This patch adds ARCH_HAS_CPUFREQ in Kconfig of ARCH_S5PV310 and updates
Makefile for supporting build S5PV310 CPUFREQ driver.
Signed-off-by: Sunyoung Kang <sy0816.kang@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
FOUT APLL clock is used as a source of ARM core clock. So we need that the
clock source can be changed dynamically by using CPUFREQ driver. This patch
can give correct frequency when calling clk_get_rate() function.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangwook Ju <sw.ju@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates following of CPUFREQ.
- Updated DVFS table and divider value
- Added common function
- Added some function for changing APLL and setting
Signed-off-by: Sangwook Ju <sw.ju@samsung.com>
Reviewed-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support CPUFREQ driver for S5PV310 and S5PC210. This can
support DVFS(Dynamic Voltage and Frequency Scaling). The voltage scaling
depends on existence of regulator.
Sigend-off-by: Sunyoung Kang <sy0816.kang@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds DMC io mapping for access it and adds registers.
This is used in checking DRAM memory type.
Signed-off-by: Sunyoung Kang <sy0816.kang@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds missing CMU(Clock Management Unit) registers for
updated S5PV310 CPUFREQ driver.
Signed-off-by: Sangwook Ju <sw.ju@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds CMU(Clock Management Unit) registers for S5PV310/S5PC210
CPUFREQ driver and modifies some register names according to datasheet.
Signed-off-by: Sunyoung Kang <sy0816.kang@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use omap_serial_init_port so we can let the serial code handle the
remuxing of the RX pads. Note that this patch alone is not enough
and additional GPIO related patches are needed.
Only initialize uart3_rx_irrx pin, the other uart pins can be
stay static.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow hwmod state changes to mux pads based on the state changes.
By default, only enable and disable the pads. In some rare cases
dynamic remuxing for the idles states is needed, this can be done
by passing the enable, idle, and off pads from board-*.c file along
with OMAP_DEVICE_PAD_REMUX flag.
Thanks to Paul Walmsley <paul@booyaka.com> for the comments on the
hwmod related changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows adding hwmod specific pads dynamically during the
platform device init.
Note that we don't currently have the hwmod specific signals
listed in the hwmod data, but struct omap_hwmod_mux_info will
make that possible if necessary.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do this by splitting _omap_mux_init_signal as it already has most
of the necessary features.
Based on an earlier patch by Dan Murphy <dmurphy@ti.com>.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When CONFIG_SUSPEND is not enabled, none of the system PM methods are
used, so do not compile them in.
Thanks to Charles Manning for reporting the problem and proposing
an initial patch.
Reported-by: Charles Manning <manningc2@actrix.gen.nz>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert versatile platforms to use the new sched_clock() infrastructure
for extending 32bit counters to full 64-bit nanoseconds.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert orion platforms to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert omap to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert nomadik platforms to use the new sched_clock() infrastructure
for extending 32bit counters to full 64-bit nanoseconds.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert iop platforms to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert u300 to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert tegra to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert sa1100 to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert pxa to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert mmp to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert ixp4xx to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide common sched_clock() infrastructure for platforms to use to
create a 64-bit ns based sched_clock() implementation from a counter
running at a non-variable clock rate.
This implementation is based upon maintaining an epoch for the counter
and an epoch for the nanosecond time. When we desire a sched_clock()
time, we calculate the number of counter ticks since the last epoch
update, convert this to nanoseconds and add to the epoch nanoseconds.
We regularly refresh these epochs within the counter wrap interval.
We perform a similar calculation as above, and store the new epochs.
We read and write the epochs in such a way that sched_clock() can easily
(and locklessly) detect when an update is in progress, and repeat the
loading of these constants when they're known not to be stable. The
one caveat is that sched_clock() is not called in the middle of an
update. We achieve that by disabling IRQs.
Finally, if the clock rate is known at compile time, the counter to ns
conversion factors can be specified, allowing sched_clock() to be tightly
optimized. We ensure that these factors are correct by providing an
initialization function which performs a run-time check.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ftrace requires sched_clock() to be notrace. Ensure that all
implementations are so marked. Also make sure that they include
linux/sched.h
Also ensure OMAP clocksource read functions are marked notrace as
they're used for sched_clock() too.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
tegra_clocksource_read should not use cnt32_to_63, wrapping is
already handled in the clocksource code. Move the cnt32_to_63
into the sched_clock function, and replace the use of clocksource
mult and shift with a multiplication by 1000 to convert us to ns.
Acked-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Wan zongshun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-By: Jeff Ohlstein <johlstei@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
