commit 5509076d1b upstream.
During firmware download the device expects memory addresses in
big-endian byte order. As the wIndex parameter which hold the address is
sent in little-endian byte order regardless of host byte order, we need
to use swab16 rather than cpu_to_be16.
Also make sure to handle the struct ti_i2c_desc size parameter which is
returned in little-endian byte order.
Reported-by: Ludovic Drolez <ldrolez@debian.org>
Tested-by: Ludovic Drolez <ldrolez@debian.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10164c2ad6 upstream.
Fix driver new_id sysfs-attribute removal deadlock by making sure to
not hold any locks that the attribute operations grab when removing the
attribute.
Specifically, usb_serial_deregister holds the table mutex when
deregistering the driver, which includes removing the new_id attribute.
This can lead to a deadlock as writing to new_id increments the
attribute's active count before trying to grab the same mutex in
usb_serial_probe.
The deadlock can easily be triggered by inserting a sleep in
usb_serial_deregister and writing the id of an unbound device to new_id
during module unload.
As the table mutex (in this case) is used to prevent subdriver unload
during probe, it should be sufficient to only hold the lock while
manipulating the usb-serial driver list during deregister. A racing
probe will then either fail to find a matching subdriver or fail to get
the corresponding module reference.
Since v3.15-rc1 this also triggers the following lockdep warning:
======================================================
[ INFO: possible circular locking dependency detected ]
3.15.0-rc2 #123 Tainted: G W
-------------------------------------------------------
modprobe/190 is trying to acquire lock:
(s_active#4){++++.+}, at: [<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
but task is already holding lock:
(table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (table_lock){+.+.+.}:
[<c0075f84>] __lock_acquire+0x1694/0x1ce4
[<c0076de8>] lock_acquire+0xb4/0x154
[<c03af3cc>] _raw_spin_lock+0x4c/0x5c
[<c02bbc24>] usb_store_new_id+0x14c/0x1ac
[<bf007eb4>] new_id_store+0x68/0x70 [usbserial]
[<c025f568>] drv_attr_store+0x30/0x3c
[<c01690e0>] sysfs_kf_write+0x5c/0x60
[<c01682c0>] kernfs_fop_write+0xd4/0x194
[<c010881c>] vfs_write+0xbc/0x198
[<c0108e4c>] SyS_write+0x4c/0xa0
[<c000f880>] ret_fast_syscall+0x0/0x48
-> #0 (s_active#4){++++.+}:
[<c03a7a28>] print_circular_bug+0x68/0x2f8
[<c0076218>] __lock_acquire+0x1928/0x1ce4
[<c0076de8>] lock_acquire+0xb4/0x154
[<c0166b70>] __kernfs_remove+0x254/0x310
[<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
[<c0169fb8>] remove_files.isra.1+0x48/0x84
[<c016a2fc>] sysfs_remove_group+0x58/0xac
[<c016a414>] sysfs_remove_groups+0x34/0x44
[<c02623b8>] driver_remove_groups+0x1c/0x20
[<c0260e9c>] bus_remove_driver+0x3c/0xe4
[<c026235c>] driver_unregister+0x38/0x58
[<bf007fb4>] usb_serial_bus_deregister+0x84/0x88 [usbserial]
[<bf004db4>] usb_serial_deregister+0x6c/0x78 [usbserial]
[<bf005330>] usb_serial_deregister_drivers+0x2c/0x4c [usbserial]
[<bf016618>] usb_serial_module_exit+0x14/0x1c [sierra]
[<c009d6cc>] SyS_delete_module+0x184/0x210
[<c000f880>] ret_fast_syscall+0x0/0x48
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(table_lock);
lock(s_active#4);
lock(table_lock);
lock(s_active#4);
*** DEADLOCK ***
1 lock held by modprobe/190:
#0: (table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
stack backtrace:
CPU: 0 PID: 190 Comm: modprobe Tainted: G W 3.15.0-rc2 #123
