There are two rings involved in the Copy Engine (CE) receive path
handling, the CE status (STS) ring and the CE destination (DST) ring.
Each time CE hardware needs to send an event (e.g. WMI event) to host,
CE hardware finds a buffer (to which the tail pointer (TP) points) in
DST ring and fills it with payload, then hardware fills meta data in
STS ring and fires interrupt to host. Please note the TP of DST ring is
expected to be advanced by CE hardware before interrupting host. While
handling the interrupt, host finds that DST ring buffers are used hence
increases rx_buf_needed to record the number of buffers to be replenished.
Note before that, host compares TP and head pointer (HP) of DST ring to
see if there is available space. Normally rx_buf_needed simply equals
available space. But sometimes CE hardware doesn't (for whatever reason)
update TP timely, making the comparison fails, then enqueue is cancelled
and a warning is logged.
However even enqueue fails this time, rx_buf_needed still records the
numbers of needed buffers. Later when TP gets updated correctly, the
missing buffer will be eventually replenished. And there is no doubt on
the late update, it always comes (or lots of such warnings should be seen).
Since this won't cause any functional issue, downgrade logging level to
avoid misleading.
Compile tested only.
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250815-ath-dont-warn-on-ce-enqueue-fail-v1-3-f955ddc3ba7a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ATH12K_DBG_AHB is used for CE logging which is not proper. Add
ATH12K_DBG_CE and replace ATH12K_DBG_AHB with it.
Compile tested only.
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250815-ath-dont-warn-on-ce-enqueue-fail-v1-2-f955ddc3ba7a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
There are two rings involved in the Copy Engine (CE) receive path
handling, the CE status (STS) ring and the CE destination (DST) ring.
Each time CE hardware needs to send an event (e.g. WMI event) to host,
CE hardware finds a buffer (to which the tail pointer (TP) points) in
DST ring and fills it with payload, then hardware fills meta data in
STS ring and fires interrupt to host. Please note the TP of DST ring is
expected to be advanced by CE hardware before interrupting host. While
handling the interrupt, host finds that DST ring buffers are used hence
increases rx_buf_needed to record the number of buffers to be replenished.
Note before that, host compares TP and head pointer (HP) of DST ring to
see if there is available space. Normally rx_buf_needed simply equals
available space. But sometimes CE hardware doesn't (for whatever reason)
update TP timely, making the comparison fails, then enqueue is cancelled
and a warning is logged:
ath11k_pci 0000:02:00.0: failed to enqueue rx buf: -28
However even enqueue fails this time, rx_buf_needed still records the
numbers of needed buffers. Later when TP gets updated correctly, the
missing buffer will be eventually replenished. And there is no doubt on
the late update, it always comes (or lots of such warnings should be seen).
Since this won't cause any functional issue, downgrade logging level to
avoid misleading.
Compile tested only.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220269
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250815-ath-dont-warn-on-ce-enqueue-fail-v1-1-f955ddc3ba7a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_dp_rx_h_ppdu() determines the band and frequency
based on the channel number and center frequency from the RX descriptor's
PHY metadata. However, in rare cases, it is observed that frequency
retrieved from the metadata may be invalid or unexpected especially for
6 GHz frames.
This can result in a NULL sband, which prevents proper frequency assignment
in rx_status and potentially leading to incorrect RX packet classification.
To fix this potential issue, add a fallback mechanism that uses
ar->rx_channel to populate the band and frequency when the derived
sband is invalid or missing.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vinith Kumar R <quic_vinithku@quicinc.com>
Signed-off-by: Vinith Kumar R <quic_vinithku@quicinc.com>
Signed-off-by: Aishwarya R <aishwarya.r@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250723190651.699828-1-aishwarya.r@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, host fetches combined rssi from rssi_comb in struct
hal_rx_phyrx_rssi_legacy_info.
rssi_comb is 8th to 15th bits of the second to last variable.
rssi_comb_ppdu is the 0th to 7th of the last variable.
When bandwidth = 20MHz, rssi_comb = rssi_comb_ppdu. But when bandwidth >
20MHz, rssi_comb < rssi_comb_ppdu because rssi_comb only includes power
of primary 20 MHz while rssi_comb_ppdu includes power of active
RUs/subchannels. So should fetch combined rssi from rssi_comb_ppdu.
