO numbering is different in A000 devices. This
means that we routed BE packets to BK FIFO. Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We currently support 3 different versions of the beacon template
command and the code does some tricks in order to reuse what is
possible across these versions. But it is a bit complicated to read
and soon there will be one more variation that the driver needs
implement, which would complicate it even further.
Refactor the way we send beacon template commands, which increases the
code size a bit, but makes it much easier to read.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Those constants have been unused for quite some time now.
Signed-off-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Convention has it to byte-swap the constant instead of the variable
when doing bit checks. This also generates better code when the swap
is actually needed, since the constant can be swapped at compile-time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are two workarounds because RSS is currently broken on A000
devices due to firmware issues, but checking for the new TX API
doesn't really make sense. Check the hardware family instead of
the new TX API - there's nothing better to check since it's just
a temporary workaround.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This may need to be refined later, but for now using this,
even with the TODO, is better than checking "has new TX API".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Apart from DVM, all firmware uses the same base API, and there's
code outside iwlmvm that needs to interact with it. Reflect this
in the source better and reorganize the firmware API to a new
fw/api/ directory.
While at it, split the already pretty large fw-api.h file into a
number of smaller files, going from almost 3k lines in there to
a maximum number of lines less than 1k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Track the current firmware image in the common code instead
of in the opmode so that later patches can access it there
in a common way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactor the shared memory command parsing into common code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactor the paging code from mvm to be used by different opmodes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add two PCI IDs for the 9160 series.
Add five PCI IDs for the 9260 series.
Add one PCI IDs for the 9270 series.
Add seven PCI IDs for the 9460 series.
Add five PCI IDs for the 9560 series.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver has gained a compile-time dependency that we should
express in Kconfig to avoid this link error:
drivers/hid/wacom_sys.o: In function `wacom_parse_and_register':
wacom_sys.c:(.text+0x2eec): undefined reference to `usb_hid_driver'
Fixes: 09dc28acae ("HID: wacom: Improve generic name generation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Set the STA_FLG_RTS_MIMO_PROT bit in station_flags_msk of the add sta
command, so that when smps mode changes, the FW will know about it.
In particular, in AP mode, clients are added upon receival of an auth
request, at which point there's no knowledge of the client's smps mode.
When the assoc request arrives, the add_sta command is resent to modify
the station parameters. At this point the driver knows the smps mode,
but since the corresponding bit in the mask is not set, the fw doesn't
update this field so there's no rts protection for mimo.
Fixes: 5bc5aaad40 ("iwlwifi: mvm: set up initial SMPS/NSS station info")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
for_each_obj_in_state is about to be removed, so convert
to the new iterator macros.
Just like in omap, use crtc_state->active instead of
crtc_state->enable when waiting for completion.
Changes since v1:
- Fix compilation.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Rob Herring <robh@kernel.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170719143920.25685-6-maarten.lankhorst@linux.intel.com
Use the new atomic iterator macros, the old ones are about to be
removed. With the new macros, it's more easy to get old and new state so
get them from the macros instead of from obj->state.
Changes since v1:
- Don't mix up old and new state. (danvet)
- Rebase on top of interruptible swap_state changes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20170719143920.25685-7-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new iterator macro and look for crtc_state->active instead of
enable, only crtc_state->active implies that vblanks will happen.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170719143920.25685-5-maarten.lankhorst@linux.intel.com
C step NICs should use the latest FW (currently B step).
Correct the condition to make C step NICs advanced its default FW name
to the latest one.
Also rename _next_ to b_or_c to avoid confusion.
Fixes: 5da083d192 ("iwlwifi: add support for 9000 HW B-step NICs")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
for_each_obj_in_state is about to be removed, so use the correct new
iterator macro.
I renamed the variable to 'unused', but forgot to convert
drm_atomic_helper_wait_for_flip_done to the new iterator macro,
so make it work this time.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Link: https://patchwork.freedesktop.org/patch/msgid/20170719143920.25685-2-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Statistics should be collected according to the actual rate a
frame/aggregation was transmitted and not according to the initial rate
from the last LQ command (these rates are different if the frames were
retransmitted at a lower rate from the rate scale table).
This is needed to remove throughput degradation.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The bit was set only if there was at least one reclaimed frame in an
aggregation. It's important to set it also in the case that the whole
A-MPDU was lost, otherwise rate scaling statistics will not be
updated correctly. Thus, set it always in ba notification handler.
