The hypervisor assigns one pipe per partition for all sources and
assigns new pipe after migration. Also the partition ID that is
used by source as its target ID may be changed after the migration.
So disable hvpipe during SUSPEND event with ‘hvpipe enable’ system
parameter value = 0 and enable it after migration during RESUME
event with hvpipe enable’ system parameter value = 1.
The user space calls such as ioctl()/ read() / write() / poll()
returns -ENXIO between SUSPEND and RESUME events. The user space
process can close FD and reestablish connection with new FD after
migration if needed (Example: source IDs are changed).
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Tested-by: Shashank MS <shashank.gowda@in.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250909084402.1488456-10-haren@linux.ibm.com
The partition uses “Hypervisor Pipe OS Enablement Notification”
system parameter token (value = 64) to enable / disable hvpipe in
the hypervisor. Once hvpipe is enabled, the hypervisor notifies
OS if the payload is pending for that partition from any source.
This system parameter token takes 1 byte length of data with
1 = Enable and 0 = Disable.
Enable hvpipe in the hypervisor with ibm,set-system-parameter
RTAS after registering hvpipe event source interrupt.
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Tested-by: Shashank MS <shashank.gowda@in.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250909084402.1488456-9-haren@linux.ibm.com
The hypervisor signals the OS via a Hypervisor Pipe Event external
interrupt when data is available to be received from the pipe.
Then the OS should call RTAS check-exception and provide the input
Event Mask as defined for the ‘ibm,hvpipe-msg-events’. In response,
check-exception will return an event log containing an Pipe Events
message. This message contains the source ID for which this
message is intended to and the pipe status such as whether the
payload is pending in the hypervisor or pipe to source is closed.
If there is any user space process waiting in the wait_queue for
the payload from this source ID, wake up that process which can
issue read() to obtain payload with ibm,receive-hvpipe-msg RTAS
or close FD if the pipe to source is closed.
The hypervisor has one pipe per partition for all sources and it
will not deliver another hvpipe event message until the partition
reads the payload for the previous hvpipe event. So if the source
ID is not found in the source list, issue the dummy
ibm,receive-hvpipe-msg RTAS so that pipe will not blocked.
Register hvpipe event source interrupt based on entries from
/proc/device-tree//event-sources/ibm,hvpipe-msg-events property.
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Tested-by: Shashank MS <shashank.gowda@in.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250909084402.1488456-8-haren@linux.ibm.com
The user space polls on the wait_queue for the payload from the
specific source. The hypervisor interrupts the OS when the pipe
status for the specific source is changed such as payload is
available for the partition or pipe to the source is closed. The
OS retrieves the HVPIPE event message with check-exception RTAS
and event message contains the source ID and the pipe status.
Then wakes up all FDs waiting on the wait_queue so that the user
space can read the payload or close the FD if the pipe to source
in the hypervisor is closed.
The hypervisor assigns one pipe per partition for all sources.
Hence issue ibm,receive-hvpipe-msg() to read the pending
payload during release() before closing FD so that pipe to the
partition will not be blocked.
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Tested-by: Shashank MS <shashank.gowda@in.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250909084402.1488456-7-haren@linux.ibm.com
ibm,receive-hvpipe-msg RTAS call is used to receive data from the
source (Ex: Hardware Management Console) over the hypervisor
pipe. The hypervisor will signal the OS via a Hypervisor Pipe
Event external interrupt when data is available to be received
from the pipe and the event message has the source ID and the
message type such as payload or closed pipe to the specific
source. The hypervisor will not generate another interrupt for
the next payload until the partition reads the previous payload.
It means the hvpipe is blocked and will not deliver other events
for any source. The maximum data length of 4048 bytes is
supported with this RTAS call right now.
The user space uses read() to receive data from HMC which issues
ibm,receive-hvpipe-msg RTAS and the kernel returns the buffer
length (including papr_hvpipe_hdr length) to the user space for
success or RTAS failure error. If the message is regarding the
pipe closed, kernel just returns the papr_hvpipe_hdr with
flags = HVPIPE_LOST_CONNECTION and expects the user space to
close FD for the corresponding source.
ibm,receive-hvpipe-msg RTAS call passes the buffer and returns
the source ID from where this payload is received and the
payload length.