[<c0015e10>] (unwind_backtrace) from [<c0013728>] (show_stack+0x20/0x24)
[<c0013728>] (show_stack) from [<c03a9a54>] (dump_stack+0x24/0x28)
[<c03a9a54>] (dump_stack) from [<c03a7cac>] (print_circular_bug+0x2ec/0x2f8)
[<c03a7cac>] (print_circular_bug) from [<c0076218>] (__lock_acquire+0x1928/0x1ce4)
[<c0076218>] (__lock_acquire) from [<c0076de8>] (lock_acquire+0xb4/0x154)
[<c0076de8>] (lock_acquire) from [<c0166b70>] (__kernfs_remove+0x254/0x310)
[<c0166b70>] (__kernfs_remove) from [<c0167aa0>] (kernfs_remove_by_name_ns+0x4c/0x94)
[<c0167aa0>] (kernfs_remove_by_name_ns) from [<c0169fb8>] (remove_files.isra.1+0x48/0x84)
[<c0169fb8>] (remove_files.isra.1) from [<c016a2fc>] (sysfs_remove_group+0x58/0xac)
[<c016a2fc>] (sysfs_remove_group) from [<c016a414>] (sysfs_remove_groups+0x34/0x44)
[<c016a414>] (sysfs_remove_groups) from [<c02623b8>] (driver_remove_groups+0x1c/0x20)
[<c02623b8>] (driver_remove_groups) from [<c0260e9c>] (bus_remove_driver+0x3c/0xe4)
[<c0260e9c>] (bus_remove_driver) from [<c026235c>] (driver_unregister+0x38/0x58)
[<c026235c>] (driver_unregister) from [<bf007fb4>] (usb_serial_bus_deregister+0x84/0x88 [usbserial])
[<bf007fb4>] (usb_serial_bus_deregister [usbserial]) from [<bf004db4>] (usb_serial_deregister+0x6c/0x78 [usbserial])
[<bf004db4>] (usb_serial_deregister [usbserial]) from [<bf005330>] (usb_serial_deregister_drivers+0x2c/0x4c [usbserial])
[<bf005330>] (usb_serial_deregister_drivers [usbserial]) from [<bf016618>] (usb_serial_module_exit+0x14/0x1c [sierra])
[<bf016618>] (usb_serial_module_exit [sierra]) from [<c009d6cc>] (SyS_delete_module+0x184/0x210)
[<c009d6cc>] (SyS_delete_module) from [<c000f880>] (ret_fast_syscall+0x0/0x48)
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e01280d28 upstream.
This reverts commit 1ebca9dad5.
This device was erroneously added to the sierra driver even though it's
not a Sierra device and was already handled by the option driver.
Cc: Richard Farina <sidhayn@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd73bd8831 upstream.
Fix regression introduced by commit 8e493ca176 ("USB: usb_wwan: fix
bulk-urb allocation") by making sure to require both bulk-in and out
endpoints during port probe.
The original option driver (which usb_wwan is based on) was written
under the assumption that either endpoint could be missing, but
evidently this cannot have been tested properly. Specifically, it would
handle opening a device without bulk-in (but would blow up during resume
which was implemented later), but not a missing bulk-out in write()
(although it is handled in some places such as write_room()).
Fortunately (?), the driver also got the test for missing endpoints
wrong so the urbs were in fact always allocated, although they would be
initialised using the wrong endpoint address (0) and any submission of
such an urb would fail.
The commit mentioned above fixed the test for missing endpoints but
thereby exposed the other bugs which would now generate null-pointer
exceptions rather than failed urb submissions.
The regression was introduced in v3.7, but the offending commit was also
marked for stable.
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 895d240d1d upstream.
By specifying NO_UNION_NORMAL the ACM driver does only use the first two
USB interfaces (modem data & control). The AT Port, Diagnostic and NMEA
interfaces are left to the USB serial driver.
Signed-off-by: Michael Ulbricht <michael.ulbricht@systec-electronic.com>
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29c7787075 upstream.