Also related macro definitions are too long, rename them.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250722095934.67-4-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Current monitor mode will parse TLV HAL_PHYRX_OTHER_RECEIVE_INFO with
struct hal_phyrx_common_user_info.
Obviously, they do not match. The original intention here was to parse
HAL_PHYRX_COMMON_USER_INFO. So fix it by correctly parsing
HAL_PHYRX_COMMON_USER_INFO instead.
Also add LTF parsing and report to radiotap along with GI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d939919a36 ("wifi: ath12k: Add HAL_PHYRX_OTHER_RECEIVE_INFO TLV parsing support")
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250722095934.67-3-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently host will add ATH12K_DEFAULT_NOISE_FLOOR to rssi_comb to
convert RSSI from dB to dBm.
For WCN7850, this conversion is unnecessary because the RSSI value is
already reported in dBm units.
No longer convert for those firmware that already support dBM conversion.
This patch won't affect QCN chips.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250722095934.67-2-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath12k_mac_parse_tx_pwr_env(), for the non-PSD case num_pwr_levels is
limited by ATH12K_NUM_PWR_LEVELS which is 16:
if (tpc_info->num_pwr_levels > ATH12K_NUM_PWR_LEVELS)
tpc_info->num_pwr_levels = ATH12K_NUM_PWR_LEVELS;
Then it is used to iterate entries in local_non_psd->power[] and
reg_non_psd->power[]:
for (i = 0; i < tpc_info->num_pwr_levels; i++) {
tpc_info->tpe[i] = min(local_non_psd->power[i],
reg_non_psd->power[i]) / 2;
Since the two array are of size 5, Smatch warns:
drivers/net/wireless/ath/ath12k/mac.c:9812
ath12k_mac_parse_tx_pwr_env() error: buffer overflow 'local_non_psd->power' 5 <= 15
drivers/net/wireless/ath/ath12k/mac.c:9812
ath12k_mac_parse_tx_pwr_env() error: buffer overflow 'reg_non_psd->power' 5 <= 15
This is a false positive as there is already implicit limitation:
tpc_info->num_pwr_levels = max(local_non_psd->count,
reg_non_psd->count);
meaning it won't exceed 5.
However, to make robot happy, add explicit limit there.
Also add the same to the PSD case, although no warning due to
ATH12K_NUM_PWR_LEVELS equals IEEE80211_TPE_PSD_ENTRIES_320MHZ.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Fixes: cccbb9d0dd ("wifi: ath12k: add parse of transmit power envelope element")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202505180703.Kr9OfQRP-lkp@intel.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250804-ath12k-fix-smatch-warning-on-6g-vlp-v1-2-56f1e54152ab@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, at the end of ath12k_mac_fill_reg_tpc_info(), the
reg_tpc_info struct is populated, including the following:
reg_tpc_info->is_psd_power = is_psd_power;
reg_tpc_info->eirp_power = eirp_power;
Kernel test robot complains on uninitialized symbol:
drivers/net/wireless/ath/ath12k/mac.c:10069
ath12k_mac_fill_reg_tpc_info() error: uninitialized symbol 'eirp_power'
This is because there are some code paths that never set eirp_power, so
the assignment of reg_tpc_info->eirp_power can come from an
uninitialized variable. Functionally this is OK since the eirp_power
only has meaning when is_psd_power is true, and all code paths which set
is_psd_power to true also set eirp_power. However, to keep the robot
happy, always initialize eirp_power before use.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Fixes: aeda163bb0 ("wifi: ath12k: fill parameters for vdev set TPC power WMI command")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202505180927.tbNWr3vE-lkp@intel.com/
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250804-ath12k-fix-smatch-warning-on-6g-vlp-v1-1-56f1e54152ab@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, command to set RTS threshold makes changes to the threshold of
all radios in the multi-radio wiphy. But each radio in a multi-radio wiphy
can have different RTS threshold requirements.
To support this requirement, use the index of radio for which the RTS
threshold needs to be changed from mac80211 - radio_idx. Based on the value
passed, set the RTS threshold value for the corresponding radios. Following
are the possible values of radio_idx and the corresponding behavior in
multi-radio wiphys:
1. radio_idx is -1: consider RTS threshold as a global parameter, i.e.,
make changes to all the radios in a wiphy. If setting RTS threshold
fails for any radio, then the previous RTS threshold values of
respective radios will be restored.