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Tested-by: Shashank MS <shashank.gowda@in.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250909084402.1488456-6-haren@linux.ibm.com
ibm,send-hvpipe-msg RTAS call is used to send data to the source
(Ex: Hardware Management Console) over the hypervisor pipe. The
maximum data length of 4048 bytes is supported with this RTAS call
right now. The user space uses write() to send this payload which
invokes this RTAS. Then the write returns the buffer length
(including papr_hvpipe_hdr length) to the user space for success
or RTAS failure error.
ibm,send-hvpipe-msg call takes source ID as target and the buffer
in the form of buffer list. The buffer list format consists of
work area of size 4K to hold buffer list and number of 4K work
areas depends on buffers is as follows:
Length of Buffer List in bytes
Address of 4K buffer 1
Length of 4K buffer 1 used
...
Address of 4K buffer n
Length of 4K buffer n used
Only one buffer is used right now because of max payload size is
4048 bytes. writev() can be used in future when supported more
than one buffer.
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Tested-by: Shashank MS <shashank.gowda@in.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250909084402.1488456-5-haren@linux.ibm.com
The hypervisor provides ibm,send-hvpipe-msg and
ibm,receive-hvpipe-msg RTAS calls which can be used by the
partition to communicate through an inband hypervisor channel with
different external sources such as Hardware Management Console
(HMC). The information exchanged, whether it be messages, raw or
formatted data, etc., is only known to between applications in the
OS and the source (HMC). This patch adds papr-hvpipe character
driver and provides the standard interfaces such as open / ioctl/
read / write to user space for exchanging information with HMC
using send/recevive HVPIPE RTAS functions.
PAPR (7.3.32 Hypervisor Pipe Information Exchange) defines the
HVPIPE usage:
- The hypervisor has one HVPIPE per partition for all sources.
- OS can determine this feature’s availability by detecting the
“ibm,hypervisor-pipe-capable” property in the /rtas node of the
device tree.
- Each source is represented by the source ID which is used in
send / recv HVPIPE RTAS. (Ex: source ID is the target for the
payload in send RTAS).
- Return status of ibm,send-hvpipe-msg can be considered as
delivered the payload.
- Return status of ibm,receive-hvpipe-msg can be considered as
ACK to source.
- The hypervisor generates hvpipe message event interrupt when
the partition has the payload to receive.
Provide the interfaces to the user space with /dev/papr-hvpipe
character device using the following programming model:
int devfd = open("/dev/papr-hvpipe")
int fd = ioctl(devfd, PAPR_HVPIPE_IOC_CREATE_HANDLE, &srcID);
- Restrict the user space to use the same source ID and do not
expect more than one process access with the same source.
char *buf = malloc(size);
- SIZE should be 4K and the buffer contains header and the
payload.
length = write(fd, buf, size);
- OS issues ibm,send-hvpipe-msg RTAS and returns the RTAS status
to the user space.
ret = poll(fd,...)
- The HVPIPE event message IRQ wakes up for any waiting FDs.
length = read(fd, buf, size);
- OS issues ibm,receive-hvpipe-msg to receive payload from the
hypervisor.
release(fd);
- OS issues ibm,receive-hvpipe-msg if any payload is pending so
that pipe is not blocked.
The actual implementation of these calls are added in the
next patches.
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Tested-by: Shashank MS <shashank.gowda@in.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250909084402.1488456-4-haren@linux.ibm.com
Define HVPIPE specific macros which are needed to support
ibm,send-hvpipe-msg and ibm,receive-hvpipe-msg RTAS calls
and used to handle HVPIPE message events.
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Tested-by: Shashank MS <shashank.gowda@in.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250909084402.1488456-3-haren@linux.ibm.com
PowerPC FW introduced HVPIPE RTAS calls such as
ibm,send-hvpipe-msg and ibm,receive-hvpipe-msg for the user space
to exchange information with different sources such as Hardware
Management Consoles (HMC).
HVPIPE_IOC_CREATE_HANDLE is defined to use /dev/papr-hvpipe
interface for ibm,send-hvpipe-msg and ibm,receive-hvpipe-msg
RTAS calls.
Also defined papr_hvpipe_hdr which will added in the payload
that is passed between the kernel and the user space.
