[ Upstream commit bdd5a14e66 ]
The bridge has three bootstrap pins which are sampled to determine the
frequency of the external reference clock. The driver will also
(over)write that setting. But it seems this is racy after the bridge is
enabled. It was observed that although the driver write the correct
value (by sniffing on the I2C bus), the register has the wrong value.
The datasheet states that the GPIO lines have to be stable for at least
5us after asserting the EN signal. Thus, there seems to be some logic
which samples the GPIO lines and this logic appears to overwrite the
register value which was set by the driver. Waiting 20us after
asserting the EN line resolves this issue.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250821122341.1257286-1-mwalle@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dedf9c93de ]
Clear the error flags after disabling the module to avoid the case when
a flag is set again between flag clear and module disable. And use
SR_CLEAR_MASK to replace hardcoded value for improved readability.
Although fsl_lpspi_reset() was only introduced in commit a15dc3d657
("spi: lpspi: Fix CLK pin becomes low before one transfer"), the
original driver only reset SR in the interrupt handler, making it
vulnerable to the same issue. Therefore the fixes commit is set at the
introduction of the driver.
Fixes: 5314987de5 ("spi: imx: add lpspi bus driver")
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Link: https://patch.msgid.link/20250828-james-nxp-lpspi-v2-4-6262b9aa9be4@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e811b088a3 ]
In DMA mode fsl_lpspi_reset() is always called at the end, even when the
transfer is aborted. In PIO mode aborts skip the reset leaving the FIFO
filled and the module enabled.
Fix it by always calling fsl_lpspi_reset().
Fixes: a15dc3d657 ("spi: lpspi: Fix CLK pin becomes low before one transfer")
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Link: https://patch.msgid.link/20250828-james-nxp-lpspi-v2-3-6262b9aa9be4@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbe3370586 ]
The driver currently supports multiple chip-selects, but only sets the
polarity for the first one (CS 0). Fix it by setting the PCSPOL bit for
the desired chip-select.
Fixes: 5314987de5 ("spi: imx: add lpspi bus driver")
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250828-james-nxp-lpspi-v2-2-6262b9aa9be4@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 782a7c7307 ]
Commit 6a13044849 ("spi: lpspi: Fix wrong transmission when don't use
CONT") breaks transmissions when CONT is used. The TDIE interrupt should
not be disabled in all cases. If CONT is used and the TX transfer is not
yet completed yet, but the interrupt handler is called because there are
characters to be received, TDIE is replaced with FCIE. When the transfer
is finally completed, SR_TDF is set but the interrupt handler isn't
called again.
Fixes: 6a13044849 ("spi: lpspi: Fix wrong transmission when don't use CONT")
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250828-james-nxp-lpspi-v2-1-6262b9aa9be4@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 708e2371f7 ]
Reinstate the rotational media flag for the CD-ROM driver. The flag has
been cleared since commit bd4a633b6f ("block: move the nonrot flag to
queue_limits") and this breaks some applications.
Move queue limit configuration from get_sectorsize() to
sr_revalidate_disk() and set the rotational flag.
Cc: Christoph Hellwig <hch@lst.de>
Fixes: bd4a633b6f ("block: move the nonrot flag to queue_limits")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250827113550.2614535-1-ming.lei@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa427d7b73 ]
Add a helper that freezes the queue, updates the queue limits and
unfreezes the queue and convert all open coded versions of that to the
new helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20250110054726.1499538-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 708e2371f7 ("scsi: sr: Reinstate rotational media flag")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1180c79fbf ]
The fans controlled by the driver can get stuck at 0 RPM if they are
configured below a 20% duty cycle. The driver tries to avoid this by
enforcing a minimum duty cycle of 20%, but this is done after the fans
are registered with the thermal subsystem. This is too late as the
thermal subsystem can set their current state before the driver is able
to enforce the minimum duty cycle.
Fix by setting the minimum duty cycle before registering the fans with
the thermal subsystem.