2. radio_idx denotes a specific radio: make changes in RTS threshold to
that radio alone.
3. radio_idx is any other number: report it as an invalid number.
In case of single-radio wiphys, continue with the existing behavior, i.e.,
set the passed RTS threshold value to the radio present.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250826105714.1188131-1-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Implement get_pauseparam() and set_pauseparam() ethtool operations for
Sparx5 ports. This allows users to query and configure IEEE 802.3x
pause frame settings via:
ethtool -a ethX
ethtool -A ethX rx on|off tx on|off autoneg on|off
The driver delegates pause parameter handling to phylink through
phylink_ethtool_get_pauseparam() and phylink_ethtool_set_pauseparam().
The underlying configuration of pause frame generation and reception is
already implemented in the driver; this patch only wires it up to the
standard ethtool interface, making the feature accessible to userspace.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250917-802-3x-pause-v1-1-3d1565a68a96@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LAN969x switchdev support depends on the SparX-5 core,so make it selectable
for ARCH_LAN969X.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20250917110106.55219-1-robert.marko@sartura.hr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for fast link failure for lan8842, when this is enabled the
PHY will detect link down immediately (~1ms). The disadvantage of this
is that also small instability might be reported as link down.
Therefore add this feature as a tunable configuration and the user will
know when to enable or not. By default it is not enabled.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250917104630.3931969-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When adding new VM MAC, driver checks only *active* filters in
vsi->mac_filter_hash. Each MAC, even in non-active state is using resources.
To determine number of MACs VM uses, count VSI filters in *any* state.
Add i40e_count_all_filters() to simply count all filters, and rename
i40e_count_filters() to i40e_count_active_filters() to avoid ambiguity.
Fixes: cfb1d572c9 ("i40e: Add ensurance of MacVlan resources for every trusted VF")
Cc: stable@vger.kernel.org
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ITR index (itr_idx) is only 2 bits wide. When constructing the
register value for QINT_RQCTL, all fields are ORed together. Without
masking, higher bits from itr_idx may overwrite adjacent fields in the
register.
Apply I40E_QINT_RQCTL_ITR_INDX_MASK to ensure only the intended bits are
set.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Cc: stable@vger.kernel.org
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is no check for max filters that VF can request. Add it.
Fixes: e284fc2804 ("i40e: Add and delete cloud filter")
Cc: stable@vger.kernel.org
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
VF state I40E_VF_STATE_ACTIVE is not the only state in which
VF is actually active so it should not be used to determine
if a VF is allowed to obtain resources.
Use I40E_VF_STATE_RESOURCES_LOADED that is set only in
i40e_vc_get_vf_resources_msg() and cleared during reset.
Fixes: 61125b8be8 ("i40e: Fix failed opcode appearing if handling messages from VF")
Cc: stable@vger.kernel.org
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ensure idx is within range of active/initialized TCs when iterating over
vf->ch[idx] in i40e_vc_config_queues_msg().
Fixes: c27eac4816 ("i40e: Enable ADq and create queue channel/s on VF")
Cc: stable@vger.kernel.org
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Kamakshi Nellore <nellorex.kamakshi@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ensure idx is within range of active/initialized TCs when iterating over
vf->ch[idx] in i40e_validate_queue_map().
Fixes: c27eac4816 ("i40e: Enable ADq and create queue channel/s on VF")
Cc: stable@vger.kernel.org
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Kamakshi Nellore <nellorex.kamakshi@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The `ring_len` parameter provided by the virtual function (VF)
is assigned directly to the hardware memory context (HMC) without
any validation.
To address this, introduce an upper boundary check for both Tx and Rx
queue lengths. The maximum number of descriptors supported by the
hardware is 8k-32.
Additionally, enforce alignment constraints: Tx rings must be a multiple
of 8, and Rx rings must be a multiple of 32.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Cc: stable@vger.kernel.org
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a PHY is halted (e.g. `ip link set dev lan2 down`), several
fields in struct phy_device may still reflect the last active
connection. This leads to ethtool showing stale values even though
the link is down.
