The same code is repeated a few times. Refactor into a helped.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code is repeated for different PHY versions. Put it into a
help and call when needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using an open coded equivalent, use the core
genphy_soft_reset() function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert spaces to tabs where appropriate, and fix up some otherwise
odd indentation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_irq_to_resource() has recently been fixed to return negative error #'s
along with 0 in case of failure, however the Marvell MV643xx Ethernet
driver still only regards 0 as invalid IRQ -- fix it up.
Fixes: 7a4228bbff ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs CONFIG_HAS_IOMEM and OF to be functional, but we still
let it build with COMPILE_TEST. This fixes the unmet dependency after
selecting MDIO_BCM_UNIMAC in commit mentioned below:
warning: (NET_DSA_BCM_SF2 && BCMGENET) selects MDIO_BCM_UNIMAC which has
unmet direct dependencies (NETDEVICES && MDIO_DEVICE && HAS_IOMEM &&
OF_MDIO)
Fixes: 9a4e796970 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include missing files that are provided by, used, or directly maintained
within the PHY LIBRARY, this include uapi header, header files used by
Device Tree code etc.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michał reported a NULL pointer deref during fib_sync_down_dev() when
unregistering a netdevice. The problem is that we don't check for
'in_dev' being NULL, which can happen in very specific cases.
Usually routes are flushed upon NETDEV_DOWN sent in either the netdev or
the inetaddr notification chains. However, if an interface isn't
configured with any IP address, then it's possible for host routes to be
flushed following NETDEV_UNREGISTER, after NULLing dev->ip_ptr in
inetdev_destroy().
To reproduce:
$ ip link add type dummy
$ ip route add local 1.1.1.0/24 dev dummy0
$ ip link del dev dummy0
Fix this by checking for the presence of 'in_dev' before referencing it.
Fixes: 982acb9756 ("ipv4: fib: Notify about nexthop status changes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc reported that he was not getting the PHY library adjust_link()
callback function to run when calling phy_stop() + phy_disconnect()
which does not indeed happen because we set the state machine to
PHY_HALTED but we don't get to run it to process this state past that
point.
Fix this with a synchronous call to phy_state_machine() in order to have
the state machine actually act on PHY_HALTED, set the PHY device's link
down, turn the network device's carrier off and finally call the
adjust_link() function.
Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Fixes: a390d1f379 ("phylib: convert state_queue work to delayed_work")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following stats into SCM_TIMESTAMPING_OPT_STATS control msg:
TCP_NLA_PACING_RATE
TCP_NLA_DELIVERY_RATE
TCP_NLA_SND_CWND
TCP_NLA_REORDERING
TCP_NLA_MIN_RTT
TCP_NLA_RECUR_RETRANS
TCP_NLA_DELIVERY_RATE_APP_LMT
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code to extract the function to compute delivery rate.
This function will be used in later commit.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces f2fs_statfs_project, it enables to show usage
status of directory tree which is limited with project quota.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds FS_IOC_FSSETXATTR/FS_IOC_FSGETXATTR ioctl interface
support for f2fs. The interface is kept consistent with the one
of ext4/xfs.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch changes the function names of sysfs init to follow ext4.
f2fs_init_sysfs <-> f2fs_register_sysfs
f2fs_exit_sysfs <-> f2fs_unregister_sysfs
Suggested-by: Chao Yu <yuchao0@huawei.com>
Reivewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In ->lookup(), we will have a try to recover dot or dotdot for
corrupted directory, once disk quota is on, if it allocates new
block during dotdot recovery, we need to record disk quota info
for the allocation, so this patch fixes this issue by adding
missing dquot_initialize() in __recover_dot_dentries.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch add new flag F2FS_EXTRA_ATTR storing in inode.i_inline
to indicate that on-disk structure of current inode is extended.