David Vrabel identified a regression when using automatic NUMA balancing
under Xen whereby page table entries were getting corrupted due to the
use of native PTE operations. Quoting him
Xen PV guest page tables require that their entries use machine
addresses if the preset bit (_PAGE_PRESENT) is set, and (for
successful migration) non-present PTEs must use pseudo-physical
addresses. This is because on migration MFNs in present PTEs are
translated to PFNs (canonicalised) so they may be translated back
to the new MFN in the destination domain (uncanonicalised).
pte_mknonnuma(), pmd_mknonnuma(), pte_mknuma() and pmd_mknuma()
set and clear the _PAGE_PRESENT bit using pte_set_flags(),
pte_clear_flags(), etc.
In a Xen PV guest, these functions must translate MFNs to PFNs
when clearing _PAGE_PRESENT and translate PFNs to MFNs when setting
_PAGE_PRESENT.
His suggested fix converted p[te|md]_[set|clear]_flags to using
paravirt-friendly ops but this is overkill. He suggested an alternative
of using p[te|md]_modify in the NUMA page table operations but this is
does more work than necessary and would require looking up a VMA for
protections.
This patch modifies the NUMA page table operations to use paravirt
friendly operations to set/clear the flags of interest. Unfortunately
this will take a performance hit when updating the PTEs on
CONFIG_PARAVIRT but I do not see a way around it that does not break
Xen.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Noonan <steven@uplinklabs.net>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7848a4bf51 upstream.
soft lockup in freeing gigantic hugepage fixed in commit 55f67141a8 "mm:
hugetlb: fix softlockup when a large number of hugepages are freed." can
happen in return_unused_surplus_pages(), so let's fix it.
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5a8cad376 upstream.
Sasha Levin has reported two THP BUGs[1][2]. I believe both of them
have the same root cause. Let's look to them one by one.
The first bug[1] is "kernel BUG at mm/huge_memory.c:1829!". It's
BUG_ON(mapcount != page_mapcount(page)) in __split_huge_page(). From my
testing I see that page_mapcount() is higher than mapcount here.
I think it happens due to race between zap_huge_pmd() and
page_check_address_pmd(). page_check_address_pmd() misses PMD which is
under zap:
CPU0 CPU1
zap_huge_pmd()
pmdp_get_and_clear()
__split_huge_page()
anon_vma_interval_tree_foreach()
__split_huge_page_splitting()
page_check_address_pmd()
mm_find_pmd()
/*
* We check if PMD present without taking ptl: no
* serialization against zap_huge_pmd(). We miss this PMD,
* it's not accounted to 'mapcount' in __split_huge_page().
*/
pmd_present(pmd) == 0
BUG_ON(mapcount != page_mapcount(page)) // CRASH!!!
page_remove_rmap(page)
atomic_add_negative(-1, &page->_mapcount)
The second bug[2] is "kernel BUG at mm/huge_memory.c:1371!".
It's VM_BUG_ON_PAGE(!PageHead(page), page) in zap_huge_pmd().
This happens in similar way:
CPU0 CPU1
zap_huge_pmd()
pmdp_get_and_clear()
page_remove_rmap(page)
atomic_add_negative(-1, &page->_mapcount)
__split_huge_page()
anon_vma_interval_tree_foreach()
__split_huge_page_splitting()
page_check_address_pmd()
mm_find_pmd()
pmd_present(pmd) == 0 /* The same comment as above */
/*
* No crash this time since we already decremented page->_mapcount in
* zap_huge_pmd().
*/
BUG_ON(mapcount != page_mapcount(page))
/*
* We split the compound page here into small pages without
* serialization against zap_huge_pmd()
*/
__split_huge_page_refcount()
VM_BUG_ON_PAGE(!PageHead(page), page); // CRASH!!!
So my understanding the problem is pmd_present() check in mm_find_pmd()
without taking page table lock.
The bug was introduced by me commit with commit 117b0791ac. Sorry for
that. :(
Let's open code mm_find_pmd() in page_check_address_pmd() and do the
check under page table lock.
Note that __page_check_address() does the same for PTE entires
if sync != 0.
I've stress tested split and zap code paths for 36+ hours by now and
don't see crashes with the patch applied. Before it took <20 min to
trigger the first bug and few hours for second one (if we ignore
first).