Reset selected fields in _phy_state_machine() when transitioning
to PHY_HALTED and the link was previously up:
- speed/duplex -> UNKNOWN, but only in autoneg mode (in forced mode
these fields carry configuration, not status)
- master_slave_state -> UNKNOWN if previously supported
- mdix -> INVALID (state only, same meaning as "unknown")
- lp_advertising -> always cleared
The cleanup is skipped if the PHY is in PHY_ERROR state, so the
last values remain available for diagnostics.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250917094751.2101285-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CPTS module of CPSW supports hardware timestamping of PTPv1 packets.Update
the "hwtstamp_rx_filters" of CPSW driver to enable timestamping of received
PTPv1 packets. Also update the advertised capability to include PTPv1.
Signed-off-by: Vishnu Singh <v-singh1@ti.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://patch.msgid.link/20250917041455.1815579-1-v-singh1@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor regmap_irq declarations with REGMAP_IRQ_REG_LINE saves a few
lines on definitions.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Current implementation uses handle_post_irq to actually handle chgin
irq. This is not how things are meant to work in regmap-irq.
Remove handle_post_irq, and request a threaded interrupt for chgin.
Fixes: a6a494c8e3 ("power: supply: max77705: Add charger driver for Maxim 77705")
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add INPUT_CURRENT_LIMIT, CONSTANT_CHARGE_CURRENT properties as writeable
to be able to control input power consumption and charging speed.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Handle error, returned from register writes in init function.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Using regfields allows to cleanup masks and register offset definition,
allowing to access register info by it's functional name.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Kumar Kartikeya Dwivedi says:
====================
Update KF_RCU_PROTECTED
Currently, KF_RCU_PROTECTED only applies to iterator APIs and that too
in a convoluted fashion: the presence of this flag on the kfunc is used
to set MEM_RCU in iterator type, and the lack of RCU protection results
in an error only later, once next() or destroy() methods are invoked on
the iterator. While there is no bug, this is certainly a bit unintuitive,
and makes the enforcement of the flag iterator specific.
In the interest of making this flag useful for other upcoming kfuncs,
e.g. scx_bpf_cpu_curr() [0][1], add enforcement for invoking the kfunc
in an RCU critical section in general.
In addition to this, the aforementioned kfunc also needs to return an
RCU protected pointer, which currently has no generic kfunc flag or
annotation. Add such a flag as well while we are at it.
[0]: https://lore.kernel.org/all/20250903212311.369697-3-christian.loehle@arm.com
[1]: https://lore.kernel.org/all/20250909195709.92669-1-arighi@nvidia.com
Changelog:
----------
v2 -> v3
v2: https://lore.kernel.org/bpf/20250917032014.4060112-1-memxor@gmail.com
* Add back lost hunk reworking documentation for KF_RCU_PROTECTED.
v1 -> v2
v1: https://lore.kernel.org/bpf/20250915024731.1494251-1-memxor@gmail.com
* Drop KF_RET_RCU and fold change into KF_RCU_PROTECTED. (Andrea, Alexei)
* Update tests for non-struct pointer return values with KF_RCU_PROTECTED.
====================
Link: https://patch.msgid.link/20250917032755.4068726-1-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a couple of test cases to ensure RCU protection is kicked in
automatically, and the return type is as expected.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20250917032755.4068726-3-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently, KF_RCU_PROTECTED only applies to iterator APIs and that too
in a convoluted fashion: the presence of this flag on the kfunc is used
to set MEM_RCU in iterator type, and the lack of RCU protection results
in an error only later, once next() or destroy() methods are invoked on
the iterator. While there is no bug, this is certainly a bit
unintuitive, and makes the enforcement of the flag iterator specific.
In the interest of making this flag useful for other upcoming kfuncs,
e.g. scx_bpf_cpu_curr() [0][1], add enforcement for invoking the kfunc
in an RCU critical section in general.
This would also mean that iterator APIs using KF_RCU_PROTECTED will
error out earlier, instead of throwing an error for lack of RCU CS
protection when next() or destroy() methods are invoked.
In addition to this, if the kfuncs tagged KF_RCU_PROTECTED return a
pointer value, ensure that this pointer value is only usable in an RCU
critical section. There might be edge cases where the return value is
special and doesn't need to imply MEM_RCU semantics, but in general, the
assumption should hold for the majority of kfuncs, and we can revisit
things if necessary later.
