P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
I2C Board 128x8 bit memory
SD/MMC connector to interface with the SD memory card
2 SATA interface
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221 eCAN
Two DB-9 female connectors for Field bus interface UART
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable framebuffer console support by default in the defconfig on the
Freescale MPC8610 HPCD reference board. This allows the boot messages to
be shown on the video display.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8610hpcd_set_pixel_clock() calculates the correct value of the PXCLK
bits in the CLKDVDR register for a given pixel clock rate. The code which
performs this calculation is overly complicated and includes an error
estimation routine that doesn't work most of the time anyway. Replace the
code with the simpler routine that's currently used on the P1022DS.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable framebuffer console support by default in the defconfigs for the
Freescale 85xx-based reference board. This allows the boot messages to
be shown on the video display on the P1022DS.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To ensure that the DIU pixel clock will not be set to an invalid value,
clamp the PXCLK divider to the allowed range (2-255). This also acts as
a limiter for the pixel clock.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
e500mc cannot doze or nap due to an erratum (as well as having a
different mechanism than previous e500), but it has a "wait" instruction
that is similar to doze.
On 64-bit, due to the soft-irq-disable mechanism, the existing
book3e_idle should be used instead.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The platform file for the Freecale P1022DS reference board is not freeing
the ioremap() mapping of the PIXIS and global utilities nodes it creates.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl-lbc driver requires an interrupt to bind to localbus device.
Populate 85xx boards' dts trees with lbc interrupt info.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL PCIe controller can act as agent(EP) or host(RC). Under Agent(EP) mode
the controller will be configured by the host system. So its not required
to be registered with the PCI(e) sub-system. We only register the
controller if its configured in host(RC) mode.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the ePAPR-compliant Freescale hypervisor (aka "Topaz") on
the Freescale P3041DS, P4080DS, and P5020DS reference boards.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add functions to restart and halt the current partition when running under
the Freescale hypervisor. These functions should be assigned to various
function pointers of the ppc_md structure during the .probe() function for
the board:
ppc_md.restart = fsl_hv_restart;
ppc_md.power_off = fsl_hv_halt;
ppc_md.halt = fsl_hv_halt;
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale ePAPR reference hypervisor provides interrupt controller
services via a hypercall interface, instead of emulating the MPIC
controller. This is called the VMPIC.
The ePAPR "virtual interrupt controller" provides interrupt controller
services for external interrupts. External interrupts received by a
partition can come from two sources:
- Hardware interrupts - hardware interrupts come from external
interrupt lines or on-chip I/O devices.
- Virtual interrupts - virtual interrupts are generated by the hypervisor
as part of some hypervisor service or hypervisor-created virtual device.
Both types of interrupts are processed using the same programming model and
same set of hypercalls.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
ePAPR hypervisors provide operating system services via a "hypercall"
interface. The following steps need to be performed to make an hcall:
1. Load r11 with the hcall number
2. Load specific other registers with parameters
3. Issue instrucion "sc 1"
4. The return code is in r3
5. Other returned parameters are in other registers.
To provide this service to the kernel, these steps are wrapped in inline
assembly functions. Standard ePAPR hcalls are in epapr_hcalls.h, and
Freescale extensions are in fsl_hcalls.h.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A simple implementation that only supports the word size and does not
have a fallback mode (would require a spinlock).
Add 32 and 64 bit support for cmpxchg_double. cmpxchg double uses
the cmpxchg8b or cmpxchg16b instruction on x86 processors to compare
and swap 2 machine words. This allows lockless algorithms to move more
context information through critical sections.
Set a flag CONFIG_CMPXCHG_DOUBLE to signal that support for double word
cmpxchg detection has been build into the kernel. Note that each subsystem
using cmpxchg_double has to implement a fall back mechanism as long as
we offer support for processors that do not implement cmpxchg_double.
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Christoph Lameter <cl@linux.com>
Link: http://lkml.kernel.org/r/20110601172614.173427964@linux.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Hello,
I am not 100% sure this is the right thing to do, but it makes the
atmel-ssc driver happy on my at91rm9200 board.
This unifies the con_id across all at91 machines.
The atmel-ssc driver expects the con_id to be "pclk" or it will fail probing.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI/ACPI: fix type mismatch
PCI: fix new kernel-doc warning
PCI: Fix warning in drivers/pci/probe.c on sparc64
This is a partial revert of e44ba033c5 ("treewide: remove duplicate
includes").