In order to extend, we changed the inode structure a bit:
Original one:
struct f2fs_inode {
...
struct f2fs_extent i_ext;
__le32 i_addr[DEF_ADDRS_PER_INODE];
__le32 i_nid[DEF_NIDS_PER_INODE];
}
Extended one:
struct f2fs_inode {
...
struct f2fs_extent i_ext;
union {
struct {
__le16 i_extra_isize;
__le16 i_padding;
__le32 i_extra_end[0];
};
__le32 i_addr[DEF_ADDRS_PER_INODE];
};
__le32 i_nid[DEF_NIDS_PER_INODE];
}
Once F2FS_EXTRA_ATTR is set, we will steal four bytes in the head of
i_addr field for storing i_extra_isize and i_padding. with i_extra_isize,
we can calculate actual size of reserved space in i_addr, available
attribute fields included in total extra attribute fields for current
inode can be described as below:
+--------------------+
| .i_mode |
| ... |
| .i_ext |
+--------------------+
| .i_extra_isize |-----+
| .i_padding | |
| .i_prjid | |
| .i_atime_extra | |
| .i_ctime_extra | |
| .i_mtime_extra |<----+
| .i_inode_cs |<----- store blkaddr/inline from here
| .i_xattr_cs |
| ... |
+--------------------+
| |
| block address |
| |
+--------------------+
| .i_nid |
+--------------------+
| node_footer |
| (nid, ino, offset) |
+--------------------+
Hence, with this patch, we would enhance scalability of f2fs inode for
storing more newly added attribute.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch tries to make below macros calculating max inline size,
inline dentry field size considerring reserving size-changeable
space:
- MAX_INLINE_DATA
- NR_INLINE_DENTRY
- INLINE_DENTRY_BITMAP_SIZE
- INLINE_RESERVED_SIZE
Then, when inline_{data,dentry} options is enabled, it allows us to
reserve inline space with different size flexibly for adding newly
introduced inode attribute.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds an ioctl to provide feature information to user.
For exapmle, SQLite can use this ioctl to detect whether f2fs support atomic
write or not.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Update the values to match those from the STP2002QFP documentation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, old and new PHY states are always logged.
>From now on, log only PHY state transitions.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Necessary now for gfs2_fsync and sync_file_range, but there will
eventually be other callers.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Ensure that genheaders fails with an error if too many permissions
are defined in a class to fit within an access vector. This is similar
to a check performed by checkpolicy when compiling the policy.
Also, fix the suffix on the permission constants generated by this program.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
This patch updates the dynamic-power-coefficient for big cluster on
rk3399 SoCs.
The dynamic power consumption of the CPU is proportional to the square of
the Voltage (V) and the clock frequency (f). The coefficient is used to
calculate the dynamic power as below -
Pdyn = dynamic-power-coefficient * V^2 * f
Where Voltage is in uV, frequency is in MHz.
As the following is the tested data on rk3399's big cluster.
frequency(MHz) Voltage(V) Current(mA) Dynamic-power-coefficient
24 0.8 15
48 0.8 23 ~417
96 0.8 40 ~443
216 0.8 82 ~438
312 0.8 115 ~430
408 0.8 150 ~455
So the dynamic-power-coefficient average value is about 436.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Most IP cores on ARM Rockchip platforms can only address 32 bits of
physical memory for DMA. Thus ZONE_DMA should be enabled when LPAE
is activated.
Signed-off-by: Tao Huang <huangtao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Jiri Pirko says:
====================
mlxsw: Various small fixes
This patch series is to contribute several fixes for nits that I noticed while
working on mlxsw. The changes range from typo fixes to local improvements of
the code and have little in common besides being small in scope.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Express the same logic more succinctly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer logical operator that expresses the intent to bitwise one that
happens to give the same result.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames IP2ME-specific registers reg_ralue_v and
reg_ralue_tunnel_ptr to reg_ralue_ip2me_*.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments really belong to the individual enumerators. The comment
at the register should instead reference the enum.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: bcmgenet: utilize MDIO unimac driver
This patch series migrates the Broadcom GENET driver to use the mdio-bcm-unimac
driver. This MDIO HW is the same as the one GENET internally embedds, yet for
historical reasons the two drivers lived their own lives. Because of the GENET
interrupt situation, we let it specify how it wants to signal MDIO operations
completion using its driver-private waitqueue.