[1] https://lkml.kernel.org/g/<53440991.9090001@oracle.com>
[2] https://lkml.kernel.org/g/<5310C56C.60709@oracle.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Bob Liu <lliubbo@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michel Lespinasse <walken@google.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82c04ff89e upstream.
The SYSTEM_TRUSTED_KEYRING config option is not in any menu, causing it
to show up in the toplevel of the kernel configuration. Fix this by
moving it under the General Setup menu.
Signed-off-by: Peter Foley <pefoley2@pefoley.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 561a4fe851 upstream.
As trace event triggers are now part of the mainline kernel, I added
my trace event trigger tests to my test suite I run on all my kernels.
Now these tests get run under different config options, and one of
those options is CONFIG_PROVE_RCU, which checks under lockdep that
the rcu locking primitives are being used correctly. This triggered
the following splat:
===============================
[ INFO: suspicious RCU usage. ]
3.15.0-rc2-test+ #11 Not tainted
-------------------------------
kernel/trace/trace_events_trigger.c:80 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
4 locks held by swapper/1/0:
#0: ((&(&j_cdbs->work)->timer)){..-...}, at: [<ffffffff8104d2cc>] call_timer_fn+0x5/0x1be
#1: (&(&pool->lock)->rlock){-.-...}, at: [<ffffffff81059856>] __queue_work+0x140/0x283
#2: (&p->pi_lock){-.-.-.}, at: [<ffffffff8106e961>] try_to_wake_up+0x2e/0x1e8
#3: (&rq->lock){-.-.-.}, at: [<ffffffff8106ead3>] try_to_wake_up+0x1a0/0x1e8
stack backtrace:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.15.0-rc2-test+ #11
Hardware name: /DG965MQ, BIOS MQ96510J.86A.0372.2006.0605.1717 06/05/2006
0000000000000001 ffff88007e083b98 ffffffff819f53a5 0000000000000006
ffff88007b0942c0 ffff88007e083bc8 ffffffff81081307 ffff88007ad96d20
0000000000000000 ffff88007af2d840 ffff88007b2e701c ffff88007e083c18
Call Trace:
<IRQ> [<ffffffff819f53a5>] dump_stack+0x4f/0x7c
[<ffffffff81081307>] lockdep_rcu_suspicious+0x107/0x110
[<ffffffff810ee51c>] event_triggers_call+0x99/0x108
[<ffffffff810e8174>] ftrace_event_buffer_commit+0x42/0xa4
[<ffffffff8106aadc>] ftrace_raw_event_sched_wakeup_template+0x71/0x7c
[<ffffffff8106bcbf>] ttwu_do_wakeup+0x7f/0xff
[<ffffffff8106bd9b>] ttwu_do_activate.constprop.126+0x5c/0x61
[<ffffffff8106eadf>] try_to_wake_up+0x1ac/0x1e8
[<ffffffff8106eb77>] wake_up_process+0x36/0x3b
[<ffffffff810575cc>] wake_up_worker+0x24/0x26
[<ffffffff810578bc>] insert_work+0x5c/0x65
[<ffffffff81059982>] __queue_work+0x26c/0x283
[<ffffffff81059999>] ? __queue_work+0x283/0x283
[<ffffffff810599b7>] delayed_work_timer_fn+0x1e/0x20
[<ffffffff8104d3a6>] call_timer_fn+0xdf/0x1be^M
[<ffffffff8104d2cc>] ? call_timer_fn+0x5/0x1be
[<ffffffff81059999>] ? __queue_work+0x283/0x283
[<ffffffff8104d823>] run_timer_softirq+0x1a4/0x22f^M
[<ffffffff8104696d>] __do_softirq+0x17b/0x31b^M
[<ffffffff81046d03>] irq_exit+0x42/0x97
[<ffffffff81a08db6>] smp_apic_timer_interrupt+0x37/0x44
[<ffffffff81a07a2f>] apic_timer_interrupt+0x6f/0x80
<EOI> [<ffffffff8100a5d8>] ? default_idle+0x21/0x32
[<ffffffff8100a5d6>] ? default_idle+0x1f/0x32
[<ffffffff8100ac10>] arch_cpu_idle+0xf/0x11
[<ffffffff8107b3a4>] cpu_startup_entry+0x1a3/0x213
[<ffffffff8102a23c>] start_secondary+0x212/0x219
The cause is that the triggers are protected by rcu_read_lock_sched() but
the data is dereferenced with rcu_dereference() which expects it to
be protected with rcu_read_lock(). The proper reference should be
rcu_dereference_sched().