[0]: https://lore.kernel.org/all/20250903212311.369697-3-christian.loehle@arm.com
[1]: https://lore.kernel.org/all/20250909195709.92669-1-arighi@nvidia.com
Tested-by: Andrea Righi <arighi@nvidia.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20250917032755.4068726-2-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The PCIe spec uses "Requester ID", not "requestor ID". Follow the spec to
avoid confusion.
Signed-off-by: Emilio Perez <emiliopeju@gmail.com>
[bhelgaas: capitalize as a hint that the spec defines this]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250818023121.33427-1-emiliopeju@gmail.com
- Fix build in some RISC-V flavours
Some system calls only are available for the 64bit RISC-V machines.
#ifdef out the cases of clock_nanosleep and futex in the sleep monitor
if they are not supported by the architecture.
- Fix wrong cast, obsolete after refactoring
Use container_of() to get to the rv_monitor structure from the
enable_monitors_next() 'p' pointer. The assignment worked only because
the list field used happened to be the first field of the structure.
- Remove redundant include files
Some include files were listed twice. Remove the extra ones and sort
the includes.
- Fix missing unlock on failure
There was an error path that exited the rv_register_monitor() function
without releasing a lock. Change that to goto the lock release.
- Add Gabriele Monaco to be Runtime Verifier maintainer
Gabriele is doing most of the work on RV as well as collecting patches.
Add him to the maintainers file for Runtime Verification.
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCaMxsBRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qk5oAP4tlGnMBoLpZXVBpAubVUQOVRfQo5dI
ar9LpXdgnj4xQAEA9Q5uIvhCI/CMXTK98gFhR31p9O4Sqtn0JlCViBbVSQg=
=tUQG
-----END PGP SIGNATURE-----
Merge tag 'trace-rv-v6.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull runtime verifier fixes from Steven Rostedt:
- Fix build in some RISC-V flavours
Some system calls only are available for the 64bit RISC-V machines.
#ifdef out the cases of clock_nanosleep and futex in the sleep
monitor if they are not supported by the architecture.
- Fix wrong cast, obsolete after refactoring
Use container_of() to get to the rv_monitor structure from the
enable_monitors_next() 'p' pointer. The assignment worked only
because the list field used happened to be the first field of the
structure.
- Remove redundant include files
Some include files were listed twice. Remove the extra ones and sort
the includes.
- Fix missing unlock on failure
There was an error path that exited the rv_register_monitor()
function without releasing a lock. Change that to goto the lock
release.
- Add Gabriele Monaco to be Runtime Verifier maintainer
Gabriele is doing most of the work on RV as well as collecting
patches. Add him to the maintainers file for Runtime Verification.
* tag 'trace-rv-v6.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
rv: Add Gabriele Monaco as maintainer for Runtime Verification
rv: Fix missing mutex unlock in rv_register_monitor()
include/linux/rv.h: remove redundant include file
rv: Fix wrong type cast in enabled_monitors_next()
rv: Support systems with time64-only syscalls
prtd_tx and prtd_rx members are not used anymore and only qmc_chan
member remains so struct qmc_dai_chan has become pointless.
Use qmc_chan directly and drop struct qmc_dai_chan.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://patch.msgid.link/9c729bbd9f1b61120a09a87fb76176ef344c5153.1758209158.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
In non-interleaved mode, several QMC channels are used in sync.
More details can be found in commit 188d9cae54 ("ASoC: fsl:
fsl_qmc_audio: Add support for non-interleaved mode.")
At the time being, an interrupt is requested on each channel to
perform capture/playback completion, allthough the completion is
really performed only once all channels have completed their work.
This leads to a lot more interrupts than really needed. Looking at
/proc/interrupts shows ~3800 interrupts per second when using
4 capture and 4 playback devices with 5ms periods while
only 1600 (200 x 4 + 200 x 4) periods are processed during one second.
The QMC channels work in sync, the one started first is the one
finishing first and the one started last is the one finishing last,
so when the last one finishes it is guaranteed that the other ones are
finished as well. Therefore only request completion processing on the
last QMC channel.