The diffstat is not super impressive, but it's still negative! This would
make it easier in the future to absorb possible workarounds/bugs/features
within the same location.
This was tested on BCM7260 (GENETv5, single instance), BCM7439 (GENETv4, triple
instance) and BCM7445 (bcm_sf2 + mdio-bcm-unimac).
We also now have a nice /proc/iomem output:
f0b00000-f0b0fc4b : /rdb/ethernet@f0b00000
f0b00e14-f0b00e1c : unimac-mdio.0
f0b20000-f0b2fc4b : /rdb/ethernet@f0b20000
f0b20e14-f0b20e1c : unimac-mdio.1
f0b40000-f0b4fc4b : /rdb/ethernet@f0b40000
f0b40e14-f0b40e1c : unimac-mdio.2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_mii_init() has an error path which is strictly identical to the
unwinding that bcmgenet_mii_exit() does, so have bcmgenet_mii_init()
utilize bcmgenet_mii_exit() for that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have fully migrated to the mdio-bcm-unimac driver, drop the
legacy MDIO bus code which did duplicate a fair amount of code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the GENET driver to register an UniMAC MDIO bus controller for
the GENET internal MDIO bus, update the platform data code to attach the
PHY to the correct MDIO bus controller.
The Device Tree portion of the code is mostly left unmodified since the
lookup/binding is done via phandles and Device Tree nodes which are much
more flexible in locating and binding PHYs to their respective MDIO bus
controllers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having the bcmgenet driver migrate over the
mdio-bcm-unimac driver, add a platform data structure which allows
passing integrating specific details like bus name, wait function to
complete MDIO operations and PHY mask.
We also define what the platform device name contract is by defining
UNIMAC_MDIO_DRV_NAME and moving it to the platform_data header.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be stricly identical to what bcmgenet does, add a debug
print when a PHY workaround during bus->reset() is executed. Preliminary
change to moving bcmgenet towards mdio-bcm-unimac.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having multiple GENET instances in a system (up to
3), make sure that we do include the bus instance number in the name of
the MDIO bus such that we change it from "unimac-mdio" to
"unimac-mdio-0" for instance.
So far, the only user of this driver is using Device Tree, which uses a
lookup/parenting based technique to map PHY devices to their respective
MDIO bus controllers, hence causing no additional changes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor the code that does the busy polling on the MDIO_BUSY bit since we
will have different code-paths for for completion depending on whether
we are using interrupts or polling.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal says:
====================
tcp: remove prequeue and header prediction
During a hallway discussion with Eric Dumazet at Netdev 1.2 in
Tokyo some maybe-not-so-useful-anymore TCP stack features came up,
among these header prediction and prequeueing.
In brief, TCP prequeue assumes a single-process-blocking-read design,
which is not that common anymore. The most frequently used high-performance
networking program that is an excellent fit for these features is netperf.
The idea behind prequeueing is to move part of tcp processing, including
retransmit queue cleaning, to process context.
With (e)poll designs, prequeue is always skipped, so for such programs
this is dead-code removal.
Header prediction is also less useful nowadays.
For packet trains, GRO will do packet aggregation so we do not get the
per-packet benefit that this had before GRO anymore.
Because of SACK, header prediction also will be ineffective once
a connection suffers even light packet losses.
code removal aside, after this change processing always occurs in BH
context, this allows to experiment e.g. with doing bulk freeing of
skb heads when incoming ACKs clean packets from the retransmit queue.
There are no changes since the RFC, except in last patch (i missed
another no-longer-used mib counter). I also edited a few commit messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
was used by tcp prequeue and header prediction.
TCPFORWARDRETRANS use was removed in january.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
re-indent tcp_ack, and remove CA_ACK_SLOWPATH; it is always set now.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like prequeue, I am not sure this is overly useful nowadays.
If we receive a train of packets, GRO will aggregate them if the
headers are the same (HP predates GRO by several years) so we don't
get a per-packet benefit, only a per-aggregated-packet one.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