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da1aab3dca upstream.
When performing a user-request check/repair (MD_RECOVERY_REQUEST is set)
on a raid1, we allocate multiple bios each with their own set of pages.
If the page allocations for one bio fails, we currently do *not* free
the pages allocated for the previous bios, nor do we free the bio itself.
This patch frees all the already-allocate pages, and makes sure that
all the bios are freed as well.
This bug can cause a memory leak which can ultimately OOM a machine.
It was introduced in 3.10-rc1.
Fixes: a07876064a
Cc: Kent Overstreet <koverstreet@google.com>
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f433083e8 upstream.
This touchpad seriously dislikes init reports, not only timeing out, but
also refusing to work after this.
Reported-and-tested-by: Vincent Fortier <th0ma7@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e24d0d399b upstream.
The Microsoft Surface Type/Touch Cover 2 is a fancy device which advertised
itself as a multitouch device but with constant input reports.
This way, hid_scan_report() gives the group MULTITOUCH to it, but
hid-multitouch can not handle it due to the constant collection ignored
by hid-input.
To prevent such crap in the future, and while we do not fix this particular
device, make the scan_report coherent with hid-input.c, and ignore constant
input reports.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3b0cbce01 upstream.
This reverts commit 117309c51d.
The MS Surface Pro 2 has an USB composite device with 3 interfaces
- interface 0 - sensor hub
- interface 1 - wacom digitizer
- interface 2 - the keyboard cover, if one is attached
This USB composite device changes it product id dependent on if and which
keyboard cover is attached. Adding the covers to hid_have_special_driver
prevents loading the right hid drivers for the other two interfaces, all 3
get loaded with hid-microsoft. We don't even need hid-microsoft for the
keyboards. We have to revert this to load the right hid modules for each
interface.
Signed-off-by: Derya <derya.kiran@yahoo.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05a812ac47 upstream.
FIFO event channels require bitops on 32-bit aligned values (the event
words). Linux's bitops require unsigned long alignment which may be
64-bits.
On arm64 an incorrectly unaligned access will fault.
Fix this by aligning the bitops along with an adjustment for bit
position and using an unsigned long for the local copy of the ready
word.
Signed-off-by: Vladimir Murzin <murzin.v@gmail.com>
Tested-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Reviewed-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0fc17a936 upstream.
The git commit a945928ea2
('xen: Do not enable spinlocks before jump_label_init() has executed')
was added to deal with the jump machinery. Earlier the code
that turned on the jump label was only called by Xen specific
functions. But now that it had been moved to the initcall machinery
it gets called on Xen, KVM, and baremetal - ouch!. And the detection
machinery to only call it on Xen wasn't remembered in the heat
of merge window excitement.
This means that the slowpath is enabled on baremetal while it should
not be.
Reported-by: Waiman Long <waiman.long@hp.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
CC: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c11f1df500 upstream.
Problem reported in Red Hat bz 1040329 for strict writes where we cache
only when we hold oplock and write direct to the server when we don't.
When we receive an oplock break, we first change the oplock value for
the inode in cifsInodeInfo->oplock to indicate that we no longer hold
the oplock before we enqueue a task to flush changes to the backing
device. Once we have completed flushing the changes, we return the
oplock to the server.
There are 2 ways here where we can have data corruption
1) While we flush changes to the backing device as part of the oplock
break, we can have processes write to the file. These writes check for
the oplock, find none and attempt to write directly to the server.
These direct writes made while we are flushing from cache could be
overwritten by data being flushed from the cache causing data
corruption.
2) While a thread runs in cifs_strict_writev, the machine could receive
and process an oplock break after the thread has checked the oplock and
found that it allows us to cache and before we have made changes to the
cache. In that case, we end up with a dirty page in cache when we
shouldn't have any. This will be flushed later and will overwrite all
subsequent writes to the part of the file represented by this page.