On my board with the above exemple, on a kernel started with
'threadirqs' option, the QMC irq thread uses 16% CPU time with this
patch while it uses 26% CPU time without this patch.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://patch.msgid.link/bbd5167d190bbb45c3a4cd6ef2dece8817e0cc1e.1758209158.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
To reduce complexity of interrupt handling in following patch, ensure
audio channels are configured in the same order as timeslots on the
TDM bus. If we need a given ordering of audio sources in the audio
frame, it is possible to re-order codecs on the TDM bus, no need to
mix up timeslots in channels.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://patch.msgid.link/4ff40afdf3d032b05dd4af6c0f777d4d4b445a76.1758209158.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
When no post-completion processing is expected, don't waste time
handling useless interrupts.
Only set QMC_BD_[R/T]X_I when a completion function is passed in,
and perform seamless completion on submit for interruptless buffers.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://patch.msgid.link/40b41b53a26e77a50b3a5f68fcecc6f9a40a84b4.1758209158.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
During tests of another unrelated patch I was able to trigger this
error: Objects remaining on __kmem_cache_shutdown()
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Fixes: f198186aa9 ("CIFS: SMBD: Establish SMB Direct connection")
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Fix the file open check to decide whether or not silly-rename the file
in SMB2+.
Fixes: c5ea306558 ("smb: client: fix data loss due to broken rename(2)")
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Cc: Frank Sorenson <sorenson@redhat.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: linux-cifs@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Add changes to delay the allocation and setup of dports until when the
endpoint device is being probed. At this point, the CXL link is
established from endpoint to host bridge. Addresses issues seen on
some platforms when dports are probed earlier.
Link: https://lore.kernel.org/linux-cxl/20250829180928.842707-1-dave.jiang@intel.com/
This immutable branch between MFD and power-supply subsystem is
needed, since the change needs to touch drivers in both subsystems
at the same time.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=dRwQ
-----END PGP SIGNATURE-----
Merge tag 'ib-max77705-for-v6.17-signed'
Merge immutable branch between power-supply and MFD subsystem to
move the regmap register update from the max77976 charger
sub-device to the main MFD device.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch moves the port register setup to when the first dport appears
via the memdev probe path. At this point, the CXL link should be
established and the register access is expected to succeed. This change
addresses an error message observed when PCIe hotplug is enabled on
an Intel platform. The error messages "cxl portN: Couldn't locate the
CXL.cache and CXL.mem capability array header" is observed for the
host bridge (CHBCR) during cxl_acpi driver probe. If the cxl_acpi module
probe is running before the CXL link between the endpoint device and the
RP is established, then the platform may not have exposed DVSEC ID 3
and/or DVSEC ID 7 blocks which will trigger the error message. This
behavior is defined by the CXL spec r3.2 9.12.3 for RPs and DSPs, however
the Intel platform also added this behavior to the host bridge.
This change also needs the dport enumeration to be moved to the memdev
probe path in order to address the issue. This change is not a wholly
contained solution by itself.
[dj: Add missing var init during port alloc]
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Tested-by: Robert Richter <rrichter@amd.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Convert Rohm BU21013 I2C touchscreen controller device tree binding to
json-schema.
Additional changes:
- Replace <supply_name>-supply with avdd-supply to match example and
existing DTS.
- Add reset-gpios in the example because it is required.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250918153630.2535208-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Active discharge setting is a part of MFD top level i2c device, hence
cannot be controlled by charger. Writing to MAX77705_PMIC_REG_MAINCTRL1
register from charger driver is a mistake.
Move active discharge setting to MFD parent driver.
Fixes: a6a494c8e3 ("power: supply: max77705: Add charger driver for Maxim 77705")
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The devm_clk_get_enabled() function prepares and enables the
particular clock, which then automatically gets disabled and
unprepared on probe failure and on device removal.
Use that function instead of devm_clk_get() and remove the
clk_prepare_enable()/clk_disable_unprepare() calls in order
to simplify the code.
This also ensures that the clocks are handled in the correct
order during device removal.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20250916-qpic-snand-devm_clk_get_enabled-v1-1-09953493b7f1@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add OCT-DTR mode support in default, since flexspi do not supports
swapping bytes on a 16 bit boundary in OCT-DTR mode, so mark swap16
as false.
lx2160a do not support DQS, so add a quirk to disable DTR mode for this
platform.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250917-flexspi-ddr-v2-5-bb9fe2a01889@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