Fixes: d7efb2ebc7 ("hwmon: (mlxreg-fan) Extend driver to support multiply cooling devices")
Reported-by: Nikolay Aleksandrov <razor@blackwall.org>
Tested-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20250730201715.1111133-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa28991fd5 ]
Currently, tpmi_get_logical_id() calls topology_physical_package_id()
to set the pkg_id of the info structure. Since some VM hosts assign non
contiguous package IDs, topology_physical_package_id() can return a
larger value than topology_max_packages(). This will result in an
invalid reference into tpmi_power_domain_mask[] as that is allocatead
based on topology_max_packages() as the maximum package ID.
Fixes: 17ca278045 ("platform/x86/intel: TPMI domain id and CPU mapping")
Signed-off-by: David Arcari <darcari@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20250829113859.1772827-1-darcari@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf3940ac73 ]
Currently, the ignore_key_wlan quirk applies to keycodes 0x5D, 0x5E, and
0x5F. However, the relevant code for the Asus Zenbook Duo is only 0x5F.
Since this code is emitted by other Asus devices, such as from the Z13
for its ROG button, remove the extra codes before expanding the quirk.
For the Duo devices, which are the only ones that use this quirk, there
should be no effect.
Fixes: 9286dfd573 ("platform/x86: asus-wmi: Fix spurious rfkill on UX8406MA")
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://lore.kernel.org/r/20250808154710.8981-1-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a81f78caa ]
In the do_validate_mem(), the call to add_interval() does not
handle errors. If kmalloc() fails in add_interval(), it could
result in a null pointer being inserted into the linked list,
leading to illegal memory access when sub_interval() is called
next.
This patch adds an error handling for the add_interval(). If
add_interval() returns an error, the function will return early
with the error code.
Fixes: 7b4884ca88 ("pcmcia: validate late-added resources")
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 71598a5a77 which is
commit 1f02f2044b upstream.
This commit introduced a regression, however the fix for the regression:
aa5fc4362f ("drm/amdgpu: fix task hang from failed job submission
during process kill") depends on things not yet present in 6.12.y and
older kernels. Since this commit is more of an optimization, just
revert it for 6.12.y and older stable kernels.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x - 6.12.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcd6659d49 upstream.
It was reported that HP EliteDesk 800 G4 DM 65W (SSID 103c:845a) needs
the similar quirk for enabling HDMI outputs, too. This patch adds the
corresponding quirk entry.
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20250901115009.27498-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8851e27d2c upstream.
Starting with Rust 1.91.0 (expected 2025-10-30), the target spec format
has changed the type of the `target-pointer-width` key from string
to integer [1].
Thus conditionally use one or the other depending on the version.
Cc: Waffle Maybe <waffle.lapkin@gmail.com>
Link: https://github.com/rust-lang/rust/pull/144443 [1]
Link: https://lore.kernel.org/r/20250829195525.721664-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 157ae5ffd7 ]
Fix a potential deadlock bug. Observe that in the mtk-cqdma.c
file, functions like mtk_cqdma_issue_pending() and
mtk_cqdma_free_active_desc() properly acquire the pc lock before the vc
lock when handling pc and vc fields. However, mtk_cqdma_tx_status()
violates this order by first acquiring the vc lock before invoking
mtk_cqdma_find_active_desc(), which subsequently takes the pc lock. This
reversed locking sequence (vc → pc) contradicts the established
pc → vc order and creates deadlock risks.
Fix the issue by moving the vc lock acquisition code from
mtk_cqdma_find_active_desc() to mtk_cqdma_tx_status(). Ensure the pc lock
is acquired before the vc lock in the calling function to maintain correct
locking hierarchy. Note that since mtk_cqdma_find_active_desc() is a
static function with only one caller (mtk_cqdma_tx_status()), this
modification safely eliminates the deadlock possibility without affecting
other components.
This possible bug is found by an experimental static analysis tool
developed by our team. This tool analyzes the locking APIs to extract
function pairs that can be concurrently executed, and then analyzes the
instructions in the paired functions to identify possible concurrency bugs
including deadlocks, data races and atomicity violations.