Before making any writes to the server, we need to confirm that we are
not in the process of flushing data to the server and if we are, we
should wait until the process is complete before we attempt the write.
We should also wait for existing writes to complete before we process
an oplock break request which changes oplock values.
We add a version specific downgrade_oplock() operation to allow for
differences in the oplock values set for the different smb versions.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd20908a8a upstream.
it's pointless and actually leads to wrong behaviour in at least one
moderately convoluted case (pipe(), close one end, try to get to
another via /proc/*/fd and run into ETXTBUSY).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0d8898d76 upstream.
There are only a couple of architectures that override _STK_LIM_MAX to
a non-infinity value. This changes the stack allocation semantics in
subtle ways. For example, GNU make changes its stack allocation to the
hard maximum defined by _STK_LIM_MAX. As a results, threads executed
by processes running under make are allocated a stack size of
_STK_LIM_MAX rather than a sensible default value. This causes various
thread stress tests to fail when they can't muster more than about 50
threads.
The attached change implements the default behavior used by the
majority of architectures.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Reviewed-by: Carlos O'Donell <carlos@systemhalted.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab3e55b119 upstream.
This bug was detected with the libio-epoll-perl debian package where the
test case IO-Ppoll-compat.t failed.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ef36bd2b3 upstream.
On parisc, SHMLBA was defined to 0x00400000 (4MB) to reflect that we need to
take care of our caches for shared mappings. But actually, we can map a file at
any multiple address of PAGE_SIZE, so let us correct that now with a value of
PAGE_SIZE for SHMLBA. Instead we now take care of this cache colouring via the
constant SHM_COLOUR while we map shared pages.
Signed-off-by: Helge Deller <deller@gmx.de>
CC: Jeroen Roovers <jer@gentoo.org>
CC: John David Anglin <dave.anglin@bell.net>
CC: Carlos O'Donell <carlos@systemhalted.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03e6bdc5c4 upstream.
In tick_do_update_jiffies64() we are processing ticks only if delta is
greater than tick_period. This is what we are supposed to do here and
it broke a bit with this patch:
commit 47a1b796 (tick/timekeeping: Call update_wall_time outside the
jiffies lock)
With above patch, we might end up calling update_wall_time() even if
delta is found to be smaller that tick_period. Fix this by returning
when the delta is less than tick period.
[ tglx: Made it a 3 liner and massaged changelog ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: fweisbec@gmail.com
Cc: Arvind.Chauhan@arm.com
Cc: linaro-networking@linaro.org
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/80afb18a494b0bd9710975bcc4de134ae323c74f.1397537987.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts the bisected regressing
commit bc0bb9fd1c
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Nov 14 12:14:29 2013 +0200
drm/i915: remove QUIRK_NO_PCH_PWM_ENABLE
restoring QUIRK_NO_PCH_PWM_ENABLE for a couple of Dell XPS models which
broke in 3.14.
There is no such revert upstream. We have root caused and fixed the
issue upstream, without the quirk, with:
commit 39fbc9c8f6
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:22:06 2014 +0300
drm/i915: check VBT for supported backlight type
and
commit c675949ec5
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
While the commits are within the stable rules otherwise, and fix more
machines than just the regressed Dell XPS models, we feel backporting
them to stable may be too risky. The revert is limited to the broken
machines, and the impact should be effectively the same as what the
upstream commits do more generally.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76276
Reported-by: Romain Francoise <romain@orebokech.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Romain Francoise <romain@orebokech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42dd037c08 upstream.
Doing rbd_obj_request_put() in rbd_img_request_fill() error paths is
not only insufficient, but also triggers an rbd_assert() in
rbd_obj_request_destroy():
Assertion failure in rbd_obj_request_destroy() at line 1867:
rbd_assert(obj_request->img_request == NULL);
rbd_img_obj_request_add() adds obj_requests to the img_request, the
opposite is rbd_img_obj_request_del(). Use it.
Fixes: http://tracker.ceph.com/issues/7327
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dec935a3a upstream.