This fixes a throughput degradation of about 20% in certain scenarios
with multiple streams on 11ac.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the function gpio_set_wake_irq(), port->irq_high is only checked for
zero. As platform_get_irq() returns a value less then zero if no interrupt
was found, any gpio >= 16 was handled like an irq_high interrupt was
available. On iMX27 for example no high interrupt is available. This lead
to the problem that only some gpios (the lower 16) were useable as wake
sources.
Signed-off-by: Philipp Rosenberger <p.rosenberger@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When we create a regulatory domain out of an MCC
notification, we need to make sure that all the channels
in the rule have the exact same properties.
The current code mixes channel 36 and 40 although 36 can be
a control channel with HT40+ (36, 40) whereas 40 can't be
a control channel with HT40+ since (40, 44) is invalid.
Because of that, cfg80211 would allow to connect in 40MHz
to APs that are configured to channel 40 HT40+ and that made
our firmware assert.
Fix this by checking the bandwidth flags before taking the
decision if the rule should be split.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299 partly.
Fixes: af45a9003f ("iwlwifi: create regdomain from mcc_update_cmd response")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware now adds a new DWORD for the MLME offload's
capability even on firmware versions that don't support
it.
Add the TLV bit to avoid getting the print:
capa flags index 3 larger than supported by driver.
This fixes the bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=196195
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This driver calls irq_domain_hierarchy() and irq_chip_*_parent().
They are available only when CONFIG_IRQ_DOMAIN_HIERARCHY is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drivers that need IRQ_DOMAIN_HIERARCHY should "select" it, but
drivers/pinctrl/stm32/Kconfig is the only exception that uses
"depends on" syntax. This prevents GPIO drivers from select'ing
IRQ_DOMAIN_HIERARCHY.
For example, if I add "select IRQ_DOMAIN_HIERARCHY" to GPIO_XGENE_SB,
I get the following recursive dependency error.
drivers/gpio/Kconfig:13:error: recursive dependency detected!
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpio/Kconfig:13: symbol GPIOLIB is selected by PINCTRL_STM32
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pinctrl/stm32/Kconfig:3: symbol PINCTRL_STM32 is selected by PINCTRL_STM32F429
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pinctrl/stm32/Kconfig:11: symbol PINCTRL_STM32F429 depends on IRQ_DOMAIN_HIERARCHY
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
kernel/irq/Kconfig:67: symbol IRQ_DOMAIN_HIERARCHY is selected by GPIO_XGENE_SB
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpio/Kconfig:502: symbol GPIO_XGENE_SB depends on GPIOLIB
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When we enabled TCP checksum offload, we need to tell the
firmware where the IP header starts. If we have an IV, then
we need to adapt that value since the IV is placed before
the SNAP header. This is true only for cases where the
driver adds the IV, not the WEP case in which the IV is
added by the firmware itself.
On A000 devices series, the IV is always added by the
device.
Fix this.
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull networking fixes from David Miller:
1) Handle notifier registry failures properly in tun/tap driver, from
Tonghao Zhang.
2) Fix bpf verifier handling of subtraction bounds and add a testcase
for this, from Edward Cree.
3) Increase reset timeout in ftgmac100 driver, from Ben Herrenschmidt.
4) Fix use after free in prd_retire_rx_blk_timer_exired() in AF_PACKET,
from Cong Wang.
5) Fix SElinux regression due to recent UDP optimizations, from Paolo
Abeni.
6) We accidently increment IPSTATS_MIB_FRAGFAILS in the ipv6 code
paths, fix from Stefano Brivio.
7) Fix some mem leaks in dccp, from Xin Long.
8) Adjust MDIO_BUS kconfig deps to avoid build errors, from Arnd
Bergmann.
9) Mac address length check and buffer size fixes from Cong Wang.
10) Don't leak sockets in ipv6 udp early demux, from Paolo Abeni.
11) Fix return value when copy_from_user() fails in
bpf_prog_get_info_by_fd(), from Daniel Borkmann.
12) Handle PHY_HALTED properly in phy library state machine, from
Florian Fainelli.
13) Fix OOPS in fib_sync_down_dev(), from Ido Schimmel.