Fixes: b1f01e48df ("dmaengine: mediatek: Add MediaTek Command-Queue DMA controller for MT6765 SoC")
Cc: stable@vger.kernel.org
Signed-off-by: Qiu-ji Chen <chenqiuji666@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250508073634.3719-1-chenqiuji666@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fa17ff8e32 ]
In order to get working interrupts, a low offset value needs to be
configured. The minimum value for it is 20 Celsius, which is what is
configured when there's no lower thermal trip (ie the thermal core
passes -INT_MAX as low trip temperature). However, when the temperature
gets that low and fluctuates around that value it causes an interrupt
storm.
Prevent that interrupt storm by not enabling the low offset interrupt if
the low threshold is the minimum one.
Cc: stable@vger.kernel.org
Fixes: 77354eaef8 ("thermal/drivers/mediatek/lvts_thermal: Don't leave threshold zeroed")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20250113-mt8192-lvts-filtered-suspend-fix-v2-3-07a25200c7c6@collabora.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ Adapted interrupt mask definitions ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3576889d8 ]
For !CONFIG_SPARSEMEM_VMEMMAP, memmap page accounting is currently done
upfront in sparse_buffer_init(). However, sparse_buffer_alloc() may
return NULL in failure scenario.
Also, memmap pages may be allocated either from the memblock allocator
during early boot or from the buddy allocator. When removed via
arch_remove_memory(), accounting of memmap pages must reflect the original
allocation source.
To ensure correctness:
* Account memmap pages after successful allocation in sparse_init_nid()
and section_activate().
* Account memmap pages in section_deactivate() based on allocation
source.
Link: https://lkml.kernel.org/r/20250807183545.1424509-1-sumanthk@linux.ibm.com
Fixes: 15995a3524 ("mm: report per-page metadata information")
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Suggested-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Wei Yang <richard.weiyang@gmail.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to commit 09c6304e38 ("kasan: test: fix compatibility with
FORTIFY_SOURCE") the kernel is panicing in kasan_string().
This is due to the `src` and `ptr` not being hidden from the optimizer
which would disable the runtime fortify string checker.
Call trace:
__fortify_panic+0x10/0x20 (P)
kasan_strings+0x980/0x9b0
kunit_try_run_case+0x68/0x190
kunit_generic_run_threadfn_adapter+0x34/0x68
kthread+0x1c4/0x228
ret_from_fork+0x10/0x20
Code: d503233f a9bf7bfd 910003fd 9424b243 (d4210000)
---[ end trace 0000000000000000 ]---
note: kunit_try_catch[128] exited with irqs disabled
note: kunit_try_catch[128] exited with preempt_count 1
# kasan_strings: try faulted: last
** replaying previous printk message **
# kasan_strings: try faulted: last line seen mm/kasan/kasan_test_c.c:1600
# kasan_strings: internal error occurred preventing test case from running: -4
Link: https://lkml.kernel.org/r/20250801120236.2962642-1-yeoreum.yun@arm.com
Fixes: 73228c7ecc ("KASAN: port KASAN Tests to KUnit")
Signed-off-by: Yeoreum Yun <yeoreum.yun@arm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: <stable@vger.kernel.org>
[ One less test in older trees ]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ef5c4e4db ]
Nouveau has code that when it gets an IRQ with no allowed handler
it disables it to avoid storms.
However with nonstall interrupts, we often disable them from
the drm driver, but still request their emission via the push submission.
Just don't disable nonstall irqs ever in normal operation, the
event handling code will filter them out, and the driver will
just enable/disable them at load time.
This fixes timeouts we've been seeing on/off for a long time,
but they became a lot more noticeable on Blackwell.
This doesn't fix all of them, there is a subsequent fence emission
fix to fix the last few.
Fixes: 3ebd64aa3c ("drm/nouveau/intr: support multiple trees, and explicit interfaces")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://lore.kernel.org/r/20250829021633.1674524-1-airlied@gmail.com
[ Fix a typo and a minor checkpatch.pl warning; remove "v2" from commit
subject. - Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
[ Apply to drivers/gpu/drm/nouveau/nvkm/engine/fifo/r535.c ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4efccec8d ]
object_err() reports details of an object for further debugging, such as
the freelist pointer, redzone, etc. However, if the pointer is invalid,
attempting to access object metadata can lead to a crash since it does
not point to a valid object.