No reason to allocate tp_module structures for modules that have no
tracepoints. This just wastes memory.
Fixes: b75ef8b44b "Tracepoint: Dissociate from module mutex"
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many people reported preemption/reschedule problems with i386 kernels
for .13 and .14. After Michele bisected this to a combination of
3e8e42c69bb ("sched: Revert need_resched() to look at TIF_NEED_RESCHED")
ded7975475 ("irq: Force hardirq exit's softirq processing on its own stack")
it finally dawned on me that i386's current_thread_info() was to
blame.
When we are on interrupt/exception stacks, we fail to observe the
right TIF_NEED_RESCHED bit and therefore the PREEMPT_NEED_RESCHED
folding malfunctions.
Current upstream fixes this by making i386 behave the same as x86_64
already did:
2432e1364b ("x86: Nuke the supervisor_stack field in i386 thread_info")
b807902a88 ("x86: Nuke GET_THREAD_INFO_WITH_ESP() macro for i386")
0788aa6a23 ("x86: Prepare removal of previous_esp from i386 thread_info structure")
198d208df4 ("x86: Keep thread_info on thread stack in x86_32")
However, that is far too much to stuff into -stable. Therefore I
propose we merge the below patch which uses task_thread_info(current)
for tif_need_resched() instead of the ESP based current_thread_info().
This makes sure we always observe the one true TIF_NEED_RESCHED bit
and things will work as expected again.
Cc: bp@alien8.de
Cc: fweisbec@gmail.com
Cc: david.a.cohen@linux.intel.com
Cc: mingo@kernel.org
Cc: fweisbec@gmail.com
Cc: greg@kroah.com
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: gregkh@linuxfoundation.org
Cc: pbonzini@redhat.com
Cc: rostedt@goodmis.org
Cc: stefan.bader@canonical.com
Cc: mingo@kernel.org
Cc: toralf.foerster@gmx.de
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: torvalds@linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: <stable-commits@vger.kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: peterz@infradead.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: barra_cuda@katamail.com
Tested-by: Stefan Bader <stefan.bader@canonical.com>
Tested-by: Toralf F¿rster <toralf.foerster@gmx.de>
Tested-by: Michele Ballabio <barra_cuda@katamail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140409142447.GD13658@twins.programming.kicks-ass.net
commit a9bdd83656 upstream.
Currently, nf_tables trims off the set name if it exceeeds 15
bytes, so explicitly reject set names that are too large.
Reported-by: Giuseppe Longo <giuseppelng@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c58dd2dd44 upstream.
All xtables variants suffer from the defect that the copy_to_user()
to copy the counters to user memory may fail after the table has
already been exchanged and thus exposed. Return an error at this
point will result in freeing the already exposed table. Any
subsequent packet processing will result in a kernel panic.
We can't copy the counters before exposing the new tables as we
want provide the counter state after the old table has been
unhooked. Therefore convert this into a silent error.
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af5040da01 upstream.
trace_block_rq_complete does not take into account that request can
be partially completed, so we can get the following incorrect output
of blkparser:
C R 232 + 240 [0]
C R 240 + 232 [0]
C R 248 + 224 [0]
C R 256 + 216 [0]
but should be:
C R 232 + 8 [0]
C R 240 + 8 [0]
C R 248 + 8 [0]
C R 256 + 8 [0]
Also, the whole output summary statistics of completed requests and
final throughput will be incorrect.
This patch takes into account real completion size of the request and
fixes wrong completion accounting.
Signed-off-by: Roman Pen <r.peniaev@gmail.com>
CC: Steven Rostedt <rostedt@goodmis.org>
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: Ingo Molnar <mingo@redhat.com>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 223b02d923 upstream.
"len" contains sizeof(nf_ct_ext) and size of extensions. In a worst
case it can contain all extensions. Bellow you can find sizes for all
types of extensions. Their sum is definitely bigger than 256.
nf_ct_ext_types[0]->len = 24
nf_ct_ext_types[1]->len = 32
nf_ct_ext_types[2]->len = 24
nf_ct_ext_types[3]->len = 32
nf_ct_ext_types[4]->len = 152
nf_ct_ext_types[5]->len = 2
nf_ct_ext_types[6]->len = 16
nf_ct_ext_types[7]->len = 8
I have seen "len" up to 280 and my host has crashes w/o this patch.