14) Fix truesize calculation in virtio_net which led to performance
regressions, from Michael S Tsirkin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
samples/bpf: fix bpf tunnel cleanup
udp6: fix jumbogram reception
ppp: Fix a scheduling-while-atomic bug in del_chan
Revert "net: bcmgenet: Remove init parameter from bcmgenet_mii_config"
virtio_net: fix truesize for mergeable buffers
mv643xx_eth: fix of_irq_to_resource() error check
MAINTAINERS: Add more files to the PHY LIBRARY section
ipv4: fib: Fix NULL pointer deref during fib_sync_down_dev()
net: phy: Correctly process PHY_HALTED in phy_stop_machine()
sunhme: fix up GREG_STAT and GREG_IMASK register offsets
bpf: fix bpf_prog_get_info_by_fd to dump correct xlated_prog_len
tcp: avoid bogus gcc-7 array-bounds warning
net: tc35815: fix spelling mistake: "Intterrupt" -> "Interrupt"
bpf: don't indicate success when copy_from_user fails
udp6: fix socket leak on early demux
net: thunderx: Fix BGX transmit stall due to underflow
Revert "vhost: cache used event for better performance"
team: use a larger struct for mac address
net: check dev->addr_len for dev_set_mac_address()
phy: bcm-ns-usb3: fix MDIO_BUS dependency
...
test_tunnel_bpf.sh fails to remove the vxlan11 tunnel device, causing the
next geneve tunnelling test case fails. In addition, the geneve reserved bit
in tcbpf2_kern.c should be zero, according to the RFC.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 67a51780ae ("ipv6: udp: leverage scratch area
helpers") udp6_recvmsg() read the skb len from the scratch area,
to avoid a cache miss.
But the UDP6 rx path support RFC 2675 UDPv6 jumbograms, and their
length exceeds the 16 bits available in the scratch area. As a side
effect the length returned by recvmsg() is:
<ingress datagram len> % (1<<16)
This commit addresses the issue allocating one more bit in the
IP6CB flags field and setting it for incoming jumbograms.
Such field is still in the first cacheline, so at recvmsg()
time we can check it and fallback to access skb->len if
required, without a measurable overhead.
Fixes: 67a51780ae ("ipv6: udp: leverage scratch area helpers")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPTP set the pptp_sock_destruct as the sock's sk_destruct, it would
trigger this bug when __sk_free is invoked in atomic context, because of
the call path pptp_sock_destruct->del_chan->synchronize_rcu.
Now move the synchronize_rcu to pptp_release from del_chan. This is the
only one case which would free the sock and need the synchronize_rcu.
The following is the panic I met with kernel 3.3.8, but this issue should
exist in current kernel too according to the codes.
BUG: scheduling while atomic
__schedule_bug+0x5e/0x64
__schedule+0x55/0x580
? ppp_unregister_channel+0x1cd5/0x1de0 [ppp_generic]
? dev_hard_start_xmit+0x423/0x530
? sch_direct_xmit+0x73/0x170
__cond_resched+0x16/0x30
_cond_resched+0x22/0x30
wait_for_common+0x18/0x110
? call_rcu_bh+0x10/0x10
wait_for_completion+0x12/0x20
wait_rcu_gp+0x34/0x40
? wait_rcu_gp+0x40/0x40
synchronize_sched+0x1e/0x20
0xf8417298
0xf8417484
? sock_queue_rcv_skb+0x109/0x130
__sk_free+0x16/0x110
? udp_queue_rcv_skb+0x1f2/0x290
sk_free+0x16/0x20
__udp4_lib_rcv+0x3b8/0x650
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ccu_frac_helper_set_rate() doesn't wait for a lock bit to be
set before returning. Because of that, unstable clock may be used.
Add a wait for lock in the helper function.
Fixes: 89a3dfb787 ("clk: sunxi-ng: Add fractional lib")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
ccu_frac_helper_read_rate() prints some info which is not really
helpful except during debugging.
Replace printk() with pr_debug().
Fixes: 89a3dfb787 ("clk: sunxi-ng: Add fractional lib")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Driver for multiplier clock is missing a call to
ccu_frac_helper_enable() when fractional mode is selected.
Add a call to ccu_frac_helper_enable().
Fixes: d77e8135b3 ("clk: sunxi-ng: multiplier: Add fractional support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
N-M factor clock driver is missing a call to ccu_frac_helper_enable()
when fractional mode is used. Additionally, most SoCs require that M
factor must be set to 0 when fractional mode is used.
Without this patch, clock keeps the old value and clk_set_rate() returns
without error.