One known path to the crash is when alloc_consistency_checks()
determines the pointer to the allocated object is invalid because of a
freelist corruption, and calls object_err() to report it. The debug code
should report and handle the corruption gracefully and not crash in the
process.
In case the pointer is NULL or check_valid_pointer() returns false for
the pointer, only print the pointer value and skip accessing metadata.
Fixes: 81819f0fc8 ("SLUB core")
Cc: <stable@vger.kernel.org>
Signed-off-by: Li Qiong <liqiong@nfschina.com>
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4b183dd935 ]
slab_err() has variadic printf arguments but instead of passing them to
slab_bug() it does vsnprintf() to a buffer and passes %s, buf.
To allow passing them directly, turn slab_bug() to __slab_bug() with a
va_list parameter, and slab_bug() a wrapper with fmt, ... parameters.
Then slab_err() can call __slab_bug() without the intermediate buffer.
Also constify fmt everywhere, which also simplifies object_err()'s
call to slab_bug().
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Stable-dep-of: b4efccec8d ("mm/slub: avoid accessing metadata when pointer is invalid in object_err()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f6f32b14a ]
If a slab object is corrupted or an error occurs in its internal
validation, continuing after restoration may cause other side effects.
At this point, it is difficult to debug because the problem occurred in
the past. It is useful to use WARN() to catch errors at the point of
issue because WARN() could trigger panic for system debugging when
panic_on_warn is enabled. WARN() is added where to detect the error on
slab_err and object_err.
It makes sense to only do the WARN() after printing the logs. slab_err
is splited to __slab_err that calls the WARN() and it is called after
printing logs.
Signed-off-by: Hyesoo Yu <hyesoo.yu@samsung.com>
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Stable-dep-of: b4efccec8d ("mm/slub: avoid accessing metadata when pointer is invalid in object_err()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ed5ec2e952 ]
Previously, the restore occurred after printing the object in slub.
After commit 47d911b02c ("slab: make check_object() more consistent"),
the bytes are printed after the restore. This information about the bytes
before the restore is highly valuable for debugging purpose.
For instance, in a event of cache issue, it displays byte patterns
by breaking them down into 64-bytes units. Without this information,
we can only speculate on how it was broken. Hence the corrupted regions
should be printed prior to the restoration process. However if an object
breaks in multiple places, the same log may be output multiple times.
Therefore the slub log is reported only once to prevent redundant printing,
by sending a parameter indicating whether an error has occurred previously.
Signed-off-by: Hyesoo Yu <hyesoo.yu@samsung.com>
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Stable-dep-of: b4efccec8d ("mm/slub: avoid accessing metadata when pointer is invalid in object_err()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6130825f34 upstream.
In clustermd, separate write-intent-bitmaps are used for each cluster
node:
0 4k 8k 12k
-------------------------------------------------------------------
| idle | md super | bm super [0] + bits |
| bm bits[0, contd] | bm super[1] + bits | bm bits[1, contd] |
| bm super[2] + bits | bm bits [2, contd] | bm super[3] + bits |
| bm bits [3, contd] | | |
So in node 1, pg_index in __write_sb_page() could equal to
bitmap->storage.file_pages. Then bitmap_limit will be calculated to
0. md_super_write() will be called with 0 size.
That means the first 4k sb area of node 1 will never be updated
through filemap_write_page().
This bug causes hang of mdadm/clustermd_tests/01r1_Grow_resize.
Here use (pg_index % bitmap->storage.file_pages) to make calculation
of bitmap_limit correct.
Fixes: ab99a87542 ("md/md-bitmap: fix writing non bitmap pages")
Signed-off-by: Su Yue <glass.su@suse.com>
Reviewed-by: Heming Zhao <heming.zhao@suse.com>
Link: https://lore.kernel.org/linux-raid/20250303033918.32136-1-glass.su@suse.com
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0032c99e83 upstream.