The right way to fix this problem is reducing the size of the ecache
extension (4) and Florian is going to do this, but these changes will
be quite large to be appropriate for a stable tree.
Fixes: 5b423f6a40 (netfilter: nf_conntrack: fix racy timer handling with reliable)
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b855d416dc upstream.
nft_cmp_fast is used for equality comparisions of size <= 4. For
comparisions of size < 4 byte a mask is calculated that is applied to
both the data from userspace (during initialization) and the register
value (during runtime). Both values are stored using (in effect) memcpy
to a memory area that is then interpreted as u32 by nft_cmp_fast.
This works fine on little endian since smaller types have the same base
address, however on big endian this is not true and the smaller types
are interpreted as a big number with trailing zero bytes.
The mask therefore must not include the lower bytes, but the higher bytes
on big endian. Add a helper function that does a cpu_to_le32 to switch
the bytes on big endian. Since we're dealing with a mask of just consequitive
bits, this works out fine.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c92cdeb45e upstream.
sys_getppid() returns the parent pid of the current process in its own pid
namespace. Since audit filters are based in the init pid namespace, a process
could avoid a filter or trigger an unintended one by being in an alternate pid
namespace or log meaningless information.
Switch to task_ppid_nr() for PPIDs to anchor all audit filters in the
init_pid_ns.
(informed by ebiederman's 6c621b7e)
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad36d28293 upstream.
Added the functions task_ppid_nr_ns() and task_ppid_nr() to abstract the lookup
of the PPID (real_parent's pid_t) of a process, including rcu locking, in the
arbitrary and init_pid_ns.
This provides an alternative to sys_getppid(), which is relative to the child
process' pid namespace.
(informed by ebiederman's 6c621b7e)
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de04f8657d upstream.
Commit 12e55569a2 "tools lib traceevent: Use helper trace-seq in print
functions like kernel does" added a extra trace_seq helper to process
string arguments like the kernel does it. But the difference between the
kernel and the userspace library is that the kernel's trace_seq structure
has a static allocated buffer. The userspace one has a dynamically
allocated one. It requires a trace_seq_destroy(), otherwise it produces
a nasty memory leak.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20140422192330.6bb09bf8@gandalf.local.home
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b351c39cc9 upstream.
Function and callers can be preempted.
https://bugzilla.kernel.org/show_bug.cgi?id=73721
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3de2260140 upstream.
pthru32->dataxferlen comes from the user so we need to check that it's
not too large so we don't overflow the buffer.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2495e228f upstream.
In the highly unusual case where two threads are running concurrently through
the scanning code scanning the same target, we run into the situation where
one may allocate the target while the other is still using it. In this case,
because the reap checks for STARGET_CREATED and kills the target without
reference counting, the second thread will do the wrong thing on reap.
Fix this by reference counting even creates and doing the STARGET_CREATED
check in the final put.
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e63ed0d7a9 upstream.
This patch eliminates the reap_ref and replaces it with a proper kref.
On last put of this kref, the target is removed from visibility in
sysfs. The final call to scsi_target_reap() for the device is done from
__scsi_remove_device() and only if the device was made visible. This
ensures that the target disappears as soon as the last device is gone
rather than waiting until final release of the device (which is often
too long).
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14262d67fe upstream.
If you are using a 64-bit kernel with 32-bit userland, then
scripts/gcc-x86_64-has-stack-protector.sh invokes 32-bit gcc
with -mcmodel=kernel, which produces:
<stdin>:1:0: error: code model 'kernel' not supported in the 32 bit mode
and trips the "broken compiler" test at arch/x86/Makefile:120.
There are several places a fix is possible, but the following seems
cleanest. (But it's minimal; it would also be possible to factor
out a bunch of stuff from the two branches of the if.)
Signed-off-by: George Spelvin <linux@horizon.com>
Link: http://lkml.kernel.org/r/20140507210552.7581.qmail@ns.horizon.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