Fixes: 6174a1e24b ("clk: sunxi-ng: Add N-M-factor clock support")
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
In 04df41e343 ("bpf: update tools/include/uapi/linux/bpf.h") the files
added in 40304b2a15 ("bpf: BPF support for sock_ops") were added to
tools/include, but not in a verbatim way, missing the comments, which
ends up triggering this warning when build tools/perf/:
make: Entering directory '/home/acme/git/linux/tools/perf'
BUILD: Doing 'make -j4' parallel build
Warning: Kernel ABI header at 'tools/include/uapi/linux/bpf.h' differs from latest version at 'include/uapi/linux/bpf.h'
Make sure the the lines are equal, to fix the simple header copy
drift detector in tools/perf/.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Lawrence Brakmo <brakmo@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: 04df41e343 ("bpf: update tools/include/uapi/linux/bpf.h")
Link: http://lkml.kernel.org/n/tip-z9qyyqht9qq3yyxu76sfy0dh@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We copy headers from include/, arch/ to allow tools/ use defines,
structs from newer kernels and still be able to build on older systems.
We then, as part of a build, check if those copies got out of sync, when
we emit a warning, so that we can check if something needs to be
reflected on the tools, e.g. a 'perf trace' syscall argument beautifier
needs tweaking.
But we don't have to be super strict with that, for instance, extra
spaces, tabs or blank lines aren't problematic, so change
check-headers.sh to have "--ignore-blank-lines --ignore-space-change" as
default "diff" arguments.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-d8emqpdc3m2qtzt1ei8ra2tf@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
So that we can build on older systems where otherwise we would end up
with:
CC /tmp/build/perf/trace/beauty/ioctl.o
trace/beauty/ioctl.c: In function 'ioctl__scnprintf_tty_cmd':
trace/beauty/ioctl.c:25:17: error: 'TIOCGEXCL' undeclared (first use in this function)
trace/beauty/ioctl.c:25:17: note: each undeclared identifier is reported only once for each function it appears in
trace/beauty/ioctl.c:25:2: error: array index in initializer not of integer type
trace/beauty/ioctl.c:25:2: error: (near initialization for 'ioctl_tty_cmd')
This way we can build a tool on an older system and it will still be
capable of processing perf.data files generated on newer systems.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-8qvkv6txwuzua6d0yvt65wl3@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This reverts commit 28b45910cc ("net: bcmgenet: Remove init parameter
from bcmgenet_mii_config") because in the process of moving from
dev_info() to dev_info_once() we essentially lost the helpful printed
messages once the second instance of the driver is loaded.
dev_info_once() does not actually print the message once per device
instance, but once period.
Fixes: 28b45910cc ("net: bcmgenet: Remove init parameter from bcmgenet_mii_config")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seth Forshee noticed a performance degradation with some workloads.
This turns out to be due to packet drops. Euan Kemp noticed that this
is because we drop all packets where length exceeds the truesize, but
for some packets we add in extra memory without updating the truesize.
This in turn was kept around unchanged from ab7db91705 ("virtio-net:
auto-tune mergeable rx buffer size for improved performance"). That
commit had an internal reason not to account for the extra space: not
enough bits to do it. No longer true so let's account for the allocated
length exactly.
Many thanks to Seth Forshee for the report and bisecting and Euan Kemp
for debugging the issue.
Fixes: 680557cf79 ("virtio_net: rework mergeable buffer handling")
Reported-by: Euan Kemp <euan.kemp@coreos.com>
Tested-by: Euan Kemp <euan.kemp@coreos.com>
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to go through sk->sk_net to access the net namespace
and its sysctl variables because we allocate the sock and initialize
sk_net just a few lines earlier in the same routine.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
More Marvell PHY refactoring and cleanup
Consolidate more duplicated code into helpers, make use of core
helpers, move code into a helper for later adding functionality to add
marvell PHYs, etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1116r has code to set downshift. Refactor this into a helper, so
in future other marvell PHYs can use it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the init functions unilaterally enable set auto cross over
without using the helper. Make use of the helper, and respect the
phydev MDI configuration.
Clean up the #define used while setting polarity, and the other
functions of the bits in the register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turns out that MII_M1116R_CONTROL_REG_MAC is the same as
MII_88E1121_PHY_MSCR_REG. Refactor the code to set the RGMII delays
into a shared helper.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