When delete l3s ipvlan:
ip link del link eth0 ipvlan1 type ipvlan mode l3s
This may cause a null pointer dereference:
Call trace:
ip_rcv_finish+0x48/0xd0
ip_rcv+0x5c/0x100
__netif_receive_skb_one_core+0x64/0xb0
__netif_receive_skb+0x20/0x80
process_backlog+0xb4/0x204
napi_poll+0xe8/0x294
net_rx_action+0xd8/0x22c
__do_softirq+0x12c/0x354
This is because l3mdev_l3_rcv() visit dev->l3mdev_ops after
ipvlan_l3s_unregister() assign the dev->l3mdev_ops to NULL. The process
like this:
(CPU1) | (CPU2)
l3mdev_l3_rcv() |
check dev->priv_flags: |
master = skb->dev; |
|
| ipvlan_l3s_unregister()
| set dev->priv_flags
| dev->l3mdev_ops = NULL;
|
visit master->l3mdev_ops |
To avoid this by do not set dev->l3mdev_ops when unregister l3s ipvlan.
Suggested-by: David Ahern <dsahern@kernel.org>
Fixes: c675e06a98 ("ipvlan: decouple l3s mode dependencies from other modes")
Signed-off-by: Wang Liang <wangliang74@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250321090353.1170545-1-wangliang74@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02aae8e2f9 upstream.
With previous patch "wifi: ath11k: move update channel list from update
reg worker to reg notifier", ath11k_reg_update_chan_list() will be
called during reg_process_self_managed_hint().
reg_process_self_managed_hint() will hold rtnl_lock all the time.
But ath11k_reg_update_chan_list() may increase the occupation time of
rtnl_lock, because when wait flag is set, wait_for_completion_timeout()
will be called during 11d/hw scan.
Should minimize the occupation time of rtnl_lock as much as possible
to avoid interfering with rest of the system. So move the update channel
list operation to a new worker, so that wait_for_completion_timeout()
won't be called and will not increase the occupation time of rtnl_lock.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Co-developed-by: Kang Yang <quic_kangyang@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250117061737.1921-3-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 933ab187e6 upstream.
Currently when ath11k gets a new channel list, it will be processed
according to the following steps:
1. update new channel list to cfg80211 and queue reg_work.
2. cfg80211 handles new channel list during reg_work.
3. update cfg80211's handled channel list to firmware by
ath11k_reg_update_chan_list().
But ath11k will immediately execute step 3 after reg_work is just
queued. Since step 2 is asynchronous, cfg80211 may not have completed
handling the new channel list, which may leading to an out-of-bounds
write error:
BUG: KASAN: slab-out-of-bounds in ath11k_reg_update_chan_list
Call Trace:
ath11k_reg_update_chan_list+0xbfe/0xfe0 [ath11k]
kfree+0x109/0x3a0
ath11k_regd_update+0x1cf/0x350 [ath11k]
ath11k_regd_update_work+0x14/0x20 [ath11k]
process_one_work+0xe35/0x14c0
Should ensure step 2 is completely done before executing step 3. Thus
Wen raised patch[1]. When flag NL80211_REGDOM_SET_BY_DRIVER is set,
cfg80211 will notify ath11k after step 2 is done.
So enable the flag NL80211_REGDOM_SET_BY_DRIVER then cfg80211 will
notify ath11k after step 2 is done. At this time, there will be no
KASAN bug during the execution of the step 3.
[1] https://patchwork.kernel.org/project/linux-wireless/patch/20230201065313.27203-1-quic_wgong@quicinc.com/
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: f45cb6b29c ("wifi: ath11k: avoid deadlock during regulatory update in ath11k_regd_update()")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250117061737.1921-2-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce2f26e737 upstream.