The file is gone in s390 tree and will not exist any more.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Ensure that our temporary page table entry is flushed from the TLB
before we resume normal operations. This ensures that userspace
won't trip over the stale TLB entry.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The first and second arguments shouldn't concern platform code, so
hide them from each platforms caller.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Upon return from off-mode, the ROM code jumps to a restore function
saved in the scratchpad. Based on SoC revision or errata, this
restore entry point is different. Current code uses some helper
functions in sleep34xx.S (get_*_restore_pointer) to get the restore
function entry point.
When returning from off-mode, this code is executed from SDRAM, so
there's no reason to use these helper functions when using the SDRAM
entry points directly would work just fine.
This patch uses ENTRY/ENDPROC to create "real" entry points for these
functions, and uses those values directly when writing the scratchpad.
Tested all three entry points
- restore_es3: 3430/n900
- restore_3630: 3630/Zoom3
- restore: 3530/Overo
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Because the USB EHCI/OHCI driver has new configuration for SH,
the patch enables the EHCI and/or OHCI driver of the on-chip for
some CPUs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
clk_get() used to return NULL or an errno value depending on whether a
clkdev lookup failed or a clock wasn't found in the primary clock list.
As these disjoint paths were unified and everything now is handled via
clkdev lookups, the NULL case never makes it out of clk_get(). Update
accordingly and always look to the errno value.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert omap34xx to use the generic CPU suspend/resume support, rather
than implementing its own version. Tested on 3430 LDP.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The code alludes to r9 being used to indicate what was lost over the
suspend/resume transition. However, although r9 is set, it is never
actually used.
Also, the comments before the code (which refer to the value of r9)
and the comments against the assignment of r9 contradict each other,
so just remove them to avoid confusion.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ABI allows called functions to corrupt r0-r3 and ip (r12). So
its pointless saving these registers in the suspend code - the
calling function will expect them to be corrupted and so won't rely
on their contents after resume.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need a veneer for cpu_suspend, it can be called directly from
C code now. Move it into the PXA CPU suspend functions, along with
the accumulator register saving/restoring.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The core suspend code calls flush_cache_all() immediately prior to
calling the suspend finisher function, so remove these needless calls
from the finisher functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the call to cpu_suspend into C code, and noticing that all the
s3c_cpu_save implementations are now identical, we can move this
into the common samsung code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
s3c_cpu_save does not need to save any registers with the new
cpu_suspend calling convention. Remove these redundant instructions.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
s3c_cpu_save does not need to save any registers with the new
cpu_suspend calling convention. Remove these redundant instructions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
s3c_cpu_save does not need to save any registers with the new
cpu_suspend calling convention. Remove these redundant instructions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
s3c_cpu_save does not need to save any registers with the new
cpu_suspend calling convention. Remove these redundant instructions.
Tested-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need a veneer for cpu_suspend, it can be called directly from
C code now. Move it into sa11x0_pm_enter() along with the re-enabling
of clock switching.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As we have core code dealing with CPU suspend/resume, we can
re-initialize the CPUs exception banked registers via that code rather
than having platforms deal with that level of detail. So, move the
call to cpu_init() out of platform code into core code.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cpu_suspend() has a weird calling method which makes it only possible to
call from assembly code: it returns with a modified stack pointer to
finish the suspend, but on resume, it 'returns' via a provided pointer.
We can make cpu_suspend() appear to be a normal function merely by
swapping the resume pointer argument and the link register.
Do so, and update all callers to take account of this more traditional
behaviour.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the previous commit, we introduced an official way to supply an
argument to the suspend function. Convert the sa1100 suspend code
to use this method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Save the suspend function pointer onto the stack for use when returning.
Allocate r2 to pass an argument to the suspend function.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid using r2 and r3 in the suspend code, allowing these to be
passed further into the function as arguments.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make cpu_suspend()..return function preserve r4 to r11 across a suspend
cycle. This is in preparation of relieving platform support code from
this task.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Very little code is different between these two paths now, so extract
the common code.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the return address for cpu_resume to the top of stack so that
cpu_resume looks more like a normal function.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eliminate the differences between MULTI_CPU and non-MULTI_CPU resume
paths, making the saved structure identical irrespective of the way
the kernel was configured.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