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Tested-by: Shashank MS <shashank.gowda@in.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250909084402.1488456-2-haren@linux.ibm.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmjHMcoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG5bwH/23w8iGB4hf7L/7Z
e7blX42Pe9EXA1uK62iWmwEjDvBuJ7TmVfXH09qYJ56fj6/rJEdpQwtBMd4ypL81
QA/7lq5UEl0apPzMN86J8EHCzmjNzv7o+UtEd4C/hPFEZHZJa5Hqj9CBglSwSCEn
fTkLk7Gl6s8SfzBQ/rXX6/ZChAB/RleVWabDlIQMDz++/+9DZ0aqphj+5bYSqysL
ROQOaj4LOICuLfrup9J61hKNBoF7Dv3sO20vc+Iic0XHRPZ6/lKCnHgCUsqVIOOQ
L4kDT7XKQg+n3ttjrMe84/8iHZdWtf8VMWrtniPT8e1YGYuMpavVplgIcFoFCoNm
Qa7NPDs=
=rZeT
-----END PGP SIGNATURE-----
Merge tag 'v6.17-rc6' into drm-next
This is a backmerge of Linux 6.17-rc6, needed for msm,
also requested by misc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
mt76_eeprom_override has of_get_mac_address, which can return
-EPROBE_DEFER if the nvmem driver gets loaded after mt76 for some
reason.
Make sure this gets passed to probe so that nvmem mac overrides always
work.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20250911221619.16035-1-rosenp@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support writing MAC TXD for the AddBA Req. Without this commit, the
start sequence number in AddBA Req will be unexpected value for MT7996
and MT7992. This can result in certain stations (e.g., AX200) dropping
packets, leading to ping failures and degraded connectivity. Ensuring
the correct MAC TXD and TXP helps maintain reliable packet transmission
and prevents interoperability issues with affected stations.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Link: https://patch.msgid.link/20250909-mt7996-addba-txd-fix-v1-1-feec16f0c6f0@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In vendor driver, size of group cal and dpd cal for mt7981 includes 6G
although the chip doesn't support it.
mt76 doesn't take this into account which results in reading from the
incorrect offset.
For devices with precal, this would lead to lower bitrate.
Fix this by aligning groupcal size with vendor driver and switch to
freq_list_v2 in mt7915_dpd_freq_idx in order to get the correct offset.
Below are iwinfo of the test device with two clients connected
(iPhone 16, Intel AX210).
Before :
Mode: Master Channel: 36 (5.180 GHz) HT Mode: HE80
Center Channel 1: 42 2: unknown
Tx-Power: 23 dBm Link Quality: 43/70
Signal: -67 dBm Noise: -92 dBm
Bit Rate: 612.4 MBit/s
Encryption: WPA3 SAE (CCMP)
Type: nl80211 HW Mode(s): 802.11ac/ax/n
Hardware: embedded [MediaTek MT7981]
After:
Mode: Master Channel: 36 (5.180 GHz) HT Mode: HE80
Center Channel 1: 42 2: unknown
Tx-Power: 23 dBm Link Quality: 43/70
Signal: -67 dBm Noise: -92 dBm
Bit Rate: 900.6 MBit/s
Encryption: WPA3 SAE (CCMP)
Type: nl80211 HW Mode(s): 802.11ac/ax/n
Hardware: embedded [MediaTek MT7981]
Tested-on: mt7981 20240823
Fixes: 19a954edec ("wifi: mt76: mt7915: add mt7986, mt7916 and mt7981 pre-calibration")
Signed-off-by: Zhi-Jun You <hujy652@gmail.com>
Link: https://patch.msgid.link/20250909064824.16847-1-hujy652@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce HW-RRO v3.1 support to be reused when Wireless Ethernet
Dispatcher (WED) is not available. HW-RRO v3.1 is supported by
MT7992 chipset.
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-16-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_dma_get_rxdmad_c_buf routine to process packets received
by HW-RRO v3.1 module.
This is a preliminary patch to introduce SW path for HW-RRO v3.1 module
available on MT7992 chipset.
Co-developed-by: Rex Lu <rex.lu@mediatek.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-15-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Decouple RRO logic from WED support in MT7996 driver in order to reuse
it when WED module is not available.