Presently we always BUG_ON if trying to start a transaction on a journal marked
with JBD2_UNMOUNT, since this should never happen. However, while ltp running
stress tests, it was observed that in case of some error handling paths, it is
possible for update_super_work to start a transaction after the journal is
destroyed eg:
(umount)
ext4_kill_sb
kill_block_super
generic_shutdown_super
sync_filesystem /* commits all txns */
evict_inodes
/* might start a new txn */
ext4_put_super
flush_work(&sbi->s_sb_upd_work) /* flush the workqueue */
jbd2_journal_destroy
journal_kill_thread
journal->j_flags |= JBD2_UNMOUNT;
jbd2_journal_commit_transaction
jbd2_journal_get_descriptor_buffer
jbd2_journal_bmap
ext4_journal_bmap
ext4_map_blocks
...
ext4_inode_error
ext4_handle_error
schedule_work(&sbi->s_sb_upd_work)
/* work queue kicks in */
update_super_work
jbd2_journal_start
start_this_handle
BUG_ON(journal->j_flags &
JBD2_UNMOUNT)
Hence, introduce a new mount flag to indicate journal is destroying and only do
a journaled (and deferred) update of sb if this flag is not set. Otherwise, just
fallback to an un-journaled commit.
Further, in the journal destroy path, we have the following sequence:
1. Set mount flag indicating journal is destroying
2. force a commit and wait for it
3. flush pending sb updates
This sequence is important as it ensures that, after this point, there is no sb
update that might be journaled so it is safe to update the sb outside the
journal. (To avoid race discussed in 2d01ddc866)
Also, we don't need a similar check in ext4_grp_locked_error since it is only
called from mballoc and AFAICT it would be always valid to schedule work here.
Fixes: 2d01ddc866 ("ext4: save error info to sb through journal if available")
Reported-by: Mahesh Kumar <maheshkumar657g@gmail.com>
Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/9613c465d6ff00cd315602f99283d5f24018c3f7.1742279837.git.ojaswin@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a02a6204c upstream.
Define an ext4 wrapper over jbd2_journal_destroy to make sure we
have consistent behavior during journal destruction. This will also
come useful in the next patch where we add some ext4 specific logic
in the destroy path.
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://patch.msgid.link/c3ba78c5c419757e6d5f2d8ebb4a8ce9d21da86a.1742279837.git.ojaswin@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fa31c4992 upstream.
RAID layers don't implement proper non-blocking semantics for
REQ_NOWAIT, making the flag potentially misleading when propagated
to member disks.
This patch clear REQ_NOWAIT from cloned bios in raid1/raid10. Retain
original bio's REQ_NOWAIT flag for upper layer error handling.
Maybe we can implement non-blocking I/O handling mechanisms within
RAID in future work.
Fixes: 9f346f7d4e ("md/raid1,raid10: don't handle IO error for REQ_RAHEAD and REQ_NOWAIT")
Signed-off-by: Zheng Qixing <zhengqixing@huawei.com>
Link: https://lore.kernel.org/linux-raid/20250702102341.1969154-1-zhengqixing@huaweicloud.com
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f346f7d4e upstream.
IO with REQ_RAHEAD or REQ_NOWAIT can fail early, even if the storage medium
is fine, hence record badblocks or remove the disk from array does not
make sense.
This problem if found by lvm2 test lvcreate-large-raid, where dm-zero
will fail read ahead IO directly.
Fixes: e879a0d9cb ("md/raid1,raid10: don't ignore IO flags")
Reported-and-tested-by: Mikulas Patocka <mpatocka@redhat.com>
Closes: https://lore.kernel.org/all/34fa755d-62c8-4588-8ee1-33cb1249bdf2@redhat.com/
Link: https://lore.kernel.org/linux-raid/20250527081407.3004055-1-yukuai1@huaweicloud.com
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e879a0d9cb upstream.
If blk-wbt is enabled by default, it's found that raid write performance
is quite bad because all IO are throttled by wbt of underlying disks,
due to flag REQ_IDLE is ignored. And turns out this behaviour exist since
blk-wbt is introduced.
Other than REQ_IDLE, other flags should not be ignored as well, for
example REQ_META can be set for filesystems, clearing it can cause priority
reverse problems; And REQ_NOWAIT should not be cleared as well, because
io will wait instead of failing directly in underlying disks.