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-14-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce rx_queue_init DMA callback. This is a preliminary patch to
configure RRO RX queues and decouple RRO logic from WED support.
Co-developed-by: Rex Lu <rex.lu@mediatek.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-13-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce rx_rro_ind_process and rx_rro_add_msdu_page callbacks and the
related logic in the MT7996 driver. This is a preliminary patch to
decouple RRO logic from WED support and reuse RRO when WED module is not
available.
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-12-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce WED offload support for MT7992 chipset in MT7996 driver.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-10-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to properly set the number of rx packets for primary WED device
if hif device is available, move hif pointer initialization before
running mt7996_mmio_wed_init routine.
Fixes: 83eafc9251 ("wifi: mt76: mt7996: add wed tx support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-9-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the second phy tx queue initialization if hif device is not
available for MT7990 chipset.
Fixes: 83eafc9251 ("wifi: mt76: mt7996: add wed tx support")
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Co-developed-by: Rex Lu <rex.lu@mediatek.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-8-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to enable WED support for MT7992 Kite
chipset supported by MT7996 driver.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-7-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to enable WED support for MT7992 Kite
chipset supported by MT7996 driver.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-6-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Manage differences in DMA and RX queues configuration for MT7992 and
MT7996.
This is a preliminary patch to enable WED support for MT7992 Kite
chipset supported by MT7996 driver.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-5-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to enable WED support for MT7992 Kite
chipset supported by MT7996 driver.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-3-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove __mt76_dma_queue_reset routine and use mt76_dma_queue_reset
directly instead in mt76_queue_ops struct.
This is a preliminary patch to enable WED support for MT7992 Kite
chipset supported by MT7996 driver.
Co-developed-by: Rex Lu <rex.lu@mediatek.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250909-mt7996-rro-rework-v5-1-7d66f6eb7795@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
EPCS is not yet ready, so do not claim to support it.
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250904-mt7996-mlo-more-fixes-v1-4-89d8fed67f20@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do the MLD to link address translation for EAPOL frames in driver.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250904-mt7996-mlo-more-fixes-v1-3-89d8fed67f20@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add all valid links to poll list for Airtime Fairness/AQL accounting when
tx-free event occurs.
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250904-mt7996-mlo-more-fixes-v1-2-89d8fed67f20@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update mt7996_reverse_frag0_hdr_trans routine to support MLO.
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250904-mt7996-mlo-more-fixes-v1-1-89d8fed67f20@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable 160MHz beamformee support on mt7922 by updating HE capability
element configuration. Previously, only 160MHz channel width was set,
but beamformee for 160MHz was not properly advertised. This patch
adds BEAMFORMEE_MAX_STS_ABOVE_80MHZ_4 capability to allow devices
to utilize 160MHz BW for beamforming.
Tested by connecting to 160MHz-bandwidth beamforming AP and verified
HE capability.
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Link: https://patch.msgid.link/ae637afaffed387018fdc43709470ef65898ff0b.1756383627.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Due to hibernation causing a power off and power on,
this modification adds mt7925_pci_restore callback function for kernel.
When hibernation resumes, it calls mt7925_pci_restore to reset the device,
allowing it to return to the state it was in before the power off.
Signed-off-by: Jack Kao <jack.kao@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250901073200.230033-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to avoid a possible NULL pointer dereference in
mt7996_mac_sta_init_link routine, move the phy pointer check before
running mt7996_mac_sta_init_link() in mt7996_mac_sta_add_links routine.
Fixes: dd82a9e02c ("wifi: mt76: mt7996: Rely on mt7996_sta_link in sta_add/sta_remove callbacks")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250830-mt7996_mac_sta_add_links-fix-v1-1-4219fb8755ee@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Packets belonging to the same TID can be sent over multiple links.
AMPDU rx reordering must be performed over all active links. Fix the
problem always using default link for AMPDU rx reordering.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250823-mt7996-mlo-aggr-fix-v1-1-f35cf0ea4c8a@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In mt76_wmac_probe(), when the mt76_alloc_device() call succeeds, memory
is allocated for both struct ieee80211_hw and a workqueue. However, on
the error path, the workqueue is not freed. Fix that by calling
mt76_free_device() on the error path.
Fixes: c8846e1015 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20250709145532.41246-1-abdun.nihaal@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