Fix those problems by keep IO flags from master bio.
Fises: f51d46d0e7 ("md: add support for REQ_NOWAIT")
Fixes: e34cbd3074 ("blk-wbt: add general throttling mechanism")
Fixes: 5404bc7a87 ("[PATCH] Allow file systems to differentiate between data and meta reads")
Link: https://lore.kernel.org/linux-raid/20250227121657.832356-1-yukuai1@huaweicloud.com
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
[ Harshit: Resolve conflicts due to missing commit: f2a38abf5f
("md/raid1: Atomic write support") and commit: a1d9b4fd42
("md/raid10: Atomic write support") in 6.12.y, we don't have Atomic
writes feature in 6.12.y ]
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1237c2d4a8 upstream.
BCM63xx internal switches do not support EEE, but provide multiple RGMII
ports where external PHYs may be connected. If one of these PHYs are EEE
capable, we may try to enable EEE for the MACs, which then hangs the
system on access of the (non-existent) EEE registers.
Fix this by checking if the switch actually supports EEE before
attempting to configure it.
Fixes: 22256b0afb ("net: dsa: b53: Move EEE functions to b53")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20250602193953.1010487-2-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c86692fc2c upstream.
Implement the .support_eee() method to indicate that EEE is not
supported by two switch variants, rather than making these checks in
the .set_mac_eee() and .get_mac_eee() methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14E-006cZU-Nc@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99379f5872 upstream.
Provide a trivial implementation for the .support_eee() method which
switch drivers can use to simply indicate that they support EEE on
all their user ports.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL149-006cZJ-JJ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ Harshit: Resolve contextual conflicts due to missing commit:
5397706165 ("net: dsa: remove obsolete phylink dsa_switch operations")
and commit: ecb595ebba ("net: dsa: remove
dsa_port_phylink_mac_select_pcs()") in 6.12.y ]
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9723a77318 upstream.
Add a hook to determine whether the switch supports EEE. This will
return false if the switch does not, or true if it does. If the
method is not implemented, we assume (currently) that the switch
supports EEE.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL144-006cZD-El@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f282cdc1d upstream.
may_decode_fh() is calling has_locked_children() while holding no locks.
That's an oopsable race...
The rest of the callers are safe since they are holding namespace_sem and
are guaranteed a positive refcount on the mount in question.
Rename the current has_locked_children() to __has_locked_children(), make
it static and switch the fs/namespace.c users to it.
Make has_locked_children() a wrapper for __has_locked_children(), calling
the latter under read_seqlock_excl(&mount_lock).
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Fixes: 620c266f39 ("fhandle: relax open_by_handle_at() permission checks")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ Harshit: Resolved conflicts due to missing commit:
db04662e2f ("fs: allow detached mounts in clone_private_mount()") in
linux-6.12.y ]
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca47c44d36 upstream.
Add missing IDs for LAN8651 devices, which are also defined in the
DT bindings.
Fixes: 5cd2340cb6 ("microchip: lan865x: add driver support for Microchip's LAN865X MAC-PHY")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: stable@kernel.org
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250827115341.34608-4-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7217963eb upstream.
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from spi_device_id table. While at this, fix
the misleading variable name (spidev is unrelated to this driver).
Fixes: 5cd2340cb6 ("microchip: lan865x: add driver support for Microchip's LAN865X MAC-PHY")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: stable@kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250827115341.34608-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7195a3d67 upstream.
Correct the Mode Control Register (MODCTRL) offset for RZ/N MIIC.
According to the R-IN Engine and Ethernet Peripherals Manual (Rev.1.30)
[0], Table 10.1 "Ethernet Accessory Register List", MODCTRL is at offset
0x8, not 0x20 as previously defined.
Offset 0x20 actually maps to the Port Trigger Control Register (PTCTRL),
which controls PTP_MODE[3:0] and RGMII_CLKSEL[4]. Using this incorrect
definition prevented the driver from configuring the SW_MODE[4:0] bits
in MODCTRL, which control the internal connection of Ethernet ports. As
a result, the MIIC could not be switched into the correct mode, leading
to link setup failures and non-functional Ethernet ports on affected
systems.
[0] https://www.renesas.com/en/document/mah/rzn1d-group-rzn1s-group-rzn1l-group-users-manual-r-engine-and-ethernet-peripherals?r=1054571
Fixes: 7dc54d3b8d ("net: pcs: add Renesas MII converter driver")
Cc: stable@kernel.org
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://patch.msgid.link/20250901112019.16278-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90fb7db49c upstream.
Fix a possible heap overflow in e1000_set_eeprom function by adding
input validation for the requested length of the change in the EEPROM.
In addition, change the variable type from int to size_t for better
code practices and rearrange declarations to RCT.
Cc: stable@vger.kernel.org
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Co-developed-by: Mikael Wessel <post@mikaelkw.online>
Signed-off-by: Mikael Wessel <post@mikaelkw.online>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70bccd9855 upstream.
There can be a NULL pointer dereference bug here. NULL is passed to
__cifs_sfu_make_node without checks, which passes it unchecked to
cifs_strndup_to_utf16, which in turn passes it to
cifs_local_to_utf16_bytes where '*from' is dereferenced, causing a crash.
This patch adds a check for NULL 'src' in cifs_strndup_to_utf16 and
returns NULL early to prevent dereferencing NULL pointer.
Found by Linux Verification Center (linuxtesting.org) with SVACE
Signed-off-by: Makar Semyonov <m.semenov@tssltd.ru>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d77b6ff0ce upstream.
batadv_nc_skb_decode_packet() trusts coded_len and checks only against
skb->len. XOR starts at sizeof(struct batadv_unicast_packet), reducing
payload headroom, and the source skb length is not verified, allowing an
out-of-bounds read and a small out-of-bounds write.
Validate that coded_len fits within the payload area of both destination
and source sk_buffs before XORing.
Fixes: 2df5278b02 ("batman-adv: network coding - receive coded packets and decode them")
Cc: stable@vger.kernel.org
Reported-by: Stanislav Fort <disclosure@aisle.com>
Signed-off-by: Stanislav Fort <stanislav.fort@aisle.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dba9a45c3 upstream.
Fix a use-after-free window by correcting the buffer release sequence in
the deferred receive path. The code freed the RQ buffer first and only
then cleared the context pointer under the lock. Concurrent paths (e.g.,
ABTS and the repost path) also inspect and release the same pointer under
the lock, so the old order could lead to double-free/UAF.
Note that the repost path already uses the correct pattern: detach the
pointer under the lock, then free it after dropping the lock. The
deferred path should do the same.
Fixes: 472e146d1c ("scsi: lpfc: Correct upcalling nvmet_fc transport during io done downcall")
Cc: stable@vger.kernel.org
Signed-off-by: John Evans <evans1210144@gmail.com>
Link: https://lore.kernel.org/r/20250828044008.743-1-evans1210144@gmail.com
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c96f86217b upstream.
Prevents instant wakeup ~1s after suspend.
It seems to be kernel/system dependent if the IRQ actually manages to wake
the system every time or if it gets ignored (and everything works as
expected).
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250827131424.16436-1-wse@tuxedocomputers.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ebf766c35 upstream.
[Why&How]
ON DCN314, clearing DPP SW structure without power gating it can cause a
double cursor in full screen with non-native scaling.
A W/A that clears CURSOR0_CONTROL cursor_enable flag if
dcn10_plane_atomic_power_down is called and DPP power gating is disabled.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4168
Reviewed-by: Sun peng (Leo) Li <sunpeng.li@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 645f74f1dc)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71403f58b4 upstream.
We already disable the audio pins in hw_fini so
there is no need to do it again in sw_fini.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4481
Cc: oushixiong <oushixiong1025@163.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 5eeb16ca72)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3852ae310 upstream.
There is no guarantee that spi_setup succeed, so properly handle
the error case.
Fixes: aa58bec064 ("net: ethernet: oa_tc6: implement register write operation")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: stable@kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250827115341.34608-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
